All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
@ 2022-05-25  3:42 David Wang
  2022-05-25  6:16 ` Krzysztof Kozlowski
  0 siblings, 1 reply; 7+ messages in thread
From: David Wang @ 2022-05-25  3:42 UTC (permalink / raw)
  To: robh+dt, krzysztof.kozlowski+dt, devicetree, linux-kernel
  Cc: edward_chen, ben_pai, David Wang

The initial introduction of the jabil server with AST2600 BMC SoC.

---

v2
- Disable empty i2c bus.
- Remove gfx node because aspeed-g6.dtsi isn't supported.
- Modify the led format and add some properties.
- Fix wrong indentation.
- Add stdout property in chosen node.
- Rename temp to temperature-sensor in i2c bus 0.

---

Signed-off-by: David Wang <David_Wang6097@jabil.com>
---
 arch/arm/boot/dts/Makefile                    |   3 +-
 .../boot/dts/aspeed-bmc-jabil-rubypass.dts    | 449 ++++++++++++++++++
 2 files changed, 451 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c16f8a2b738..9c395178fc89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-tyan-s8036.dtb \
 	aspeed-bmc-vegman-n110.dtb \
 	aspeed-bmc-vegman-rx20.dtb \
-	aspeed-bmc-vegman-sx20.dtb
+	aspeed-bmc-vegman-sx20.dtb \
+	aspeed-bmc-jabil-rubypass.dtb
diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
new file mode 100644
index 000000000000..0e1450f66372
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
@@ -0,0 +1,449 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Jabil rbp";
+	compatible = "aspeed,ast2600";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	vcc_sdhci0: regulator-vcc-sdhci0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+
+	vccq_sdhci0: regulator-vccq-sdhci0 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	vcc_sdhci1: regulator-vcc-sdhci1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhci1: regulator-vccq-sdhci1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+
+		led-0 {
+			label = "identify";
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_INDICATOR;
+			retain-state-shutdown;
+			gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			label = "status_amber";
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			label = "status_green";
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "keep";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			label = "status_susack";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
+		};
+
+		led-4{
+			label = "power-amber";
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	fan_fault {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+
+		led-0 {
+			label = "fan1-fault";
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_FAULT;
+			retain-state-shutdown;
+			gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			label = "fan2-fault";
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_FAULT;
+			retain-state-shutdown;
+			gpios = <&gpio3_71 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "fan3-fault";
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_FAULT;
+			retain-state-shutdown;
+			gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			label = "fan4-fault";
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_FAULT;
+			retain-state-shutdown;
+			gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "fan5-fault";
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_FAULT;
+			retain-state-shutdown;
+			gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			label = "fan6-fault";
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_FAULT;
+			retain-state-shutdown;
+			gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+
+	ethphy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&mac1 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy1>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default>;
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	non-removable;
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default
+			&pinctrl_nrts1_default
+			&pinctrl_ndtr1_default
+			&pinctrl_ndsr1_default
+			&pinctrl_ncts1_default
+			&pinctrl_ndcd1_default
+			&pinctrl_nri1_default>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_txd2_default
+			&pinctrl_rxd2_default
+			&pinctrl_nrts2_default
+			&pinctrl_ndtr2_default
+			&pinctrl_ndsr2_default
+			&pinctrl_ncts2_default
+			&pinctrl_ndcd2_default
+			&pinctrl_nri2_default>;
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c3 {
+	multi-master;
+	status = "okay";
+
+	gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
+			"presence-fan5-n", "presence-fan6-n", "", "";
+	};
+
+	gpio3_71:gpio@71 {
+		compatible = "nxp,pca9538";
+		reg = <0x71>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
+			"led-fan5-fault", "led-fan6-fault", "", "";
+	};
+};
+
+&fsim0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&sdc {
+	status = "okay";
+};
+
+/*
+ * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
+ * toggled by GPIO pins.
+ * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
+ * a 1.8v and a 3.3v power load switch that provides signal voltage to
+ * sdhci0 bus.
+ * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
+ * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
+ * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
+ * sdhci0 signal voltage becomes 1.8v.
+ * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
+ * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
+ * as power-switch-gpio.
+ */
+&sdhci0 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci0>;
+	vqmmc-supply = <&vccq_sdhci0>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&sdhci1 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci1>;
+	vqmmc-supply = <&vccq_sdhci1>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&gpio0 {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/       "","","","","","","","",
+	/*B0-B7*/       "presence-ncsi-i210-n","","","","","","","led-identify-n",
+	/*C0-C7*/       "","","","","","","","",
+	/*D0-D7*/       "","","","","","","","",
+	/*E0-E7*/       "","","","","","","","",
+	/*F0-F7*/       "","","","","","","id-button","",
+	/*G0-G7*/       "","","led-status-green-n","led-status-amber-n","","","","",
+	/*H0-H7*/       "","","","","","cpu-caterr","","cpu1-caterr-n",
+	/*I0-I7*/       "","","","","","","","",
+	/*J0-J7*/       "","","","","","","","",
+	/*K0-K7*/       "","","","","","","","",
+	/*L0-L7*/       "","","","","","","","",
+	/*M0-M7*/       "","","","","","","","",
+	/*N0-N7*/       "","","","","","","","",
+	/*O0-O7*/       "","","","","","","nmi-button","",
+	/*P0-P7*/       "reset-button","reset-out","power-button","power-out","","","",
+					"led-hartbeat-n",
+	/*Q0-Q7*/       "","","","","","","","",
+	/*R0-R7*/       "","","","","","","","",
+	/*S0-S7*/       "","","","","","","","",
+	/*T0-T7*/       "","","","","","","","",
+	/*U0-U7*/       "","","","","","","","",
+	/*V0-V7*/       "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1",
+					"regulator-vccq-sdhci1","sio-power-good",
+					"led-bmc-fw-config-done-n","","",
+	/*W0-W7*/       "","","","","","","","",
+	/*X0-X7*/       "cpu-err2","","","","","","","",
+	/*Y0-Y7*/       "led-power-amber","","","","","","","",
+	/*Z0-Z7*/       "cpu-err0","cpu-err1","","","","","","";
+	};
+
+&gpio1 {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xCA2>;
+	status = "okay";
+};
+
+&kcs4 {
+	aspeed,lpc-io-reg = <0xCA4>;
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 7+ messages in thread

