[U-Boot] Rockpro64_V2.1 2018-07-02 Boot Freeze【请注意，邮件由lists.intricate@gmail.com代发】

[Kever Yang <kever.yang@rock-chips.com>]

Hi Kurt,


Does this patch fix your issue?

https://patchwork.ozlabs.org/patch/1147457/


Thanks,

- Kever

On 2019/8/20 上午7:32, Kurt Miller wrote:
> Hi Jagan,
>
> On Mon, 2019-08-19 at 23:26 +0530, Jagan Teki wrote:
>> Is your board running at 50MHz? (look like No).
> No it is running at 800Mhz or 856MHz (see rkbin TPL output below).
>
>> As I said please
>> explore step-by-step
>> 00: First boot the board rkbin => SPL => U-Boot proper
> This step was completed already. Here is the output again for reference:
>
> DDR Version 1.23 20190709
> In
> channel 0
> CS = 0
> MR0=0xB8
> MR4=0x1
> MR5=0xFF
> MR8=0x10
> MR12=0x72
> MR14=0x72
> MR18=0x0
> MR19=0x0
> MR24=0x8
> MR25=0x0
> channel 1
> CS = 0
> MR0=0xB8
> MR4=0x1
> MR5=0xFF
> MR8=0x10
> MR12=0x72
> MR14=0x72
> MR18=0x0
> MR19=0x0
> MR24=0x8
> MR25=0x0
> channel 0 training pass!
> channel 1 training pass!
> change freq to 416MHz 0,1
> Channel 0: LPDDR4,416MHz
> Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
> Channel 1: LPDDR4,416MHz
> Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
> 256B stride
> channel 0
> CS = 0
> MR0=0xB8
> MR4=0x1
> MR5=0xFF
> MR8=0x10
> MR12=0x72
> MR14=0x72
> MR18=0x0
> MR19=0x0
> MR24=0x8
> MR25=0x0
> channel 1
> CS = 0
> MR0=0xB8
> MR4=0x1
> MR5=0xFF
> MR8=0x10
> MR12=0x72
> MR14=0x72
> MR18=0x0
> MR19=0x0
> MR24=0x8
> MR25=0x0
> channel 0 training pass!
> channel 1 training pass!
> channel 0, cs 0, advanced training done
> channel 1, cs 0, advanced training done
> change freq to 856MHz 1,0
> ch 0 ddrconfig = 0x101, ddrsize = 0x40
> ch 1 ddrconfig = 0x101, ddrsize = 0x40
> pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD
> OUT
>
>> 01: Grab the sdram-*.dtsi (steps mentioned in previous mail) and
>> replace rkbin withTPL
> I am stuck here. I see that there were three 800Mhz entries
> in the rkbin rk3399_ddr_800MHz_v1.20.bin file that was used to
> create ./arch/arm/dts/rk3399-sdram-lpddr4-100.dtsi.
>
> rk3399-sdram-lpddr4-100.dtsi has one entry that appears to
> be from the first 800Mhz data in rk3399_ddr_800MHz_v1.20.bin.
>
> Using the instructions you linked:
> https://wiki.amarulasolutions.com/found/target/rk3399_sdram.html
>
> I have inspected rkbin rk3399_ddr_800MHz_v1.23.bin and found
> there are two 800Mhz entries in it. I have extracted the two
> entries but have have questions that the instructions don't
> address well.
>
> Why does the existing rk3399-sdram-lpddr4-100.dtsi only have
> one entry while the instructions appear to indicate there
> should be two, one for single and another for dual ranked?
>
> Step 6 refers to editing the dtsi file:
>
> "..., edit the initial values (don’t forget that they are in
> little endian form) to match what the SPL code expects,
> convert the frequency value from the binary back into MHz
> (line 38 in the attached dtsi files for reference)"
>
> I believe I was able to convert the data into the updated
> values correctly (see attached diff). However, one value
> stood out to me. The 800Mhz value of 0x2faf0800 was converted
> into decimal 50 in the existing data whereas other sdram files
> converted it into 1/2 the Mhz value (e.g. 800Mhz -> 400).
>
> With it set to 50 I get this output before it stops:
>
> U-Boot TPL 2019.10-rc2-00016-g81fed78c0a-dirty (Aug 19 2019 - 18:45:16)
> pctl_start: Failed to init pctl for channel 0
>
> With it set to 400 I get this output before it stops:
>
> U-Boot TPL 2019.10-rc2-00016-g81fed78c0a-dirty (Aug 19 2019 - 19:14:10)
> sdram_init: DDR3 - 400MHz failed!
> rk3399_dmc_init DRAM init failed -22
> Missing DTB
>
>> 02: Then dump the regmap if 01 failed.
>>
>> Jagan.
> 01 failed. With the timings diff reverted I get this before it freezes:
>
> U-Boot TPL 2019.10-rc2-00016-g81fed78c0a-dirty (Aug 19 2019 - 12:57:39)
> LPDDR4, 50MHz
> BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB
> LPDDR4, 50MHz
> BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB
> 256B stride
> cic: ctr10: (0xff620000 - 0x14)
> cic: status0: (0xff620010 - 0x101)
> grf: ddrc0_con0 (0xff77e380 - 0x1f81)
> grf: ddrc1_con0 (0xff77e388 - 0x1f81)
> grf: soc_con0 (0xff77e200 - 0x7)
> pmu: noc_auto_ena (0xff3100d8 - 0x0)
> pmu: bus_idle_req (0xff310060 - 0x0)
> pmu: bus_idle_st (0xff310064 - 0x0)
> pmugrf: os_reg2 (0xff320308 - 0x32a1f2a1)
> pmugrf: os_reg3 (0xff32030c - 0x20000005)
> pmusgrf: soc_con4 (0xff33e010 - 0x2600)
>
> Please let me know other items can be tried to get this up and
> running with the U-Boot TPL.
>
> Regards,
> -Kurt