[PATCH v2 00/11] arm64: prepare and add verdin imx8m mini support

[PATCH v2 00/11] arm64: prepare and add verdin imx8m mini support

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>


Fix strange hex notation and gpio-hog example, rebuild default
configuration, enable various relevant configuration options mainly to
be built as modules, add toradex,verdin-imx8mm et al. to dt-bindings and
finally, add initial support for Verdin iMX8M Mini.

Changes in v2:
- Added Laurent's reviewed-by tag.
- Added Rob's ack.
- New patch following full defconfig analysis as requested by Krzysztof.
- New patch following full defconfig analysis as requested by Krzysztof.
- Done full defconfig analysis as requested by Krzysztof.
- Add Song's acked-by tag.
- A similar change got accepted for imx_v6_v7_defconfig. Further
discussion may be found in [1].
[1] https://lore.kernel.org/lkml/20210920144938.314588-6-marcel@ziswiler.com/
- Explain why enabling it may be a good idea as requested by Krzysztof.
- Explain why enabling these may make sense and squash them relevant
  changes as requested by Krzysztof.
- Add Rob's acked-by tag.
- Fix Colibri vs. Verdin copy/paste mistake. Thanks to Francesco Dolcini
  <francesco.dolcini@toradex.com> for pointing that out to me.
- Remove bootargs which will be filled in by the bootloader as requested
  by Krzysztof.
- Remove the previously #ifdefed-out spi-nor as requested by Krzysztof.
- Fix capitalisation in cover-letter.

Marcel Ziswiler (11):
  arm64: dts: imx8mm: fix strange hex notation
  dt-bindings: gpio: fix gpio-hog example
  arm64: defconfig: enable taskstats configuration
  arm64: defconfig: enable pcieaer configuration
  arm64: defconfig: rebuild default configuration
  arm64: defconfig: enable bpf/cgroup firewalling
  arm64: defconfig: build imx-sdma as a module
  arm64: defconfig: build r8169 as a module
  arm64: defconfig: enable verdin-imx8mm relevant drivers as modules
  dt-bindings: arm: fsl: add toradex,verdin-imx8mm et al.
  arm64: dts: freescale: add initial support for verdin imx8m mini

 .../devicetree/bindings/arm/fsl.yaml          |   21 +
 .../devicetree/bindings/gpio/gpio.txt         |    2 +-
 arch/arm64/boot/dts/freescale/Makefile        |    4 +
 .../arm64/boot/dts/freescale/imx8mm-pinfunc.h |    6 +-
 .../dts/freescale/imx8mm-verdin-dahlia.dtsi   |  143 ++
 .../boot/dts/freescale/imx8mm-verdin-dev.dtsi |   67 +
 .../imx8mm-verdin-nonwifi-dahlia.dts          |   18 +
 .../freescale/imx8mm-verdin-nonwifi-dev.dts   |   18 +
 .../dts/freescale/imx8mm-verdin-nonwifi.dtsi  |   75 +
 .../freescale/imx8mm-verdin-wifi-dahlia.dts   |   18 +
 .../dts/freescale/imx8mm-verdin-wifi-dev.dts  |   18 +
 .../dts/freescale/imx8mm-verdin-wifi.dtsi     |   95 ++
 .../boot/dts/freescale/imx8mm-verdin.dtsi     | 1267 +++++++++++++++++
 arch/arm64/configs/defconfig                  |  123 +-
 14 files changed, 1806 insertions(+), 69 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi

-- 
2.33.1

[PATCH v2 01/11] arm64: dts: imx8mm: fix strange hex notation

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Fix strange hex notation with mixed lower-case and upper-case letters.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

---

Changes in v2:
- Added Laurent's reviewed-by tag.

 arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h b/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
index a003e6af3353..c68a5e456025 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
+++ b/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
@@ -279,7 +279,7 @@
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI1_TX_DATA4                                0x150 0x3B8 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI1_TX_SYNC                                 0x150 0x3B8 0x4CC 0x2 0x1
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK                                 0x150 0x3B8 0x4E8 0x3 0x0
-#define MX8MM_IOMUXC_SAI5_RXD2_PDM_DATA2                                    0x150 0x3B8 0x53c 0x4 0x0
+#define MX8MM_IOMUXC_SAI5_RXD2_PDM_DATA2                                    0x150 0x3B8 0x53C 0x4 0x0
 #define MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23                                   0x150 0x3B8 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI5_RXD3_SAI5_RX_DATA3                                0x154 0x3BC 0x4E0 0x0 0x0
 #define MX8MM_IOMUXC_SAI5_RXD3_SAI1_TX_DATA5                                0x154 0x3BC 0x000 0x1 0x0
@@ -486,7 +486,7 @@
 #define MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC                                 0x1D8 0x440 0x000 0x0 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_GPT1_CAPTURE2                                0x1D8 0x440 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_SAI5_RX_DATA1                                0x1D8 0x440 0x4D8 0x2 0x2
-#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX                                 0x1D8 0x440 0x4Fc 0x4 0x2
+#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX                                 0x1D8 0x440 0x4FC 0x4 0x2
 #define MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX                                 0x1D8 0x440 0x000 0x4 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31                                   0x1D8 0x440 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_TPSMP_HDATA1                                 0x1D8 0x440 0x000 0x7 0x0
@@ -494,7 +494,7 @@
 #define MX8MM_IOMUXC_SAI3_TXC_GPT1_COMPARE2                                 0x1DC 0x444 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI3_TXC_SAI5_RX_DATA2                                 0x1DC 0x444 0x4DC 0x2 0x2
 #define MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX                                  0x1DC 0x444 0x000 0x4 0x0
-#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX                                  0x1DC 0x444 0x4Fc 0x4 0x3
+#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX                                  0x1DC 0x444 0x4FC 0x4 0x3
 #define MX8MM_IOMUXC_SAI3_TXC_GPIO5_IO0                                     0x1DC 0x444 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI3_TXC_TPSMP_HDATA2                                  0x1DC 0x444 0x000 0x7 0x0
 #define MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0                                 0x1E0 0x448 0x000 0x0 0x0
-- 
2.33.1

[PATCH v2 01/11] arm64: dts: imx8mm: fix strange hex notation

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Fix strange hex notation with mixed lower-case and upper-case letters.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

---

Changes in v2:
- Added Laurent's reviewed-by tag.

 arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h b/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
index a003e6af3353..c68a5e456025 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
+++ b/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
@@ -279,7 +279,7 @@
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI1_TX_DATA4                                0x150 0x3B8 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI1_TX_SYNC                                 0x150 0x3B8 0x4CC 0x2 0x1
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK                                 0x150 0x3B8 0x4E8 0x3 0x0
-#define MX8MM_IOMUXC_SAI5_RXD2_PDM_DATA2                                    0x150 0x3B8 0x53c 0x4 0x0
+#define MX8MM_IOMUXC_SAI5_RXD2_PDM_DATA2                                    0x150 0x3B8 0x53C 0x4 0x0
 #define MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23                                   0x150 0x3B8 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI5_RXD3_SAI5_RX_DATA3                                0x154 0x3BC 0x4E0 0x0 0x0
 #define MX8MM_IOMUXC_SAI5_RXD3_SAI1_TX_DATA5                                0x154 0x3BC 0x000 0x1 0x0
@@ -486,7 +486,7 @@
 #define MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC                                 0x1D8 0x440 0x000 0x0 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_GPT1_CAPTURE2                                0x1D8 0x440 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_SAI5_RX_DATA1                                0x1D8 0x440 0x4D8 0x2 0x2
-#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX                                 0x1D8 0x440 0x4Fc 0x4 0x2
+#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX                                 0x1D8 0x440 0x4FC 0x4 0x2
 #define MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX                                 0x1D8 0x440 0x000 0x4 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31                                   0x1D8 0x440 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_TPSMP_HDATA1                                 0x1D8 0x440 0x000 0x7 0x0
@@ -494,7 +494,7 @@
 #define MX8MM_IOMUXC_SAI3_TXC_GPT1_COMPARE2                                 0x1DC 0x444 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI3_TXC_SAI5_RX_DATA2                                 0x1DC 0x444 0x4DC 0x2 0x2
 #define MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX                                  0x1DC 0x444 0x000 0x4 0x0
-#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX                                  0x1DC 0x444 0x4Fc 0x4 0x3
+#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX                                  0x1DC 0x444 0x4FC 0x4 0x3
 #define MX8MM_IOMUXC_SAI3_TXC_GPIO5_IO0                                     0x1DC 0x444 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI3_TXC_TPSMP_HDATA2                                  0x1DC 0x444 0x000 0x7 0x0
 #define MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0                                 0x1E0 0x448 0x000 0x0 0x0
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 02/11] dt-bindings: gpio: fix gpio-hog example

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Even if this is no yaml yet at least fix the example to be compliant to
later schema as e.g. found in gpio-pca95xx.yaml, fairchild,74hc595.yaml
and gpio/fsl-imx-gpio.yaml.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>

---

Changes in v2:
- Added Rob's ack.

 Documentation/devicetree/bindings/gpio/gpio.txt | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index a8895d339bfe..5663e71b751f 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -213,7 +213,7 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
 		gpio-controller;
 		#gpio-cells = <2>;
 
-		line_b {
+		line_b-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			output-low;
-- 
2.33.1

[PATCH v2 02/11] dt-bindings: gpio: fix gpio-hog example

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Even if this is no yaml yet at least fix the example to be compliant to
later schema as e.g. found in gpio-pca95xx.yaml, fairchild,74hc595.yaml
and gpio/fsl-imx-gpio.yaml.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>

---

Changes in v2:
- Added Rob's ack.

 Documentation/devicetree/bindings/gpio/gpio.txt | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index a8895d339bfe..5663e71b751f 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -213,7 +213,7 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
 		gpio-controller;
 		#gpio-cells = <2>;
 
-		line_b {
+		line_b-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			output-low;
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 03/11] arm64: defconfig: enable taskstats configuration

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Enable CONFIG_TASKSTATS which is required for CONFIG_TASK_XACCT (and
subsequently CONFIG_TASK_IO_ACCOUNTING). Previously, taskstats got
pulled in by KVM but that got changed in commit 63b3f96e1a98
("kvm: Select SCHED_INFO instead of TASK_DELAY_ACCT").

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- New patch following full defconfig analysis as requested by Krzysztof.

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index cc5d3ba166b1..dec189229c0a 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -7,6 +7,7 @@ CONFIG_PREEMPT=y
 CONFIG_IRQ_TIME_ACCOUNTING=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
 CONFIG_TASK_XACCT=y
 CONFIG_TASK_IO_ACCOUNTING=y
 CONFIG_IKCONFIG=y
-- 
2.33.1

[PATCH v2 03/11] arm64: defconfig: enable taskstats configuration

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Enable CONFIG_TASKSTATS which is required for CONFIG_TASK_XACCT (and
subsequently CONFIG_TASK_IO_ACCOUNTING). Previously, taskstats got
pulled in by KVM but that got changed in commit 63b3f96e1a98
("kvm: Select SCHED_INFO instead of TASK_DELAY_ACCT").

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- New patch following full defconfig analysis as requested by Krzysztof.

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index cc5d3ba166b1..dec189229c0a 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -7,6 +7,7 @@ CONFIG_PREEMPT=y
 CONFIG_IRQ_TIME_ACCOUNTING=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
 CONFIG_TASK_XACCT=y
 CONFIG_TASK_IO_ACCOUNTING=y
 CONFIG_IKCONFIG=y
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
changed it to no longer being enabled by default.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- New patch following full defconfig analysis as requested by Krzysztof.

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index dec189229c0a..7daf2de6c31a 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -211,6 +211,7 @@ CONFIG_NFC_NCI=m
 CONFIG_NFC_S3FWRN5_I2C=m
 CONFIG_PCI=y
 CONFIG_PCIEPORTBUS=y
+CONFIG_PCIEAER=y
 CONFIG_PCI_IOV=y
 CONFIG_PCI_PASID=y
 CONFIG_HOTPLUG_PCI=y
-- 
2.33.1

[PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
changed it to no longer being enabled by default.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- New patch following full defconfig analysis as requested by Krzysztof.

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index dec189229c0a..7daf2de6c31a 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -211,6 +211,7 @@ CONFIG_NFC_NCI=m
 CONFIG_NFC_S3FWRN5_I2C=m
 CONFIG_PCI=y
 CONFIG_PCIEPORTBUS=y
+CONFIG_PCIEAER=y
 CONFIG_PCI_IOV=y
 CONFIG_PCI_PASID=y
 CONFIG_HOTPLUG_PCI=y
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Run "make defconfig; make savedefconfig" to rebuild defconfig.

This re-ordered the following configuration options:

CONFIG_BPF_JIT=y
CONFIG_ARM_SCMI_PROTOCOL=y
CONFIG_ARM_SCPI_PROTOCOL=y
CONFIG_RASPBERRYPI_FIRMWARE=y
CONFIG_INTEL_STRATIX10_SERVICE=y
CONFIG_INTEL_STRATIX10_RSU=m
CONFIG_EFI_CAPSULE_LOADER=y
CONFIG_IMX_SCU=y
CONFIG_IMX_SCU_PD=y
CONFIG_CAN_FLEXCAN=m
CONFIG_PCIE_LAYERSCAPE_GEN4=y
CONFIG_MTK_DEVAPC=m
CONFIG_SPI_CADENCE_QUADSPI=y
CONFIG_MDIO_BUS_MUX_MMIOREG=y
CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
CONFIG_MESON_GXL_PHY=m
CONFIG_QCOM_CPR=y
CONFIG_ROCKCHIP_IODOMAIN=y
CONFIG_SENSORS_ARM_SCMI=y
CONFIG_QORIQ_THERMAL=m
CONFIG_SUN8I_THERMAL=y
CONFIG_TEGRA_BPMP_THERMAL=m
CONFIG_ARM_SMC_WATCHDOG=y
CONFIG_VIDEO_QCOM_CAMSS=m
CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
CONFIG_DRM_NWL_MIPI_DSI=m
CONFIG_DRM_LONTIUM_LT9611UXC=m
CONFIG_SND_SOC_IMX_AUDMIX=m
CONFIG_TYPEC_HD3SS3220=m
CONFIG_COMMON_CLK_SCMI=y
CONFIG_IPQ_GCC_8074=y
CONFIG_SM_DISPCC_8250=y
CONFIG_QCOM_WCNSS_CTRL=m
CONFIG_ARCH_R8A774A1=y
CONFIG_ARCH_R8A774B1=y
CONFIG_ARCH_R8A774C0=y
CONFIG_ARCH_R8A774E1=y
CONFIG_ARCH_R8A77995=y
CONFIG_ARCH_R8A77990=y
CONFIG_ARCH_R8A77965=y
CONFIG_ARCH_R8A77970=y
CONFIG_HISI_PMU=y
CONFIG_QCOM_QFPROM=y
CONFIG_MUX_MMIO=y

And dropped the following configuration options which are nowaday's
already enabled (resp. disabled) by default:

CONFIG_MEMCG_SWAP=y
CONFIG_SECCOMP=y
CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
CONFIG_QCOM_SCM=y
# CONFIG_BT_HS is not set
CONFIG_FSL_MC_BUS=y
CONFIG_MEDIA_CONTROLLER=y
CONFIG_VIDEO_V4L2_SUBDEV_API=y
CONFIG_SND_SOC_FSL_SAI=m
CONFIG_USB_CONN_GPIO=m
CONFIG_USB_XHCI_PCI=m
CONFIG_MFD_CROS_EC_DEV=y
CONFIG_COMMON_CLK_ZYNQMP=y
CONFIG_SDM_GCC_845=y
CONFIG_SM_GCC_8150=y
CONFIG_SM_GCC_8250=y
CONFIG_SLIMBUS=m
CONFIG_INTERCONNECT=y
CONFIG_CONFIGFS_FS=y

CONFIG_POWER_AVS was renamed to POWER_AVS_OMAP in commit bca815d62054
("PM: AVS: smartreflex Move driver to soc specific drivers"). As there
are no 64-bit Arm OMAPs it getting dropped seems fair.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Done full defconfig analysis as requested by Krzysztof.