* Re: [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
  2022-05-25  3:42 [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC David Wang
@ 2022-05-25  6:16 ` Krzysztof Kozlowski
  0 siblings, 0 replies; 7+ messages in thread
From: Krzysztof Kozlowski @ 2022-05-25  6:16 UTC (permalink / raw)
  To: David Wang, robh+dt, krzysztof.kozlowski+dt, devicetree, linux-kernel
  Cc: edward_chen, ben_pai

On 25/05/2022 05:42, David Wang wrote:
> The initial introduction of the jabil server with AST2600 BMC SoC.
> 
> ---
> 
> v2
> - Disable empty i2c bus.
> - Remove gfx node because aspeed-g6.dtsi isn't supported.
> - Modify the led format and add some properties.
> - Fix wrong indentation.
> - Add stdout property in chosen node.
> - Rename temp to temperature-sensor in i2c bus 0.
> 
> ---
> 
> Signed-off-by: David Wang <David_Wang6097@jabil.com>
> ---
>  arch/arm/boot/dts/Makefile                    |   3 +-
>  .../boot/dts/aspeed-bmc-jabil-rubypass.dts    | 449 ++++++++++++++++++
>  2 files changed, 451 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7c16f8a2b738..9c395178fc89 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>  	aspeed-bmc-tyan-s8036.dtb \
>  	aspeed-bmc-vegman-n110.dtb \
>  	aspeed-bmc-vegman-rx20.dtb \
> -	aspeed-bmc-vegman-sx20.dtb
> +	aspeed-bmc-vegman-sx20.dtb \
> +	aspeed-bmc-jabil-rubypass.dtb

The entries are ordered by name and your new name looks out of order...

> diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> new file mode 100644
> index 000000000000..0e1450f66372
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> @@ -0,0 +1,449 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	model = "Jabil rbp";
> +	compatible = "aspeed,ast2600";
> +
> +	chosen {
> +		stdout-path = &uart5;
> +		bootargs = "console=ttyS4,115200n8";

You do not need bootargs. Use stdout-path.

> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x80000000>;
> +	};
> +
> +	vcc_sdhci0: regulator-vcc-sdhci0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "SDHCI0 Vcc";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +
> +	vccq_sdhci0: regulator-vccq-sdhci0 {
> +		compatible = "regulator-gpio";
> +		regulator-name = "SDHCI0 VccQ";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
> +		gpios-states = <1>;
> +		states = <3300000 1>,
> +			 <1800000 0>;
> +	};
> +
> +	vcc_sdhci1: regulator-vcc-sdhci1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "SDHCI1 Vcc";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	vccq_sdhci1: regulator-vccq-sdhci1 {
> +		compatible = "regulator-gpio";
> +		regulator-name = "SDHCI1 VccQ";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
> +		gpios-states = <1>;
> +		states = <3300000 1>,
> +			 <1800000 0>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +
> +		led-0 {
> +			label = "identify";
> +			color = <LED_COLOR_ID_BLUE>;
> +			function = LED_FUNCTION_INDICATOR;
> +			retain-state-shutdown;
> +			gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		led-1 {
> +			label = "status_amber";
> +			color = <LED_COLOR_ID_AMBER>;
> +			function = LED_FUNCTION_STATUS;
> +			gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		led-2 {
> +			label = "status_green";
> +			color = <LED_COLOR_ID_GREEN>;
> +			default-state = "keep";
> +			function = LED_FUNCTION_STATUS;
> +			gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		led-3 {
> +			label = "status_susack";
> +			function = LED_FUNCTION_STATUS;
> +			gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
> +		};
> +
> +		led-4{
> +			label = "power-amber";
> +			color = <LED_COLOR_ID_AMBER>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	fan_fault {

No underscores in node names, generic node names, so leds-1 (and
previous leds-0). Although main question - why do you need two instances
of drivers?

> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +
> +		led-0 {
> +			label = "fan1-fault";
> +			color = <LED_COLOR_ID_YELLOW>;
> +			function = LED_FUNCTION_FAULT;
> +			retain-state-shutdown;
> +			gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		led-1 {
> +			label = "fan2-fault";
> +			color = <LED_COLOR_ID_YELLOW>;
> +			function = LED_FUNCTION_FAULT;
> +			retain-state-shutdown;
> +			gpios = <&gpio3_71 1 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		led-2 {
> +			label = "fan3-fault";
> +			color = <LED_COLOR_ID_YELLOW>;
> +			function = LED_FUNCTION_FAULT;
> +			retain-state-shutdown;
> +			gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		led-3 {
> +			label = "fan4-fault";
> +			color = <LED_COLOR_ID_YELLOW>;
> +			function = LED_FUNCTION_FAULT;
> +			retain-state-shutdown;
> +			gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		led-4 {
> +			label = "fan5-fault";
> +			color = <LED_COLOR_ID_YELLOW>;
> +			function = LED_FUNCTION_FAULT;
> +			retain-state-shutdown;
> +			gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
> +		};
> +
> +		led-5 {
> +			label = "fan6-fault";
> +			color = <LED_COLOR_ID_YELLOW>;
> +			function = LED_FUNCTION_FAULT;
> +			retain-state-shutdown;
> +			gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
> +		};
> +	};
> +};
> +
> +&mdio0 {
> +	status = "okay";
> +
> +	ethphy0: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mdio1 {
> +	status = "okay";
> +
> +	ethphy1: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mdio2 {
> +	status = "okay";
> +
> +	ethphy2: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mdio3 {
> +	status = "okay";
> +
> +	ethphy3: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mac0 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii-rxid";
> +	phy-handle = <&ethphy0>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii1_default>;
> +};
> +
> +&mac1 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii-rxid";
> +	phy-handle = <&ethphy1>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii2_default>;
> +};
> +
> +&mac2 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii";
> +	phy-handle = <&ethphy2>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii3_default>;
> +};
> +
> +&mac3 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii";
> +	phy-handle = <&ethphy3>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii4_default>;
> +};
> +
> +&emmc_controller {
> +	status = "okay";
> +};
> +
> +&emmc {
> +	non-removable;
> +	bus-width = <4>;
> +	max-frequency = <100000000>;
> +	clk-phase-mmc-hs200 = <9>, <225>;
> +};
> +
> +&rtc {
> +	status = "okay";
> +};
> +
> +&fmc {
> +	status = "okay";
> +	flash@0 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "bmc";
> +		spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-128.dtsi"
> +	};
> +};
> +
> +&spi1 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spi1_default>;
> +
> +	flash@0 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "pnor";
> +		spi-max-frequency = <100000000>;
> +	};
> +};
> +
> +&uart1 {
> +	status = "okay";
> +	pinctrl-0 = <&pinctrl_txd1_default
> +			&pinctrl_rxd1_default
> +			&pinctrl_nrts1_default
> +			&pinctrl_ndtr1_default
> +			&pinctrl_ndsr1_default
> +			&pinctrl_ncts1_default
> +			&pinctrl_ndcd1_default
> +			&pinctrl_nri1_default>;
> +};
> +
> +&uart2 {
> +	status = "okay";
> +	pinctrl-0 = <&pinctrl_txd2_default
> +			&pinctrl_rxd2_default
> +			&pinctrl_nrts2_default
> +			&pinctrl_ndtr2_default
> +			&pinctrl_ndsr2_default
> +			&pinctrl_ncts2_default
> +			&pinctrl_ndcd2_default
> +			&pinctrl_nri2_default>;
> +};
> +
> +&uart3 {
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	temperature-sensor@2e {
> +		compatible = "adi,adt7490";
> +		reg = <0x2e>;
> +	};
> +};
> +
> +&i2c3 {
> +	multi-master;
> +	status = "okay";
> +
> +	gpio@70 {
> +		compatible = "nxp,pca9538";
> +		reg = <0x70>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names =
> +			"presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
> +			"presence-fan5-n", "presence-fan6-n", "", "";
> +	};
> +
> +	gpio3_71:gpio@71 {

Missing space after :.

