From mboxrd@z Thu Jan 1 00:00:00 1970 From: Peter Meerwald-Stadler Subject: Re: [PATCH] iio:temperature:Add irq and threshold events support for TI TMP007 sensor Date: Sun, 22 Jan 2017 10:19:06 +0100 (CET) Message-ID: References: <20170121150147.GA7781@gmail.com> Mime-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Return-path: In-Reply-To: <20170121150147.GA7781-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> Sender: devicetree-owner-u79uwXL29TY76Z2rM5mHXA@public.gmane.org To: Manivannan Sadhasivam Cc: jic23-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org, linux-iio-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org List-Id: devicetree@vger.kernel.org I'd prefer subject "iio:temperature:tmp007: Add irq and threshold events support" > This patch adds support for ALERT irq and limit threshold events for TI TMP007 - 16 bit IR thermopile sensor > with integrated math engine. > > Following threshold events are supported: > 1. TObj high limit > 2. TObj low limit > 3. TDie high limit > 4. TDie low limit comments below I suggest to separate clearup from actually adding events support, so two patches it would be nice if the driver can operate without irq also (irq is optional in DT...) > Signed-off-by: Manivannan Sadhasivam > --- note: this applies on top of patch... > .../devicetree/bindings/iio/temperature/tmp007.txt | 8 + > drivers/iio/temperature/tmp007.c | 334 ++++++++++++++++++--- > 2 files changed, 304 insertions(+), 38 deletions(-) > > diff --git a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt > index 3b8f41f..07c1658 100644 > --- a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt > +++ b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt > @@ -18,10 +18,18 @@ Required properties: > 1 SDA 0x46 > 1 SCL 0x47 > > +Optional properties: > + > + - interrupt-parent: should be the phandle for the interrupt controller > + > + - interrupts: interrupt mapping for GPIO IRQ > + > Example: > > tmp007@40 { > compatible = "ti,tmp007"; > reg = <0x40>; > + interrupt-parent = <&gpio0>; > + interrupts = <5 8>; why are there two GPIOs? > }; > > diff --git a/drivers/iio/temperature/tmp007.c b/drivers/iio/temperature/tmp007.c > index 24c6c16..73b5b8d 100644 > --- a/drivers/iio/temperature/tmp007.c > +++ b/drivers/iio/temperature/tmp007.c > @@ -11,9 +11,10 @@ > * > * (7-bit I2C slave address (0x40 - 0x47), changeable via ADR pins) > * > - * Note: This driver assumes that the sensor has been calibrated beforehand > - * > - * TODO: ALERT irq, limit threshold events > + * Note: > + * 1. This driver assumes that the sensor has been calibrated beforehand > + * 2. Limit threshold events are enabled at the start > + * 3. Operating mode: INT > * > */ > > @@ -24,35 +25,49 @@ > #include > #include > #include > +#include > +#include > > #include > #include > - > -#define TMP007_TDIE 0x01 > -#define TMP007_CONFIG 0x02 > -#define TMP007_TOBJECT 0x03 > -#define TMP007_STATUS 0x04 > -#define TMP007_STATUS_MASK 0x05 > -#define TMP007_MANUFACTURER_ID 0x1e > -#define TMP007_DEVICE_ID 0x1f > - > -#define TMP007_CONFIG_CONV_EN BIT(12) > -#define TMP007_CONFIG_COMP_EN BIT(5) > -#define TMP007_CONFIG_TC_EN BIT(6) > -#define TMP007_CONFIG_CR_MASK GENMASK(11, 9) > -#define TMP007_CONFIG_CR_SHIFT 9 > - > -#define TMP007_STATUS_CONV_READY BIT(14) > -#define TMP007_STATUS_DATA_VALID BIT(9) > - > -#define TMP007_MANUFACTURER_MAGIC 0x5449 > -#define TMP007_DEVICE_MAGIC 0x0078 > - > -#define TMP007_TEMP_SHIFT 2 > +#include > + > +#define TMP007_TDIE 0x01 this has a lot of clutter; the patch also reformats the #defines by adding whitespace; don't do this