 arch/arm64/configs/defconfig | 108 ++++++++++++++---------------------
 1 file changed, 44 insertions(+), 64 deletions(-)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 7daf2de6c31a..bc39559c1658 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -3,6 +3,7 @@ CONFIG_POSIX_MQUEUE=y
 CONFIG_AUDIT=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BPF_JIT=y
 CONFIG_PREEMPT=y
 CONFIG_IRQ_TIME_ACCOUNTING=y
 CONFIG_BSD_PROCESS_ACCT=y
@@ -14,7 +15,6 @@ CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_NUMA_BALANCING=y
 CONFIG_MEMCG=y
-CONFIG_MEMCG_SWAP=y
 CONFIG_BLK_CGROUP=y
 CONFIG_CGROUP_PIDS=y
 CONFIG_CGROUP_HUGETLB=y
@@ -67,7 +67,6 @@ CONFIG_ARM64_VA_BITS_48=y
 CONFIG_SCHED_MC=y
 CONFIG_SCHED_SMT=y
 CONFIG_NUMA=y
-CONFIG_SECCOMP=y
 CONFIG_KEXEC=y
 CONFIG_KEXEC_FILE=y
 CONFIG_CRASH_DUMP=y
@@ -85,7 +84,6 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
 CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
-CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
 CONFIG_CPUFREQ_DT=y
 CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_ARM_ALLWINNER_SUN50I_CPUFREQ_NVMEM=m
@@ -98,15 +96,6 @@ CONFIG_ARM_RASPBERRYPI_CPUFREQ=m
 CONFIG_ARM_SCMI_CPUFREQ=y
 CONFIG_ARM_TEGRA186_CPUFREQ=y
 CONFIG_QORIQ_CPUFREQ=y
-CONFIG_ARM_SCMI_PROTOCOL=y
-CONFIG_ARM_SCPI_PROTOCOL=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_INTEL_STRATIX10_SERVICE=y
-CONFIG_INTEL_STRATIX10_RSU=m
-CONFIG_QCOM_SCM=y
-CONFIG_EFI_CAPSULE_LOADER=y
-CONFIG_IMX_SCU=y
-CONFIG_IMX_SCU_PD=y
 CONFIG_ACPI=y
 CONFIG_ACPI_APEI=y
 CONFIG_ACPI_APEI_GHES=y
@@ -183,14 +172,12 @@ CONFIG_NET_ACT_GATE=m
 CONFIG_QRTR=m
 CONFIG_QRTR_SMD=m
 CONFIG_QRTR_TUN=m
-CONFIG_BPF_JIT=y
 CONFIG_CAN=m
+CONFIG_CAN_FLEXCAN=m
 CONFIG_CAN_RCAR=m
 CONFIG_CAN_RCAR_CANFD=m
-CONFIG_CAN_FLEXCAN=m
 CONFIG_BT=m
 CONFIG_BT_HIDP=m
-# CONFIG_BT_HS is not set
 # CONFIG_BT_LE is not set
 CONFIG_BT_LEDS=y
 # CONFIG_BT_DEBUGFS is not set
@@ -230,7 +217,6 @@ CONFIG_PCIE_ROCKCHIP_HOST=m
 CONFIG_PCIE_BRCMSTB=m
 CONFIG_PCI_IMX6=y
 CONFIG_PCI_LAYERSCAPE=y
-CONFIG_PCIE_LAYERSCAPE_GEN4=y
 CONFIG_PCI_HISI=y
 CONFIG_PCIE_QCOM=y
 CONFIG_PCIE_ARMADA_8K=y
@@ -238,6 +224,7 @@ CONFIG_PCIE_KIRIN=y
 CONFIG_PCIE_HISI_STB=y
 CONFIG_PCIE_TEGRA194_HOST=m
 CONFIG_PCIE_VISCONTI_HOST=y
+CONFIG_PCIE_LAYERSCAPE_GEN4=y
 CONFIG_PCI_ENDPOINT=y
 CONFIG_PCI_ENDPOINT_CONFIGFS=y
 CONFIG_PCI_EPF_TEST=m
@@ -245,8 +232,15 @@ CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_FW_LOADER_USER_HELPER=y
 CONFIG_HISILICON_LPC=y
-CONFIG_FSL_MC_BUS=y
 CONFIG_TEGRA_ACONNECT=m
+CONFIG_ARM_SCMI_PROTOCOL=y
+CONFIG_ARM_SCPI_PROTOCOL=y
+CONFIG_RASPBERRYPI_FIRMWARE=y
+CONFIG_INTEL_STRATIX10_SERVICE=y
+CONFIG_INTEL_STRATIX10_RSU=m
+CONFIG_EFI_CAPSULE_LOADER=y
+CONFIG_IMX_SCU=y
+CONFIG_IMX_SCU_PD=y
 CONFIG_GNSS=m
 CONFIG_GNSS_MTK_SERIAL=m
 CONFIG_MTD=y
@@ -266,8 +260,6 @@ CONFIG_MTD_NAND_MARVELL=y
 CONFIG_MTD_NAND_FSL_IFC=y
 CONFIG_MTD_NAND_QCOM=y
 CONFIG_MTD_SPI_NOR=y
-CONFIG_MTK_DEVAPC=m
-CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=m
 CONFIG_VIRTIO_BLK=y
@@ -353,13 +345,11 @@ CONFIG_SNI_NETSEC=y
 CONFIG_STMMAC_ETH=m
 CONFIG_TI_K3_AM65_CPSW_NUSS=y
 CONFIG_QCOM_IPA=m
-CONFIG_MDIO_BUS_MUX_MMIOREG=y
-CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
+CONFIG_MESON_GXL_PHY=m
 CONFIG_AQUANTIA_PHY=y
 CONFIG_BCM54140_PHY=m
 CONFIG_MARVELL_PHY=m
 CONFIG_MARVELL_10G_PHY=m
-CONFIG_MESON_GXL_PHY=m
 CONFIG_MICREL_PHY=y
 CONFIG_MICROSEMI_PHY=y
 CONFIG_AT803X_PHY=y
@@ -367,6 +357,8 @@ CONFIG_REALTEK_PHY=y
 CONFIG_ROCKCHIP_PHY=y
 CONFIG_DP83867_PHY=y
 CONFIG_VITESSE_PHY=y
+CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
+CONFIG_MDIO_BUS_MUX_MMIOREG=y
 CONFIG_USB_PEGASUS=m
 CONFIG_USB_RTL8150=m
 CONFIG_USB_RTL8152=m
@@ -474,6 +466,7 @@ CONFIG_SPI=y
 CONFIG_SPI_ARMADA_3700=y
 CONFIG_SPI_BCM2835=m
 CONFIG_SPI_BCM2835AUX=m
+CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_SPI_DESIGNWARE=m
 CONFIG_SPI_DW_DMA=y
 CONFIG_SPI_DW_MMIO=m
@@ -545,9 +538,6 @@ CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_BD9571MWV=m
 CONFIG_GPIO_MAX77620=y
 CONFIG_GPIO_SL28CPLD=m
-CONFIG_POWER_AVS=y
-CONFIG_QCOM_CPR=y
-CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_POWER_RESET_MSM=y
 CONFIG_POWER_RESET_QCOM_PON=m
 CONFIG_POWER_RESET_XGENE=y
@@ -555,10 +545,10 @@ CONFIG_POWER_RESET_SYSCON=y
 CONFIG_SYSCON_REBOOT_MODE=y
 CONFIG_BATTERY_SBS=m
 CONFIG_BATTERY_BQ27XXX=y
-CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_BATTERY_MAX17042=m
 CONFIG_CHARGER_BQ25890=m
 CONFIG_CHARGER_BQ25980=m
+CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_SENSORS_ARM_SCPI=y
 CONFIG_SENSORS_JC42=m
 CONFIG_SENSORS_LM90=m
@@ -570,10 +560,10 @@ CONFIG_SENSORS_INA3221=m
 CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
 CONFIG_THERMAL_EMULATION=y
-CONFIG_QORIQ_THERMAL=m
-CONFIG_SUN8I_THERMAL=y
 CONFIG_IMX_SC_THERMAL=m
 CONFIG_IMX8MM_THERMAL=m
+CONFIG_QORIQ_THERMAL=m
+CONFIG_SUN8I_THERMAL=y
 CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_RCAR_THERMAL=y
 CONFIG_RCAR_GEN3_THERMAL=y
@@ -582,8 +572,8 @@ CONFIG_BCM2711_THERMAL=m
 CONFIG_BCM2835_THERMAL=m
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_EXYNOS_THERMAL=y
-CONFIG_TEGRA_BPMP_THERMAL=m
 CONFIG_TEGRA_SOCTHERM=m
+CONFIG_TEGRA_BPMP_THERMAL=m
 CONFIG_QCOM_TSENS=y
 CONFIG_QCOM_SPMI_TEMP_ALARM=m
 CONFIG_QCOM_LMH=m
@@ -592,7 +582,6 @@ CONFIG_WATCHDOG=y
 CONFIG_SL28CPLD_WATCHDOG=m
 CONFIG_ARM_SP805_WATCHDOG=y
 CONFIG_ARM_SBSA_WATCHDOG=y
-CONFIG_ARM_SMC_WATCHDOG=y
 CONFIG_S3C2410_WATCHDOG=y
 CONFIG_DW_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=m
@@ -601,6 +590,7 @@ CONFIG_IMX_SC_WDT=m
 CONFIG_QCOM_WDT=m
 CONFIG_MESON_GXBB_WATCHDOG=m
 CONFIG_MESON_WATCHDOG=m
+CONFIG_ARM_SMC_WATCHDOG=y
 CONFIG_RENESAS_WDT=y
 CONFIG_UNIPHIER_WATCHDOG=y
 CONFIG_BCM2835_WDT=y
@@ -653,13 +643,12 @@ CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
 CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
 CONFIG_MEDIA_SDR_SUPPORT=y
-CONFIG_MEDIA_CONTROLLER=y
-CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_MEDIA_PLATFORM_SUPPORT=y
 # CONFIG_DVB_NET is not set
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_QCOM_CAMSS=m
 CONFIG_VIDEO_RCAR_CSI2=m
 CONFIG_VIDEO_RCAR_VIN=m
 CONFIG_VIDEO_SUN6I_CSI=m
@@ -676,7 +665,6 @@ CONFIG_VIDEO_RCAR_DRIF=m
 CONFIG_VIDEO_IMX219=m
 CONFIG_VIDEO_OV5640=m
 CONFIG_VIDEO_OV5645=m
-CONFIG_VIDEO_QCOM_CAMSS=m
 CONFIG_DRM=m
 CONFIG_DRM_I2C_NXP_TDA998X=m
 CONFIG_DRM_MALI_DISPLAY=m
@@ -703,24 +691,24 @@ CONFIG_DRM_SUN8I_DW_HDMI=m
 CONFIG_DRM_SUN8I_MIXER=m
 CONFIG_DRM_MSM=m
 CONFIG_DRM_TEGRA=m
+CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
 CONFIG_DRM_PANEL_LVDS=m
 CONFIG_DRM_PANEL_SIMPLE=m
 CONFIG_DRM_PANEL_EDP=m
-CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
 CONFIG_DRM_PANEL_MANTIX_MLAF057WE51=m
 CONFIG_DRM_PANEL_RAYDIUM_RM67191=m
 CONFIG_DRM_PANEL_SITRONIX_ST7703=m
 CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA=m
 CONFIG_DRM_DISPLAY_CONNECTOR=m
 CONFIG_DRM_LONTIUM_LT8912B=m
-CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_LONTIUM_LT9611=m
+CONFIG_DRM_LONTIUM_LT9611UXC=m
+CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_PARADE_PS8640=m
 CONFIG_DRM_SII902X=m
 CONFIG_DRM_SIMPLE_BRIDGE=m
 CONFIG_DRM_THINE_THC63LVD1024=m
 CONFIG_DRM_TI_SN65DSI86=m
-CONFIG_DRM_LONTIUM_LT9611UXC=m
 CONFIG_DRM_I2C_ADV7511=m
 CONFIG_DRM_I2C_ADV7511_AUDIO=y
 CONFIG_DRM_DW_HDMI_AHB_AUDIO=m
@@ -751,15 +739,14 @@ CONFIG_SND_HDA_TEGRA=m
 CONFIG_SND_HDA_CODEC_HDMI=m
 CONFIG_SND_SOC=y
 CONFIG_SND_BCM2835_SOC_I2S=m
-CONFIG_SND_SOC_FSL_SAI=m
 CONFIG_SND_SOC_FSL_ASRC=m
 CONFIG_SND_SOC_FSL_MICFIL=m
 CONFIG_SND_SOC_FSL_EASRC=m
 CONFIG_SND_IMX_SOC=m
 CONFIG_SND_SOC_IMX_SGTL5000=m
 CONFIG_SND_SOC_IMX_SPDIF=m
-CONFIG_SND_SOC_IMX_AUDMIX=m
 CONFIG_SND_SOC_FSL_ASOC_CARD=m
+CONFIG_SND_SOC_IMX_AUDMIX=m
 CONFIG_SND_MESON_AXG_SOUND_CARD=m
 CONFIG_SND_MESON_GX_SOUND_CARD=m
 CONFIG_SND_SOC_QCOM=m
@@ -813,11 +800,9 @@ CONFIG_SND_AUDIO_GRAPH_CARD=m
 CONFIG_HID_MULTITOUCH=m
 CONFIG_I2C_HID_ACPI=m
 CONFIG_I2C_HID_OF=m
-CONFIG_USB_CONN_GPIO=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_PCI=m
 CONFIG_USB_XHCI_PCI_RENESAS=m
 CONFIG_USB_XHCI_TEGRA=y
 CONFIG_USB_EHCI_HCD=y
@@ -864,8 +849,8 @@ CONFIG_TYPEC=m
 CONFIG_TYPEC_TCPM=m
 CONFIG_TYPEC_TCPCI=m
 CONFIG_TYPEC_FUSB302=m
-CONFIG_TYPEC_HD3SS3220=m
 CONFIG_TYPEC_TPS6598X=m
+CONFIG_TYPEC_HD3SS3220=m
 CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_ARMMMCI=y
@@ -963,7 +948,6 @@ CONFIG_VIRTIO_BALLOON=y
 CONFIG_VIRTIO_MMIO=y
 CONFIG_XEN_GNTDEV=y
 CONFIG_XEN_GRANT_DEV_ALLOC=y
-CONFIG_MFD_CROS_EC_DEV=y
 CONFIG_STAGING=y
 CONFIG_STAGING_MEDIA=y
 CONFIG_VIDEO_HANTRO=m
@@ -973,15 +957,14 @@ CONFIG_CROS_EC=y
 CONFIG_CROS_EC_I2C=y
 CONFIG_CROS_EC_SPI=y
 CONFIG_CROS_EC_CHARDEV=m
-CONFIG_COMMON_CLK_SCMI=y
 CONFIG_COMMON_CLK_RK808=y
+CONFIG_COMMON_CLK_SCMI=y
 CONFIG_COMMON_CLK_SCPI=y
 CONFIG_COMMON_CLK_CS2000_CP=y
 CONFIG_COMMON_CLK_FSL_SAI=y
 CONFIG_COMMON_CLK_S2MPS11=y
 CONFIG_COMMON_CLK_PWM=y
 CONFIG_COMMON_CLK_VC5=y
-CONFIG_COMMON_CLK_ZYNQMP=y
 CONFIG_COMMON_CLK_BD718XX=m
 CONFIG_CLK_RASPBERRYPI=m
 CONFIG_CLK_IMX8MM=y
@@ -997,8 +980,8 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y
 CONFIG_QCOM_CLK_APCC_MSM8996=y
 CONFIG_QCOM_CLK_SMD_RPM=y
 CONFIG_QCOM_CLK_RPMH=y
-CONFIG_IPQ_GCC_8074=y
 CONFIG_IPQ_GCC_6018=y
+CONFIG_IPQ_GCC_8074=y
 CONFIG_MSM_GCC_8916=y
 CONFIG_MSM_GCC_8994=y
 CONFIG_MSM_MMCC_8996=y
@@ -1007,16 +990,13 @@ CONFIG_QCS_GCC_404=y
 CONFIG_SC_GCC_7180=y
 CONFIG_SC_GCC_7280=y
 CONFIG_SDM_CAMCC_845=m
-CONFIG_SDM_GCC_845=y
 CONFIG_SDM_GPUCC_845=y
 CONFIG_SDM_VIDEOCC_845=y
 CONFIG_SDM_DISPCC_845=y
-CONFIG_SM_GCC_8150=y
-CONFIG_SM_GCC_8250=y
+CONFIG_SM_DISPCC_8250=y
 CONFIG_SM_GCC_8350=y
 CONFIG_SM_GPUCC_8150=y
 CONFIG_SM_GPUCC_8250=y
-CONFIG_SM_DISPCC_8250=y
 CONFIG_QCOM_HFPLL=y
 CONFIG_CLK_GFM_LPASS_SM8250=m
 CONFIG_CLK_RCAR_USB2_CLOCK_SEL=y
@@ -1050,9 +1030,11 @@ CONFIG_RASPBERRYPI_POWER=y
 CONFIG_FSL_DPAA=y
 CONFIG_FSL_MC_DPIO=y
 CONFIG_FSL_RCPM=y
+CONFIG_MTK_DEVAPC=m
 CONFIG_MTK_PMIC_WRAP=y
 CONFIG_QCOM_AOSS_QMP=y
 CONFIG_QCOM_COMMAND_DB=y
+CONFIG_QCOM_CPR=y
 CONFIG_QCOM_GENI_SE=y
 CONFIG_QCOM_RMTFS_MEM=m
 CONFIG_QCOM_RPMH=y
@@ -1063,24 +1045,25 @@ CONFIG_QCOM_SMD_RPM=y
 CONFIG_QCOM_SMP2P=y
 CONFIG_QCOM_SMSM=y
 CONFIG_QCOM_SOCINFO=m
-CONFIG_QCOM_WCNSS_CTRL=m
 CONFIG_QCOM_STATS=m
+CONFIG_QCOM_WCNSS_CTRL=m
 CONFIG_QCOM_APR=m
-CONFIG_ARCH_R8A774A1=y
-CONFIG_ARCH_R8A774B1=y
-CONFIG_ARCH_R8A774C0=y
-CONFIG_ARCH_R8A774E1=y
+CONFIG_ARCH_R8A77995=y
+CONFIG_ARCH_R8A77990=y
 CONFIG_ARCH_R8A77950=y
 CONFIG_ARCH_R8A77951=y
+CONFIG_ARCH_R8A77965=y
 CONFIG_ARCH_R8A77960=y
 CONFIG_ARCH_R8A77961=y
-CONFIG_ARCH_R8A77965=y
-CONFIG_ARCH_R8A77970=y
 CONFIG_ARCH_R8A77980=y
-CONFIG_ARCH_R8A77990=y
-CONFIG_ARCH_R8A77995=y
+CONFIG_ARCH_R8A77970=y
 CONFIG_ARCH_R8A779A0=y
+CONFIG_ARCH_R8A774C0=y
+CONFIG_ARCH_R8A774E1=y
+CONFIG_ARCH_R8A774A1=y
+CONFIG_ARCH_R8A774B1=y
 CONFIG_ARCH_R9A07G044=y
+CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_ROCKCHIP_PM_DOMAINS=y
 CONFIG_ARCH_TEGRA_132_SOC=y
 CONFIG_ARCH_TEGRA_210_SOC=y
@@ -1159,13 +1142,13 @@ CONFIG_PHY_UNIPHIER_USB3=y
 CONFIG_PHY_TEGRA_XUSB=y
 CONFIG_ARM_SMMU_V3_PMU=m
 CONFIG_FSL_IMX8_DDR_PMU=m
-CONFIG_HISI_PMU=y
 CONFIG_QCOM_L2_PMU=y
 CONFIG_QCOM_L3_PMU=y
+CONFIG_HISI_PMU=y
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_NVMEM_IMX_OCOTP_SCU=y
-CONFIG_QCOM_QFPROM=y
 CONFIG_MTK_EFUSE=y
+CONFIG_QCOM_QFPROM=y
 CONFIG_ROCKCHIP_EFUSE=y
 CONFIG_NVMEM_SUNXI_SID=y
 CONFIG_UNIPHIER_EFUSE=y
@@ -1179,11 +1162,9 @@ CONFIG_FPGA_REGION=m
 CONFIG_OF_FPGA_REGION=m
 CONFIG_TEE=y
 CONFIG_OPTEE=y
-CONFIG_SLIMBUS=m
+CONFIG_MUX_MMIO=y
 CONFIG_SLIM_QCOM_CTRL=m
 CONFIG_SLIM_QCOM_NGD_CTRL=m
-CONFIG_MUX_MMIO=y
-CONFIG_INTERCONNECT=y
 CONFIG_INTERCONNECT_IMX=m
 CONFIG_INTERCONNECT_IMX8MM=m
 CONFIG_INTERCONNECT_IMX8MN=m
@@ -1211,7 +1192,6 @@ CONFIG_OVERLAY_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_HUGETLBFS=y
-CONFIG_CONFIGFS_FS=y
 CONFIG_EFIVAR_FS=y
 CONFIG_SQUASHFS=y
 CONFIG_NFS_FS=y
-- 
2.33.1

[PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Run "make defconfig; make savedefconfig" to rebuild defconfig.

This re-ordered the following configuration options:

CONFIG_BPF_JIT=y
CONFIG_ARM_SCMI_PROTOCOL=y
CONFIG_ARM_SCPI_PROTOCOL=y
CONFIG_RASPBERRYPI_FIRMWARE=y
CONFIG_INTEL_STRATIX10_SERVICE=y
CONFIG_INTEL_STRATIX10_RSU=m
CONFIG_EFI_CAPSULE_LOADER=y
CONFIG_IMX_SCU=y
CONFIG_IMX_SCU_PD=y
CONFIG_CAN_FLEXCAN=m
CONFIG_PCIE_LAYERSCAPE_GEN4=y
CONFIG_MTK_DEVAPC=m
CONFIG_SPI_CADENCE_QUADSPI=y
CONFIG_MDIO_BUS_MUX_MMIOREG=y
CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
CONFIG_MESON_GXL_PHY=m
CONFIG_QCOM_CPR=y
CONFIG_ROCKCHIP_IODOMAIN=y
CONFIG_SENSORS_ARM_SCMI=y
CONFIG_QORIQ_THERMAL=m
CONFIG_SUN8I_THERMAL=y
CONFIG_TEGRA_BPMP_THERMAL=m
CONFIG_ARM_SMC_WATCHDOG=y
CONFIG_VIDEO_QCOM_CAMSS=m
CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
CONFIG_DRM_NWL_MIPI_DSI=m
CONFIG_DRM_LONTIUM_LT9611UXC=m
CONFIG_SND_SOC_IMX_AUDMIX=m
CONFIG_TYPEC_HD3SS3220=m
CONFIG_COMMON_CLK_SCMI=y
CONFIG_IPQ_GCC_8074=y
CONFIG_SM_DISPCC_8250=y
CONFIG_QCOM_WCNSS_CTRL=m
CONFIG_ARCH_R8A774A1=y
CONFIG_ARCH_R8A774B1=y
CONFIG_ARCH_R8A774C0=y
CONFIG_ARCH_R8A774E1=y
CONFIG_ARCH_R8A77995=y
CONFIG_ARCH_R8A77990=y
CONFIG_ARCH_R8A77965=y
CONFIG_ARCH_R8A77970=y
CONFIG_HISI_PMU=y
CONFIG_QCOM_QFPROM=y
CONFIG_MUX_MMIO=y

And dropped the following configuration options which are nowaday's
already enabled (resp. disabled) by default:

CONFIG_MEMCG_SWAP=y
CONFIG_SECCOMP=y
CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
CONFIG_QCOM_SCM=y
# CONFIG_BT_HS is not set
CONFIG_FSL_MC_BUS=y
CONFIG_MEDIA_CONTROLLER=y
CONFIG_VIDEO_V4L2_SUBDEV_API=y
CONFIG_SND_SOC_FSL_SAI=m
CONFIG_USB_CONN_GPIO=m
CONFIG_USB_XHCI_PCI=m
CONFIG_MFD_CROS_EC_DEV=y
CONFIG_COMMON_CLK_ZYNQMP=y
CONFIG_SDM_GCC_845=y
CONFIG_SM_GCC_8150=y
CONFIG_SM_GCC_8250=y
CONFIG_SLIMBUS=m
CONFIG_INTERCONNECT=y
CONFIG_CONFIGFS_FS=y

CONFIG_POWER_AVS was renamed to POWER_AVS_OMAP in commit bca815d62054
("PM: AVS: smartreflex Move driver to soc specific drivers"). As there
are no 64-bit Arm OMAPs it getting dropped seems fair.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Done full defconfig analysis as requested by Krzysztof.