> +		compatible = "nxp,pca9538";
> +		reg = <0x71>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names =
> +			"led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
> +			"led-fan5-fault", "led-fan6-fault", "", "";
> +	};
> +};
> +
> +&fsim0 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&uhci {
> +	status = "okay";
> +};
> +
> +&sdc {
> +	status = "okay";
> +};
> +
> +/*
> + * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
> + * toggled by GPIO pins.
> + * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
> + * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
> + * a 1.8v and a 3.3v power load switch that provides signal voltage to
> + * sdhci0 bus.
> + * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
> + * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
> + * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
> + * sdhci0 signal voltage becomes 1.8v.
> + * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
> + * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
> + * as power-switch-gpio.
> + */
> +&sdhci0 {
> +	status = "okay";
> +	bus-width = <4>;
> +	max-frequency = <100000000>;
> +	sdhci-drive-type = /bits/ 8 <3>;
> +	sdhci-caps-mask = <0x7 0x0>;
> +	sdhci,wp-inverted;
> +	vmmc-supply = <&vcc_sdhci0>;
> +	vqmmc-supply = <&vccq_sdhci0>;
> +	clk-phase-sd-hs = <7>, <200>;
> +};
> +
> +&sdhci1 {
> +	status = "okay";
> +	bus-width = <4>;
> +	max-frequency = <100000000>;
> +	sdhci-drive-type = /bits/ 8 <3>;
> +	sdhci-caps-mask = <0x7 0x0>;
> +	sdhci,wp-inverted;
> +	vmmc-supply = <&vcc_sdhci1>;
> +	vqmmc-supply = <&vccq_sdhci1>;
> +	clk-phase-sd-hs = <7>, <200>;
> +};
> +
> +&gpio0 {
> +	status = "okay";
> +	gpio-line-names =
> +	/*A0-A7*/       "","","","","","","","",
> +	/*B0-B7*/       "presence-ncsi-i210-n","","","","","","","led-identify-n",
> +	/*C0-C7*/       "","","","","","","","",
> +	/*D0-D7*/       "","","","","","","","",
> +	/*E0-E7*/       "","","","","","","","",
> +	/*F0-F7*/       "","","","","","","id-button","",
> +	/*G0-G7*/       "","","led-status-green-n","led-status-amber-n","","","","",
> +	/*H0-H7*/       "","","","","","cpu-caterr","","cpu1-caterr-n",
> +	/*I0-I7*/       "","","","","","","","",
> +	/*J0-J7*/       "","","","","","","","",
> +	/*K0-K7*/       "","","","","","","","",
> +	/*L0-L7*/       "","","","","","","","",
> +	/*M0-M7*/       "","","","","","","","",
> +	/*N0-N7*/       "","","","","","","","",
> +	/*O0-O7*/       "","","","","","","nmi-button","",
> +	/*P0-P7*/       "reset-button","reset-out","power-button","power-out","","","",
> +					"led-hartbeat-n",
> +	/*Q0-Q7*/       "","","","","","","","",
> +	/*R0-R7*/       "","","","","","","","",
> +	/*S0-S7*/       "","","","","","","","",
> +	/*T0-T7*/       "","","","","","","","",
> +	/*U0-U7*/       "","","","","","","","",
> +	/*V0-V7*/       "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1",
> +					"regulator-vccq-sdhci1","sio-power-good",
> +					"led-bmc-fw-config-done-n","","",
> +	/*W0-W7*/       "","","","","","","","",
> +	/*X0-X7*/       "cpu-err2","","","","","","","",
> +	/*Y0-Y7*/       "led-power-amber","","","","","","","",
> +	/*Z0-Z7*/       "cpu-err0","cpu-err1","","","","","","";
> +	};
> +
> +&gpio1 {
> +	status = "okay";
> +};
> +
> +&kcs3 {
> +	aspeed,lpc-io-reg = <0xCA2>;
> +	status = "okay";
> +};
> +
> +&kcs4 {
> +	aspeed,lpc-io-reg = <0xCA4>;
> +	status = "okay";
> +};
> +
> +&lpc_snoop {
> +	snoop-ports = <0x80>;
> +	status = "okay";
> +};
> +

Unneeded blank line at the end.

Best regards,
Krzysztof

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
  2022-05-20 12:02 David Wang
  2022-05-20 14:31 ` Krzysztof Kozlowski
@ 2022-05-21 12:37 ` kernel test robot
  1 sibling, 0 replies; 7+ messages in thread
From: kernel test robot @ 2022-05-21 12:37 UTC (permalink / raw)
  To: David Wang, linux-kernel, robh+dt, krzysztof.kozlowski+dt, devicetree
  Cc: kbuild-all, edward_chen, David_Wang6097

Hi David,

Thank you for the patch! Yet something to improve:

[auto build test ERROR on linux/master]
[also build test ERROR on soc/for-next linus/master v5.18-rc7]
[cannot apply to joel-aspeed/for-next]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/intel-lab-lkp/linux/commits/David-Wang/ARM-dts-aspeed-Adding-Jabil-Rubypass-BMC/20220520-200353
base:   https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git 3d7285a335edaf23b699e87c528cf0b0070e3293
config: arm-allmodconfig (https://download.01.org/0day-ci/archive/20220521/202205212020.z9X7PjMn-lkp@intel.com/config)
compiler: arm-linux-gnueabi-gcc (GCC) 11.3.0
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/intel-lab-lkp/linux/commit/c8cda754bc90e31e4f419ddb60cfbedecb9e022d
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review David-Wang/ARM-dts-aspeed-Adding-Jabil-Rubypass-BMC/20220520-200353
        git checkout c8cda754bc90e31e4f419ddb60cfbedecb9e022d
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.3.0 make.cross W=1 O=build_dir ARCH=arm SHELL=/bin/bash

If you fix the issue, kindly add following tag where applicable
Reported-by: kernel test robot <lkp@intel.com>

All errors (new ones prefixed by >>):

>> Error: arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts:425.1-5 Label or path gfx not found
   FATAL ERROR: Syntax error parsing input tree

-- 
0-DAY CI Kernel Test Service
https://01.org/lkp

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
  2022-05-20 11:51 David Wang
@ 2022-05-20 14:31 ` Krzysztof Kozlowski
  0 siblings, 0 replies; 7+ messages in thread
From: Krzysztof Kozlowski @ 2022-05-20 14:31 UTC (permalink / raw)
  To: David Wang, linux-kernel, robh+dt, krzysztof.kozlowski+dt, devicetree
  Cc: edward_chen

On 20/05/2022 13:51, David Wang wrote:
> The initial introduction of the jabil server with AST2600 BMC SoC.
> 
> Signed-off-by: David Wang <David_Wang6097@jabil.com>

Why do you send a v2 second time?