in the same patch > +#define TMP007_CONFIG 0x02 > +#define TMP007_TOBJECT 0x03 > +#define TMP007_STATUS 0x04 > +#define TMP007_STATUS_MASK 0x05 > +#define TMP007_TOBJ_HIGH_LIMIT 0x06 > +#define TMP007_TOBJ_LOW_LIMIT 0x07 > +#define TMP007_TDIE_HIGH_LIMIT 0x08 > +#define TMP007_TDIE_LOW_LIMIT 0x09 > +#define TMP007_MANUFACTURER_ID 0x1e > +#define TMP007_DEVICE_ID 0x1f > + > +#define TMP007_CONFIG_CONV_EN BIT(12) > +#define TMP007_CONFIG_TC_EN BIT(6) > +#define TMP007_CONFIG_CR_MASK GENMASK(11, 9) > +#define TMP007_CONFIG_ALERT_EN BIT(8) > +#define TMP007_CONFIG_CR_SHIFT 9 > + > +/* Status register flags */ > +#define TMP007_STATUS_ALERT BIT(15) > +#define TMP007_STATUS_CONV_READY BIT(14) > +#define TMP007_STATUS_OHF BIT(13) > +#define TMP007_STATUS_OLF BIT(12) > +#define TMP007_STATUS_LHF BIT(11) > +#define TMP007_STATUS_LLF BIT(10) > +#define TMP007_STATUS_DATA_VALID BIT(9) > + > +#define TMP007_MANUFACTURER_MAGIC 0x5449 > +#define TMP007_DEVICE_MAGIC 0x0078 > + > +#define TMP007_TEMP_SHIFT 2 > > struct tmp007_data { > struct i2c_client *client; > u16 config; > + u16 status_mask; > }; > > static const int tmp007_avgs[5][2] = { {4, 0}, {2, 0}, {1, 0}, > @@ -70,7 +85,7 @@ static int tmp007_read_temperature(struct tmp007_data *data, u8 reg) > return ret; > if ((ret & TMP007_STATUS_CONV_READY) && > !(ret & TMP007_STATUS_DATA_VALID)) > - break; another unrelated cleanup > + break; > msleep(100); > } > > @@ -156,6 +171,185 @@ static int tmp007_write_raw(struct iio_dev *indio_dev, > return -EINVAL; > } > > +static irqreturn_t tmp007_interrupt_handler(int irq, void *private) > +{ > + struct iio_dev *indio_dev = private; > + struct tmp007_data *data = iio_priv(indio_dev); > + int ret; > + > + ret = i2c_smbus_read_word_swapped(data->client, TMP007_STATUS); > + if (ret < 0) || !(ret & (_STATUSS_OHF | STATUS_OLF | ..)) > + return IRQ_NONE; > + > + if (ret & TMP007_STATUS_OHF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_OBJECT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_RISING), > + iio_get_time_ns(indio_dev)); > + > + if (ret & TMP007_STATUS_OLF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_OBJECT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_FALLING), > + iio_get_time_ns(indio_dev)); > + > + if (ret & TMP007_STATUS_LHF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_AMBIENT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_RISING), > + iio_get_time_ns(indio_dev)); > + > + if (ret & TMP007_STATUS_LLF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_AMBIENT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_FALLING), > + iio_get_time_ns(indio_dev)); > + > + return IRQ_HANDLED; > +} > + > +static int tmp007_write_event_config(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir, int state) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + unsigned int status_mask; > + int ret; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: > + if (dir == IIO_EV_DIR_RISING) > + status_mask = TMP007_STATUS_LHF; > + else > + status_mask = TMP007_STATUS_LLF; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + status_mask = TMP007_STATUS_OHF; > + else > + status_mask = TMP007_STATUS_OLF; > + break; > + default: > + return -EINVAL; > + } > + mutex around this? > + ret = i2c_smbus_read_word_swapped(data->client, TMP007_STATUS_MASK); > + if (ret < 0) > + return ret; > + > + if (state) > + ret |= status_mask; > + else > + ret &= ~status_mask; > + > + return i2c_smbus_write_word_swapped(data->client, TMP007_STATUS_MASK, > + data->status_mask = ret); > +} > + > +static int tmp007_read_event_config(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + unsigned int mask; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: > + if (dir == IIO_EV_DIR_RISING) > + mask = TMP007_STATUS_LHF; > + else > + mask = TMP007_STATUS_LLF; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + mask = TMP007_STATUS_OHF; > + else > + mask = TMP007_STATUS_OLF; > + break; > + default: > + return -EINVAL; > + } > + > + return (bool)(data->status_mask & mask); return type is int, maybe use !! to force to 0/1 return !!