 arch/arm64/configs/defconfig | 108 ++++++++++++++---------------------
 1 file changed, 44 insertions(+), 64 deletions(-)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 7daf2de6c31a..bc39559c1658 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -3,6 +3,7 @@ CONFIG_POSIX_MQUEUE=y
 CONFIG_AUDIT=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BPF_JIT=y
 CONFIG_PREEMPT=y
 CONFIG_IRQ_TIME_ACCOUNTING=y
 CONFIG_BSD_PROCESS_ACCT=y
@@ -14,7 +15,6 @@ CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_NUMA_BALANCING=y
 CONFIG_MEMCG=y
-CONFIG_MEMCG_SWAP=y
 CONFIG_BLK_CGROUP=y
 CONFIG_CGROUP_PIDS=y
 CONFIG_CGROUP_HUGETLB=y
@@ -67,7 +67,6 @@ CONFIG_ARM64_VA_BITS_48=y
 CONFIG_SCHED_MC=y
 CONFIG_SCHED_SMT=y
 CONFIG_NUMA=y
-CONFIG_SECCOMP=y
 CONFIG_KEXEC=y
 CONFIG_KEXEC_FILE=y
 CONFIG_CRASH_DUMP=y
@@ -85,7 +84,6 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
 CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
-CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
 CONFIG_CPUFREQ_DT=y
 CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_ARM_ALLWINNER_SUN50I_CPUFREQ_NVMEM=m
@@ -98,15 +96,6 @@ CONFIG_ARM_RASPBERRYPI_CPUFREQ=m
 CONFIG_ARM_SCMI_CPUFREQ=y
 CONFIG_ARM_TEGRA186_CPUFREQ=y
 CONFIG_QORIQ_CPUFREQ=y
-CONFIG_ARM_SCMI_PROTOCOL=y
-CONFIG_ARM_SCPI_PROTOCOL=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_INTEL_STRATIX10_SERVICE=y
-CONFIG_INTEL_STRATIX10_RSU=m
-CONFIG_QCOM_SCM=y
-CONFIG_EFI_CAPSULE_LOADER=y
-CONFIG_IMX_SCU=y
-CONFIG_IMX_SCU_PD=y
 CONFIG_ACPI=y
 CONFIG_ACPI_APEI=y
 CONFIG_ACPI_APEI_GHES=y
@@ -183,14 +172,12 @@ CONFIG_NET_ACT_GATE=m
 CONFIG_QRTR=m
 CONFIG_QRTR_SMD=m
 CONFIG_QRTR_TUN=m
-CONFIG_BPF_JIT=y
 CONFIG_CAN=m
+CONFIG_CAN_FLEXCAN=m
 CONFIG_CAN_RCAR=m
 CONFIG_CAN_RCAR_CANFD=m
-CONFIG_CAN_FLEXCAN=m
 CONFIG_BT=m
 CONFIG_BT_HIDP=m
-# CONFIG_BT_HS is not set
 # CONFIG_BT_LE is not set
 CONFIG_BT_LEDS=y
 # CONFIG_BT_DEBUGFS is not set
@@ -230,7 +217,6 @@ CONFIG_PCIE_ROCKCHIP_HOST=m
 CONFIG_PCIE_BRCMSTB=m
 CONFIG_PCI_IMX6=y
 CONFIG_PCI_LAYERSCAPE=y
-CONFIG_PCIE_LAYERSCAPE_GEN4=y
 CONFIG_PCI_HISI=y
 CONFIG_PCIE_QCOM=y
 CONFIG_PCIE_ARMADA_8K=y
@@ -238,6 +224,7 @@ CONFIG_PCIE_KIRIN=y
 CONFIG_PCIE_HISI_STB=y
 CONFIG_PCIE_TEGRA194_HOST=m
 CONFIG_PCIE_VISCONTI_HOST=y
+CONFIG_PCIE_LAYERSCAPE_GEN4=y
 CONFIG_PCI_ENDPOINT=y
 CONFIG_PCI_ENDPOINT_CONFIGFS=y
 CONFIG_PCI_EPF_TEST=m
@@ -245,8 +232,15 @@ CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_FW_LOADER_USER_HELPER=y
 CONFIG_HISILICON_LPC=y
-CONFIG_FSL_MC_BUS=y
 CONFIG_TEGRA_ACONNECT=m
+CONFIG_ARM_SCMI_PROTOCOL=y
+CONFIG_ARM_SCPI_PROTOCOL=y
+CONFIG_RASPBERRYPI_FIRMWARE=y
+CONFIG_INTEL_STRATIX10_SERVICE=y
+CONFIG_INTEL_STRATIX10_RSU=m
+CONFIG_EFI_CAPSULE_LOADER=y
+CONFIG_IMX_SCU=y
+CONFIG_IMX_SCU_PD=y
 CONFIG_GNSS=m
 CONFIG_GNSS_MTK_SERIAL=m
 CONFIG_MTD=y
@@ -266,8 +260,6 @@ CONFIG_MTD_NAND_MARVELL=y
 CONFIG_MTD_NAND_FSL_IFC=y
 CONFIG_MTD_NAND_QCOM=y
 CONFIG_MTD_SPI_NOR=y
-CONFIG_MTK_DEVAPC=m
-CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=m
 CONFIG_VIRTIO_BLK=y
@@ -353,13 +345,11 @@ CONFIG_SNI_NETSEC=y
 CONFIG_STMMAC_ETH=m
 CONFIG_TI_K3_AM65_CPSW_NUSS=y
 CONFIG_QCOM_IPA=m
-CONFIG_MDIO_BUS_MUX_MMIOREG=y
-CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
+CONFIG_MESON_GXL_PHY=m
 CONFIG_AQUANTIA_PHY=y
 CONFIG_BCM54140_PHY=m
 CONFIG_MARVELL_PHY=m
 CONFIG_MARVELL_10G_PHY=m
-CONFIG_MESON_GXL_PHY=m
 CONFIG_MICREL_PHY=y
 CONFIG_MICROSEMI_PHY=y
 CONFIG_AT803X_PHY=y
@@ -367,6 +357,8 @@ CONFIG_REALTEK_PHY=y
 CONFIG_ROCKCHIP_PHY=y
 CONFIG_DP83867_PHY=y
 CONFIG_VITESSE_PHY=y
+CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
+CONFIG_MDIO_BUS_MUX_MMIOREG=y
 CONFIG_USB_PEGASUS=m
 CONFIG_USB_RTL8150=m
 CONFIG_USB_RTL8152=m
@@ -474,6 +466,7 @@ CONFIG_SPI=y
 CONFIG_SPI_ARMADA_3700=y
 CONFIG_SPI_BCM2835=m
 CONFIG_SPI_BCM2835AUX=m
+CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_SPI_DESIGNWARE=m
 CONFIG_SPI_DW_DMA=y
 CONFIG_SPI_DW_MMIO=m
@@ -545,9 +538,6 @@ CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_BD9571MWV=m
 CONFIG_GPIO_MAX77620=y
 CONFIG_GPIO_SL28CPLD=m
-CONFIG_POWER_AVS=y
-CONFIG_QCOM_CPR=y
-CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_POWER_RESET_MSM=y
 CONFIG_POWER_RESET_QCOM_PON=m
 CONFIG_POWER_RESET_XGENE=y
@@ -555,10 +545,10 @@ CONFIG_POWER_RESET_SYSCON=y
 CONFIG_SYSCON_REBOOT_MODE=y
 CONFIG_BATTERY_SBS=m
 CONFIG_BATTERY_BQ27XXX=y
-CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_BATTERY_MAX17042=m
 CONFIG_CHARGER_BQ25890=m
 CONFIG_CHARGER_BQ25980=m
+CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_SENSORS_ARM_SCPI=y
 CONFIG_SENSORS_JC42=m
 CONFIG_SENSORS_LM90=m
@@ -570,10 +560,10 @@ CONFIG_SENSORS_INA3221=m
 CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
 CONFIG_THERMAL_EMULATION=y
-CONFIG_QORIQ_THERMAL=m
-CONFIG_SUN8I_THERMAL=y
 CONFIG_IMX_SC_THERMAL=m
 CONFIG_IMX8MM_THERMAL=m
+CONFIG_QORIQ_THERMAL=m
+CONFIG_SUN8I_THERMAL=y
 CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_RCAR_THERMAL=y
 CONFIG_RCAR_GEN3_THERMAL=y
@@ -582,8 +572,8 @@ CONFIG_BCM2711_THERMAL=m
 CONFIG_BCM2835_THERMAL=m
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_EXYNOS_THERMAL=y
-CONFIG_TEGRA_BPMP_THERMAL=m
 CONFIG_TEGRA_SOCTHERM=m
+CONFIG_TEGRA_BPMP_THERMAL=m
 CONFIG_QCOM_TSENS=y
 CONFIG_QCOM_SPMI_TEMP_ALARM=m
 CONFIG_QCOM_LMH=m
@@ -592,7 +582,6 @@ CONFIG_WATCHDOG=y
 CONFIG_SL28CPLD_WATCHDOG=m
 CONFIG_ARM_SP805_WATCHDOG=y
 CONFIG_ARM_SBSA_WATCHDOG=y
-CONFIG_ARM_SMC_WATCHDOG=y
 CONFIG_S3C2410_WATCHDOG=y
 CONFIG_DW_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=m
@@ -601,6 +590,7 @@ CONFIG_IMX_SC_WDT=m
 CONFIG_QCOM_WDT=m
 CONFIG_MESON_GXBB_WATCHDOG=m
 CONFIG_MESON_WATCHDOG=m
+CONFIG_ARM_SMC_WATCHDOG=y
 CONFIG_RENESAS_WDT=y
 CONFIG_UNIPHIER_WATCHDOG=y
 CONFIG_BCM2835_WDT=y
@@ -653,13 +643,12 @@ CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
 CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
 CONFIG_MEDIA_SDR_SUPPORT=y
-CONFIG_MEDIA_CONTROLLER=y
-CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_MEDIA_PLATFORM_SUPPORT=y
 # CONFIG_DVB_NET is not set
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_QCOM_CAMSS=m
 CONFIG_VIDEO_RCAR_CSI2=m
 CONFIG_VIDEO_RCAR_VIN=m
 CONFIG_VIDEO_SUN6I_CSI=m
@@ -676,7 +665,6 @@ CONFIG_VIDEO_RCAR_DRIF=m
 CONFIG_VIDEO_IMX219=m
 CONFIG_VIDEO_OV5640=m
 CONFIG_VIDEO_OV5645=m
-CONFIG_VIDEO_QCOM_CAMSS=m
 CONFIG_DRM=m
 CONFIG_DRM_I2C_NXP_TDA998X=m
 CONFIG_DRM_MALI_DISPLAY=m
@@ -703,24 +691,24 @@ CONFIG_DRM_SUN8I_DW_HDMI=m
 CONFIG_DRM_SUN8I_MIXER=m
 CONFIG_DRM_MSM=m
 CONFIG_DRM_TEGRA=m
+CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
 CONFIG_DRM_PANEL_LVDS=m
 CONFIG_DRM_PANEL_SIMPLE=m
 CONFIG_DRM_PANEL_EDP=m
-CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
 CONFIG_DRM_PANEL_MANTIX_MLAF057WE51=m
 CONFIG_DRM_PANEL_RAYDIUM_RM67191=m
 CONFIG_DRM_PANEL_SITRONIX_ST7703=m
 CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA=m
 CONFIG_DRM_DISPLAY_CONNECTOR=m
 CONFIG_DRM_LONTIUM_LT8912B=m
-CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_LONTIUM_LT9611=m
+CONFIG_DRM_LONTIUM_LT9611UXC=m
+CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_PARADE_PS8640=m
 CONFIG_DRM_SII902X=m
 CONFIG_DRM_SIMPLE_BRIDGE=m
 CONFIG_DRM_THINE_THC63LVD1024=m
 CONFIG_DRM_TI_SN65DSI86=m
-CONFIG_DRM_LONTIUM_LT9611UXC=m
 CONFIG_DRM_I2C_ADV7511=m
 CONFIG_DRM_I2C_ADV7511_AUDIO=y
 CONFIG_DRM_DW_HDMI_AHB_AUDIO=m
@@ -751,15 +739,14 @@ CONFIG_SND_HDA_TEGRA=m
 CONFIG_SND_HDA_CODEC_HDMI=m
 CONFIG_SND_SOC=y
 CONFIG_SND_BCM2835_SOC_I2S=m
-CONFIG_SND_SOC_FSL_SAI=m
 CONFIG_SND_SOC_FSL_ASRC=m
 CONFIG_SND_SOC_FSL_MICFIL=m
 CONFIG_SND_SOC_FSL_EASRC=m
 CONFIG_SND_IMX_SOC=m
 CONFIG_SND_SOC_IMX_SGTL5000=m
 CONFIG_SND_SOC_IMX_SPDIF=m
-CONFIG_SND_SOC_IMX_AUDMIX=m
 CONFIG_SND_SOC_FSL_ASOC_CARD=m
+CONFIG_SND_SOC_IMX_AUDMIX=m
 CONFIG_SND_MESON_AXG_SOUND_CARD=m
 CONFIG_SND_MESON_GX_SOUND_CARD=m
 CONFIG_SND_SOC_QCOM=m
@@ -813,11 +800,9 @@ CONFIG_SND_AUDIO_GRAPH_CARD=m
 CONFIG_HID_MULTITOUCH=m
 CONFIG_I2C_HID_ACPI=m
 CONFIG_I2C_HID_OF=m
-CONFIG_USB_CONN_GPIO=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_PCI=m
 CONFIG_USB_XHCI_PCI_RENESAS=m
 CONFIG_USB_XHCI_TEGRA=y
 CONFIG_USB_EHCI_HCD=y
@@ -864,8 +849,8 @@ CONFIG_TYPEC=m
 CONFIG_TYPEC_TCPM=m
 CONFIG_TYPEC_TCPCI=m
 CONFIG_TYPEC_FUSB302=m
-CONFIG_TYPEC_HD3SS3220=m
 CONFIG_TYPEC_TPS6598X=m
+CONFIG_TYPEC_HD3SS3220=m
 CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_ARMMMCI=y
@@ -963,7 +948,6 @@ CONFIG_VIRTIO_BALLOON=y
 CONFIG_VIRTIO_MMIO=y
 CONFIG_XEN_GNTDEV=y
 CONFIG_XEN_GRANT_DEV_ALLOC=y
-CONFIG_MFD_CROS_EC_DEV=y
 CONFIG_STAGING=y
 CONFIG_STAGING_MEDIA=y
 CONFIG_VIDEO_HANTRO=m
@@ -973,15 +957,14 @@ CONFIG_CROS_EC=y
 CONFIG_CROS_EC_I2C=y
 CONFIG_CROS_EC_SPI=y
 CONFIG_CROS_EC_CHARDEV=m
-CONFIG_COMMON_CLK_SCMI=y
 CONFIG_COMMON_CLK_RK808=y
+CONFIG_COMMON_CLK_SCMI=y
 CONFIG_COMMON_CLK_SCPI=y
 CONFIG_COMMON_CLK_CS2000_CP=y
 CONFIG_COMMON_CLK_FSL_SAI=y
 CONFIG_COMMON_CLK_S2MPS11=y
 CONFIG_COMMON_CLK_PWM=y
 CONFIG_COMMON_CLK_VC5=y
-CONFIG_COMMON_CLK_ZYNQMP=y
 CONFIG_COMMON_CLK_BD718XX=m
 CONFIG_CLK_RASPBERRYPI=m
 CONFIG_CLK_IMX8MM=y
@@ -997,8 +980,8 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y
 CONFIG_QCOM_CLK_APCC_MSM8996=y
 CONFIG_QCOM_CLK_SMD_RPM=y
 CONFIG_QCOM_CLK_RPMH=y
-CONFIG_IPQ_GCC_8074=y
 CONFIG_IPQ_GCC_6018=y
+CONFIG_IPQ_GCC_8074=y
 CONFIG_MSM_GCC_8916=y
 CONFIG_MSM_GCC_8994=y
 CONFIG_MSM_MMCC_8996=y
@@ -1007,16 +990,13 @@ CONFIG_QCS_GCC_404=y
 CONFIG_SC_GCC_7180=y
 CONFIG_SC_GCC_7280=y
 CONFIG_SDM_CAMCC_845=m
-CONFIG_SDM_GCC_845=y
 CONFIG_SDM_GPUCC_845=y
 CONFIG_SDM_VIDEOCC_845=y
 CONFIG_SDM_DISPCC_845=y
-CONFIG_SM_GCC_8150=y
-CONFIG_SM_GCC_8250=y
+CONFIG_SM_DISPCC_8250=y
 CONFIG_SM_GCC_8350=y
 CONFIG_SM_GPUCC_8150=y
 CONFIG_SM_GPUCC_8250=y
-CONFIG_SM_DISPCC_8250=y
 CONFIG_QCOM_HFPLL=y
 CONFIG_CLK_GFM_LPASS_SM8250=m
 CONFIG_CLK_RCAR_USB2_CLOCK_SEL=y
@@ -1050,9 +1030,11 @@ CONFIG_RASPBERRYPI_POWER=y
 CONFIG_FSL_DPAA=y
 CONFIG_FSL_MC_DPIO=y
 CONFIG_FSL_RCPM=y
+CONFIG_MTK_DEVAPC=m
 CONFIG_MTK_PMIC_WRAP=y
 CONFIG_QCOM_AOSS_QMP=y
 CONFIG_QCOM_COMMAND_DB=y
+CONFIG_QCOM_CPR=y
 CONFIG_QCOM_GENI_SE=y
 CONFIG_QCOM_RMTFS_MEM=m
 CONFIG_QCOM_RPMH=y
@@ -1063,24 +1045,25 @@ CONFIG_QCOM_SMD_RPM=y
 CONFIG_QCOM_SMP2P=y
 CONFIG_QCOM_SMSM=y
 CONFIG_QCOM_SOCINFO=m
-CONFIG_QCOM_WCNSS_CTRL=m
 CONFIG_QCOM_STATS=m
+CONFIG_QCOM_WCNSS_CTRL=m
 CONFIG_QCOM_APR=m
-CONFIG_ARCH_R8A774A1=y
-CONFIG_ARCH_R8A774B1=y
-CONFIG_ARCH_R8A774C0=y
-CONFIG_ARCH_R8A774E1=y
+CONFIG_ARCH_R8A77995=y
+CONFIG_ARCH_R8A77990=y
 CONFIG_ARCH_R8A77950=y
 CONFIG_ARCH_R8A77951=y
+CONFIG_ARCH_R8A77965=y
 CONFIG_ARCH_R8A77960=y
 CONFIG_ARCH_R8A77961=y
-CONFIG_ARCH_R8A77965=y
-CONFIG_ARCH_R8A77970=y
 CONFIG_ARCH_R8A77980=y
-CONFIG_ARCH_R8A77990=y
-CONFIG_ARCH_R8A77995=y
+CONFIG_ARCH_R8A77970=y
 CONFIG_ARCH_R8A779A0=y
+CONFIG_ARCH_R8A774C0=y
+CONFIG_ARCH_R8A774E1=y
+CONFIG_ARCH_R8A774A1=y
+CONFIG_ARCH_R8A774B1=y
 CONFIG_ARCH_R9A07G044=y
+CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_ROCKCHIP_PM_DOMAINS=y
 CONFIG_ARCH_TEGRA_132_SOC=y
 CONFIG_ARCH_TEGRA_210_SOC=y
@@ -1159,13 +1142,13 @@ CONFIG_PHY_UNIPHIER_USB3=y
 CONFIG_PHY_TEGRA_XUSB=y
 CONFIG_ARM_SMMU_V3_PMU=m
 CONFIG_FSL_IMX8_DDR_PMU=m
-CONFIG_HISI_PMU=y
 CONFIG_QCOM_L2_PMU=y
 CONFIG_QCOM_L3_PMU=y
+CONFIG_HISI_PMU=y
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_NVMEM_IMX_OCOTP_SCU=y
-CONFIG_QCOM_QFPROM=y
 CONFIG_MTK_EFUSE=y
+CONFIG_QCOM_QFPROM=y
 CONFIG_ROCKCHIP_EFUSE=y
 CONFIG_NVMEM_SUNXI_SID=y
 CONFIG_UNIPHIER_EFUSE=y
@@ -1179,11 +1162,9 @@ CONFIG_FPGA_REGION=m
 CONFIG_OF_FPGA_REGION=m
 CONFIG_TEE=y
 CONFIG_OPTEE=y
-CONFIG_SLIMBUS=m
+CONFIG_MUX_MMIO=y
 CONFIG_SLIM_QCOM_CTRL=m
 CONFIG_SLIM_QCOM_NGD_CTRL=m
-CONFIG_MUX_MMIO=y
-CONFIG_INTERCONNECT=y
 CONFIG_INTERCONNECT_IMX=m
 CONFIG_INTERCONNECT_IMX8MM=m
 CONFIG_INTERCONNECT_IMX8MN=m
@@ -1211,7 +1192,6 @@ CONFIG_OVERLAY_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_HUGETLBFS=y
-CONFIG_CONFIGFS_FS=y
 CONFIG_EFIVAR_FS=y
 CONFIG_SQUASHFS=y
 CONFIG_NFS_FS=y
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 06/11] arm64: defconfig: enable bpf/cgroup firewalling

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This avoids the following systemd warning:

[    2.618538] systemd[1]: system-getty.slice: unit configures an IP
 firewall, but the local system does not support BPF/cgroup firewalling.
[    2.630916] systemd[1]: (This warning is only shown for the first
 unit using IP firewalling.)

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Song Liu <songliubraving@fb.com>

---

Changes in v2:
- Add Song's acked-by tag.

 arch/arm64/configs/defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index bc39559c1658..872b38613c6c 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -3,6 +3,7 @@ CONFIG_POSIX_MQUEUE=y
 CONFIG_AUDIT=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BPF_SYSCALL=y
 CONFIG_BPF_JIT=y
 CONFIG_PREEMPT=y
 CONFIG_IRQ_TIME_ACCOUNTING=y
@@ -22,6 +23,7 @@ CONFIG_CPUSETS=y
 CONFIG_CGROUP_DEVICE=y
 CONFIG_CGROUP_CPUACCT=y
 CONFIG_CGROUP_PERF=y
+CONFIG_CGROUP_BPF=y
 CONFIG_USER_NS=y
 CONFIG_SCHED_AUTOGROUP=y
 CONFIG_BLK_DEV_INITRD=y
-- 
2.33.1

[PATCH v2 06/11] arm64: defconfig: enable bpf/cgroup firewalling

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This avoids the following systemd warning:

[    2.618538] systemd[1]: system-getty.slice: unit configures an IP
 firewall, but the local system does not support BPF/cgroup firewalling.
[    2.630916] systemd[1]: (This warning is only shown for the first
 unit using IP firewalling.)

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Song Liu <songliubraving@fb.com>

---

Changes in v2:
- Add Song's acked-by tag.

 arch/arm64/configs/defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index bc39559c1658..872b38613c6c 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -3,6 +3,7 @@ CONFIG_POSIX_MQUEUE=y
 CONFIG_AUDIT=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BPF_SYSCALL=y
 CONFIG_BPF_JIT=y
 CONFIG_PREEMPT=y
 CONFIG_IRQ_TIME_ACCOUNTING=y
@@ -22,6 +23,7 @@ CONFIG_CPUSETS=y
 CONFIG_CGROUP_DEVICE=y
 CONFIG_CGROUP_CPUACCT=y
 CONFIG_CGROUP_PERF=y
+CONFIG_CGROUP_BPF=y
 CONFIG_USER_NS=y
 CONFIG_SCHED_AUTOGROUP=y
 CONFIG_BLK_DEV_INITRD=y
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 07/11] arm64: defconfig: build imx-sdma as a module

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This avoids firmware load error and sysfs fallback reported as follows:

[    0.199448] imx-sdma 302c0000.dma-controller: Direct firmware load
 for imx/sdma/sdma-imx7d.bin failed with error -2
[    0.199487] imx-sdma 302c0000.dma-controller: Falling back to sysfs
 fallback for: imx/sdma/sdma-imx7d.bin

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- A similar change got accepted for imx_v6_v7_defconfig. Further
discussion may be found in [1].
[1] https://lore.kernel.org/lkml/20210920144938.314588-6-marcel@ziswiler.com/

 arch/arm64/configs/defconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 872b38613c6c..3d200a149a88 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -927,7 +927,7 @@ CONFIG_DMADEVICES=y
 CONFIG_DMA_BCM2835=y
 CONFIG_DMA_SUN6I=m
 CONFIG_FSL_EDMA=y
-CONFIG_IMX_SDMA=y
+CONFIG_IMX_SDMA=m
 CONFIG_K3_DMA=y
 CONFIG_MV_XOR=y
 CONFIG_MV_XOR_V2=y
-- 
2.33.1

[PATCH v2 07/11] arm64: defconfig: build imx-sdma as a module

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This avoids firmware load error and sysfs fallback reported as follows:

[    0.199448] imx-sdma 302c0000.dma-controller: Direct firmware load
 for imx/sdma/sdma-imx7d.bin failed with error -2
[    0.199487] imx-sdma 302c0000.dma-controller: Falling back to sysfs
 fallback for: imx/sdma/sdma-imx7d.bin

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- A similar change got accepted for imx_v6_v7_defconfig. Further
discussion may be found in [1].
[1] https://lore.kernel.org/lkml/20210920144938.314588-6-marcel@ziswiler.com/

 arch/arm64/configs/defconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 872b38613c6c..3d200a149a88 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -927,7 +927,7 @@ CONFIG_DMADEVICES=y
 CONFIG_DMA_BCM2835=y
 CONFIG_DMA_SUN6I=m
 CONFIG_FSL_EDMA=y
-CONFIG_IMX_SDMA=y
+CONFIG_IMX_SDMA=m
 CONFIG_K3_DMA=y
 CONFIG_MV_XOR=y
 CONFIG_MV_XOR_V2=y
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 08/11] arm64: defconfig: build r8169 as a module

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Build Realtek Gigabit Ethernet driver as a module.

Network cards based on chipsets this driver supports are ubiquitous both
in regular PCIe as well as mini-PCIe and nowadays even various M.2
formats. It is therefore a suitable card to be used for any kind of PCIe
and/or Gigabit Ethernet testing. As it is not designed in, just enabling
it as a module seems most suitable.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Explain why enabling it may be a good idea as requested by Krzysztof.

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 3d200a149a88..f80d7fb53b7e 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -338,6 +338,7 @@ CONFIG_MLX5_CORE=m
 CONFIG_MLX5_CORE_EN=y
 CONFIG_QCOM_EMAC=m
 CONFIG_RMNET=m
+CONFIG_R8169=m
 CONFIG_SH_ETH=y
 CONFIG_RAVB=y
 CONFIG_SMC91X=y
-- 
2.33.1

[PATCH v2 08/11] arm64: defconfig: build r8169 as a module

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Build Realtek Gigabit Ethernet driver as a module.

Network cards based on chipsets this driver supports are ubiquitous both
in regular PCIe as well as mini-PCIe and nowadays even various M.2
formats. It is therefore a suitable card to be used for any kind of PCIe
and/or Gigabit Ethernet testing. As it is not designed in, just enabling
it as a module seems most suitable.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Explain why enabling it may be a good idea as requested by Krzysztof.

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 3d200a149a88..f80d7fb53b7e 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -338,6 +338,7 @@ CONFIG_MLX5_CORE=m
 CONFIG_MLX5_CORE_EN=y
 CONFIG_QCOM_EMAC=m
 CONFIG_RMNET=m
+CONFIG_R8169=m
 CONFIG_SH_ETH=y
 CONFIG_RAVB=y
 CONFIG_SMC91X=y
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 09/11] arm64: defconfig: enable verdin-imx8mm relevant drivers as modules

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Enable various drivers which support peripherals as found on the
Verdin iMX8M Mini et al. computer/system on modules:

- CONFIG_CAN_MCP251XFD
At least one Microchip MCP2518FDT SPI CAN controller which this driver
also supports may be found on the Verdin iMX8M Mini computer/system on
module.

- CONFIG_BT_HCIUART_MRVL, CONFIG_BT_MRVL, CONFIG_BT_MRVL_SDIO and
  CONFIG_MWIFIEX_SDIO
The AzureWave AW-CM276NF which these Bluetooth and Wi-Fi drivers also
support may be found on the Verdin iMX8M Mini (as well as the Apalis
iMX8, Colibri iMX8X and Verdin iMX8M Plus for that matter) computer/
system on module.

- CONFIG_SENSORS_LM75
The TI TMP75C temperature sensor which this driver also supports may be
found on the Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for
that matter) computer/system on module.

- CONFIG_SND_SOC_NAU8822
The Nuvoton Technology Corporation (NTC) NAU88C22YG which this driver
also supports may be found on the Verdin Development Board a carrier
board for the Verdin family of computer/system on module which the
Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
may be mated in.

