[PATCH u-boot-dm + u-boot-spi v2 0/7] Support SPI NORs and OF partitions in `mtd list`

[Patrice CHOTARD <patrice.chotard@foss.st.com>]

+Patrick

Hi All

I have tested this series on stm32mp1-ev1 board which embeds 1 nand and 2 identical spi-nor. 
spi-nor DT node is the following:

&qspi {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";

	flash0: mx66l51235l at 0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-rx-bus-width = <4>;
		spi-max-frequency = <108000000>;
		#address-cells = <1>;
		#size-cells = <1>;
	};

	flash1: mx66l51235l at 1 {
		compatible = "jedec,spi-nor";
		reg = <1>;
		spi-rx-bus-width = <4>;
		spi-max-frequency = <108000000>;
		#address-cells = <1>;
		#size-cells = <1>;
	};
};

As is, this series is not able to differentiate the both identical spi-nor using the MTD framework. 
Both spi-nor have the same name "mx66l51235l" as shown below, and usage of mtd command is not possible to reach
both spi-nor:

STM32MP> mtd list
List of MTD devices:
* nand0
  - type: NAND flash
  - block size: 0x40000 bytes
  - min I/O: 0x1000 bytes
  - OOB size: 224 bytes
  - OOB available: 118 bytes
  - ECC strength: 8 bits
  - ECC step size: 512 bytes
  - bitflip threshold: 6 bits
  - 0x000000000000-0x000040000000 : "nand0"
* mx66l51235l
  - device: mx66l51235l at 0
  - parent: spi at 58003000
  - driver: jedec_spi_nor
  - type: NOR flash
  - block size: 0x10000 bytes
  - min I/O: 0x1 bytes
  - 0x000000000000-0x000004000000 : "mx66l51235l"
* mx66l51235l
  - device: mx66l51235l at 1
  - parent: spi at 58003000
  - driver: jedec_spi_nor
  - type: NOR flash
  - block size: 0x10000 bytes
  - min I/O: 0x1 bytes
  - 0x000000000000-0x000004000000 : "mx66l51235l"

The following patch fix it :

@@ -2528,11 +2528,11 @@ int spi_nor_scan(struct spi_nor *nor)
 	ret = spi_nor_init_params(nor, info, &params);
 	if (ret)
 		return ret;
 
 	if (!mtd->name)
-		mtd->name = info->name;
+		mtd->name = (char *)nor->dev->name;
 	mtd->dev = nor->dev;
 	mtd->priv = nor;
 	mtd->type = MTD_NORFLASH;
 	mtd->writesize = 1;
 	mtd->flags = MTD_CAP_NORFLASH;



Now it looks like :

STM32MP> mtd list
List of MTD devices:
* nand0
  - type: NAND flash
  - block size: 0x40000 bytes
  - min I/O: 0x1000 bytes
  - OOB size: 224 bytes
  - OOB available: 118 bytes
  - ECC strength: 8 bits
  - ECC step size: 512 bytes
  - bitflip threshold: 6 bits
  - 0x000000000000-0x000040000000 : "nand0"
* mx66l51235l at 0
  - device: mx66l51235l at 0
  - parent: spi at 58003000
  - driver: jedec_spi_nor
  - type: NOR flash
  - block size: 0x10000 bytes
  - min I/O: 0x1 bytes
  - 0x000000000000-0x000004000000 : "mx66l51235l at 0"
* mx66l51235l at 1
  - device: mx66l51235l at 1
  - parent: spi at 58003000
  - driver: jedec_spi_nor
  - type: NOR flash
  - block size: 0x10000 bytes
  - min I/O: 0x1 bytes
  - 0x000000000000-0x000004000000 : "mx66l51235l at 1"
STM32MP> 

Everything goes fine, i observed one side effect regarding "sf probe" command:

STM32MP> sf probe
SF: Detected mx66l51235l at 0 with page size 256 Bytes, erase size 64 KiB, total 64 MiB
STM32MP> sf probe 1  
SF: Detected mx66l51235l at 1 with page size 256 Bytes, erase size 64 KiB, total 64 MiB

Here the flash name is mx66l51235l at 0 or mx66l51235l at 1 and no more mx66l51235l.

Thanks

Patrice



On 2/9/21 3:44 PM, Marek Beh?n wrote:
> Hello,
> 
> this is v2 of patchset that adds support for U-Boot to parse MTD
> partitions from device-tree, and also improves support for SPI NOR
> access via the `mtd` command.
> 
> Since mtd subsystem is unmaintained, who shall apply the mtd patches?
> I put an u-boot-spi tag into the subject prefix, but am not sure if
> this is correct.
> 
> Changes since v1:
> - added tests of ofnode_get_addr_size_index() and
>   ofnode_get_addr_size_index_notrans() as requested by Simon
> - the last patch now probes SPI NORs in both versions of
>   mtd_probe_devices(), that is when MTDPARTS is enabled or disabled
> 
> Marek
> 
> Marek Beh?n (7):
>   dm: core: add test for ofnode_get_addr_size_index()
>   dm: core: add non-translating version of ofnode_get_addr_size_index()
>   mtd: add support for parsing partitions defined in OF
>   mtd: spi-nor: allow registering multiple MTDs when DM is enabled
>   mtd: spi-nor: fill-in mtd->dev member
>   mtd: remove mtd_probe function
>   mtd: probe SPI NOR devices in mtd_probe_devices()
> 
>  drivers/core/ofnode.c          |  19 ++++-
>  drivers/mtd/mtd-uclass.c       |  15 ----
>  drivers/mtd/mtd_uboot.c        | 129 ++++++++++++++++++++-------------
>  drivers/mtd/mtdpart.c          |  60 +++++++++++++++
>  drivers/mtd/spi/sf_internal.h  |   4 +-
>  drivers/mtd/spi/sf_mtd.c       |  19 ++++-
>  drivers/mtd/spi/sf_probe.c     |   6 +-
>  drivers/mtd/spi/spi-nor-core.c |   1 +
>  drivers/mtd/spi/spi-nor-tiny.c |   1 +
>  include/dm/ofnode.h            |  17 +++++
>  include/linux/mtd/mtd.h        |   9 +++
>  include/mtd.h                  |   1 -
>  test/dm/ofnode.c               |  29 ++++++++
>  13 files changed, 236 insertions(+), 74 deletions(-)
>