(data->status_mask & mask); > +} > + > +static int tmp007_read_thresh(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir, enum iio_event_info info, > + int *val, int *val2) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + int ret; > + u8 reg; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: /* LSB: 0.5 degree Celsius */ > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TDIE_HIGH_LIMIT; > + else > + reg = TMP007_TDIE_LOW_LIMIT; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TOBJ_HIGH_LIMIT; > + else > + reg = TMP007_TOBJ_LOW_LIMIT; > + break; > + default: > + return -EINVAL; > + } > + > + ret = i2c_smbus_read_word_swapped(data->client, reg); > + if (ret < 0) > + return ret; > + > + /* Shift length 7 bits = 6(15:6) + 1(0.5 LSB) */ > + *val = sign_extend32(ret, 15) >> 7; > + > + return IIO_VAL_INT; > +} > + > +static int tmp007_write_thresh(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir, enum iio_event_info info, > + int val, int val2) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + u8 reg; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TDIE_HIGH_LIMIT; > + else > + reg = TMP007_TDIE_LOW_LIMIT; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TOBJ_HIGH_LIMIT; > + else > + reg = TMP007_TOBJ_LOW_LIMIT; > + break; > + default: > + return -EINVAL; > + } > + > + /* Full scale value is +/- 256 degree Celsius */ I guess we want to specify milli degree Celsius according to sysfs-bus-iio for in_temp_raw > + if (val < -256 || val > 255) > + return -EINVAL; > + > + /* Shift length 7 bits = 6(15:6) + 1(0.5 LSB) */ > + return i2c_smbus_write_word_swapped(data->client, reg, (val << 7)); > +} > + > static IIO_CONST_ATTR(sampling_frequency_available, "4 2 1 0.5 0.25"); > > static struct attribute *tmp007_attributes[] = { > @@ -167,6 +361,36 @@ static const struct attribute_group tmp007_attribute_group = { > .attrs = tmp007_attributes, > }; > > +static const struct iio_event_spec tmp007_obj_event[] = { > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_RISING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_FALLING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > +}; > + > +static const struct iio_event_spec tmp007_die_event[] = { > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_RISING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_FALLING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > +}; > + > static const struct iio_chan_spec tmp007_channels[] = { > { > .type = IIO_TEMP, > @@ -175,6 +399,8 @@ static const struct iio_chan_spec tmp007_channels[] = { > .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | > BIT(IIO_CHAN_INFO_SCALE), > .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), > + .event_spec = tmp007_die_event, > + .num_event_specs = ARRAY_SIZE(tmp007_die_event), > }, > { > .type = IIO_TEMP, > @@ -183,12 +409,18 @@ static const struct iio_chan_spec tmp007_channels[] = { > .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | > BIT(IIO_CHAN_INFO_SCALE), > .