- CONFIG_TI_ADS1015
The TLA2024 ADC which this driver also supports may be found on the
Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
computer/system on module.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Explain why enabling these may make sense and squash them relevant
  changes as requested by Krzysztof.

 arch/arm64/configs/defconfig | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index f80d7fb53b7e..6f4507b30916 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -178,6 +178,7 @@ CONFIG_CAN=m
 CONFIG_CAN_FLEXCAN=m
 CONFIG_CAN_RCAR=m
 CONFIG_CAN_RCAR_CANFD=m
+CONFIG_CAN_MCP251XFD=m
 CONFIG_BT=m
 CONFIG_BT_HIDP=m
 # CONFIG_BT_LE is not set
@@ -188,6 +189,9 @@ CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_LL=y
 CONFIG_BT_HCIUART_BCM=y
 CONFIG_BT_HCIUART_QCA=y
+CONFIG_BT_HCIUART_MRVL=y
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
 CONFIG_BT_QCOMSMD=m
 CONFIG_CFG80211=m
 CONFIG_MAC80211=m
@@ -379,6 +383,7 @@ CONFIG_ATH10K_SNOC=m
 CONFIG_WCN36XX=m
 CONFIG_BRCMFMAC=m
 CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
 CONFIG_MWIFIEX_PCIE=m
 CONFIG_WL18XX=m
 CONFIG_WLCORE_SDIO=m
@@ -554,6 +559,7 @@ CONFIG_CHARGER_BQ25980=m
 CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_SENSORS_ARM_SCPI=y
 CONFIG_SENSORS_JC42=m
+CONFIG_SENSORS_LM75=m
 CONFIG_SENSORS_LM90=m
 CONFIG_SENSORS_PWM_FAN=m
 CONFIG_SENSORS_RASPBERRYPI_HWMON=m
@@ -796,6 +802,7 @@ CONFIG_SND_SOC_WM8960=m
 CONFIG_SND_SOC_WM8962=m
 CONFIG_SND_SOC_WM8978=m
 CONFIG_SND_SOC_WSA881X=m
+CONFIG_SND_SOC_NAU8822=m
 CONFIG_SND_SOC_LPASS_WSA_MACRO=m
 CONFIG_SND_SOC_LPASS_VA_MACRO=m
 CONFIG_SND_SIMPLE_CARD=m
@@ -1087,6 +1094,7 @@ CONFIG_QCOM_SPMI_VADC=m
 CONFIG_QCOM_SPMI_ADC5=m
 CONFIG_ROCKCHIP_SARADC=m
 CONFIG_RZG2L_ADC=m
+CONFIG_TI_ADS1015=m
 CONFIG_IIO_CROS_EC_SENSORS_CORE=m
 CONFIG_IIO_CROS_EC_SENSORS=m
 CONFIG_IIO_ST_LSM6DSX=m
-- 
2.33.1

[PATCH v2 09/11] arm64: defconfig: enable verdin-imx8mm relevant drivers as modules

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Enable various drivers which support peripherals as found on the
Verdin iMX8M Mini et al. computer/system on modules:

- CONFIG_CAN_MCP251XFD
At least one Microchip MCP2518FDT SPI CAN controller which this driver
also supports may be found on the Verdin iMX8M Mini computer/system on
module.

- CONFIG_BT_HCIUART_MRVL, CONFIG_BT_MRVL, CONFIG_BT_MRVL_SDIO and
  CONFIG_MWIFIEX_SDIO
The AzureWave AW-CM276NF which these Bluetooth and Wi-Fi drivers also
support may be found on the Verdin iMX8M Mini (as well as the Apalis
iMX8, Colibri iMX8X and Verdin iMX8M Plus for that matter) computer/
system on module.

- CONFIG_SENSORS_LM75
The TI TMP75C temperature sensor which this driver also supports may be
found on the Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for
that matter) computer/system on module.

- CONFIG_SND_SOC_NAU8822
The Nuvoton Technology Corporation (NTC) NAU88C22YG which this driver
also supports may be found on the Verdin Development Board a carrier
board for the Verdin family of computer/system on module which the
Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
may be mated in.

- CONFIG_TI_ADS1015
The TLA2024 ADC which this driver also supports may be found on the
Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
computer/system on module.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Explain why enabling these may make sense and squash them relevant
  changes as requested by Krzysztof.

 arch/arm64/configs/defconfig | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index f80d7fb53b7e..6f4507b30916 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -178,6 +178,7 @@ CONFIG_CAN=m
 CONFIG_CAN_FLEXCAN=m
 CONFIG_CAN_RCAR=m
 CONFIG_CAN_RCAR_CANFD=m
+CONFIG_CAN_MCP251XFD=m
 CONFIG_BT=m
 CONFIG_BT_HIDP=m
 # CONFIG_BT_LE is not set
@@ -188,6 +189,9 @@ CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_LL=y
 CONFIG_BT_HCIUART_BCM=y
 CONFIG_BT_HCIUART_QCA=y
+CONFIG_BT_HCIUART_MRVL=y
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
 CONFIG_BT_QCOMSMD=m
 CONFIG_CFG80211=m
 CONFIG_MAC80211=m
@@ -379,6 +383,7 @@ CONFIG_ATH10K_SNOC=m
 CONFIG_WCN36XX=m
 CONFIG_BRCMFMAC=m
 CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
 CONFIG_MWIFIEX_PCIE=m
 CONFIG_WL18XX=m
 CONFIG_WLCORE_SDIO=m
@@ -554,6 +559,7 @@ CONFIG_CHARGER_BQ25980=m
 CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_SENSORS_ARM_SCPI=y
 CONFIG_SENSORS_JC42=m
+CONFIG_SENSORS_LM75=m
 CONFIG_SENSORS_LM90=m
 CONFIG_SENSORS_PWM_FAN=m
 CONFIG_SENSORS_RASPBERRYPI_HWMON=m
@@ -796,6 +802,7 @@ CONFIG_SND_SOC_WM8960=m
 CONFIG_SND_SOC_WM8962=m
 CONFIG_SND_SOC_WM8978=m
 CONFIG_SND_SOC_WSA881X=m
+CONFIG_SND_SOC_NAU8822=m
 CONFIG_SND_SOC_LPASS_WSA_MACRO=m
 CONFIG_SND_SOC_LPASS_VA_MACRO=m
 CONFIG_SND_SIMPLE_CARD=m
@@ -1087,6 +1094,7 @@ CONFIG_QCOM_SPMI_VADC=m
 CONFIG_QCOM_SPMI_ADC5=m
 CONFIG_ROCKCHIP_SARADC=m
 CONFIG_RZG2L_ADC=m
+CONFIG_TI_ADS1015=m
 CONFIG_IIO_CROS_EC_SENSORS_CORE=m
 CONFIG_IIO_CROS_EC_SENSORS=m
 CONFIG_IIO_ST_LSM6DSX=m
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 10/11] dt-bindings: arm: fsl: add toradex,verdin-imx8mm et al.

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Add toradex,verdin-imx8mm for our new Verdin iMX8M Mini modules, its
nonwifi and wifi variants and the carrier boards (both Dahlia and the
Verdin Development Board) they may be mated in.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>

---

Changes in v2:
- Add Rob's acked-by tag.
- Fix Colibri vs. Verdin copy/paste mistake. Thanks to Francesco Dolcini
  <francesco.dolcini@toradex.com> for pointing that out to me.

 .../devicetree/bindings/arm/fsl.yaml          | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 97f6eebad76a..7b7b6d3aa16f 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -770,6 +770,9 @@ properties:
               - gw,imx8mm-gw7901          # i.MX8MM Gateworks Board
               - gw,imx8mm-gw7902          # i.MX8MM Gateworks Board
               - kontron,imx8mm-n801x-som  # i.MX8MM Kontron SL (N801X) SOM
+              - toradex,verdin-imx8mm     # Verdin iMX8M Mini Modules
+              - toradex,verdin-imx8mm-nonwifi  # Verdin iMX8M Mini Modules without Wi-Fi / BT
+              - toradex,verdin-imx8mm-wifi  # Verdin iMX8M Mini Wi-Fi / BT Modules
               - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
 
@@ -787,6 +790,24 @@ properties:
           - const: kontron,imx8mm-n801x-som
           - const: fsl,imx8mm
 
+      - description: Toradex Boards with Verdin iMX8M Mini Modules
+        items:
+          - enum:
+              - toradex,verdin-imx8mm-nonwifi-dahlia # Verdin iMX8M Mini Module on Dahlia
+              - toradex,verdin-imx8mm-nonwifi-dev    # Verdin iMX8M Mini Module on Verdin Development Board
+          - const: toradex,verdin-imx8mm-nonwifi     # Verdin iMX8M Mini Module without Wi-Fi / BT
+          - const: toradex,verdin-imx8mm             # Verdin iMX8M Mini Module
+          - const: fsl,imx8mm
+
+      - description: Toradex Boards with Verdin iMX8M Mini Wi-Fi / BT Modules
+        items:
+          - enum:
+              - toradex,verdin-imx8mm-wifi-dahlia # Verdin iMX8M Mini Wi-Fi / BT Module on Dahlia
+              - toradex,verdin-imx8mm-wifi-dev    # Verdin iMX8M Mini Wi-Fi / BT M. on Verdin Development B.
+          - const: toradex,verdin-imx8mm-wifi     # Verdin iMX8M Mini Wi-Fi / BT Module
+          - const: toradex,verdin-imx8mm          # Verdin iMX8M Mini Module
+          - const: fsl,imx8mm
+
       - description: Variscite VAR-SOM-MX8MM based boards
         items:
           - const: variscite,var-som-mx8mm-symphony
-- 
2.33.1

[PATCH v2 10/11] dt-bindings: arm: fsl: add toradex, verdin-imx8mm et al.

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Add toradex,verdin-imx8mm for our new Verdin iMX8M Mini modules, its
nonwifi and wifi variants and the carrier boards (both Dahlia and the
Verdin Development Board) they may be mated in.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>

---

Changes in v2:
- Add Rob's acked-by tag.
- Fix Colibri vs. Verdin copy/paste mistake. Thanks to Francesco Dolcini
  <francesco.dolcini@toradex.com> for pointing that out to me.

 .../devicetree/bindings/arm/fsl.yaml          | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 97f6eebad76a..7b7b6d3aa16f 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -770,6 +770,9 @@ properties:
               - gw,imx8mm-gw7901          # i.MX8MM Gateworks Board
               - gw,imx8mm-gw7902          # i.MX8MM Gateworks Board
               - kontron,imx8mm-n801x-som  # i.MX8MM Kontron SL (N801X) SOM
+              - toradex,verdin-imx8mm     # Verdin iMX8M Mini Modules
+              - toradex,verdin-imx8mm-nonwifi  # Verdin iMX8M Mini Modules without Wi-Fi / BT
+              - toradex,verdin-imx8mm-wifi  # Verdin iMX8M Mini Wi-Fi / BT Modules
               - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
 
@@ -787,6 +790,24 @@ properties:
           - const: kontron,imx8mm-n801x-som
           - const: fsl,imx8mm
 
+      - description: Toradex Boards with Verdin iMX8M Mini Modules
+        items:
+          - enum:
+              - toradex,verdin-imx8mm-nonwifi-dahlia # Verdin iMX8M Mini Module on Dahlia
+              - toradex,verdin-imx8mm-nonwifi-dev    # Verdin iMX8M Mini Module on Verdin Development Board
+          - const: toradex,verdin-imx8mm-nonwifi     # Verdin iMX8M Mini Module without Wi-Fi / BT
+          - const: toradex,verdin-imx8mm             # Verdin iMX8M Mini Module
+          - const: fsl,imx8mm
+
+      - description: Toradex Boards with Verdin iMX8M Mini Wi-Fi / BT Modules
+        items:
+          - enum:
+              - toradex,verdin-imx8mm-wifi-dahlia # Verdin iMX8M Mini Wi-Fi / BT Module on Dahlia
+              - toradex,verdin-imx8mm-wifi-dev    # Verdin iMX8M Mini Wi-Fi / BT M. on Verdin Development B.
+          - const: toradex,verdin-imx8mm-wifi     # Verdin iMX8M Mini Wi-Fi / BT Module
+          - const: toradex,verdin-imx8mm          # Verdin iMX8M Mini Module
+          - const: fsl,imx8mm
+
       - description: Variscite VAR-SOM-MX8MM based boards
         items:
           - const: variscite,var-som-mx8mm-symphony
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 11/11] arm64: dts: freescale: add initial support for verdin imx8m mini

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This patch adds the device tree to support Toradex Verdin iMX8M Mini a
computer on module which can be used on different carrier boards.

The module consists of an NXP i.MX 8M Mini family SoC (either i.MX 8M
Mini Quad or 8M Mini DualLite), a PCA9450A PMIC, a Gigabit Ethernet PHY,
1 or 2 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional SPI CAN controller plus an optional Bluetooth/
Wi-Fi module.

Anything that is not self-contained on the module is disabled by
default.

The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.

The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.

So far there is no display functionality supported at all but basic
console UART, USB host, eMMC and Ethernet and PCIe functionality work
fine.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Remove bootargs which will be filled in by the bootloader as requested
  by Krzysztof.
- Remove the previously #ifdefed-out spi-nor as requested by Krzysztof.
- Fix capitalisation in cover-letter.