Please include always changelogs under '---'.

Best regards,
Krzysztof

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
  2022-05-20 12:02 David Wang
@ 2022-05-20 14:31 ` Krzysztof Kozlowski
  2022-05-21 12:37 ` kernel test robot
  1 sibling, 0 replies; 7+ messages in thread
From: Krzysztof Kozlowski @ 2022-05-20 14:31 UTC (permalink / raw)
  To: David Wang, linux-kernel, robh+dt, krzysztof.kozlowski+dt, devicetree
  Cc: edward_chen

On 20/05/2022 14:02, David Wang wrote:
> The initial introduction of the jabil server with AST2600 BMC SoC.
> 
> Signed-off-by: David Wang <David_Wang6097@jabil.com>
> ---
>  arch/arm/boot/dts/Makefile                    |   3 +-
>  .../boot/dts/aspeed-bmc-jabil-rubypass.dts    | 479 ++++++++++++++++++
>  2 files changed, 481 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7c16f8a2b738..9c395178fc89 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>  	aspeed-bmc-tyan-s8036.dtb \
>  	aspeed-bmc-vegman-n110.dtb \
>  	aspeed-bmc-vegman-rx20.dtb \
> -	aspeed-bmc-vegman-sx20.dtb
> +	aspeed-bmc-vegman-sx20.dtb \
> +	aspeed-bmc-jabil-rubypass.dtb
> diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> new file mode 100644
> index 000000000000..5e46af30c9e9
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> @@ -0,0 +1,479 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> +	model = "Jabil rbp";
> +	compatible = "jabil,rbp", "aspeed,ast2600";

You need to document the new compatible. checkpatch should warn about
this, didn't it?

> +
> +	chosen {
> +		bootargs = "console=ttyS4,115200n8";

Please use stdout-path instead.


> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x80000000>;
> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		gfx_memory: framebuffer {
> +			size = <0x01000000>;
> +			alignment = <0x01000000>;
> +			compatible = "shared-dma-pool";
> +			reusable;
> +		};
> +	};
> +
> +	vcc_sdhci0: regulator-vcc-sdhci0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "SDHCI0 Vcc";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +
> +	vccq_sdhci0: regulator-vccq-sdhci0 {
> +		compatible = "regulator-gpio";
> +		regulator-name = "SDHCI0 VccQ";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
> +		gpios-states = <1>;
> +		states = <3300000 1>,
> +			 <1800000 0>;
> +	};
> +
> +	vcc_sdhci1: regulator-vcc-sdhci1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "SDHCI1 Vcc";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	vccq_sdhci1: regulator-vccq-sdhci1 {
> +		compatible = "regulator-gpio";
> +		regulator-name = "SDHCI1 VccQ";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
> +		gpios-states = <1>;
> +		states = <3300000 1>,
> +			 <1800000 0>;
> +	};
> +
> +	leds {
> +				compatible = "gpio-leds";

Wrong indentation.

> +
> +				identify {

Generic node names, so "led-0"

> +						default-state = "off";
> +						gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;

Missing several LED properties.

> +				};
> +
> +				status_amber {

Generic node names, no underscores in node names, so "led-1" etc.

> +						default-state = "off";
> +						gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
> +				};
> +
> +				status_green {
> +						default-state = "keep";
> +						gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
> +				};
> +
> +				status_susack {
> +						default-state = "off";
> +						gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
> +				};
> +
> +				fan1_fault{
> +						default-state = "off";
> +						gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
> +				};

Missing blank line.

> +				fan2_fault{
> +						default-state = "off";
> +				};

Ditto......

> +				fan3_fault{
> +						default-state = "off";
> +						gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
> +				};
> +				fan4_fault{
> +						default-state = "off";
> +						gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
> +				};
> +				fan5_fault{
> +						default-state = "off";
> +						gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
> +				};
> +				fan6_fault{
> +						default-state = "off";
> +						gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
> +				};
> +
> +				power_amber {
> +						default-state = "off";
> +						gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
> +				};
> +		};
> +};
> +
> +&mdio0 {
> +	status = "okay";
> +
> +	ethphy0: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mdio1 {
> +	status = "okay";
> +
> +	ethphy1: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mdio2 {
> +	status = "okay";
> +
> +	ethphy2: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mdio3 {
> +	status = "okay";
> +
> +	ethphy3: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mac0 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii-rxid";
> +	phy-handle = <&ethphy0>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii1_default>;
> +};
> +
> +

Too many blank lines.