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), > - } > + .event_spec = tmp007_obj_event, > + .num_event_specs = ARRAY_SIZE(tmp007_obj_event), > + }, > }; > > static const struct iio_info tmp007_info = { > - .read_raw = tmp007_read_raw, > - .write_raw = tmp007_write_raw, > + .read_raw = &tmp007_read_raw, > + .write_raw = &tmp007_write_raw, unrelated change, no need for & for a function > + .read_event_config = &tmp007_read_event_config, > + .write_event_config = &tmp007_write_event_config, > + .read_event_value = &tmp007_read_thresh, > + .write_event_value = &tmp007_write_thresh, > .attrs = &tmp007_attribute_group, > .driver_module = THIS_MODULE, > }; > @@ -214,7 +446,6 @@ static int tmp007_probe(struct i2c_client *client, > struct tmp007_data *data; > struct iio_dev *indio_dev; > int ret; > - u16 status; > > if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA)) > return -EOPNOTSUPP; > @@ -243,8 +474,8 @@ static int tmp007_probe(struct i2c_client *client, > /* > * Set Configuration register: > * 1. Conversion ON > - * 2. Comparator mode > - * 3. Transient correction enable > + * 2. Transient correction enable > + * 3. ALERT enable > */ > > ret = i2c_smbus_read_word_swapped(data->client, TMP007_CONFIG); > @@ -252,7 +483,7 @@ static int tmp007_probe(struct i2c_client *client, > return ret; > > data->config = ret; > - data->config |= (TMP007_CONFIG_CONV_EN | TMP007_CONFIG_COMP_EN | TMP007_CONFIG_TC_EN); > + data->config |= (TMP007_CONFIG_CONV_EN | TMP007_CONFIG_TC_EN | TMP007_CONFIG_ALERT_EN); > > ret = i2c_smbus_write_word_swapped(data->client, TMP007_CONFIG, > data->config); > @@ -260,22 +491,39 @@ static int tmp007_probe(struct i2c_client *client, > return ret; > > /* > + * Only the following flags can activate ALERT pin. Data conversion/validity flags > + * flags can still be polled for getting temperature data > + * > * Set Status Mask register: > - * 1. Conversion ready enable > - * 2. Data valid enable > + * 1. Object temperature high limit enable > + * 2. Object temperature low limit enable > + * 3. TDIE temperature high limit enable > + * 4. TDIE temperature low limit enable > */ > > ret = i2c_smbus_read_word_swapped(data->client, TMP007_STATUS_MASK); > if (ret < 0) > goto error_powerdown; > > - status = ret; > - status |= (TMP007_STATUS_CONV_READY | TMP007_STATUS_DATA_VALID); > + data->status_mask = ret; > + data->status_mask |= (TMP007_STATUS_OHF | TMP007_STATUS_OLF > + | TMP007_STATUS_LHF | TMP007_STATUS_LLF); > > - ret = i2c_smbus_write_word_swapped(data->client, TMP007_STATUS_MASK, status); > + ret = i2c_smbus_write_word_swapped(data->client, TMP007_STATUS_MASK, data->status_mask); > if (ret < 0) > goto error_powerdown; > > + if (client->irq) { > + ret = devm_request_threaded_irq(&client->dev, client->irq, > + NULL, tmp007_interrupt_handler, > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + tmp007_id->name, indio_dev); > + if (ret) { > + dev_err(&client->dev, "irq request error %d\n", -ret); > + goto error_powerdown; > + } > + } what happens when there is no IRQ? it would be nice to still use the driver (without event capability) > + > return iio_device_register(indio_dev); > > error_powerdown: > @@ -312,6 +560,16 @@ static int tmp007_resume(struct device *dev) > return i2c_smbus_write_word_swapped(data->client, TMP007_CONFIG, > data->config | TMP007_CONFIG_CONV_EN); > } > +#else this seems to be unrelated to the patch > +static int tmp007_suspend(struct device *dev) > +{ > + return 0; > +} > + > +static int tmp007_resume(struct device *dev) > +{ > + return 0; > +} > #endif > > static SIMPLE_DEV_PM_OPS(tmp007_pm_ops, tmp007_suspend, tmp007_resume); > -- Peter Meerwald-Stadler +43-664-2444418 (mobile) -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Date: Sun, 22 Jan 2017 10:19:06 +0100 (CET) From: Peter Meerwald-Stadler To: Manivannan Sadhasivam cc: jic23@kernel.org, linux-iio@vger.kernel.org, devicetree@vger.kernel.org Subject: Re: [PATCH] iio:temperature:Add irq and threshold events support for TI TMP007 sensor In-Reply-To: <20170121150147.GA7781@gmail.com> Message-ID: References: <20170121150147.GA7781@gmail.