 arch/arm64/boot/dts/freescale/Makefile        |    4 +
 .../dts/freescale/imx8mm-verdin-dahlia.dtsi   |  143 ++
 .../boot/dts/freescale/imx8mm-verdin-dev.dtsi |   67 +
 .../imx8mm-verdin-nonwifi-dahlia.dts          |   18 +
 .../freescale/imx8mm-verdin-nonwifi-dev.dts   |   18 +
 .../dts/freescale/imx8mm-verdin-nonwifi.dtsi  |   75 +
 .../freescale/imx8mm-verdin-wifi-dahlia.dts   |   18 +
 .../dts/freescale/imx8mm-verdin-wifi-dev.dts  |   18 +
 .../dts/freescale/imx8mm-verdin-wifi.dtsi     |   95 ++
 .../boot/dts/freescale/imx8mm-verdin.dtsi     | 1267 +++++++++++++++++
 10 files changed, 1723 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6d8f0a532587..04380f2e44a2 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -63,6 +63,10 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dev.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
new file mode 100644
index 000000000000..b5bf025c74a2
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	sound_card: sound-card {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx8mm-wm8904";
+		simple-audio-card,routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Headphone Jack", "MICBIAS",
+			"IN1L", "Headphone Jack";
+		simple-audio-card,widgets =
+			"Microphone", "Headphone Jack",
+			"Headphone", "Headphone Jack",
+			"Line", "Line In Jack";
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+			sound-dai = <&wm8904_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+	};
+};
+
+/* Verdin SPI_1 */
+&ecspi2 {
+	status = "okay";
+};
+
+/* EEPROM on display adapter boards */
+&eeprom_display_adapter {
+	status = "okay";
+};
+
+/* EEPROM on Verdin Development board */
+&eeprom_carrier_board {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	status = "okay";
+};
+
+/* Current measurement into module VCC */
+&hwmon {
+	status = "okay";
+};
+
+&hwmon_temp {
+	vs-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	status = "okay";
+
+	/* Audio Codec */
+	wm8904_1a: codec@1a {
+		compatible = "wlf,wm8904";
+		AVDD-supply = <&reg_3p3v>;
+		clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+		clock-names = "mclk";
+		CPVDD-supply = <&reg_3p3v>;
+		DBVDD-supply = <&reg_3p3v>;
+		DCVDD-supply = <&reg_3p3v>;
+		MICVDD-supply = <&reg_3p3v>;
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+/* Verdin PCIE_1 */
+
+/* Verdin PWM_3_DSI */
+&pwm1 {
+	status = "okay";
+};
+
+/* Verdin PWM_1 */
+&pwm2 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&pwm3 {
+	status = "okay";
+};
+
+/* VERDIN I2S_1 */
+&sai2 {
+	status = "okay";
+};
+
+/* Verdin UART_3 */
+&uart1 {
+	status = "okay";
+};
+
+/* Verdin UART_1 */
+&uart2 {
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&uart3 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usbotg1 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usbotg2 {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
new file mode 100644
index 000000000000..f35d22dc546b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	sound_card: sound-card {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx8mm-nau8822";
+		simple-audio-card,routing =
+			"Headphones", "LHP",
+			"Headphones", "RHP",
+			"Speaker", "LSPK",
+			"Speaker", "RSPK",
+			"Line Out", "AUXOUT1",
+			"Line Out", "AUXOUT2",
+			"LAUX", "Line In",
+			"RAUX", "Line In",
+			"LMICP", "Mic In",
+			"RMICP", "Mic In";
+		simple-audio-card,widgets =
+			"Headphones", "Headphones",
+			"Line Out", "Line Out",
+			"Speaker", "Speaker",
+			"Microphone", "Mic In",
+			"Line", "Line In";
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+			sound-dai = <&nau8822_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+	};
+};
+
+&gpio_expander_21 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	/* Audio Codec */
+	nau8822_1a: codec@1a {
+		compatible = "nuvoton,nau8822";
+		reg = <0x1a>;
+	};
+};
+
+/* Verdin UART_1, connector X50 through RS485 transceiver */
+&uart2 {
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+};
+
+/* Limit frequency on dev board due to long traces and bad signal integrity */
+&usdhc2 {
+	max-frequency = <100000000>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
new file mode 100644
index 000000000000..d64ff378a152
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-nonwifi.dtsi"
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini on Dahlia Board";
+	compatible = "toradex,verdin-imx8mm-nonwifi-dahlia",
+		     "toradex,verdin-imx8mm-nonwifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
new file mode 100644
index 000000000000..6ae71ecac8de
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-nonwifi.dtsi"
+#include "imx8mm-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mm-nonwifi-dev",
+		     "toradex,verdin-imx8mm-nonwifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
new file mode 100644
index 000000000000..9aff9dde1a02
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_64",
+			  "SODIMM_21",
+			  "SODIMM_206",
+			  "SODIMM_76",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "SODIMM_162",
+			  "SODIMM_164",
+			  "SODIMM_166",
+			  "SODIMM_168",
+			  "SODIMM_66",
+			  "SODIMM_17",
+			  "",
+			  "SODIMM_156",
+			  "SODIMM_160",
+			  "SODIMM_244",
+			  "SODIMM_250",
+			  "SODIMM_48",
+			  "SODIMM_44",
+			  "SODIMM_42",
+			  "SODIMM_46";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_102",
+			  "SODIMM_90",
+			  "SODIMM_92",
+			  "SODIMM_94",
+			  "SODIMM_96",
+			  "SODIMM_100",
+			  "SODIMM_148",
+			  "SODIMM_152",
+			  "SODIMM_154",
+			  "SODIMM_174",
+			  "SODIMM_120",
+			  "SODIMM_104",
+			  "SODIMM_106",
+			  "SODIMM_108",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "SODIMM_150",
+			  "SODIMM_118",
+			  "",
+			  "SODIMM_88",
+			  "SODIMM_149",
+			  "SODIMM_147",
+			  "SODIMM_36",
+			  "SODIMM_32",
+			  "SODIMM_30",
+			  "SODIMM_34",
+			  "SODIMM_38",
+			  "SODIMM_252",
+			  "SODIMM_133",
+			  "SODIMM_135",
+			  "SODIMM_129";
+};
+
+&usdhc3 {
+	bus-width = <4>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
new file mode 100644
index 000000000000..d424c475cba1
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-wifi.dtsi"
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini WB on Dahlia Board";
+	compatible = "toradex,verdin-imx8mm-wifi-dahlia",
+		     "toradex,verdin-imx8mm-wifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
new file mode 100644
index 000000000000..ef952021832e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-wifi.dtsi"
+#include "imx8mm-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini WB on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mm-wifi-dev",
+		     "toradex,verdin-imx8mm-wifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
new file mode 100644
index 000000000000..c400770c1df5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_wifi_en: regulator-wifi-en {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "PDn_AW-CM276NF";
+		startup-delay-us = <2000>;
+	};
+};
+
+/* On-module Wi-Fi */
+&usdhc3 {
+	bus-width = <4>;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_wifi_ctrl>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_wifi_ctrl>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_wifi_ctrl>;
+	vmmc-supply = <&reg_wifi_en>;
+	wifi-host;
+	status = "okay";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_64",
+			  "SODIMM_21",
+			  "SODIMM_206",
+			  "SODIMM_76",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_66",
+			  "SODIMM_17",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_244",
+			  "SODIMM_250",
+			  "SODIMM_48",
+			  "SODIMM_44",
+			  "SODIMM_42",
+			  "SODIMM_46";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_102",
+			  "SODIMM_90",
+			  "SODIMM_92",
+			  "SODIMM_94",
+			  "SODIMM_96",
+			  "SODIMM_100",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_174",
+			  "SODIMM_120",
+			  "SODIMM_104",
+			  "SODIMM_106",
+			  "SODIMM_108",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "",
+			  "SODIMM_118",
+			  "",
+			  "SODIMM_88",
+			  "SODIMM_149",
+			  "SODIMM_147",
+			  "SODIMM_36",
+			  "SODIMM_32",
+			  "SODIMM_30",
+			  "SODIMM_34",
+			  "SODIMM_38",
+			  "SODIMM_252",
+			  "SODIMM_133",
+			  "SODIMM_135",
+			  "SODIMM_129";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
new file mode 100644
index 000000000000..2fa9dc3dd92b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
@@ -0,0 +1,1267 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "dt-bindings/pwm/pwm.h"
+#include "imx8mm.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>;
+		power-supply = <&reg_3p3v>;
+		/* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */
+		pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	/* Fixed clock dedicated to SPI CAN controller */
+	clk20m: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <20000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			/* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */
+			gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	/* Carrier Board Supplies */
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "+V1.8_SW";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SW";
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "+V5_SW";
+	};
+
+	/* Non PMIC On-module Supplies */
+	reg_ethphy: regulator-ethphy {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */
+		off-on-delay = <500000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_eth>;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_ETH";
+		startup-delay-us = <200000>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_1_EN (SODIMM 155) */
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_en>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_otg1_vbus";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_2_EN (SODIMM 185) */
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2_en>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_otg2_vbus";
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin SD_1_PWR_EN (SODIMM 76) */
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		off-on-delay = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SD";
+		startup-delay-us = <2000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* Use the kernel configuration settings instead */
+		/delete-node/ linux,cma;
+
+		rpmsg_reserved: rpmsg@b8000000 {
+			no-map;
+			reg = <0 0xb8000000 0 0x400000>;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+/* Verdin SPI_1 */
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+};
+
+/* Verdin CAN_1 and CAN_2 (On-module) */
+&ecspi3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>,
+		   <&gpio1 5 GPIO_ACTIVE_LOW>;
+	spi-num-chipselects = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+
+	can1: can@0 {
+		compatible = "microchip,mcp251xfd";
+		clocks = <&clk20m>;
+		interrupts-extended = <&gpio1 6 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can1_int>;
+		reg = <0>;
+		spi-max-frequency = <8500000>;
+	};
+
+	can2: can@1 {
+		compatible = "microchip,mcp251xfd";
+		clocks = <&clk20m>;
+		interrupts-extended = <&gpio1 7 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can2_int>;
+		reg = <1>;
+		spi-max-frequency = <8500000>;
+		/* Not assembled on regular SKUs */
+		status = "disabled";
+	};
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&fec1 {
+	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_ethphy>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-1 = <&pinctrl_fec1_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_216",
+			  "SODIMM_19",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_220",
+			  "SODIMM_222",
+			  "",
+			  "SODIMM_218",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_185",
+			  "SODIMM_187";
+};
+
+&gpio2 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_84",
+			  "SODIMM_78",
+			  "SODIMM_74",
+			  "SODIMM_80",
+			  "SODIMM_82",
+			  "SODIMM_70",
+			  "SODIMM_72";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_131",
+			  "",
+			  "SODIMM_91",
+			  "SODIMM_16",
+			  "SODIMM_15",
+			  "SODIMM_208",
+			  "SODIMM_137",
+			  "SODIMM_139",
+			  "SODIMM_141",
+			  "SODIMM_143",
+			  "SODIMM_196",
+			  "SODIMM_200",
+			  "SODIMM_198",
+			  "SODIMM_202",
+			  "",
+			  "",
+			  "SODIMM_55",
+			  "SODIMM_53",
+			  "SODIMM_95",
+			  "SODIMM_93",
+			  "SODIMM_14",
+			  "SODIMM_12",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_210",
+			  "SODIMM_212",
+			  "SODIMM_151",
+			  "SODIMM_153";
+
+	ctrl_sleep_moci-hog {
+		gpio-hog;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		line-name = "CTRL_SLEEP_MOCI#";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+	};
+};
+
+/* On-module I2C */
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		interrupt-parent = <&gpio1>;
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x25>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+
+		regulators {
+			reg_vdd_soc: BUCK1 {
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <850000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "+VDD_SOC";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <850000>;
+				regulator-name = "+VDD_ARM";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_dram: BUCK3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <850000>;
+				regulator-name = "+VDD_GPU_VPU_DDR";
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "+V3.3";
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "PWR_1V8_MOCI";
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1100000>;
+				regulator-name = "+VDD_DDR";
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_SNVS";
+			};
+
+			reg_vdd_snvs: LDO2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "+V0.8_SNVS";
+			};
+
+			reg_vdda: LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8A";
+			};
+
+			reg_vdd_phy: LDO4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <900000>;
+				regulator-name = "+V0.9_MIPI";
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V3.3_1.8_SD";
+			};
+		};
+	};
+
+	rtc_i2c: rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+	};
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Verdin I2C_1 (ADC_4 - ADC_3) */
+		channel@0 {
+			reg = <0>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_4 - ADC_1) */
+		channel@1 {
+			reg = <1>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_3 - ADC_1) */
+		channel@2 {
+			reg = <2>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_2 - ADC_1) */
+		channel@3 {
+			reg = <3>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_4 */
+		channel@4 {
+			reg = <4>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_3 */
+		channel@5 {
+			reg = <5>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_2 */
+		channel@6 {
+			reg = <6>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_1 */
+		channel@7 {
+			reg = <7>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+	};
+
+	eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	clock-frequency = <10000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+};
+
+/* Verdin I2C_3_HDMI N/A */
+
+/* Verdin I2C_4_CSI */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	gpio_expander_21: gpio-expander@21 {
+		compatible = "nxp,pcal6416";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x21>;
+		status = "disabled";
+		vcc-supply = <&reg_3p3v>;
+	};
+
+	lvds_ti_sn65dsi83: bridge@2c {
+		compatible = "ti,sn65dsi83";
+		/* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		enable-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>;
+		reg = <0x2c>;
+		status = "disabled";
+	};
+
+	/* Current measurement into module VCC */
+	hwmon: hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+		status = "disabled";
+	};
+
+	hdmi_lontium_lt8912: hdmi@48 {
+		compatible = "lontium,lt8912b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>;
+		reg = <0x48>;
+		/* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		reset-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	atmel_mxt_ts: touch@4a {
+		compatible = "atmel,maxtouch";
+		/* Verdin GPIO_9_DSI */
+		/* (TOUCH_INT#, SODIMM 17, also routed to SN65dsi83 IRQ albeit currently unused) */
+		interrupt-parent = <&gpio3>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>;
+		reg = <0x4a>;
+		/* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */
+		reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	/* Temperature sensor on carrier board */
+	hwmon_temp: sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+		status = "disabled";
+	};
+
+	/* EEPROM on display adapter (MIPI DSI Display Adapter) */
+	eeprom_display_adapter: eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+		status = "disabled";
+	};
+
+	/* EEPROM on carrier board */
+	eeprom_carrier_board: eeprom@57 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x57>;
+		status = "disabled";
+	};
+};
+
+/* Verdin PWM_3_DSI */
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_1>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_1 */
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_2>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_2 */
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_3>;
+	#pwm-cells = <3>;
+};
+
+/* VERDIN I2S_1 */
+&sai2 {
+	#sound-dai-cells = <0>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux console */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+/* Verdin UART_1 */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_2 */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_4 */
+/*
+ * Resource allocated to M4 by default, must not be accessed from Cortex-A35 or you get an OOPS
+ */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+&usbmisc1 {
+	vbus-wakeup-supply = <&reg_vdd_3v3>;
+};
+
+&usbmisc2 {
+	vbus-wakeup-supply = <&reg_vdd_3v3>;
+};
+
+/* Verdin USB_1 */
+&usbotg1 {
+	adp-disable;
+	dr_mode = "otg";
+	hnp-disable;
+	over-current-active-low;
+	picophy,dc-vol-level-adjust = <7>;
+	picophy,pre-emp-curr-control = <3>;
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+};
+
+/* Verdin USB_2 */
+&usbotg2 {
+	dr_mode = "host";
+	over-current-active-low;
+	picophy,dc-vol-level-adjust = <7>;
+	picophy,pre-emp-curr-control = <3>;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+};
+
+&usbphynop1 {
+	vcc-supply = <&reg_vdd_3v3>;
+};
+
+&usbphynop2 {
+	vcc-supply = <&reg_vdd_3v3>;
+};
+
+/* On-module eMMC */
+&usdhc1 {
+	bus-width = <8>;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	pm-ignore-notify;
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+};
+
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>,
+		    <&pinctrl_gpio_hog1>, <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>,
+		    <&pinctrl_pmic_tpm_ena>;
+
+	pinctrl_can1_int: can1intgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x1c4>;	/* CAN_1_SPI_INT#_1.8V */
+	};
+
+	pinctrl_can2_int: can2intgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x1c4>;	/* CAN_2_SPI_INT#_1.8V */
+	};
+
+	pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x1c4>;	/* SODIMM 256 */
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x4>,	/* SODIMM 196 */
+			<MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x4>,	/* SODIMM 200 */
+			<MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x1c4>,	/* SODIMM 198 */
+			<MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x1c4>;	/* SODIMM 202 */
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x4>,	/* CAN_SPI_SCK_1.8V */
+			<MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x4>,	/* CAN_SPI_MOSI_1.8V */
+			<MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x1c4>,	/* CAN_SPI_MISO_1.8V */
+			<MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x1c4>,	/* CAN_1_SPI_CS_1.8V# */
+			<MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x1c4>;	/* CAN_2_SPI_CS#_1.8V */
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x3>,
+			<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3>,
+			<MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f>,
+			<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91>,
+			<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91>,
+			<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91>,
+			<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91>,
+			<MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f>,
+			<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91>,
+			<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91>,
+			<MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f>,
+			<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x1c4>;
+	};
+
+	pinctrl_fec1_sleep: fec1-sleepgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x3>,
+			<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3>,
+			<MX8MM_IOMUXC_ENET_TD3_GPIO1_IO18		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD2_GPIO1_IO19		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD1_GPIO1_IO20		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD0_GPIO1_IO21		0x1f>,
+			<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91>,
+			<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91>,
+			<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91>,
+			<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91>,
+			<MX8MM_IOMUXC_ENET_TXC_GPIO1_IO23		0x1f>,
+			<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91>,
+			<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91>,
+			<MX8MM_IOMUXC_ENET_TX_CTL_GPIO1_IO22		0x1f>,
+			<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x184>;
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x1c2>,	/* SODIMM 52 */
+			<MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B		0x82>,	/* SODIMM 54 */
+			<MX8MM_IOMUXC_NAND_CE1_B_QSPI_A_SS1_B		0x82>,	/* SODIMM 64 */
+			<MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS		0x82>,	/* SODIMM 66 */
+			<MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0		0x82>,	/* SODIMM 56 */
+			<MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1		0x82>,	/* SODIMM 58 */
+			<MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2		0x82>,	/* SODIMM 60 */
+			<MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3		0x82>;	/* SODIMM 62 */
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4		0x184>;	/* SODIMM 206 */
+	};
+
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5		0x1c4>;	/* SODIMM 208 */
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART3_RXD_GPIO5_IO26		0x184>;	/* SODIMM 210 */
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART3_TXD_GPIO5_IO27		0x184>;	/* SODIMM 212 */
+	};
+
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x184>;	/* SODIMM 216 */
+	};
+
+	pinctrl_gpio6: gpio6grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x184>;	/* SODIMM 218 */
+	};
+
+	pinctrl_gpio7: gpio7grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x184>;	/* SODIMM 220 */
+	};
+
+	pinctrl_gpio8: gpio8grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x184>;	/* SODIMM 222 */
+	};
+
+	/* Verdin GPIO_9_DSI (pulled-up as active-low) */
+	pinctrl_gpio_9_dsi: gpio9dsigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15		0x1c4>;	/* SODIMM 17 */
+	};
+
+	/* Verdin GPIO_10_DSI */
+	pinctrl_gpio_10_dsi: gpio10dsigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3		0x1c4>;	/* SODIMM 21 */
+	};
+
+	pinctrl_gpio_hog1: gpiohog1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20		0x1c4>,	/* SODIMM 88 */
+			<MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1		0x1c4>,	/* SODIMM 90 */
+			<MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2		0x1c4>,	/* SODIMM 92 */
+			<MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3		0x1c4>,	/* SODIMM 94 */
+			<MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4		0x1c4>,	/* SODIMM 96 */
+			<MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5		0x1c4>,	/* SODIMM 100 */
+			<MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0		0x1c4>,	/* SODIMM 102 */
+			<MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11		0x1c4>,	/* SODIMM 104 */
+			<MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12		0x1c4>,	/* SODIMM 106 */
+			<MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13		0x1c4>,	/* SODIMM 108 */
+			<MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x1c4>,	/* SODIMM 112 */
+			<MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x1c4>,	/* SODIMM 114 */
+			<MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x1c4>,	/* SODIMM 116 */
+			<MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x1c4>,	/* SODIMM 118 */
+			<MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10		0x1c4>;	/* SODIMM 120 */
+	};
+
+	pinctrl_gpio_hog2: gpiohog2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x1c4>;	/* SODIMM 91 */
+	};
+
+	pinctrl_gpio_hog3: gpiohog3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13		0x1c4>,	/* SODIMM 157 */
+			<MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15		0x1c4>;	/* SODIMM 187 */
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x1c4>;	/* SODIMM 252 */
+	};
+
+	/* On-module I2C */
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	/* Verdin I2C_4_CSI */
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x400001c6>,	/* SODIMM 55 */
+			<MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x400001c6>;	/* SODIMM 53 */
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16		0x400001c6>,	/* SODIMM 55 */
+			<MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17		0x400001c6>;	/* SODIMM 53 */
+	};
+
+	/* Verdin I2C_2_DSI */
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x400001c6>,	/* SODIMM 95 */
+			<MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x400001c6>;	/* SODIMM 93 */
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18		0x400001c6>,	/* SODIMM 95 */
+			<MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19		0x400001c6>;	/* SODIMM 93 */
+	};
+
+	/* Verdin I2C_1 */
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c6>,	/* SODIMM 14 */
+			<MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c6>;	/* SODIMM 12 */
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C4_SCL_GPIO5_IO20		0x400001c6>,	/* SODIMM 14 */
+			<MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21		0x400001c6>;	/* SODIMM 12 */
+	};
+
+	/* Verdin I2S_2_BCLK (TOUCH_RESET#) */
+	pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x184>;	/* SODIMM 42 */
+	};
+
+	/* Verdin I2S_2_D_OUT shared with SAI5 */
+	pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24		0x184>;	/* SODIMM 46 */
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x6>,	/* SODIMM 244 */
+			/* PMIC_EN_PCIe_CLK, unused */
+			<MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x6>;
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41>;	/* PMIC_INT# */
+	};
+
+	/* Verdin PWM_3_DSI shared with GPIO1_IO1 */
+	pinctrl_pwm_1: pwm1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT		0x6>;	/* SODIMM 19 */
+	};
+
+	pinctrl_pwm_2: pwm2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x6>;	/* SODIMM 15 */
+	};
+
+	pinctrl_pwm_3: pwm3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT			0x6>;	/* SODIMM 16 */
+	};
+
+	/* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM1_OUT */
+	pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsihpdgpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x184>;	/* SODIMM 19 */
+	};
+
+	pinctrl_reg_eth: regethgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x184>;	/* PMIC_EN_ETH */
+	};
+
+	pinctrl_reg_usb1_en: regusb1engrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x184>;	/* SODIMM 155 */
+	};
+
+	pinctrl_reg_usb2_en: regusb2engrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x184>;	/* SODIMM 185 */
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC		0xd6>,	/* SODIMM 32 */
+			<MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK		0xd6>,	/* SODIMM 30 */
+			<MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK		0xd6>,	/* SODIMM 38 */
+			<MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0		0xd6>,	/* SODIMM 36 */
+			<MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0		0xd6>;	/* SODIMM 34 */
+	};
+
+	pinctrl_sai5: sai5grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0		0xd6>,	/* SODIMM 48 */
+			<MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC		0xd6>,	/* SODIMM 44 */
+			<MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK		0xd6>,	/* SODIMM 42 */
+			<MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0		0xd6>;	/* SODIMM 46 */
+	};
+
+	/* control signal for optional ATTPM20P or SE050 */
+	pinctrl_pmic_tpm_ena: pmictpmenagrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x1c4>;	/* PMIC_TPM_ENA */
+	};
+
+	pinctrl_tsp: tspgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6		0x140>,	/* SODIMM 148 */
+			<MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7		0x140>,	/* SODIMM 152 */
+			<MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8		0x140>,	/* SODIMM 154 */
+			<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x140>,	/* SODIMM 179 */
+			<MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x140>;	/* SODIMM 150 */
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x1c4>,	/* SODIMM 149 */
+			<MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x1c4>;	/* SODIMM 147 */
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x1c4>,	/* SODIMM 129 */
+			<MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x1c4>,	/* SODIMM 131 */
+			<MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x1c4>,	/* SODIMM 133 */
+			<MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x1c4>;	/* SODIMM 135 */
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX		0x1c4>,	/* SODIMM 137 */
+			<MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX		0x1c4>,	/* SODIMM 139 */
+			<MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x1c4>,	/* SODIMM 141 */
+			<MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x1c4>;	/* SODIMM 143 */
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x1c4>,	/* SODIMM 151 */
+			<MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x1c4>;	/* SODIMM 153 */
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x190>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196>;
+	};
+
+	pinctrl_usdhc2_cd: usdhc2cdgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x1c4>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_pwr_en: usdhc2pwrengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5		0x184>;	/* SODIMM 76 */
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x190>,	/* SODIMM 78 */
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0>,	/* SODIMM 74 */
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0>,	/* SODIMM 80 */
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0>,	/* SODIMM 82 */
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0>,	/* SODIMM 70 */
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0>,	/* SODIMM 72 */
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194>,
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196>,
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6>,
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0>;
+	};
+
+	/* On-module Wi-Fi/BT or type specific SDHC interface */
+	/* (e.g. on X52 extension slot of Verdin Development Board) */
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x190>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d0>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d6>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6>;	/* PMIC_WDI */
+	};
+
+	pinctrl_wifi_ctrl: wifictrlgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x1c4>,	/* WIFI_WKUP_BT */
+			<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x1c4>,	/* WIFI_W_WKUP_HOST */
+			<MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x1c4>;	/* WIFI_WKUP_WLAN */
+	};
+
+	pinctrl_wifi_i2s: bti2sgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_RXD4_SAI6_TX_BCLK		0xd6>,	/* WIFI_TX_BCLK */
+			<MX8MM_IOMUXC_SAI1_RXD5_SAI6_TX_DATA0		0xd6>,	/* WIFI_TX_DATA0 */
+			<MX8MM_IOMUXC_SAI1_RXD6_SAI6_TX_SYNC		0xd6>,	/* WIFI_TX_SYNC */
+			<MX8MM_IOMUXC_SAI1_TXD5_SAI6_RX_DATA0		0xd6>;	/* WIFI_RX_DATA0 */
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x184>;	/* PMIC_EN_WIFI */
+	};
+};
-- 
2.33.1

[PATCH v2 11/11] arm64: dts: freescale: add initial support for verdin imx8m mini

[Marcel Ziswiler]

From: Marcel Ziswiler <marcel.ziswiler@toradex.com>

This patch adds the device tree to support Toradex Verdin iMX8M Mini a
computer on module which can be used on different carrier boards.

The module consists of an NXP i.MX 8M Mini family SoC (either i.MX 8M
Mini Quad or 8M Mini DualLite), a PCA9450A PMIC, a Gigabit Ethernet PHY,
1 or 2 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional SPI CAN controller plus an optional Bluetooth/
Wi-Fi module.

Anything that is not self-contained on the module is disabled by
default.

The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.

The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.

So far there is no display functionality supported at all but basic
console UART, USB host, eMMC and Ethernet and PCIe functionality work
fine.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

---

Changes in v2:
- Remove bootargs which will be filled in by the bootloader as requested
  by Krzysztof.
- Remove the previously #ifdefed-out spi-nor as requested by Krzysztof.
- Fix capitalisation in cover-letter.