> +&mac1 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii-rxid";
> +	phy-handle = <&ethphy1>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii2_default>;
> +};
> +
> +&mac2 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii";
> +	phy-handle = <&ethphy2>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii3_default>;
> +};
> +
> +&mac3 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii";
> +	phy-handle = <&ethphy3>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii4_default>;
> +};
> +
> +&emmc_controller {
> +	status = "okay";
> +};
> +
> +&emmc {
> +	non-removable;
> +	bus-width = <4>;
> +	max-frequency = <100000000>;
> +	clk-phase-mmc-hs200 = <9>, <225>;
> +};
> +
> +&rtc {
> +	status = "okay";
> +};
> +
> +&fmc {
> +	status = "okay";
> +	flash@0 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "bmc";
> +		spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-128.dtsi"
> +	};
> +};
> +
> +&spi1 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spi1_default>;
> +
> +	flash@0 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "pnor";
> +		spi-max-frequency = <100000000>;
> +	};
> +};
> +
> +&uart1 {
> +		status = "okay";

What's with this indentation?

> +		pinctrl-0 = <&pinctrl_txd1_default
> +					&pinctrl_rxd1_default
> +					&pinctrl_nrts1_default
> +					&pinctrl_ndtr1_default
> +					&pinctrl_ndsr1_default
> +					&pinctrl_ncts1_default
> +					&pinctrl_ndcd1_default
> +					&pinctrl_nri1_default>;
> +};
> +
> +&uart2 {
> +		status = "okay";
> +		pinctrl-0 = <&pinctrl_txd2_default
> +					&pinctrl_rxd2_default
> +					&pinctrl_nrts2_default
> +					&pinctrl_ndtr2_default
> +					&pinctrl_ndsr2_default
> +					&pinctrl_ncts2_default
> +					&pinctrl_ndcd2_default
> +					&pinctrl_nri2_default>;
> +};
> +
> +&uart3 {
> +		status = "okay";
> +};
> +
> +&uart4 {
> +		status = "okay";
> +};
> +
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	temp@2e {

generic node names, so "temperature-sensor" or just "sensor"


> +		compatible = "adi,adt7490";
> +		reg = <0x2e>;
> +	};
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	multi-master;
> +	status = "okay";
> +
> +	gpio@70 {
> +		compatible = "nxp,pca9538";
> +		reg = <0x70>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names =
> +			"presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
> +			"presence-fan5-n", "presence-fan6-n", "", "";
> +	};
> +
> +	gpio3_71:gpio@71 {
> +		compatible = "nxp,pca9538";
> +		reg = <0x71>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names =
> +			"led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
> +			"led-fan5-fault", "led-fan6-fault", "", "";
> +	};
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +};
> +
> +&i2c6 {
> +	status = "okay";
> +};
> +
> +&i2c7 {
> +	status = "okay";
> +};
> +
> +&i2c8 {
> +	status = "okay";
> +};
> +
> +&i2c9 {
> +	status = "okay";
> +};
> +
> +&i2c12 {
> +	status = "okay";
> +};
> +
> +&i2c13 {
> +	status = "okay";
> +};
> +
> +&i2c14 {
> +	status = "okay";

You enable quite a lot of empty busses. Why?


Best regards,
Krzysztof

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
@ 2022-05-20 12:02 David Wang
  2022-05-20 14:31 ` Krzysztof Kozlowski
  2022-05-21 12:37 ` kernel test robot
  0 siblings, 2 replies; 7+ messages in thread
From: David Wang @ 2022-05-20 12:02 UTC (permalink / raw)
  To: linux-kernel, robh+dt, krzysztof.kozlowski+dt, devicetree
  Cc: edward_chen, David_Wang6097

The initial introduction of the jabil server with AST2600 BMC SoC.