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII List-ID: I'd prefer subject "iio:temperature:tmp007: Add irq and threshold events support" > This patch adds support for ALERT irq and limit threshold events for TI TMP007 - 16 bit IR thermopile sensor > with integrated math engine. > > Following threshold events are supported: > 1. TObj high limit > 2. TObj low limit > 3. TDie high limit > 4. TDie low limit comments below I suggest to separate clearup from actually adding events support, so two patches it would be nice if the driver can operate without irq also (irq is optional in DT...) > Signed-off-by: Manivannan Sadhasivam > --- note: this applies on top of patch... > .../devicetree/bindings/iio/temperature/tmp007.txt | 8 + > drivers/iio/temperature/tmp007.c | 334 ++++++++++++++++++--- > 2 files changed, 304 insertions(+), 38 deletions(-) > > diff --git a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt > index 3b8f41f..07c1658 100644 > --- a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt > +++ b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt > @@ -18,10 +18,18 @@ Required properties: > 1 SDA 0x46 > 1 SCL 0x47 > > +Optional properties: > + > + - interrupt-parent: should be the phandle for the interrupt controller > + > + - interrupts: interrupt mapping for GPIO IRQ > + > Example: > > tmp007@40 { > compatible = "ti,tmp007"; > reg = <0x40>; > + interrupt-parent = <&gpio0>; > + interrupts = <5 8>; why are there two GPIOs? > }; > > diff --git a/drivers/iio/temperature/tmp007.c b/drivers/iio/temperature/tmp007.c > index 24c6c16..73b5b8d 100644 > --- a/drivers/iio/temperature/tmp007.c > +++ b/drivers/iio/temperature/tmp007.c > @@ -11,9 +11,10 @@ > * > * (7-bit I2C slave address (0x40 - 0x47), changeable via ADR pins) > * > - * Note: This driver assumes that the sensor has been calibrated beforehand > - * > - * TODO: ALERT irq, limit threshold events > + * Note: > + * 1. This driver assumes that the sensor has been calibrated beforehand > + * 2. Limit threshold events are enabled at the start > + * 3. Operating mode: INT > * > */ > > @@ -24,35 +25,49 @@ > #include > #include > #include > +#include > +#include > > #include > #include > - > -#define TMP007_TDIE 0x01 > -#define TMP007_CONFIG 0x02 > -#define TMP007_TOBJECT 0x03 > -#define TMP007_STATUS 0x04 > -#define TMP007_STATUS_MASK 0x05 > -#define TMP007_MANUFACTURER_ID 0x1e > -#define TMP007_DEVICE_ID 0x1f > - > -#define TMP007_CONFIG_CONV_EN BIT(12) > -#define TMP007_CONFIG_COMP_EN BIT(5) > -#define TMP007_CONFIG_TC_EN BIT(6) > -#define TMP007_CONFIG_CR_MASK GENMASK(11, 9) > -#define TMP007_CONFIG_CR_SHIFT 9 > - > -#define TMP007_STATUS_CONV_READY BIT(14) > -#define TMP007_STATUS_DATA_VALID BIT(9) > - > -#define TMP007_MANUFACTURER_MAGIC 0x5449 > -#define TMP007_DEVICE_MAGIC 0x0078 > - > -#define TMP007_TEMP_SHIFT 2 > +#include > + > +#define TMP007_TDIE 0x01 this has a lot of clutter; the patch also reformats the #defines by adding whitespace; don't do this in the same patch > +#define TMP007_CONFIG 0x02 > +#define TMP007_TOBJECT 0x03 > +#define TMP007_STATUS 0x04 > +#define TMP007_STATUS_MASK 0x05 > +#define TMP007_TOBJ_HIGH_LIMIT 0x06 > +#define TMP007_TOBJ_LOW_LIMIT 0x07 > +#define TMP007_TDIE_HIGH_LIMIT 