 arch/arm64/boot/dts/freescale/Makefile        |    4 +
 .../dts/freescale/imx8mm-verdin-dahlia.dtsi   |  143 ++
 .../boot/dts/freescale/imx8mm-verdin-dev.dtsi |   67 +
 .../imx8mm-verdin-nonwifi-dahlia.dts          |   18 +
 .../freescale/imx8mm-verdin-nonwifi-dev.dts   |   18 +
 .../dts/freescale/imx8mm-verdin-nonwifi.dtsi  |   75 +
 .../freescale/imx8mm-verdin-wifi-dahlia.dts   |   18 +
 .../dts/freescale/imx8mm-verdin-wifi-dev.dts  |   18 +
 .../dts/freescale/imx8mm-verdin-wifi.dtsi     |   95 ++
 .../boot/dts/freescale/imx8mm-verdin.dtsi     | 1267 +++++++++++++++++
 10 files changed, 1723 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6d8f0a532587..04380f2e44a2 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -63,6 +63,10 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dev.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
new file mode 100644
index 000000000000..b5bf025c74a2
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	sound_card: sound-card {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx8mm-wm8904";
+		simple-audio-card,routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Headphone Jack", "MICBIAS",
+			"IN1L", "Headphone Jack";
+		simple-audio-card,widgets =
+			"Microphone", "Headphone Jack",
+			"Headphone", "Headphone Jack",
+			"Line", "Line In Jack";
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+			sound-dai = <&wm8904_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+	};
+};
+
+/* Verdin SPI_1 */
+&ecspi2 {
+	status = "okay";
+};
+
+/* EEPROM on display adapter boards */
+&eeprom_display_adapter {
+	status = "okay";
+};
+
+/* EEPROM on Verdin Development board */
+&eeprom_carrier_board {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	status = "okay";
+};
+
+/* Current measurement into module VCC */
+&hwmon {
+	status = "okay";
+};
+
+&hwmon_temp {
+	vs-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	status = "okay";
+
+	/* Audio Codec */
+	wm8904_1a: codec@1a {
+		compatible = "wlf,wm8904";
+		AVDD-supply = <&reg_3p3v>;
+		clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+		clock-names = "mclk";
+		CPVDD-supply = <&reg_3p3v>;
+		DBVDD-supply = <&reg_3p3v>;
+		DCVDD-supply = <&reg_3p3v>;
+		MICVDD-supply = <&reg_3p3v>;
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+/* Verdin PCIE_1 */
+
+/* Verdin PWM_3_DSI */
+&pwm1 {
+	status = "okay";
+};
+
+/* Verdin PWM_1 */
+&pwm2 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&pwm3 {
+	status = "okay";
+};
+
+/* VERDIN I2S_1 */
+&sai2 {
+	status = "okay";
+};
+
+/* Verdin UART_3 */
+&uart1 {
+	status = "okay";
+};
+
+/* Verdin UART_1 */
+&uart2 {
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&uart3 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usbotg1 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usbotg2 {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
new file mode 100644
index 000000000000..f35d22dc546b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	sound_card: sound-card {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx8mm-nau8822";
+		simple-audio-card,routing =
+			"Headphones", "LHP",
+			"Headphones", "RHP",
+			"Speaker", "LSPK",
+			"Speaker", "RSPK",
+			"Line Out", "AUXOUT1",
+			"Line Out", "AUXOUT2",
+			"LAUX", "Line In",
+			"RAUX", "Line In",
+			"LMICP", "Mic In",
+			"RMICP", "Mic In";
+		simple-audio-card,widgets =
+			"Headphones", "Headphones",
+			"Line Out", "Line Out",
+			"Speaker", "Speaker",
+			"Microphone", "Mic In",
+			"Line", "Line In";
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+			sound-dai = <&nau8822_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+	};
+};
+
+&gpio_expander_21 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	/* Audio Codec */
+	nau8822_1a: codec@1a {
+		compatible = "nuvoton,nau8822";
+		reg = <0x1a>;
+	};
+};
+
+/* Verdin UART_1, connector X50 through RS485 transceiver */
+&uart2 {
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+};
+
+/* Limit frequency on dev board due to long traces and bad signal integrity */
+&usdhc2 {
+	max-frequency = <100000000>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
new file mode 100644
index 000000000000..d64ff378a152
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-nonwifi.dtsi"
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini on Dahlia Board";
+	compatible = "toradex,verdin-imx8mm-nonwifi-dahlia",
+		     "toradex,verdin-imx8mm-nonwifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
new file mode 100644
index 000000000000..6ae71ecac8de
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-nonwifi.dtsi"
+#include "imx8mm-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mm-nonwifi-dev",
+		     "toradex,verdin-imx8mm-nonwifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
new file mode 100644
index 000000000000..9aff9dde1a02
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_64",
+			  "SODIMM_21",
+			  "SODIMM_206",
+			  "SODIMM_76",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "SODIMM_162",
+			  "SODIMM_164",
+			  "SODIMM_166",
+			  "SODIMM_168",
+			  "SODIMM_66",
+			  "SODIMM_17",
+			  "",
+			  "SODIMM_156",
+			  "SODIMM_160",
+			  "SODIMM_244",
+			  "SODIMM_250",
+			  "SODIMM_48",
+			  "SODIMM_44",
+			  "SODIMM_42",
+			  "SODIMM_46";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_102",
+			  "SODIMM_90",
+			  "SODIMM_92",
+			  "SODIMM_94",
+			  "SODIMM_96",
+			  "SODIMM_100",
+			  "SODIMM_148",
+			  "SODIMM_152",
+			  "SODIMM_154",
+			  "SODIMM_174",
+			  "SODIMM_120",
+			  "SODIMM_104",
+			  "SODIMM_106",
+			  "SODIMM_108",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "SODIMM_150",
+			  "SODIMM_118",
+			  "",
+			  "SODIMM_88",
+			  "SODIMM_149",
+			  "SODIMM_147",
+			  "SODIMM_36",
+			  "SODIMM_32",
+			  "SODIMM_30",
+			  "SODIMM_34",
+			  "SODIMM_38",
+			  "SODIMM_252",
+			  "SODIMM_133",
+			  "SODIMM_135",
+			  "SODIMM_129";
+};
+
+&usdhc3 {
+	bus-width = <4>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
new file mode 100644
index 000000000000..d424c475cba1
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-wifi.dtsi"
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini WB on Dahlia Board";
+	compatible = "toradex,verdin-imx8mm-wifi-dahlia",
+		     "toradex,verdin-imx8mm-wifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
new file mode 100644
index 000000000000..ef952021832e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-wifi.dtsi"
+#include "imx8mm-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini WB on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mm-wifi-dev",
+		     "toradex,verdin-imx8mm-wifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
new file mode 100644
index 000000000000..c400770c1df5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_wifi_en: regulator-wifi-en {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "PDn_AW-CM276NF";
+		startup-delay-us = <2000>;
+	};
+};
+
+/* On-module Wi-Fi */
+&usdhc3 {
+	bus-width = <4>;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_wifi_ctrl>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_wifi_ctrl>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_wifi_ctrl>;
+	vmmc-supply = <&reg_wifi_en>;
+	wifi-host;
+	status = "okay";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_64",
+			  "SODIMM_21",
+			  "SODIMM_206",
+			  "SODIMM_76",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_66",
+			  "SODIMM_17",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_244",
+			  "SODIMM_250",
+			  "SODIMM_48",
+			  "SODIMM_44",
+			  "SODIMM_42",
+			  "SODIMM_46";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_102",
+			  "SODIMM_90",
+			  "SODIMM_92",
+			  "SODIMM_94",
+			  "SODIMM_96",
+			  "SODIMM_100",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_174",
+			  "SODIMM_120",
+			  "SODIMM_104",
+			  "SODIMM_106",
+			  "SODIMM_108",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "",
+			  "SODIMM_118",
+			  "",
+			  "SODIMM_88",
+			  "SODIMM_149",
+			  "SODIMM_147",
+			  "SODIMM_36",
+			  "SODIMM_32",
+			  "SODIMM_30",
+			  "SODIMM_34",
+			  "SODIMM_38",
+			  "SODIMM_252",
+			  "SODIMM_133",
+			  "SODIMM_135",
+			  "SODIMM_129";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
new file mode 100644
index 000000000000..2fa9dc3dd92b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
@@ -0,0 +1,1267 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "dt-bindings/pwm/pwm.h"
+#include "imx8mm.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>;
+		power-supply = <&reg_3p3v>;
+		/* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */
+		pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	/* Fixed clock dedicated to SPI CAN controller */
+	clk20m: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <20000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			/* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */
+			gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	/* Carrier Board Supplies */
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "+V1.8_SW";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SW";
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "+V5_SW";
+	};
+
+	/* Non PMIC On-module Supplies */
+	reg_ethphy: regulator-ethphy {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */
+		off-on-delay = <500000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_eth>;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_ETH";
+		startup-delay-us = <200000>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_1_EN (SODIMM 155) */
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_en>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_otg1_vbus";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_2_EN (SODIMM 185) */
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2_en>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_otg2_vbus";
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin SD_1_PWR_EN (SODIMM 76) */
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		off-on-delay = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SD";
+		startup-delay-us = <2000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* Use the kernel configuration settings instead */
+		/delete-node/ linux,cma;
+
+		rpmsg_reserved: rpmsg@b8000000 {
+			no-map;
+			reg = <0 0xb8000000 0 0x400000>;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+/* Verdin SPI_1 */
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+};
+
+/* Verdin CAN_1 and CAN_2 (On-module) */
+&ecspi3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>,
+		   <&gpio1 5 GPIO_ACTIVE_LOW>;
+	spi-num-chipselects = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+
+	can1: can@0 {
+		compatible = "microchip,mcp251xfd";
+		clocks = <&clk20m>;
+		interrupts-extended = <&gpio1 6 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can1_int>;
+		reg = <0>;
+		spi-max-frequency = <8500000>;
+	};
+
+	can2: can@1 {
+		compatible = "microchip,mcp251xfd";
+		clocks = <&clk20m>;
+		interrupts-extended = <&gpio1 7 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can2_int>;
+		reg = <1>;
+		spi-max-frequency = <8500000>;
+		/* Not assembled on regular SKUs */
+		status = "disabled";
+	};
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&fec1 {
+	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_ethphy>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-1 = <&pinctrl_fec1_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_216",
+			  "SODIMM_19",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_220",
+			  "SODIMM_222",
+			  "",
+			  "SODIMM_218",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_185",
+			  "SODIMM_187";
+};
+
+&gpio2 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_84",
+			  "SODIMM_78",
+			  "SODIMM_74",
+			  "SODIMM_80",
+			  "SODIMM_82",
+			  "SODIMM_70",
+			  "SODIMM_72";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_131",
+			  "",
+			  "SODIMM_91",
+			  "SODIMM_16",
+			  "SODIMM_15",
+			  "SODIMM_208",
+			  "SODIMM_137",
+			  "SODIMM_139",
+			  "SODIMM_141",
+			  "SODIMM_143",
+			  "SODIMM_196",
+			  "SODIMM_200",
+			  "SODIMM_198",
+			  "SODIMM_202",
+			  "",
+			  "",
+			  "SODIMM_55",
+			  "SODIMM_53",
+			  "SODIMM_95",
+			  "SODIMM_93",
+			  "SODIMM_14",
+			  "SODIMM_12",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_210",
+			  "SODIMM_212",
+			  "SODIMM_151",
+			  "SODIMM_153";
+
+	ctrl_sleep_moci-hog {
+		gpio-hog;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		line-name = "CTRL_SLEEP_MOCI#";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+	};
+};
+
+/* On-module I2C */
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		interrupt-parent = <&gpio1>;
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x25>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+
+		regulators {
+			reg_vdd_soc: BUCK1 {
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <850000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "+VDD_SOC";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <850000>;
+				regulator-name = "+VDD_ARM";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_dram: BUCK3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <950000>;
+				regulator-min-microvolt = <850000>;
+				regulator-name = "+VDD_GPU_VPU_DDR";
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "+V3.3";
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "PWR_1V8_MOCI";
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1100000>;
+				regulator-name = "+VDD_DDR";
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_SNVS";
+			};
+
+			reg_vdd_snvs: LDO2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "+V0.8_SNVS";
+			};
+
+			reg_vdda: LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8A";
+			};
+
+			reg_vdd_phy: LDO4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <900000>;
+				regulator-name = "+V0.9_MIPI";
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V3.3_1.8_SD";
+			};
+		};
+	};
+
+	rtc_i2c: rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+	};
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Verdin I2C_1 (ADC_4 - ADC_3) */
+		channel@0 {
+			reg = <0>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_4 - ADC_1) */
+		channel@1 {
+			reg = <1>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_3 - ADC_1) */
+		channel@2 {
+			reg = <2>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_2 - ADC_1) */
+		channel@3 {
+			reg = <3>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_4 */
+		channel@4 {
+			reg = <4>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_3 */
+		channel@5 {
+			reg = <5>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_2 */
+		channel@6 {
+			reg = <6>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_1 */
+		channel@7 {
+			reg = <7>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+	};
+
+	eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	clock-frequency = <10000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+};
+
+/* Verdin I2C_3_HDMI N/A */
+
+/* Verdin I2C_4_CSI */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	gpio_expander_21: gpio-expander@21 {
+		compatible = "nxp,pcal6416";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x21>;
+		status = "disabled";
+		vcc-supply = <&reg_3p3v>;
+	};
+
+	lvds_ti_sn65dsi83: bridge@2c {
+		compatible = "ti,sn65dsi83";
+		/* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		enable-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>;
+		reg = <0x2c>;
+		status = "disabled";
+	};
+
+	/* Current measurement into module VCC */
+	hwmon: hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+		status = "disabled";
+	};
+
+	hdmi_lontium_lt8912: hdmi@48 {
+		compatible = "lontium,lt8912b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>;
+		reg = <0x48>;
+		/* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		reset-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	atmel_mxt_ts: touch@4a {
+		compatible = "atmel,maxtouch";
+		/* Verdin GPIO_9_DSI */
+		/* (TOUCH_INT#, SODIMM 17, also routed to SN65dsi83 IRQ albeit currently unused) */
+		interrupt-parent = <&gpio3>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>;
+		reg = <0x4a>;
+		/* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */
+		reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	/* Temperature sensor on carrier board */
+	hwmon_temp: sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+		status = "disabled";
+	};
+
+	/* EEPROM on display adapter (MIPI DSI Display Adapter) */
+	eeprom_display_adapter: eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+		status = "disabled";
+	};
+
+	/* EEPROM on carrier board */
+	eeprom_carrier_board: eeprom@57 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x57>;
+		status = "disabled";
+	};
+};
+
+/* Verdin PWM_3_DSI */
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_1>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_1 */
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_2>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_2 */
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_3>;
+	#pwm-cells = <3>;
+};
+
+/* VERDIN I2S_1 */
+&sai2 {
+	#sound-dai-cells = <0>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux console */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+/* Verdin UART_1 */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_2 */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_4 */
+/*
+ * Resource allocated to M4 by default, must not be accessed from Cortex-A35 or you get an OOPS
+ */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+&usbmisc1 {
+	vbus-wakeup-supply = <&reg_vdd_3v3>;
+};
+
+&usbmisc2 {
+	vbus-wakeup-supply = <&reg_vdd_3v3>;
+};
+
+/* Verdin USB_1 */
+&usbotg1 {
+	adp-disable;
+	dr_mode = "otg";
+	hnp-disable;
+	over-current-active-low;
+	picophy,dc-vol-level-adjust = <7>;
+	picophy,pre-emp-curr-control = <3>;
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+};
+
+/* Verdin USB_2 */
+&usbotg2 {
+	dr_mode = "host";
+	over-current-active-low;
+	picophy,dc-vol-level-adjust = <7>;
+	picophy,pre-emp-curr-control = <3>;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+};
+
+&usbphynop1 {
+	vcc-supply = <&reg_vdd_3v3>;
+};
+
+&usbphynop2 {
+	vcc-supply = <&reg_vdd_3v3>;
+};
+
+/* On-module eMMC */
+&usdhc1 {
+	bus-width = <8>;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	pm-ignore-notify;
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+};
+
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>,
+		    <&pinctrl_gpio_hog1>, <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>,
+		    <&pinctrl_pmic_tpm_ena>;
+
+	pinctrl_can1_int: can1intgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x1c4>;	/* CAN_1_SPI_INT#_1.8V */
+	};
+
+	pinctrl_can2_int: can2intgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x1c4>;	/* CAN_2_SPI_INT#_1.8V */
+	};
+
+	pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x1c4>;	/* SODIMM 256 */
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x4>,	/* SODIMM 196 */
+			<MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x4>,	/* SODIMM 200 */
+			<MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x1c4>,	/* SODIMM 198 */
+			<MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x1c4>;	/* SODIMM 202 */
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x4>,	/* CAN_SPI_SCK_1.8V */
+			<MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x4>,	/* CAN_SPI_MOSI_1.8V */
+			<MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x1c4>,	/* CAN_SPI_MISO_1.8V */
+			<MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x1c4>,	/* CAN_1_SPI_CS_1.8V# */
+			<MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x1c4>;	/* CAN_2_SPI_CS#_1.8V */
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x3>,
+			<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3>,
+			<MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f>,
+			<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91>,
+			<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91>,
+			<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91>,
+			<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91>,
+			<MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f>,
+			<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91>,
+			<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91>,
+			<MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f>,
+			<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x1c4>;
+	};
+
+	pinctrl_fec1_sleep: fec1-sleepgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x3>,
+			<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3>,
+			<MX8MM_IOMUXC_ENET_TD3_GPIO1_IO18		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD2_GPIO1_IO19		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD1_GPIO1_IO20		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD0_GPIO1_IO21		0x1f>,
+			<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91>,
+			<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91>,
+			<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91>,
+			<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91>,
+			<MX8MM_IOMUXC_ENET_TXC_GPIO1_IO23		0x1f>,
+			<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91>,
+			<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91>,
+			<MX8MM_IOMUXC_ENET_TX_CTL_GPIO1_IO22		0x1f>,
+			<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x184>;
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x1c2>,	/* SODIMM 52 */
+			<MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B		0x82>,	/* SODIMM 54 */
+			<MX8MM_IOMUXC_NAND_CE1_B_QSPI_A_SS1_B		0x82>,	/* SODIMM 64 */
+			<MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS		0x82>,	/* SODIMM 66 */
+			<MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0		0x82>,	/* SODIMM 56 */
+			<MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1		0x82>,	/* SODIMM 58 */
+			<MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2		0x82>,	/* SODIMM 60 */
+			<MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3		0x82>;	/* SODIMM 62 */
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4		0x184>;	/* SODIMM 206 */
+	};
+
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5		0x1c4>;	/* SODIMM 208 */
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART3_RXD_GPIO5_IO26		0x184>;	/* SODIMM 210 */
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART3_TXD_GPIO5_IO27		0x184>;	/* SODIMM 212 */
+	};
+
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x184>;	/* SODIMM 216 */
+	};
+
+	pinctrl_gpio6: gpio6grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x184>;	/* SODIMM 218 */
+	};
+
+	pinctrl_gpio7: gpio7grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x184>;	/* SODIMM 220 */
+	};
+
+	pinctrl_gpio8: gpio8grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x184>;	/* SODIMM 222 */
+	};
+
+	/* Verdin GPIO_9_DSI (pulled-up as active-low) */
+	pinctrl_gpio_9_dsi: gpio9dsigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15		0x1c4>;	/* SODIMM 17 */
+	};
+
+	/* Verdin GPIO_10_DSI */
+	pinctrl_gpio_10_dsi: gpio10dsigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3		0x1c4>;	/* SODIMM 21 */
+	};
+
+	pinctrl_gpio_hog1: gpiohog1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20		0x1c4>,	/* SODIMM 88 */
+			<MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1		0x1c4>,	/* SODIMM 90 */
+			<MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2		0x1c4>,	/* SODIMM 92 */
+			<MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3		0x1c4>,	/* SODIMM 94 */
+			<MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4		0x1c4>,	/* SODIMM 96 */
+			<MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5		0x1c4>,	/* SODIMM 100 */
+			<MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0		0x1c4>,	/* SODIMM 102 */
+			<MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11		0x1c4>,	/* SODIMM 104 */
+			<MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12		0x1c4>,	/* SODIMM 106 */
+			<MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13		0x1c4>,	/* SODIMM 108 */
+			<MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x1c4>,	/* SODIMM 112 */
+			<MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x1c4>,	/* SODIMM 114 */
+			<MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x1c4>,	/* SODIMM 116 */
+			<MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x1c4>,	/* SODIMM 118 */
+			<MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10		0x1c4>;	/* SODIMM 120 */
+	};
+
+	pinctrl_gpio_hog2: gpiohog2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x1c4>;	/* SODIMM 91 */
+	};
+
+	pinctrl_gpio_hog3: gpiohog3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13		0x1c4>,	/* SODIMM 157 */
+			<MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15		0x1c4>;	/* SODIMM 187 */
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x1c4>;	/* SODIMM 252 */
+	};
+
+	/* On-module I2C */
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	/* Verdin I2C_4_CSI */
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x400001c6>,	/* SODIMM 55 */
+			<MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x400001c6>;	/* SODIMM 53 */
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16		0x400001c6>,	/* SODIMM 55 */
+			<MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17		0x400001c6>;	/* SODIMM 53 */
+	};
+
+	/* Verdin I2C_2_DSI */
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x400001c6>,	/* SODIMM 95 */
+			<MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x400001c6>;	/* SODIMM 93 */
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18		0x400001c6>,	/* SODIMM 95 */
+			<MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19		0x400001c6>;	/* SODIMM 93 */
+	};
+
+	/* Verdin I2C_1 */
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c6>,	/* SODIMM 14 */
+			<MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c6>;	/* SODIMM 12 */
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C4_SCL_GPIO5_IO20		0x400001c6>,	/* SODIMM 14 */
+			<MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21		0x400001c6>;	/* SODIMM 12 */
+	};
+
+	/* Verdin I2S_2_BCLK (TOUCH_RESET#) */
+	pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x184>;	/* SODIMM 42 */
+	};
+
+	/* Verdin I2S_2_D_OUT shared with SAI5 */
+	pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24		0x184>;	/* SODIMM 46 */
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x6>,	/* SODIMM 244 */
+			/* PMIC_EN_PCIe_CLK, unused */
+			<MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x6>;
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41>;	/* PMIC_INT# */
+	};
+
+	/* Verdin PWM_3_DSI shared with GPIO1_IO1 */
+	pinctrl_pwm_1: pwm1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT		0x6>;	/* SODIMM 19 */
+	};
+
+	pinctrl_pwm_2: pwm2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x6>;	/* SODIMM 15 */
+	};
+
+	pinctrl_pwm_3: pwm3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT			0x6>;	/* SODIMM 16 */
+	};
+
+	/* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM1_OUT */
+	pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsihpdgpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x184>;	/* SODIMM 19 */
+	};
+
+	pinctrl_reg_eth: regethgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x184>;	/* PMIC_EN_ETH */
+	};
+
+	pinctrl_reg_usb1_en: regusb1engrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x184>;	/* SODIMM 155 */
+	};
+
+	pinctrl_reg_usb2_en: regusb2engrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x184>;	/* SODIMM 185 */
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC		0xd6>,	/* SODIMM 32 */
+			<MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK		0xd6>,	/* SODIMM 30 */
+			<MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK		0xd6>,	/* SODIMM 38 */
+			<MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0		0xd6>,	/* SODIMM 36 */
+			<MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0		0xd6>;	/* SODIMM 34 */
+	};
+
+	pinctrl_sai5: sai5grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0		0xd6>,	/* SODIMM 48 */
+			<MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC		0xd6>,	/* SODIMM 44 */
+			<MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK		0xd6>,	/* SODIMM 42 */
+			<MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0		0xd6>;	/* SODIMM 46 */
+	};
+
+	/* control signal for optional ATTPM20P or SE050 */
+	pinctrl_pmic_tpm_ena: pmictpmenagrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x1c4>;	/* PMIC_TPM_ENA */
+	};
+
+	pinctrl_tsp: tspgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6		0x140>,	/* SODIMM 148 */
+			<MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7		0x140>,	/* SODIMM 152 */
+			<MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8		0x140>,	/* SODIMM 154 */
+			<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x140>,	/* SODIMM 179 */
+			<MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x140>;	/* SODIMM 150 */
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x1c4>,	/* SODIMM 149 */
+			<MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x1c4>;	/* SODIMM 147 */
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x1c4>,	/* SODIMM 129 */
+			<MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x1c4>,	/* SODIMM 131 */
+			<MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x1c4>,	/* SODIMM 133 */
+			<MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x1c4>;	/* SODIMM 135 */
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX		0x1c4>,	/* SODIMM 137 */
+			<MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX		0x1c4>,	/* SODIMM 139 */
+			<MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x1c4>,	/* SODIMM 141 */
+			<MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x1c4>;	/* SODIMM 143 */
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x1c4>,	/* SODIMM 151 */
+			<MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x1c4>;	/* SODIMM 153 */
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x190>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196>;
+	};
+
+	pinctrl_usdhc2_cd: usdhc2cdgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x1c4>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_pwr_en: usdhc2pwrengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5		0x184>;	/* SODIMM 76 */
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x190>,	/* SODIMM 78 */
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0>,	/* SODIMM 74 */
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0>,	/* SODIMM 80 */
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0>,	/* SODIMM 82 */
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0>,	/* SODIMM 70 */
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0>,	/* SODIMM 72 */
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194>,
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196>,
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6>,
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6>,
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0>;
+	};
+
+	/* On-module Wi-Fi/BT or type specific SDHC interface */
+	/* (e.g. on X52 extension slot of Verdin Development Board) */
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x190>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d0>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d0>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d6>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d6>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6>;	/* PMIC_WDI */
+	};
+
+	pinctrl_wifi_ctrl: wifictrlgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x1c4>,	/* WIFI_WKUP_BT */
+			<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x1c4>,	/* WIFI_W_WKUP_HOST */
+			<MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x1c4>;	/* WIFI_WKUP_WLAN */
+	};
+
+	pinctrl_wifi_i2s: bti2sgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_RXD4_SAI6_TX_BCLK		0xd6>,	/* WIFI_TX_BCLK */
+			<MX8MM_IOMUXC_SAI1_RXD5_SAI6_TX_DATA0		0xd6>,	/* WIFI_TX_DATA0 */
+			<MX8MM_IOMUXC_SAI1_RXD6_SAI6_TX_SYNC		0xd6>,	/* WIFI_TX_SYNC */
+			<MX8MM_IOMUXC_SAI1_TXD5_SAI6_RX_DATA0		0xd6>;	/* WIFI_RX_DATA0 */
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x184>;	/* PMIC_EN_WIFI */
+	};
+};
-- 
2.33.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 03/11] arm64: defconfig: enable taskstats configuration

[Krzysztof Kozlowski]

On 14/01/2022 15:14, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Enable CONFIG_TASKSTATS which is required for CONFIG_TASK_XACCT (and
> subsequently CONFIG_TASK_IO_ACCOUNTING). Previously, taskstats got
> pulled in by KVM but that got changed in commit 63b3f96e1a98
> ("kvm: Select SCHED_INFO instead of TASK_DELAY_ACCT").
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - New patch following full defconfig analysis as requested by Krzysztof.
> 

Nice!

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

Re: [PATCH v2 03/11] arm64: defconfig: enable taskstats configuration

[Krzysztof Kozlowski]

On 14/01/2022 15:14, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Enable CONFIG_TASKSTATS which is required for CONFIG_TASK_XACCT (and
> subsequently CONFIG_TASK_IO_ACCOUNTING). Previously, taskstats got
> pulled in by KVM but that got changed in commit 63b3f96e1a98
> ("kvm: Select SCHED_INFO instead of TASK_DELAY_ACCT").
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - New patch following full defconfig analysis as requested by Krzysztof.
> 

Nice!

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
> Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
> changed it to no longer being enabled by default.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - New patch following full defconfig analysis as requested by Krzysztof.
> 

Good finding! The question is whether we actually need PCIe AER...

Best regards,
Krzysztof

Re: [PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
> Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
> changed it to no longer being enabled by default.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - New patch following full defconfig analysis as requested by Krzysztof.
> 

Good finding! The question is whether we actually need PCIe AER...

Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 06/11] arm64: defconfig: enable bpf/cgroup firewalling

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> This avoids the following systemd warning:
> 
> [    2.618538] systemd[1]: system-getty.slice: unit configures an IP
>  firewall, but the local system does not support BPF/cgroup firewalling.
> [    2.630916] systemd[1]: (This warning is only shown for the first
>  unit using IP firewalling.)
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Acked-by: Song Liu <songliubraving@fb.com>
> 
> ---
> 
> Changes in v2:
> - Add Song's acked-by tag.
> 
>  arch/arm64/configs/defconfig | 2 ++
>  1 file changed, 2 insertions(+)
> 

Make sense.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

Re: [PATCH v2 06/11] arm64: defconfig: enable bpf/cgroup firewalling

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> This avoids the following systemd warning:
> 
> [    2.618538] systemd[1]: system-getty.slice: unit configures an IP
>  firewall, but the local system does not support BPF/cgroup firewalling.
> [    2.630916] systemd[1]: (This warning is only shown for the first
>  unit using IP firewalling.)
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Acked-by: Song Liu <songliubraving@fb.com>
> 
> ---
> 
> Changes in v2:
> - Add Song's acked-by tag.
> 
>  arch/arm64/configs/defconfig | 2 ++
>  1 file changed, 2 insertions(+)
> 

Make sense.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 08/11] arm64: defconfig: build r8169 as a module

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Build Realtek Gigabit Ethernet driver as a module.
> 
> Network cards based on chipsets this driver supports are ubiquitous both
> in regular PCIe as well as mini-PCIe and nowadays even various M.2
> formats. It is therefore a suitable card to be used for any kind of PCIe
> and/or Gigabit Ethernet testing. As it is not designed in, just enabling
> it as a module seems most suitable.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Explain why enabling it may be a good idea as requested by Krzysztof.
> 
>  arch/arm64/configs/defconfig | 1 +
>  1 file changed, 1 insertion(+)
> 


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

Re: [PATCH v2 08/11] arm64: defconfig: build r8169 as a module

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Build Realtek Gigabit Ethernet driver as a module.
> 
> Network cards based on chipsets this driver supports are ubiquitous both
> in regular PCIe as well as mini-PCIe and nowadays even various M.2
> formats. It is therefore a suitable card to be used for any kind of PCIe
> and/or Gigabit Ethernet testing. As it is not designed in, just enabling
> it as a module seems most suitable.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Explain why enabling it may be a good idea as requested by Krzysztof.
> 
>  arch/arm64/configs/defconfig | 1 +
>  1 file changed, 1 insertion(+)
> 


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 08/11] arm64: defconfig: build r8169 as a module

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Build Realtek Gigabit Ethernet driver as a module.
> 
> Network cards based on chipsets this driver supports are ubiquitous both
> in regular PCIe as well as mini-PCIe and nowadays even various M.2
> formats. It is therefore a suitable card to be used for any kind of PCIe
> and/or Gigabit Ethernet testing. As it is not designed in, just enabling
> it as a module seems most suitable.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Explain why enabling it may be a good idea as requested by Krzysztof.
> 
>  arch/arm64/configs/defconfig | 1 +
>  1 file changed, 1 insertion(+)
> 


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

Re: [PATCH v2 08/11] arm64: defconfig: build r8169 as a module

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Build Realtek Gigabit Ethernet driver as a module.
> 
> Network cards based on chipsets this driver supports are ubiquitous both
> in regular PCIe as well as mini-PCIe and nowadays even various M.2
> formats. It is therefore a suitable card to be used for any kind of PCIe
> and/or Gigabit Ethernet testing. As it is not designed in, just enabling
> it as a module seems most suitable.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Explain why enabling it may be a good idea as requested by Krzysztof.
> 
>  arch/arm64/configs/defconfig | 1 +
>  1 file changed, 1 insertion(+)
> 


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 09/11] arm64: defconfig: enable verdin-imx8mm relevant drivers as modules

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Enable various drivers which support peripherals as found on the
> Verdin iMX8M Mini et al. computer/system on modules:
> 
> - CONFIG_CAN_MCP251XFD
> At least one Microchip MCP2518FDT SPI CAN controller which this driver
> also supports may be found on the Verdin iMX8M Mini computer/system on
> module.
> 
> - CONFIG_BT_HCIUART_MRVL, CONFIG_BT_MRVL, CONFIG_BT_MRVL_SDIO and
>   CONFIG_MWIFIEX_SDIO
> The AzureWave AW-CM276NF which these Bluetooth and Wi-Fi drivers also
> support may be found on the Verdin iMX8M Mini (as well as the Apalis
> iMX8, Colibri iMX8X and Verdin iMX8M Plus for that matter) computer/
> system on module.
> 
> - CONFIG_SENSORS_LM75
> The TI TMP75C temperature sensor which this driver also supports may be
> found on the Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for
> that matter) computer/system on module.
> 
> - CONFIG_SND_SOC_NAU8822
> The Nuvoton Technology Corporation (NTC) NAU88C22YG which this driver
> also supports may be found on the Verdin Development Board a carrier
> board for the Verdin family of computer/system on module which the
> Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
> may be mated in.
> 
> - CONFIG_TI_ADS1015
> The TLA2024 ADC which this driver also supports may be found on the
> Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
> computer/system on module.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Explain why enabling these may make sense and squash them relevant
>   changes as requested by Krzysztof.
> 

Thanks, this is a nice explanation.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

Re: [PATCH v2 09/11] arm64: defconfig: enable verdin-imx8mm relevant drivers as modules

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Enable various drivers which support peripherals as found on the
> Verdin iMX8M Mini et al. computer/system on modules:
> 
> - CONFIG_CAN_MCP251XFD
> At least one Microchip MCP2518FDT SPI CAN controller which this driver
> also supports may be found on the Verdin iMX8M Mini computer/system on
> module.
> 
> - CONFIG_BT_HCIUART_MRVL, CONFIG_BT_MRVL, CONFIG_BT_MRVL_SDIO and
>   CONFIG_MWIFIEX_SDIO
> The AzureWave AW-CM276NF which these Bluetooth and Wi-Fi drivers also
> support may be found on the Verdin iMX8M Mini (as well as the Apalis
> iMX8, Colibri iMX8X and Verdin iMX8M Plus for that matter) computer/
> system on module.
> 
> - CONFIG_SENSORS_LM75
> The TI TMP75C temperature sensor which this driver also supports may be
> found on the Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for
> that matter) computer/system on module.
> 
> - CONFIG_SND_SOC_NAU8822
> The Nuvoton Technology Corporation (NTC) NAU88C22YG which this driver
> also supports may be found on the Verdin Development Board a carrier
> board for the Verdin family of computer/system on module which the
> Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
> may be mated in.
> 
> - CONFIG_TI_ADS1015
> The TLA2024 ADC which this driver also supports may be found on the
> Verdin iMX8M Mini (as well as the Verdin iMX8M Plus for that matter)
> computer/system on module.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Explain why enabling these may make sense and squash them relevant
>   changes as requested by Krzysztof.
> 

Thanks, this is a nice explanation.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 11/11] arm64: dts: freescale: add initial support for verdin imx8m mini

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> This patch adds the device tree to support Toradex Verdin iMX8M Mini a
> computer on module which can be used on different carrier boards.
> 
> The module consists of an NXP i.MX 8M Mini family SoC (either i.MX 8M
> Mini Quad or 8M Mini DualLite), a PCA9450A PMIC, a Gigabit Ethernet PHY,
> 1 or 2 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
> RX8130 RTC, an optional SPI CAN controller plus an optional Bluetooth/
> Wi-Fi module.
> 
> Anything that is not self-contained on the module is disabled by
> default.
> 
> The device tree for the Dahlia includes the module's device tree and
> enables the supported peripherals of the carrier board.
> 
> The device tree for the Verdin Development Board includes the module's
> device tree as well as the Dahlia one as it is a superset and supports
> almost all peripherals available.
> 
> So far there is no display functionality supported at all but basic
> console UART, USB host, eMMC and Ethernet and PCIe functionality work
> fine.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Remove bootargs which will be filled in by the bootloader as requested
>   by Krzysztof.
> - Remove the previously #ifdefed-out spi-nor as requested by Krzysztof.
> - Fix capitalisation in cover-letter.
> 

Thanks for the changes.

Looks, good but I did not perform review thorough enough to give a
Reviewed-by tag, so let it be just:

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

Re: [PATCH v2 11/11] arm64: dts: freescale: add initial support for verdin imx8m mini

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> This patch adds the device tree to support Toradex Verdin iMX8M Mini a
> computer on module which can be used on different carrier boards.
> 
> The module consists of an NXP i.MX 8M Mini family SoC (either i.MX 8M
> Mini Quad or 8M Mini DualLite), a PCA9450A PMIC, a Gigabit Ethernet PHY,
> 1 or 2 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
> RX8130 RTC, an optional SPI CAN controller plus an optional Bluetooth/
> Wi-Fi module.
> 
> Anything that is not self-contained on the module is disabled by
> default.
> 
> The device tree for the Dahlia includes the module's device tree and
> enables the supported peripherals of the carrier board.
> 
> The device tree for the Verdin Development Board includes the module's
> device tree as well as the Dahlia one as it is a superset and supports
> almost all peripherals available.
> 
> So far there is no display functionality supported at all but basic
> console UART, USB host, eMMC and Ethernet and PCIe functionality work
> fine.
> 
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> ---
> 
> Changes in v2:
> - Remove bootargs which will be filled in by the bootloader as requested
>   by Krzysztof.
> - Remove the previously #ifdefed-out spi-nor as requested by Krzysztof.
> - Fix capitalisation in cover-letter.
> 

Thanks for the changes.

Looks, good but I did not perform review thorough enough to give a
Reviewed-by tag, so let it be just:

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Run "make defconfig; make savedefconfig" to rebuild defconfig.
> 
> This re-ordered the following configuration options:
> 
> CONFIG_BPF_JIT=y
> CONFIG_ARM_SCMI_PROTOCOL=y
> CONFIG_ARM_SCPI_PROTOCOL=y
> CONFIG_RASPBERRYPI_FIRMWARE=y
> CONFIG_INTEL_STRATIX10_SERVICE=y
> CONFIG_INTEL_STRATIX10_RSU=m
> CONFIG_EFI_CAPSULE_LOADER=y
> CONFIG_IMX_SCU=y
> CONFIG_IMX_SCU_PD=y
> CONFIG_CAN_FLEXCAN=m
> CONFIG_PCIE_LAYERSCAPE_GEN4=y
> CONFIG_MTK_DEVAPC=m
> CONFIG_SPI_CADENCE_QUADSPI=y
> CONFIG_MDIO_BUS_MUX_MMIOREG=y
> CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
> CONFIG_MESON_GXL_PHY=m
> CONFIG_QCOM_CPR=y
> CONFIG_ROCKCHIP_IODOMAIN=y
> CONFIG_SENSORS_ARM_SCMI=y
> CONFIG_QORIQ_THERMAL=m
> CONFIG_SUN8I_THERMAL=y
> CONFIG_TEGRA_BPMP_THERMAL=m
> CONFIG_ARM_SMC_WATCHDOG=y
> CONFIG_VIDEO_QCOM_CAMSS=m
> CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
> CONFIG_DRM_NWL_MIPI_DSI=m
> CONFIG_DRM_LONTIUM_LT9611UXC=m
> CONFIG_SND_SOC_IMX_AUDMIX=m
> CONFIG_TYPEC_HD3SS3220=m
> CONFIG_COMMON_CLK_SCMI=y
> CONFIG_IPQ_GCC_8074=y
> CONFIG_SM_DISPCC_8250=y
> CONFIG_QCOM_WCNSS_CTRL=m
> CONFIG_ARCH_R8A774A1=y
> CONFIG_ARCH_R8A774B1=y
> CONFIG_ARCH_R8A774C0=y
> CONFIG_ARCH_R8A774E1=y
> CONFIG_ARCH_R8A77995=y
> CONFIG_ARCH_R8A77990=y
> CONFIG_ARCH_R8A77965=y
> CONFIG_ARCH_R8A77970=y
> CONFIG_HISI_PMU=y
> CONFIG_QCOM_QFPROM=y
> CONFIG_MUX_MMIO=y

Thanks for the changes.
The best would be to have a separate patch only for re-ordering.

> 
> And dropped the following configuration options which are nowaday's
> already enabled (resp. disabled) by default:
> 
> CONFIG_MEMCG_SWAP=y
> CONFIG_SECCOMP=y

Is it? I tried now on next-20220114 and it is still user-selectable and
not chosen by anything.

> CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
> CONFIG_QCOM_SCM=y
> # CONFIG_BT_HS is not set
> CONFIG_FSL_MC_BUS=y
> CONFIG_MEDIA_CONTROLLER=y
> CONFIG_VIDEO_V4L2_SUBDEV_API=y
> CONFIG_SND_SOC_FSL_SAI=m
> CONFIG_USB_CONN_GPIO=m
> CONFIG_USB_XHCI_PCI=m
> CONFIG_MFD_CROS_EC_DEV=y
> CONFIG_COMMON_CLK_ZYNQMP=y
> CONFIG_SDM_GCC_845=y
> CONFIG_SM_GCC_8150=y
> CONFIG_SM_GCC_8250=y
> CONFIG_SLIMBUS=m
> CONFIG_INTERCONNECT=y
> CONFIG_CONFIGFS_FS=y

All three above are still user-selectable, so please leave them. It is
redundant, but there is no guarantee that something selecting a
user-visible symbol will stop selecting it. IOW, user-visible symbols
should be still chosen by defconfigs if they really want them.

See for example commit a2315d3aea59 ("ARM: exynos_defconfig: Restore
debugfs support") for rationale why we need to keep them.


Best regards,
Krzysztof

Re: [PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Krzysztof Kozlowski]

On 14/01/2022 15:15, Marcel Ziswiler wrote:
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> 
> Run "make defconfig; make savedefconfig" to rebuild defconfig.
> 
> This re-ordered the following configuration options:
> 
> CONFIG_BPF_JIT=y
> CONFIG_ARM_SCMI_PROTOCOL=y
> CONFIG_ARM_SCPI_PROTOCOL=y
> CONFIG_RASPBERRYPI_FIRMWARE=y
> CONFIG_INTEL_STRATIX10_SERVICE=y
> CONFIG_INTEL_STRATIX10_RSU=m
> CONFIG_EFI_CAPSULE_LOADER=y
> CONFIG_IMX_SCU=y
> CONFIG_IMX_SCU_PD=y
> CONFIG_CAN_FLEXCAN=m
> CONFIG_PCIE_LAYERSCAPE_GEN4=y
> CONFIG_MTK_DEVAPC=m
> CONFIG_SPI_CADENCE_QUADSPI=y
> CONFIG_MDIO_BUS_MUX_MMIOREG=y
> CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
> CONFIG_MESON_GXL_PHY=m
> CONFIG_QCOM_CPR=y
> CONFIG_ROCKCHIP_IODOMAIN=y
> CONFIG_SENSORS_ARM_SCMI=y
> CONFIG_QORIQ_THERMAL=m
> CONFIG_SUN8I_THERMAL=y
> CONFIG_TEGRA_BPMP_THERMAL=m
> CONFIG_ARM_SMC_WATCHDOG=y
> CONFIG_VIDEO_QCOM_CAMSS=m
> CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
> CONFIG_DRM_NWL_MIPI_DSI=m
> CONFIG_DRM_LONTIUM_LT9611UXC=m
> CONFIG_SND_SOC_IMX_AUDMIX=m
> CONFIG_TYPEC_HD3SS3220=m
> CONFIG_COMMON_CLK_SCMI=y
> CONFIG_IPQ_GCC_8074=y
> CONFIG_SM_DISPCC_8250=y
> CONFIG_QCOM_WCNSS_CTRL=m
> CONFIG_ARCH_R8A774A1=y
> CONFIG_ARCH_R8A774B1=y
> CONFIG_ARCH_R8A774C0=y
> CONFIG_ARCH_R8A774E1=y
> CONFIG_ARCH_R8A77995=y
> CONFIG_ARCH_R8A77990=y
> CONFIG_ARCH_R8A77965=y
> CONFIG_ARCH_R8A77970=y
> CONFIG_HISI_PMU=y
> CONFIG_QCOM_QFPROM=y
> CONFIG_MUX_MMIO=y

Thanks for the changes.
The best would be to have a separate patch only for re-ordering.

> 
> And dropped the following configuration options which are nowaday's
> already enabled (resp. disabled) by default:
> 
> CONFIG_MEMCG_SWAP=y
> CONFIG_SECCOMP=y

Is it? I tried now on next-20220114 and it is still user-selectable and
not chosen by anything.

> CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
> CONFIG_QCOM_SCM=y
> # CONFIG_BT_HS is not set
> CONFIG_FSL_MC_BUS=y
> CONFIG_MEDIA_CONTROLLER=y
> CONFIG_VIDEO_V4L2_SUBDEV_API=y
> CONFIG_SND_SOC_FSL_SAI=m
> CONFIG_USB_CONN_GPIO=m
> CONFIG_USB_XHCI_PCI=m
> CONFIG_MFD_CROS_EC_DEV=y
> CONFIG_COMMON_CLK_ZYNQMP=y
> CONFIG_SDM_GCC_845=y
> CONFIG_SM_GCC_8150=y
> CONFIG_SM_GCC_8250=y
> CONFIG_SLIMBUS=m
> CONFIG_INTERCONNECT=y
> CONFIG_CONFIGFS_FS=y

All three above are still user-selectable, so please leave them. It is
redundant, but there is no guarantee that something selecting a
user-visible symbol will stop selecting it. IOW, user-visible symbols
should be still chosen by defconfigs if they really want them.

See for example commit a2315d3aea59 ("ARM: exynos_defconfig: Restore
debugfs support") for rationale why we need to keep them.


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 02/11] dt-bindings: gpio: fix gpio-hog example

[Linus Walleij]

On Fri, Jan 14, 2022 at 3:15 PM Marcel Ziswiler <marcel@ziswiler.com> wrote:

> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>
> Even if this is no yaml yet at least fix the example to be compliant to
> later schema as e.g. found in gpio-pca95xx.yaml, fairchild,74hc595.yaml
> and gpio/fsl-imx-gpio.yaml.
>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Acked-by: Rob Herring <robh@kernel.org>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

Re: [PATCH v2 02/11] dt-bindings: gpio: fix gpio-hog example

[Linus Walleij]

On Fri, Jan 14, 2022 at 3:15 PM Marcel Ziswiler <marcel@ziswiler.com> wrote:

> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>
> Even if this is no yaml yet at least fix the example to be compliant to
> later schema as e.g. found in gpio-pca95xx.yaml, fairchild,74hc595.yaml
> and gpio/fsl-imx-gpio.yaml.
>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Acked-by: Rob Herring <robh@kernel.org>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Marcel Ziswiler]

On Sat, 2022-01-15 at 17:45 +0100, Krzysztof Kozlowski wrote:
> On 14/01/2022 15:15, Marcel Ziswiler wrote:
> > From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
> > Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
> > changed it to no longer being enabled by default.
> > 
> > Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > ---
> > 
> > Changes in v2:
> > - New patch following full defconfig analysis as requested by Krzysztof.
> > 
> 
> Good finding! The question is whether we actually need PCIe AER...

Yes, however, why else would we have explicitly enabled CONFIG_ACPI_APEI_PCIEAER?

> Best regards,
> Krzysztof

Re: [PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Marcel Ziswiler]

On Sat, 2022-01-15 at 17:45 +0100, Krzysztof Kozlowski wrote:
> On 14/01/2022 15:15, Marcel Ziswiler wrote:
> > From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
> > Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
> > changed it to no longer being enabled by default.
> > 
> > Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > ---
> > 
> > Changes in v2:
> > - New patch following full defconfig analysis as requested by Krzysztof.
> > 
> 
> Good finding! The question is whether we actually need PCIe AER...

Yes, however, why else would we have explicitly enabled CONFIG_ACPI_APEI_PCIEAER?

> Best regards,
> Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Krzysztof Kozlowski]

On 17/01/2022 12:45, Marcel Ziswiler wrote:
> On Sat, 2022-01-15 at 17:45 +0100, Krzysztof Kozlowski wrote:
>> On 14/01/2022 15:15, Marcel Ziswiler wrote:
>>> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>>>
>>> Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
>>> Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
>>> changed it to no longer being enabled by default.
>>>
>>> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>>>
>>> ---
>>>
>>> Changes in v2:
>>> - New patch following full defconfig analysis as requested by Krzysztof.
>>>
>>
>> Good finding! The question is whether we actually need PCIe AER...
> 
> Yes, however, why else would we have explicitly enabled CONFIG_ACPI_APEI_PCIEAER?

Right, I missed that it is mentioned in defconfig.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

Re: [PATCH v2 04/11] arm64: defconfig: enable pcieaer configuration

[Krzysztof Kozlowski]

On 17/01/2022 12:45, Marcel Ziswiler wrote:
> On Sat, 2022-01-15 at 17:45 +0100, Krzysztof Kozlowski wrote:
>> On 14/01/2022 15:15, Marcel Ziswiler wrote:
>>> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>>>
>>> Enable CONFIG_PCIEAER which is required for CONFIG_ACPI_APEI_PCIEAER.
>>> Commit 8c8ff55b4da7 ("PCI/AER: Don't select CONFIG_PCIEAER by default")
>>> changed it to no longer being enabled by default.
>>>
>>> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>>>
>>> ---
>>>
>>> Changes in v2:
>>> - New patch following full defconfig analysis as requested by Krzysztof.
>>>
>>
>> Good finding! The question is whether we actually need PCIe AER...
> 
> Yes, however, why else would we have explicitly enabled CONFIG_ACPI_APEI_PCIEAER?

Right, I missed that it is mentioned in defconfig.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>


Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Marcel Ziswiler]

On Sat, 2022-01-15 at 18:02 +0100, Krzysztof Kozlowski wrote:
> On 14/01/2022 15:15, Marcel Ziswiler wrote:
> > From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > Run "make defconfig; make savedefconfig" to rebuild defconfig.
> > 
> > This re-ordered the following configuration options:
> > 
> > CONFIG_BPF_JIT=y
> > CONFIG_ARM_SCMI_PROTOCOL=y
> > CONFIG_ARM_SCPI_PROTOCOL=y
> > CONFIG_RASPBERRYPI_FIRMWARE=y
> > CONFIG_INTEL_STRATIX10_SERVICE=y
> > CONFIG_INTEL_STRATIX10_RSU=m
> > CONFIG_EFI_CAPSULE_LOADER=y
> > CONFIG_IMX_SCU=y
> > CONFIG_IMX_SCU_PD=y
> > CONFIG_CAN_FLEXCAN=m
> > CONFIG_PCIE_LAYERSCAPE_GEN4=y
> > CONFIG_MTK_DEVAPC=m
> > CONFIG_SPI_CADENCE_QUADSPI=y
> > CONFIG_MDIO_BUS_MUX_MMIOREG=y
> > CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
> > CONFIG_MESON_GXL_PHY=m
> > CONFIG_QCOM_CPR=y
> > CONFIG_ROCKCHIP_IODOMAIN=y
> > CONFIG_SENSORS_ARM_SCMI=y
> > CONFIG_QORIQ_THERMAL=m
> > CONFIG_SUN8I_THERMAL=y
> > CONFIG_TEGRA_BPMP_THERMAL=m
> > CONFIG_ARM_SMC_WATCHDOG=y
> > CONFIG_VIDEO_QCOM_CAMSS=m
> > CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
> > CONFIG_DRM_NWL_MIPI_DSI=m
> > CONFIG_DRM_LONTIUM_LT9611UXC=m
> > CONFIG_SND_SOC_IMX_AUDMIX=m
> > CONFIG_TYPEC_HD3SS3220=m
> > CONFIG_COMMON_CLK_SCMI=y
> > CONFIG_IPQ_GCC_8074=y
> > CONFIG_SM_DISPCC_8250=y
> > CONFIG_QCOM_WCNSS_CTRL=m
> > CONFIG_ARCH_R8A774A1=y
> > CONFIG_ARCH_R8A774B1=y
> > CONFIG_ARCH_R8A774C0=y
> > CONFIG_ARCH_R8A774E1=y
> > CONFIG_ARCH_R8A77995=y
> > CONFIG_ARCH_R8A77990=y
> > CONFIG_ARCH_R8A77965=y
> > CONFIG_ARCH_R8A77970=y
> > CONFIG_HISI_PMU=y
> > CONFIG_QCOM_QFPROM=y
> > CONFIG_MUX_MMIO=y
> 
> Thanks for the changes.
> The best would be to have a separate patch only for re-ordering.

Yes, from a review perspective that makes sense. Will do so in v3.

> > And dropped the following configuration options which are nowaday's
> > already enabled (resp. disabled) by default:
> > 
> > CONFIG_MEMCG_SWAP=y
> > CONFIG_SECCOMP=y
> 
> Is it? I tried now on next-20220114 and it is still user-selectable and
> not chosen by anything.

Hm, strange. I guess, it is due to this whole patch series, given its i.MX main focus, being based on Shawn's
for-next branch. Maybe for such defconfig changes it would be better to base them on something else? Not sure,
who will ultimately pull such changes. Any suggestion?

> > CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
> > CONFIG_QCOM_SCM=y
> > # CONFIG_BT_HS is not set
> > CONFIG_FSL_MC_BUS=y
> > CONFIG_MEDIA_CONTROLLER=y
> > CONFIG_VIDEO_V4L2_SUBDEV_API=y
> > CONFIG_SND_SOC_FSL_SAI=m
> > CONFIG_USB_CONN_GPIO=m
> > CONFIG_USB_XHCI_PCI=m
> > CONFIG_MFD_CROS_EC_DEV=y
> > CONFIG_COMMON_CLK_ZYNQMP=y
> > CONFIG_SDM_GCC_845=y
> > CONFIG_SM_GCC_8150=y
> > CONFIG_SM_GCC_8250=y
> > CONFIG_SLIMBUS=m
> > CONFIG_INTERCONNECT=y
> > CONFIG_CONFIGFS_FS=y
> 
> All three above are still user-selectable, so please leave them. It is
> redundant, but there is no guarantee that something selecting a
> user-visible symbol will stop selecting it. IOW, user-visible symbols
> should be still chosen by defconfigs if they really want them.