Signed-off-by: David Wang <David_Wang6097@jabil.com>
---
 arch/arm/boot/dts/Makefile                    |   3 +-
 .../boot/dts/aspeed-bmc-jabil-rubypass.dts    | 479 ++++++++++++++++++
 2 files changed, 481 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c16f8a2b738..9c395178fc89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-tyan-s8036.dtb \
 	aspeed-bmc-vegman-n110.dtb \
 	aspeed-bmc-vegman-rx20.dtb \
-	aspeed-bmc-vegman-sx20.dtb
+	aspeed-bmc-vegman-sx20.dtb \
+	aspeed-bmc-jabil-rubypass.dtb
diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
new file mode 100644
index 000000000000..5e46af30c9e9
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
@@ -0,0 +1,479 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Jabil rbp";
+	compatible = "jabil,rbp", "aspeed,ast2600";
+
+	chosen {
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	vcc_sdhci0: regulator-vcc-sdhci0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+
+	vccq_sdhci0: regulator-vccq-sdhci0 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	vcc_sdhci1: regulator-vcc-sdhci1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhci1: regulator-vccq-sdhci1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	leds {
+				compatible = "gpio-leds";
+
+				identify {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
+				};
+
+				status_amber {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
+				};
+
+				status_green {
+						default-state = "keep";
+						gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+				};
+
+				status_susack {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
+				};
+
+				fan1_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
+				};
+				fan2_fault{
+						default-state = "off";
+				};
+				fan3_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
+				};
+				fan4_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
+				};
+				fan5_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
+				};
+				fan6_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
+				};
+
+				power_amber {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
+				};
+		};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+
+	ethphy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+
+&mac1 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy1>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default>;
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	non-removable;
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&uart1 {
+		status = "okay";
+		pinctrl-0 = <&pinctrl_txd1_default
+					&pinctrl_rxd1_default
+					&pinctrl_nrts1_default
+					&pinctrl_ndtr1_default
+					&pinctrl_ndsr1_default
+					&pinctrl_ncts1_default
+					&pinctrl_ndcd1_default
+					&pinctrl_nri1_default>;
+};
+
+&uart2 {
+		status = "okay";
+		pinctrl-0 = <&pinctrl_txd2_default
+					&pinctrl_rxd2_default
+					&pinctrl_nrts2_default
+					&pinctrl_ndtr2_default
+					&pinctrl_ndsr2_default
+					&pinctrl_ncts2_default
+					&pinctrl_ndcd2_default
+					&pinctrl_nri2_default>;
+};
+
+&uart3 {
+		status = "okay";
+};
+
+&uart4 {
+		status = "okay";
+};
+
+
+&i2c0 {
+	status = "okay";
+
+	temp@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	multi-master;
+	status = "okay";
+
+	gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
+			"presence-fan5-n", "presence-fan6-n", "", "";
+	};
+
+	gpio3_71:gpio@71 {
+		compatible = "nxp,pca9538";
+		reg = <0x71>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
+			"led-fan5-fault", "led-fan6-fault", "", "";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&fsim0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&sdc {
+	status = "okay";
+};
+
+/*
+ * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
+ * toggled by GPIO pins.
+ * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
+ * a 1.8v and a 3.3v power load switch that provides signal voltage to
+ * sdhci0 bus.
+ * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
+ * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
+ * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
+ * sdhci0 signal voltage becomes 1.8v.
+ * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
+ * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
+ * as power-switch-gpio.
+ */
+&sdhci0 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci0>;
+	vqmmc-supply = <&vccq_sdhci0>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&sdhci1 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci1>;
+	vqmmc-supply = <&vccq_sdhci1>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+&gpio0 {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/       "","","","","","","","",
+	/*B0-B7*/       "presence-ncsi-i210-n","","","","","","","led-identify-n",
+	/*C0-C7*/       "","","","","","","","",
+	/*D0-D7*/       "","","","","","","","",
+	/*E0-E7*/       "","","","","","","","",
+	/*F0-F7*/       "","","","","","","id-button","",
+	/*G0-G7*/       "","","led-status-green-n","led-status-amber-n","","","","",
+	/*H0-H7*/       "","","","","","cpu-caterr","","cpu1-caterr-n",
+	/*I0-I7*/       "","","","","","","","",
+	/*J0-J7*/       "","","","","","","","",
+	/*K0-K7*/       "","","","","","","","",
+	/*L0-L7*/       "","","","","","","","",
+	/*M0-M7*/       "","","","","","","","",
+	/*N0-N7*/       "","","","","","","","",
+	/*O0-O7*/       "","","","","","","nmi-button","",
+	/*P0-P7*/       "reset-button","reset-out","power-button","power-out","","","","led-hartbeat-n",
+	/*Q0-Q7*/       "","","","","","","","",
+	/*R0-R7*/       "","","","","","","","",
+	/*S0-S7*/       "","","","","","","","",
+	/*T0-T7*/       "","","","","","","","",
+	/*U0-U7*/       "","","","","","","","",
+	/*V0-V7*/       "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1","regulator-vccq-sdhci1","sio-power-good","led-bmc-fw-config-done-n","","",
+	/*W0-W7*/       "","","","","","","","",
+	/*X0-X7*/       "cpu-err2","","","","","","","",
+	/*Y0-Y7*/       "led-power-amber","","","","","","","",
+	/*Z0-Z7*/       "cpu-err0","cpu-err1","","","","","","";
+	};
+
+&gpio1 {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xCA2>;
+	status = "okay";
+};
+
+&kcs4 {
+	aspeed,lpc-io-reg = <0xCA4>;
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 7+ messages in thread

* [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC
@ 2022-05-20 11:51 David Wang
  2022-05-20 14:31 ` Krzysztof Kozlowski
  0 siblings, 1 reply; 7+ messages in thread
From: David Wang @ 2022-05-20 11:51 UTC (permalink / raw)
  To: linux-kernel, robh+dt, krzysztof.kozlowski+dt, devicetree
  Cc: edward_chen, David_Wang6097

The initial introduction of the jabil server with AST2600 BMC SoC.

Signed-off-by: David Wang <David_Wang6097@jabil.com>
---
 arch/arm/boot/dts/Makefile                    |   3 +-
 .../boot/dts/aspeed-bmc-jabil-rubypass.dts    | 479 ++++++++++++++++++
 2 files changed, 481 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c16f8a2b738..9c395178fc89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-tyan-s8036.dtb \
 	aspeed-bmc-vegman-n110.dtb \
 	aspeed-bmc-vegman-rx20.dtb \
-	aspeed-bmc-vegman-sx20.dtb
+	aspeed-bmc-vegman-sx20.dtb \
+	aspeed-bmc-jabil-rubypass.dtb
diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
new file mode 100644
index 000000000000..77418895705a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
@@ -0,0 +1,479 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Jabil rbp";
+	compatible = "jabil,rbp", "aspeed,ast2600";
+
+	chosen {
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	vcc_sdhci0: regulator-vcc-sdhci0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+
+	vccq_sdhci0: regulator-vccq-sdhci0 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	vcc_sdhci1: regulator-vcc-sdhci1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhci1: regulator-vccq-sdhci1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	leds {
+				compatible = "gpio-leds";
+
+				identify {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
+				};
+
+				status_amber {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
+				};
+
+				status_green {
+						default-state = "keep";
+						gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+				};
+
+				status_susack {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
+				};
+
+				fan1_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
+				};
+				fan2_fault{
+						default-state = "off";
+		};
+				fan3_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
+				};
+				fan4_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
+				};
+				fan5_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
+				};
+				fan6_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
+				};
+
+				power_amber {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
+				};
+		};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+
+	ethphy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+
+&mac1 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy1>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default>;
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	non-removable;
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&uart1 {
+		status = "okay";
+		pinctrl-0 = <&pinctrl_txd1_default
+					&pinctrl_rxd1_default
+					&pinctrl_nrts1_default
+					&pinctrl_ndtr1_default
+					&pinctrl_ndsr1_default
+					&pinctrl_ncts1_default
+					&pinctrl_ndcd1_default
+					&pinctrl_nri1_default>;
+};
+
+&uart2 {
+		status = "okay";
+		pinctrl-0 = <&pinctrl_txd2_default
+					&pinctrl_rxd2_default
+					&pinctrl_nrts2_default
+					&pinctrl_ndtr2_default
+					&pinctrl_ndsr2_default
+					&pinctrl_ncts2_default
+					&pinctrl_ndcd2_default
+					&pinctrl_nri2_default>;
+};
+
+&uart3 {
+		status = "okay";
+};
+
+&uart4 {
+		status = "okay";
+};
+
+
+&i2c0 {
+	status = "okay";
+
+	temp@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	multi-master;
+	status = "okay";
+
+	gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
+			"presence-fan5-n", "presence-fan6-n", "", "";
+	};
+
+	gpio3_71:gpio@71 {
+		compatible = "nxp,pca9538";
+		reg = <0x71>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
+			"led-fan5-fault", "led-fan6-fault", "", "";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&fsim0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&sdc {
+	status = "okay";
+};
+
+/*
+ * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
+ * toggled by GPIO pins.
+ * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
+ * a 1.8v and a 3.3v power load switch that provides signal voltage to
+ * sdhci0 bus.
+ * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
+ * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
+ * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
+ * sdhci0 signal voltage becomes 1.8v.
+ * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
+ * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
+ * as power-switch-gpio.
+ */
+&sdhci0 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci0>;
+	vqmmc-supply = <&vccq_sdhci0>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&sdhci1 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci1>;
+	vqmmc-supply = <&vccq_sdhci1>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+&gpio0 {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/       "","","","","","","","",
+	/*B0-B7*/       "presence-ncsi-i210-n","","","","","","","led-identify-n",
+	/*C0-C7*/       "","","","","","","","",
+	/*D0-D7*/       "","","","","","","","",
+	/*E0-E7*/       "","","","","","","","",
+	/*F0-F7*/       "","","","","","","id-button","",
+	/*G0-G7*/       "","","led-status-green-n","led-status-amber-n","","","","",
+	/*H0-H7*/       "","","","","","cpu-caterr","","cpu1-caterr-n",
+	/*I0-I7*/       "","","","","","","","",
+	/*J0-J7*/       "","","","","","","","",
+	/*K0-K7*/       "","","","","","","","",
+	/*L0-L7*/       "","","","","","","","",
+	/*M0-M7*/       "","","","","","","","",
+	/*N0-N7*/       "","","","","","","","",
+	/*O0-O7*/       "","","","","","","nmi-button","",
+	/*P0-P7*/       "reset-button","reset-out","power-button","power-out","","","","led-hartbeat-n",
+	/*Q0-Q7*/       "","","","","","","","",
+	/*R0-R7*/       "","","","","","","","",
+	/*S0-S7*/       "","","","","","","","",
+	/*T0-T7*/       "","","","","","","","",
+	/*U0-U7*/       "","","","","","","","",
+	/*V0-V7*/       "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1","regulator-vccq-sdhci1","sio-power-good","led-bmc-fw-config-done-n","","",
+	/*W0-W7*/       "","","","","","","","",
+	/*X0-X7*/       "cpu-err2","","","","","","","",
+	/*Y0-Y7*/       "led-power-amber","","","","","","","",
+	/*Z0-Z7*/       "cpu-err0","cpu-err1","","","","","","";
+	};
+
+&gpio1 {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xCA2>;
+	status = "okay";
+};
+
+&kcs4 {
+	aspeed,lpc-io-reg = <0xCA4>;
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2022-05-25  6:16 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-05-25  3:42 [PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC David Wang
2022-05-25  6:16 ` Krzysztof Kozlowski
  -- strict thread matches above, loose matches on Subject: below --
2022-05-20 12:02 David Wang
2022-05-20 14:31 ` Krzysztof Kozlowski
2022-05-21 12:37 ` kernel test robot
2022-05-20 11:51 David Wang
2022-05-20 14:31 ` Krzysztof Kozlowski

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.