0x08 > +#define TMP007_TDIE_LOW_LIMIT 0x09 > +#define TMP007_MANUFACTURER_ID 0x1e > +#define TMP007_DEVICE_ID 0x1f > + > +#define TMP007_CONFIG_CONV_EN BIT(12) > +#define TMP007_CONFIG_TC_EN BIT(6) > +#define TMP007_CONFIG_CR_MASK GENMASK(11, 9) > +#define TMP007_CONFIG_ALERT_EN BIT(8) > +#define TMP007_CONFIG_CR_SHIFT 9 > + > +/* Status register flags */ > +#define TMP007_STATUS_ALERT BIT(15) > +#define TMP007_STATUS_CONV_READY BIT(14) > +#define TMP007_STATUS_OHF BIT(13) > +#define TMP007_STATUS_OLF BIT(12) > +#define TMP007_STATUS_LHF BIT(11) > +#define TMP007_STATUS_LLF BIT(10) > +#define TMP007_STATUS_DATA_VALID BIT(9) > + > +#define TMP007_MANUFACTURER_MAGIC 0x5449 > +#define TMP007_DEVICE_MAGIC 0x0078 > + > +#define TMP007_TEMP_SHIFT 2 > > struct tmp007_data { > struct i2c_client *client; > u16 config; > + u16 status_mask; > }; > > static const int tmp007_avgs[5][2] = { {4, 0}, {2, 0}, {1, 0}, > @@ -70,7 +85,7 @@ static int tmp007_read_temperature(struct tmp007_data *data, u8 reg) > return ret; > if ((ret & TMP007_STATUS_CONV_READY) && > !(ret & TMP007_STATUS_DATA_VALID)) > - break; another unrelated cleanup > + break; > msleep(100); > } > > @@ -156,6 +171,185 @@ static int tmp007_write_raw(struct iio_dev *indio_dev, > return -EINVAL; > } > > +static irqreturn_t tmp007_interrupt_handler(int irq, void *private) > +{ > + struct iio_dev *indio_dev = private; > + struct tmp007_data *data = iio_priv(indio_dev); > + int ret; > + > + ret = i2c_smbus_read_word_swapped(data->client, TMP007_STATUS); > + if (ret < 0) || !(ret & (_STATUSS_OHF | STATUS_OLF | ..)) > + return IRQ_NONE; > + > + if (ret & TMP007_STATUS_OHF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_OBJECT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_RISING), > + iio_get_time_ns(indio_dev)); > + > + if (ret & TMP007_STATUS_OLF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_OBJECT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_FALLING), > + iio_get_time_ns(indio_dev)); > + > + if (ret & TMP007_STATUS_LHF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_AMBIENT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_RISING), > + iio_get_time_ns(indio_dev)); > + > + if (ret & TMP007_STATUS_LLF) > + iio_push_event(indio_dev, > + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, > + IIO_MOD_TEMP_AMBIENT, > + IIO_EV_TYPE_THRESH, > + IIO_EV_DIR_FALLING), > + iio_get_time_ns(indio_dev)); > + > + return IRQ_HANDLED; > +} > + > +static int tmp007_write_event_config(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir, int state) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + unsigned int status_mask; > + int ret; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: > + if (dir == IIO_EV_DIR_RISING) > + status_mask = TMP007_STATUS_LHF; > + else > + status_mask = TMP007_STATUS_LLF; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + status_mask = TMP007_STATUS_OHF; > + else > + status_mask = TMP007_STATUS_OLF; > + break; > + default: > + return -EINVAL; > + } > + mutex around this? > + ret = i2c_smbus_read_word_swapped(data->client, TMP007_STATUS_MASK); > + if (ret < 0) > + return ret; > + > + if (state) > + ret |= status_mask; > + else > + ret &= ~status_mask; > + > + return i2c_smbus_write_word_swapped(data->client, TMP007_STATUS_MASK, > + data->status_mask = ret); > +} > + > +static int tmp007_read_event_config(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + unsigned int mask; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: > + if (dir == IIO_EV_DIR_RISING) > + mask = TMP007_STATUS_LHF; > + else > + mask = TMP007_STATUS_LLF; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + mask = TMP007_STATUS_OHF; > + else > + mask = TMP007_STATUS_OLF; > + break; > + default: > + return -EINVAL; > + } > + > + return (bool)(data->status_mask & mask); return type is int, maybe use !! to force to 0/1 return !!(data->status_mask & mask); > +} > + > +static int tmp007_read_thresh(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir, enum iio_event_info info, > + int *val, int *val2) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + int ret; > + u8 reg; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: /* LSB: 0.5 degree Celsius */ > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TDIE_HIGH_LIMIT; > + else > + reg = TMP007_TDIE_LOW_LIMIT; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TOBJ_HIGH_LIMIT; > + else > + reg = TMP007_TOBJ_LOW_LIMIT; > + break; > + default: > + return -EINVAL; > + } > + > + ret = i2c_smbus_read_word_swapped(data->client, reg); > + if (ret < 0) > + return ret; > + > + /* Shift length 7 bits = 6(15:6) + 1(0.5 LSB) */ > + *val = sign_extend32(ret, 15) >> 7; > + > + return IIO_VAL_INT; > +} > + > +static int tmp007_write_thresh(struct iio_dev *indio_dev, > + const struct iio_chan_spec *chan, enum iio_event_type type, > + enum iio_event_direction dir, enum iio_event_info info, > + int val, int val2) > +{ > + struct tmp007_data *data = iio_priv(indio_dev); > + u8 reg; > + > + switch (chan->channel2) { > + case IIO_MOD_TEMP_AMBIENT: > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TDIE_HIGH_LIMIT; > + else > + reg = TMP007_TDIE_LOW_LIMIT; > + break; > + case IIO_MOD_TEMP_OBJECT: > + if (dir == IIO_EV_DIR_RISING) > + reg = TMP007_TOBJ_HIGH_LIMIT; > + else > + reg = TMP007_TOBJ_LOW_LIMIT; > + break; > + default: > + return -EINVAL; > + } > + > + /* Full scale value is +/- 256 degree Celsius */ I guess we want to specify milli degree Celsius according to sysfs-bus-iio for in_temp_raw > + if (val < -256 || val > 255) > + return -EINVAL; > + > + /* Shift length 7 bits = 6(15:6) + 1(0.5 LSB) */ > + return i2c_smbus_write_word_swapped(data->client, reg, (val << 7)); > +} > + > static IIO_CONST_ATTR(sampling_frequency_available, "4 2 1 0.5 0.25"); > > static struct attribute *tmp007_attributes[] = { > @@ -167,6 +361,36 @@ static const struct attribute_group tmp007_attribute_group = { > .attrs = tmp007_attributes, > }; > > +static const struct iio_event_spec tmp007_obj_event[] = { > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_RISING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_FALLING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > +}; > + > +static const struct iio_event_spec tmp007_die_event[] = { > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_RISING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > + { > + .type = IIO_EV_TYPE_THRESH, > + .dir = IIO_EV_DIR_FALLING, > + .mask_separate = BIT(IIO_EV_INFO_VALUE) | > + BIT(IIO_EV_INFO_ENABLE), > + }, > +}; > + > static const struct iio_chan_spec tmp007_channels[] = { > { > .type = IIO_TEMP, > @@ -175,6 +399,8 @@ static const struct iio_chan_spec tmp007_channels[] = { > .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | > BIT(IIO_CHAN_INFO_SCALE), > .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), > + .event_spec = tmp007_die_event, > + .num_event_specs = ARRAY_SIZE(tmp007_die_event), > }, > { > .type = IIO_TEMP, > @@ -183,12 +409,18 @@ static const struct iio_chan_spec tmp007_channels[] = { > .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | > BIT(IIO_CHAN_INFO_SCALE), > .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), > - } > + .event_spec = tmp007_obj_event, > + .num_event_specs = ARRAY_SIZE(tmp007_obj_event), > + }, > }; > > static const struct iio_info tmp007_info = { > - .read_raw = tmp007_read_raw, > - .write_raw = tmp007_write_raw, > + .read_raw = &tmp007_read_raw, > + .write_raw = &tmp007_write_raw, unrelated change, no need for & for a function > + .read_event_config = &tmp007_read_event_config, > + .write_event_config = &tmp007_write_event_config, > + .read_event_value = &tmp007_read_thresh, > + .write_event_value = &tmp007_write_thresh, > .attrs = &tmp007_attribute_group, > .driver_module = THIS_MODULE, > }; > @@ -214,7 +446,6 @@ static int tmp007_probe(struct i2c_client *client, > struct tmp007_data *data; > struct iio_dev *indio_dev; > int ret; > - u16 status; > > if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA)) > return -EOPNOTSUPP; > @@ -243,8 +474,8 @@ static int tmp007_probe(struct i2c_client *client, > /* > * Set Configuration register: > * 1. Conversion ON > - * 2. Comparator mode > - * 3. Transient correction enable > + * 2. Transient correction enable > + * 3. ALERT enable > */ > > ret = i2c_smbus_read_word_swapped(data->client, TMP007_CONFIG); > @@ -252,7 +483,7 @@ static int tmp007_probe(struct i2c_client *client, > return ret; > > data->config = ret; > - data->config |= (TMP007_CONFIG_CONV_EN | TMP007_CONFIG_COMP_EN | TMP007_CONFIG_TC_EN); > + data->config |= (TMP007_CONFIG_CONV_EN | TMP007_CONFIG_TC_EN | TMP007_CONFIG_ALERT_EN); > > ret = i2c_smbus_write_word_swapped(data->client, TMP007_CONFIG, > data->config); > @@ -260,22 +491,39 @@ static int tmp007_probe(struct i2c_client *client, > return ret; > > /* > + * Only the following flags can activate ALERT pin. Data conversion/validity flags > + * flags can still be polled for getting temperature data > + * > * Set Status Mask register: > - * 1. Conversion ready enable > - * 2. Data valid enable > + * 1. Object temperature high limit enable > + * 2. Object temperature low limit enable > + * 3. TDIE temperature high limit enable > + * 4. TDIE temperature low limit enable > */ > > ret = i2c_smbus_read_word_swapped(data->client, TMP007_STATUS_MASK); > if (ret < 0) > goto error_powerdown; > > - status = ret; > - status |= (TMP007_STATUS_CONV_READY | TMP007_STATUS_DATA_VALID); > + data->status_mask = ret; > + data->status_mask |= (TMP007_STATUS_OHF | TMP007_STATUS_OLF > + | TMP007_STATUS_LHF | TMP007_STATUS_LLF); > > - ret = i2c_smbus_write_word_swapped(data->client, TMP007_STATUS_MASK, status); > + ret = i2c_smbus_write_word_swapped(data->client, TMP007_STATUS_MASK, data->status_mask); > if (ret < 0) > goto error_powerdown; > > + if (client->irq) { > + ret = devm_request_threaded_irq(&client->dev, client->irq, > + NULL, tmp007_interrupt_handler, > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + tmp007_id->name, indio_dev); > + if (ret) { > + dev_err(&client->dev, "irq request error %d\n", -ret); > + goto error_powerdown; > + } > + } what happens when there is no IRQ? it would be nice to still use the driver (without event capability) > + > return iio_device_register(indio_dev); > > error_powerdown: > @@ -312,6 +560,16 @@ static int tmp007_resume(struct device *dev) > return i2c_smbus_write_word_swapped(data->client, TMP007_CONFIG, > data->config | TMP007_CONFIG_CONV_EN); > } > +#else this seems to be unrelated to the patch > +static int tmp007_suspend(struct device *dev) > +{ > + return 0; > +} > + > +static int tmp007_resume(struct device *dev) > +{ > + return 0; > +} > #endif > > static SIMPLE_DEV_PM_OPS(tmp007_pm_ops, tmp007_suspend, tmp007_resume); > -- Peter Meerwald-Stadler +43-664-2444418 (mobile)