Well, but even if they are already enabled anyway? What is the point of savedefconfig then resp. you are saying
that the commited defconfigs should not be generated using savedefconfig? That sounds rather confusing to me.

> See for example commit a2315d3aea59 ("ARM: exynos_defconfig: Restore
> debugfs support") for rationale why we need to keep them.

Okay, I see what you mean as in relation to above mentioned commit but then any change to Kconfig dependencies
can ultimately change the behaviour of previous configs unless they are complete ones (or were just lucky to
include whatever stuff that changed). But how should one now know which of them zillions of user-selectable
options should be added to such "more robust" defconfigs?

I suggest a better approach might be to have some CI which validates defconfig changes. That way one could
easily track stuff disappearing and could at that point explicitly enable it again.

> Best regards,
> Krzysztof

Cheers

Marcel

Re: [PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Marcel Ziswiler]

On Sat, 2022-01-15 at 18:02 +0100, Krzysztof Kozlowski wrote:
> On 14/01/2022 15:15, Marcel Ziswiler wrote:
> > From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > 
> > Run "make defconfig; make savedefconfig" to rebuild defconfig.
> > 
> > This re-ordered the following configuration options:
> > 
> > CONFIG_BPF_JIT=y
> > CONFIG_ARM_SCMI_PROTOCOL=y
> > CONFIG_ARM_SCPI_PROTOCOL=y
> > CONFIG_RASPBERRYPI_FIRMWARE=y
> > CONFIG_INTEL_STRATIX10_SERVICE=y
> > CONFIG_INTEL_STRATIX10_RSU=m
> > CONFIG_EFI_CAPSULE_LOADER=y
> > CONFIG_IMX_SCU=y
> > CONFIG_IMX_SCU_PD=y
> > CONFIG_CAN_FLEXCAN=m
> > CONFIG_PCIE_LAYERSCAPE_GEN4=y
> > CONFIG_MTK_DEVAPC=m
> > CONFIG_SPI_CADENCE_QUADSPI=y
> > CONFIG_MDIO_BUS_MUX_MMIOREG=y
> > CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
> > CONFIG_MESON_GXL_PHY=m
> > CONFIG_QCOM_CPR=y
> > CONFIG_ROCKCHIP_IODOMAIN=y
> > CONFIG_SENSORS_ARM_SCMI=y
> > CONFIG_QORIQ_THERMAL=m
> > CONFIG_SUN8I_THERMAL=y
> > CONFIG_TEGRA_BPMP_THERMAL=m
> > CONFIG_ARM_SMC_WATCHDOG=y
> > CONFIG_VIDEO_QCOM_CAMSS=m
> > CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
> > CONFIG_DRM_NWL_MIPI_DSI=m
> > CONFIG_DRM_LONTIUM_LT9611UXC=m
> > CONFIG_SND_SOC_IMX_AUDMIX=m
> > CONFIG_TYPEC_HD3SS3220=m
> > CONFIG_COMMON_CLK_SCMI=y
> > CONFIG_IPQ_GCC_8074=y
> > CONFIG_SM_DISPCC_8250=y
> > CONFIG_QCOM_WCNSS_CTRL=m
> > CONFIG_ARCH_R8A774A1=y
> > CONFIG_ARCH_R8A774B1=y
> > CONFIG_ARCH_R8A774C0=y
> > CONFIG_ARCH_R8A774E1=y
> > CONFIG_ARCH_R8A77995=y
> > CONFIG_ARCH_R8A77990=y
> > CONFIG_ARCH_R8A77965=y
> > CONFIG_ARCH_R8A77970=y
> > CONFIG_HISI_PMU=y
> > CONFIG_QCOM_QFPROM=y
> > CONFIG_MUX_MMIO=y
> 
> Thanks for the changes.
> The best would be to have a separate patch only for re-ordering.

Yes, from a review perspective that makes sense. Will do so in v3.

> > And dropped the following configuration options which are nowaday's
> > already enabled (resp. disabled) by default:
> > 
> > CONFIG_MEMCG_SWAP=y
> > CONFIG_SECCOMP=y
> 
> Is it? I tried now on next-20220114 and it is still user-selectable and
> not chosen by anything.

Hm, strange. I guess, it is due to this whole patch series, given its i.MX main focus, being based on Shawn's
for-next branch. Maybe for such defconfig changes it would be better to base them on something else? Not sure,
who will ultimately pull such changes. Any suggestion?

> > CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
> > CONFIG_QCOM_SCM=y
> > # CONFIG_BT_HS is not set
> > CONFIG_FSL_MC_BUS=y
> > CONFIG_MEDIA_CONTROLLER=y
> > CONFIG_VIDEO_V4L2_SUBDEV_API=y
> > CONFIG_SND_SOC_FSL_SAI=m
> > CONFIG_USB_CONN_GPIO=m
> > CONFIG_USB_XHCI_PCI=m
> > CONFIG_MFD_CROS_EC_DEV=y
> > CONFIG_COMMON_CLK_ZYNQMP=y
> > CONFIG_SDM_GCC_845=y
> > CONFIG_SM_GCC_8150=y
> > CONFIG_SM_GCC_8250=y
> > CONFIG_SLIMBUS=m
> > CONFIG_INTERCONNECT=y
> > CONFIG_CONFIGFS_FS=y
> 
> All three above are still user-selectable, so please leave them. It is
> redundant, but there is no guarantee that something selecting a
> user-visible symbol will stop selecting it. IOW, user-visible symbols
> should be still chosen by defconfigs if they really want them.

Well, but even if they are already enabled anyway? What is the point of savedefconfig then resp. you are saying
that the commited defconfigs should not be generated using savedefconfig? That sounds rather confusing to me.

> See for example commit a2315d3aea59 ("ARM: exynos_defconfig: Restore
> debugfs support") for rationale why we need to keep them.

Okay, I see what you mean as in relation to above mentioned commit but then any change to Kconfig dependencies
can ultimately change the behaviour of previous configs unless they are complete ones (or were just lucky to
include whatever stuff that changed). But how should one now know which of them zillions of user-selectable
options should be added to such "more robust" defconfigs?

I suggest a better approach might be to have some CI which validates defconfig changes. That way one could
easily track stuff disappearing and could at that point explicitly enable it again.

> Best regards,
> Krzysztof

Cheers

Marcel
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Krzysztof Kozlowski]

On 17/01/2022 13:05, Marcel Ziswiler wrote:
> On Sat, 2022-01-15 at 18:02 +0100, Krzysztof Kozlowski wrote:
>> On 14/01/2022 15:15, Marcel Ziswiler wrote:
>>> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>>>
>>> Run "make defconfig; make savedefconfig" to rebuild defconfig.
>>>
>>> This re-ordered the following configuration options:
>>>
>>> CONFIG_BPF_JIT=y
>>> CONFIG_ARM_SCMI_PROTOCOL=y
>>> CONFIG_ARM_SCPI_PROTOCOL=y
>>> CONFIG_RASPBERRYPI_FIRMWARE=y
>>> CONFIG_INTEL_STRATIX10_SERVICE=y
>>> CONFIG_INTEL_STRATIX10_RSU=m
>>> CONFIG_EFI_CAPSULE_LOADER=y
>>> CONFIG_IMX_SCU=y
>>> CONFIG_IMX_SCU_PD=y
>>> CONFIG_CAN_FLEXCAN=m
>>> CONFIG_PCIE_LAYERSCAPE_GEN4=y
>>> CONFIG_MTK_DEVAPC=m
>>> CONFIG_SPI_CADENCE_QUADSPI=y
>>> CONFIG_MDIO_BUS_MUX_MMIOREG=y
>>> CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
>>> CONFIG_MESON_GXL_PHY=m
>>> CONFIG_QCOM_CPR=y
>>> CONFIG_ROCKCHIP_IODOMAIN=y
>>> CONFIG_SENSORS_ARM_SCMI=y
>>> CONFIG_QORIQ_THERMAL=m
>>> CONFIG_SUN8I_THERMAL=y
>>> CONFIG_TEGRA_BPMP_THERMAL=m
>>> CONFIG_ARM_SMC_WATCHDOG=y
>>> CONFIG_VIDEO_QCOM_CAMSS=m
>>> CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
>>> CONFIG_DRM_NWL_MIPI_DSI=m
>>> CONFIG_DRM_LONTIUM_LT9611UXC=m
>>> CONFIG_SND_SOC_IMX_AUDMIX=m
>>> CONFIG_TYPEC_HD3SS3220=m
>>> CONFIG_COMMON_CLK_SCMI=y
>>> CONFIG_IPQ_GCC_8074=y
>>> CONFIG_SM_DISPCC_8250=y
>>> CONFIG_QCOM_WCNSS_CTRL=m
>>> CONFIG_ARCH_R8A774A1=y
>>> CONFIG_ARCH_R8A774B1=y
>>> CONFIG_ARCH_R8A774C0=y
>>> CONFIG_ARCH_R8A774E1=y
>>> CONFIG_ARCH_R8A77995=y
>>> CONFIG_ARCH_R8A77990=y
>>> CONFIG_ARCH_R8A77965=y
>>> CONFIG_ARCH_R8A77970=y
>>> CONFIG_HISI_PMU=y
>>> CONFIG_QCOM_QFPROM=y
>>> CONFIG_MUX_MMIO=y
>>
>> Thanks for the changes.
>> The best would be to have a separate patch only for re-ordering.
> 
> Yes, from a review perspective that makes sense. Will do so in v3.
> 
>>> And dropped the following configuration options which are nowaday's
>>> already enabled (resp. disabled) by default:
>>>
>>> CONFIG_MEMCG_SWAP=y
>>> CONFIG_SECCOMP=y
>>
>> Is it? I tried now on next-20220114 and it is still user-selectable and
>> not chosen by anything.
> 
> Hm, strange. I guess, it is due to this whole patch series, given its i.MX main focus, being based on Shawn's
> for-next branch. Maybe for such defconfig changes it would be better to base them on something else? Not sure,
> who will ultimately pull such changes. Any suggestion?

I don't think there is a one nice solution, fit-for-all.

Consider a defconfig selecting FOO and BAR, plus Kconfig like:
config FOO
	depends on BAR

If you run savedefconfig on arm-soc next branch, there is a chance that
in parallel someone else will adjust the Kconfig in some other tree,
based on Linus' master. That person removes "depends on BAR" above and
notices that FOO is mentioned in defconfig, so no need to update defconfig.

However your savedefconfig commit will exactly remove the FOO from
defconfig, because there is no reason for it to be. After merging to
Linus - FOO is gone from defconfig.

Another approach - you base your savedefconfig on linux-next. This
should solve the problem above, except that such commit might not apply
on the maintainer's tree.

Therefore recommendation is to not run savedefconfig or run it very
carefully, for example explaining why each option is being removed. I
was doing it in the past, but it's quite time consuming:

https://lore.kernel.org/linux-arm-kernel/1500270596-22384-1-git-send-email-krzk@kernel.org/

and earlier set:
https://lore.kernel.org/linux-arm-kernel/20170608161049.12421-1-krzk@kernel.org/

> 
>>> CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
>>> CONFIG_QCOM_SCM=y
>>> # CONFIG_BT_HS is not set
>>> CONFIG_FSL_MC_BUS=y
>>> CONFIG_MEDIA_CONTROLLER=y
>>> CONFIG_VIDEO_V4L2_SUBDEV_API=y
>>> CONFIG_SND_SOC_FSL_SAI=m
>>> CONFIG_USB_CONN_GPIO=m
>>> CONFIG_USB_XHCI_PCI=m
>>> CONFIG_MFD_CROS_EC_DEV=y
>>> CONFIG_COMMON_CLK_ZYNQMP=y
>>> CONFIG_SDM_GCC_845=y
>>> CONFIG_SM_GCC_8150=y
>>> CONFIG_SM_GCC_8250=y
>>> CONFIG_SLIMBUS=m
>>> CONFIG_INTERCONNECT=y
>>> CONFIG_CONFIGFS_FS=y
>>
>> All three above are still user-selectable, so please leave them. It is
>> redundant, but there is no guarantee that something selecting a
>> user-visible symbol will stop selecting it. IOW, user-visible symbols
>> should be still chosen by defconfigs if they really want them.
> 
> Well, but even if they are already enabled anyway? What is the point of savedefconfig then resp. you are saying
> that the commited defconfigs should not be generated using savedefconfig? That sounds rather confusing to me.

Yes, it's confusing. savedefconfig is too aggressive - it strips
everything which is not strictly necessary now. However there is no
guarantee that current select of some option, thus stripped out that
option via savedefconfig, will stay there forever.

If CONFIG_XXX is not user-selectable, then when someone removes the
"select XXX", it *is expected* to modify the defconfigs to add back this
XXX.

However it turns out that some developers assume that there is no such
requirement of re-adding XXX to defconfig, if XXX was user-selectable in
the first place.


> 
>> See for example commit a2315d3aea59 ("ARM: exynos_defconfig: Restore
>> debugfs support") for rationale why we need to keep them.
> 
> Okay, I see what you mean as in relation to above mentioned commit but then any change to Kconfig dependencies
> can ultimately change the behaviour of previous configs unless they are complete ones (or were just lucky to
> include whatever stuff that changed). But how should one now know which of them zillions of user-selectable
> options should be added to such "more robust" defconfigs?

No clue... :) Except maybe do not remove existing ones.

> 
> I suggest a better approach might be to have some CI which validates defconfig changes. That way one could
> easily track stuff disappearing and could at that point explicitly enable it again.

Yes, that makes sense. One defines the expected symbols to have and CI
validates whether they are enabled. We have something like this (called
annotations) in our Ubuntu configs - we store a list of config options
were are interested in and detect when they change.

Another approach is to use specialized fragments.

The benefits of such solutions is that they also document why such
option was chosen in the first place (what I was also asking from your
patches here at beginning and thanks for fixing this).

Best regards,
Krzysztof

Re: [PATCH v2 05/11] arm64: defconfig: rebuild default configuration

[Krzysztof Kozlowski]

On 17/01/2022 13:05, Marcel Ziswiler wrote:
> On Sat, 2022-01-15 at 18:02 +0100, Krzysztof Kozlowski wrote:
>> On 14/01/2022 15:15, Marcel Ziswiler wrote:
>>> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>>>
>>> Run "make defconfig; make savedefconfig" to rebuild defconfig.
>>>
>>> This re-ordered the following configuration options:
>>>
>>> CONFIG_BPF_JIT=y
>>> CONFIG_ARM_SCMI_PROTOCOL=y
>>> CONFIG_ARM_SCPI_PROTOCOL=y
>>> CONFIG_RASPBERRYPI_FIRMWARE=y
>>> CONFIG_INTEL_STRATIX10_SERVICE=y
>>> CONFIG_INTEL_STRATIX10_RSU=m
>>> CONFIG_EFI_CAPSULE_LOADER=y
>>> CONFIG_IMX_SCU=y
>>> CONFIG_IMX_SCU_PD=y
>>> CONFIG_CAN_FLEXCAN=m
>>> CONFIG_PCIE_LAYERSCAPE_GEN4=y
>>> CONFIG_MTK_DEVAPC=m
>>> CONFIG_SPI_CADENCE_QUADSPI=y
>>> CONFIG_MDIO_BUS_MUX_MMIOREG=y
>>> CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
>>> CONFIG_MESON_GXL_PHY=m
>>> CONFIG_QCOM_CPR=y
>>> CONFIG_ROCKCHIP_IODOMAIN=y
>>> CONFIG_SENSORS_ARM_SCMI=y
>>> CONFIG_QORIQ_THERMAL=m
>>> CONFIG_SUN8I_THERMAL=y
>>> CONFIG_TEGRA_BPMP_THERMAL=m
>>> CONFIG_ARM_SMC_WATCHDOG=y
>>> CONFIG_VIDEO_QCOM_CAMSS=m
>>> CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
>>> CONFIG_DRM_NWL_MIPI_DSI=m
>>> CONFIG_DRM_LONTIUM_LT9611UXC=m
>>> CONFIG_SND_SOC_IMX_AUDMIX=m
>>> CONFIG_TYPEC_HD3SS3220=m
>>> CONFIG_COMMON_CLK_SCMI=y
>>> CONFIG_IPQ_GCC_8074=y
>>> CONFIG_SM_DISPCC_8250=y
>>> CONFIG_QCOM_WCNSS_CTRL=m
>>> CONFIG_ARCH_R8A774A1=y
>>> CONFIG_ARCH_R8A774B1=y
>>> CONFIG_ARCH_R8A774C0=y
>>> CONFIG_ARCH_R8A774E1=y
>>> CONFIG_ARCH_R8A77995=y
>>> CONFIG_ARCH_R8A77990=y
>>> CONFIG_ARCH_R8A77965=y
>>> CONFIG_ARCH_R8A77970=y
>>> CONFIG_HISI_PMU=y
>>> CONFIG_QCOM_QFPROM=y
>>> CONFIG_MUX_MMIO=y
>>
>> Thanks for the changes.
>> The best would be to have a separate patch only for re-ordering.
> 
> Yes, from a review perspective that makes sense. Will do so in v3.
> 
>>> And dropped the following configuration options which are nowaday's
>>> already enabled (resp. disabled) by default:
>>>
>>> CONFIG_MEMCG_SWAP=y
>>> CONFIG_SECCOMP=y
>>
>> Is it? I tried now on next-20220114 and it is still user-selectable and
>> not chosen by anything.
> 
> Hm, strange. I guess, it is due to this whole patch series, given its i.MX main focus, being based on Shawn's
> for-next branch. Maybe for such defconfig changes it would be better to base them on something else? Not sure,
> who will ultimately pull such changes. Any suggestion?

I don't think there is a one nice solution, fit-for-all.

Consider a defconfig selecting FOO and BAR, plus Kconfig like:
config FOO
	depends on BAR

If you run savedefconfig on arm-soc next branch, there is a chance that
in parallel someone else will adjust the Kconfig in some other tree,
based on Linus' master. That person removes "depends on BAR" above and
notices that FOO is mentioned in defconfig, so no need to update defconfig.

However your savedefconfig commit will exactly remove the FOO from
defconfig, because there is no reason for it to be. After merging to
Linus - FOO is gone from defconfig.

Another approach - you base your savedefconfig on linux-next. This
should solve the problem above, except that such commit might not apply
on the maintainer's tree.

Therefore recommendation is to not run savedefconfig or run it very
carefully, for example explaining why each option is being removed. I
was doing it in the past, but it's quite time consuming:

https://lore.kernel.org/linux-arm-kernel/1500270596-22384-1-git-send-email-krzk@kernel.org/

and earlier set:
https://lore.kernel.org/linux-arm-kernel/20170608161049.12421-1-krzk@kernel.org/

> 
>>> CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
>>> CONFIG_QCOM_SCM=y
>>> # CONFIG_BT_HS is not set
>>> CONFIG_FSL_MC_BUS=y
>>> CONFIG_MEDIA_CONTROLLER=y
>>> CONFIG_VIDEO_V4L2_SUBDEV_API=y
>>> CONFIG_SND_SOC_FSL_SAI=m
>>> CONFIG_USB_CONN_GPIO=m
>>> CONFIG_USB_XHCI_PCI=m
>>> CONFIG_MFD_CROS_EC_DEV=y
>>> CONFIG_COMMON_CLK_ZYNQMP=y
>>> CONFIG_SDM_GCC_845=y
>>> CONFIG_SM_GCC_8150=y
>>> CONFIG_SM_GCC_8250=y
>>> CONFIG_SLIMBUS=m
>>> CONFIG_INTERCONNECT=y
>>> CONFIG_CONFIGFS_FS=y
>>
>> All three above are still user-selectable, so please leave them. It is
>> redundant, but there is no guarantee that something selecting a
>> user-visible symbol will stop selecting it. IOW, user-visible symbols
>> should be still chosen by defconfigs if they really want them.
> 
> Well, but even if they are already enabled anyway? What is the point of savedefconfig then resp. you are saying
> that the commited defconfigs should not be generated using savedefconfig? That sounds rather confusing to me.

Yes, it's confusing. savedefconfig is too aggressive - it strips
everything which is not strictly necessary now. However there is no
guarantee that current select of some option, thus stripped out that
option via savedefconfig, will stay there forever.

If CONFIG_XXX is not user-selectable, then when someone removes the
"select XXX", it *is expected* to modify the defconfigs to add back this
XXX.

However it turns out that some developers assume that there is no such
requirement of re-adding XXX to defconfig, if XXX was user-selectable in
the first place.


> 
>> See for example commit a2315d3aea59 ("ARM: exynos_defconfig: Restore
>> debugfs support") for rationale why we need to keep them.
> 
> Okay, I see what you mean as in relation to above mentioned commit but then any change to Kconfig dependencies
> can ultimately change the behaviour of previous configs unless they are complete ones (or were just lucky to
> include whatever stuff that changed). But how should one now know which of them zillions of user-selectable
> options should be added to such "more robust" defconfigs?

No clue... :) Except maybe do not remove existing ones.

> 
> I suggest a better approach might be to have some CI which validates defconfig changes. That way one could
> easily track stuff disappearing and could at that point explicitly enable it again.

Yes, that makes sense. One defines the expected symbols to have and CI
validates whether they are enabled. We have something like this (called
annotations) in our Ubuntu configs - we store a list of config options
were are interested in and detect when they change.

Another approach is to use specialized fragments.

The benefits of such solutions is that they also document why such
option was chosen in the first place (what I was also asking from your
patches here at beginning and thanks for fixing this).

Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 02/11] dt-bindings: gpio: fix gpio-hog example

[Bartosz Golaszewski]

On Fri, Jan 14, 2022 at 3:15 PM Marcel Ziswiler <marcel@ziswiler.com> wrote:
>
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>
> Even if this is no yaml yet at least fix the example to be compliant to
> later schema as e.g. found in gpio-pca95xx.yaml, fairchild,74hc595.yaml
> and gpio/fsl-imx-gpio.yaml.
>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Acked-by: Rob Herring <robh@kernel.org>
>
> ---
>
> Changes in v2:
> - Added Rob's ack.
>
>  Documentation/devicetree/bindings/gpio/gpio.txt | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
> index a8895d339bfe..5663e71b751f 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio.txt
> +++ b/Documentation/devicetree/bindings/gpio/gpio.txt
> @@ -213,7 +213,7 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
>                 gpio-controller;
>                 #gpio-cells = <2>;
>
> -               line_b {
> +               line_b-hog {
>                         gpio-hog;
>                         gpios = <6 0>;
>                         output-low;
> --
> 2.33.1
>

Applied, thanks!

Bart

Re: [PATCH v2 02/11] dt-bindings: gpio: fix gpio-hog example

[Bartosz Golaszewski]

On Fri, Jan 14, 2022 at 3:15 PM Marcel Ziswiler <marcel@ziswiler.com> wrote:
>
> From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>
> Even if this is no yaml yet at least fix the example to be compliant to
> later schema as e.g. found in gpio-pca95xx.yaml, fairchild,74hc595.yaml
> and gpio/fsl-imx-gpio.yaml.
>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> Acked-by: Rob Herring <robh@kernel.org>
>
> ---
>
> Changes in v2:
> - Added Rob's ack.
>
>  Documentation/devicetree/bindings/gpio/gpio.txt | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
> index a8895d339bfe..5663e71b751f 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio.txt
> +++ b/Documentation/devicetree/bindings/gpio/gpio.txt
> @@ -213,7 +213,7 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
>                 gpio-controller;
>                 #gpio-cells = <2>;
>
> -               line_b {
> +               line_b-hog {
>                         gpio-hog;
>                         gpios = <6 0>;
>                         output-low;
> --
> 2.33.1
>

Applied, thanks!

Bart

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel