[PATCH 0/4] serial: uartps: Dynamic allocation

[PATCH 0/4] serial: uartps: Dynamic allocation

[Michal Simek]

Hi,

this is the initial version before next step which is move
uart_register_driver to probe function.
I was able to get rid of static array with uart_port structures.
It was wired with console which is also fixed.
And the next step is the most complicated one handle .nr in uart_driver
structure in more generic way.

I am sending these patches as v1. RFC was sent in past
(https://www.spinics.net/lists/linux-serial/msg27106.html)
and I promised to wait till Geert's
"serial: xuartps: Fix out-of-bounds access through DT
alias" (sha1: e7d75e18d0fc3f7193b65282b651f980c778d935) is applied.

Thanks,
Michal


Michal Simek (4):
  serial: uartps: Remove console_initcall from the driver
  serial: uartps: Use dynamic array for console port
  serial: uartps: Move cnds_uart_get_port to probe
  serial: uartps: Remove static port array

 drivers/tty/serial/xilinx_uartps.c | 102 +++++++++++------------------
 1 file changed, 40 insertions(+), 62 deletions(-)

-- 
2.17.0

[PATCH 0/4] serial: uartps: Dynamic allocation

[Michal Simek]

Hi,

this is the initial version before next step which is move
uart_register_driver to probe function.
I was able to get rid of static array with uart_port structures.
It was wired with console which is also fixed.
And the next step is the most complicated one handle .nr in uart_driver
structure in more generic way.

I am sending these patches as v1. RFC was sent in past
(https://www.spinics.net/lists/linux-serial/msg27106.html)
and I promised to wait till Geert's
"serial: xuartps: Fix out-of-bounds access through DT
alias" (sha1: e7d75e18d0fc3f7193b65282b651f980c778d935) is applied.

Thanks,
Michal


Michal Simek (4):
  serial: uartps: Remove console_initcall from the driver
  serial: uartps: Use dynamic array for console port
  serial: uartps: Move cnds_uart_get_port to probe
  serial: uartps: Remove static port array

 drivers/tty/serial/xilinx_uartps.c | 102 +++++++++++------------------
 1 file changed, 40 insertions(+), 62 deletions(-)

-- 
2.17.0

[PATCH 1/4] serial: uartps: Remove console_initcall from the driver

[Michal Simek]

register_console() is called from
uart_add_one_port()->uart_configure_port()
that's why register_console() is called twice.

This patch remove console_initcall to call register_console() only from
one location.

Also based on my tests cdns_uart_console_setup() is not called
from the first register_console() call.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

I am not quite sure about this because console_initcall is called
early but I can see any difference in usage.
pl011 is not calling this but others are doing it.
---
 drivers/tty/serial/xilinx_uartps.c | 14 --------------
 1 file changed, 14 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index bd72dd843338..932210331484 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1293,20 +1293,6 @@ static struct console cdns_uart_console = {
 	.index	= -1, /* Specified on the cmdline (e.g. console=ttyPS ) */
 	.data	= &cdns_uart_uart_driver,
 };
-
-/**
- * cdns_uart_console_init - Initialization call
- *
- * Return: 0 on success, negative errno otherwise
- */
-static int __init cdns_uart_console_init(void)
-{
-	register_console(&cdns_uart_console);
-	return 0;
-}
-
-console_initcall(cdns_uart_console_init);
-
 #endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */
 
 static struct uart_driver cdns_uart_uart_driver = {
-- 
2.17.0

[PATCH 1/4] serial: uartps: Remove console_initcall from the driver

[Michal Simek]

register_console() is called from
uart_add_one_port()->uart_configure_port()
that's why register_console() is called twice.

This patch remove console_initcall to call register_console() only from
one location.

Also based on my tests cdns_uart_console_setup() is not called
from the first register_console() call.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

I am not quite sure about this because console_initcall is called
early but I can see any difference in usage.
pl011 is not calling this but others are doing it.
---
 drivers/tty/serial/xilinx_uartps.c | 14 --------------
 1 file changed, 14 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index bd72dd843338..932210331484 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1293,20 +1293,6 @@ static struct console cdns_uart_console = {
 	.index	= -1, /* Specified on the cmdline (e.g. console=ttyPS ) */
 	.data	= &cdns_uart_uart_driver,
 };
-
-/**
- * cdns_uart_console_init - Initialization call
- *
- * Return: 0 on success, negative errno otherwise
- */
-static int __init cdns_uart_console_init(void)
-{
-	register_console(&cdns_uart_console);
-	return 0;
-}
-
-console_initcall(cdns_uart_console_init);
-
 #endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */
 
 static struct uart_driver cdns_uart_uart_driver = {
-- 
2.17.0

[PATCH 2/4] serial: uartps: Use dynamic array for console port

[Michal Simek]

Driver console functions are using pointer to static array with fixed
size. There can be only one serial console at the time which is found
by register_console(). register_console() is filling cons->index to
port->line value.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

 drivers/tty/serial/xilinx_uartps.c | 29 ++++++++++++++++++++++++-----
 1 file changed, 24 insertions(+), 5 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 932210331484..789423d081ed 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1206,6 +1206,10 @@ OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p8", cdns_early_console_setup);
 OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p12", cdns_early_console_setup);
 OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
 
+
+/* Static pointer to console port */
+static struct uart_port *console_port;
+
 /**
  * cdns_uart_console_write - perform write operation
  * @co: Console handle
@@ -1215,7 +1219,7 @@ OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
 static void cdns_uart_console_write(struct console *co, const char *s,
 				unsigned int count)
 {
-	struct uart_port *port = &cdns_uart_port[co->index];
+	struct uart_port *port = console_port;
 	unsigned long flags;
 	unsigned int imr, ctrl;
 	int locked = 1;
@@ -1261,15 +1265,13 @@ static void cdns_uart_console_write(struct console *co, const char *s,
  */
 static int __init cdns_uart_console_setup(struct console *co, char *options)
 {
-	struct uart_port *port = &cdns_uart_port[co->index];
+	struct uart_port *port = console_port;
+
 	int baud = 9600;
 	int bits = 8;
 	int parity = 'n';
 	int flow = 'n';
 
-	if (co->index < 0 || co->index >= CDNS_UART_NR_PORTS)
-		return -EINVAL;
-
 	if (!port->membase) {
 		pr_debug("console on " CDNS_UART_TTY_NAME "%i not present\n",
 			 co->index);
@@ -1565,6 +1567,17 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
+#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
+	/*
+	 * If console hasn't been found yet try to assign this port
+	 * because it is required to be assigned for console setup function.
+	 * If register_console() don't assign value, then console_port pointer
+	 * is cleanup.
+	 */
+	if (cdns_uart_uart_driver.cons->index == -1)
+		console_port = port;
+#endif
+
 	rc = uart_add_one_port(&cdns_uart_uart_driver, port);
 	if (rc) {
 		dev_err(&pdev->dev,
@@ -1572,6 +1585,12 @@ static int cdns_uart_probe(struct platform_device *pdev)
 		goto err_out_pm_disable;
 	}
 
+#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
+	/* This is not port which is used for console that's why clean it up */
+	if (cdns_uart_uart_driver.cons->index == -1)
+		console_port = NULL;
+#endif
+
 	return 0;
 
 err_out_pm_disable:
-- 
2.17.0

[PATCH 2/4] serial: uartps: Use dynamic array for console port

[Michal Simek]

Driver console functions are using pointer to static array with fixed
size. There can be only one serial console at the time which is found
by register_console(). register_console() is filling cons->index to
port->line value.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

 drivers/tty/serial/xilinx_uartps.c | 29 ++++++++++++++++++++++++-----
 1 file changed, 24 insertions(+), 5 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 932210331484..789423d081ed 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1206,6 +1206,10 @@ OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p8", cdns_early_console_setup);
 OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p12", cdns_early_console_setup);
 OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
 
+
+/* Static pointer to console port */
+static struct uart_port *console_port;
+
 /**
  * cdns_uart_console_write - perform write operation
  * @co: Console handle
@@ -1215,7 +1219,7 @@ OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
 static void cdns_uart_console_write(struct console *co, const char *s,
 				unsigned int count)
 {
-	struct uart_port *port = &cdns_uart_port[co->index];
+	struct uart_port *port = console_port;
 	unsigned long flags;
 	unsigned int imr, ctrl;
 	int locked = 1;
@@ -1261,15 +1265,13 @@ static void cdns_uart_console_write(struct console *co, const char *s,
  */
 static int __init cdns_uart_console_setup(struct console *co, char *options)
 {
-	struct uart_port *port = &cdns_uart_port[co->index];
+	struct uart_port *port = console_port;
+
 	int baud = 9600;
 	int bits = 8;
 	int parity = 'n';
 	int flow = 'n';
 
-	if (co->index < 0 || co->index >= CDNS_UART_NR_PORTS)
-		return -EINVAL;
-
 	if (!port->membase) {
 		pr_debug("console on " CDNS_UART_TTY_NAME "%i not present\n",
 			 co->index);
@@ -1565,6 +1567,17 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
+#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
+	/*
+	 * If console hasn't been found yet try to assign this port
+	 * because it is required to be assigned for console setup function.
+	 * If register_console() don't assign value, then console_port pointer
+	 * is cleanup.
+	 */
+	if (cdns_uart_uart_driver.cons->index == -1)
+		console_port = port;
+#endif
+
 	rc = uart_add_one_port(&cdns_uart_uart_driver, port);
 	if (rc) {
 		dev_err(&pdev->dev,
@@ -1572,6 +1585,12 @@ static int cdns_uart_probe(struct platform_device *pdev)
 		goto err_out_pm_disable;
 	}
 
+#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
+	/* This is not port which is used for console that's why clean it up */
+	if (cdns_uart_uart_driver.cons->index == -1)
+		console_port = NULL;
+#endif
+
 	return 0;
 
 err_out_pm_disable:
-- 
2.17.0

[PATCH 3/4] serial: uartps: Move cnds_uart_get_port to probe

[Michal Simek]

c&p this function to probe as preparation for removing
cdns_uart_port[] static array.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

 drivers/tty/serial/xilinx_uartps.c | 61 ++++++++++--------------------
 1 file changed, 21 insertions(+), 40 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 789423d081ed..f7d527a1c532 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1099,43 +1099,6 @@ static const struct uart_ops cdns_uart_ops = {
 
 static struct uart_port cdns_uart_port[CDNS_UART_NR_PORTS];
 
-/**
- * cdns_uart_get_port - Configure the port from platform device resource info
- * @id: Port id
- *
- * Return: a pointer to a uart_port or NULL for failure
- */
-static struct uart_port *cdns_uart_get_port(int id)
-{
-	struct uart_port *port;
-
-	/* Try the given port id if failed use default method */
-	if (id < CDNS_UART_NR_PORTS && cdns_uart_port[id].mapbase != 0) {
-		/* Find the next unused port */
-		for (id = 0; id < CDNS_UART_NR_PORTS; id++)
-			if (cdns_uart_port[id].mapbase == 0)
-				break;
-	}
-
-	if (id >= CDNS_UART_NR_PORTS)
-		return NULL;
-
-	port = &cdns_uart_port[id];
-
-	/* At this point, we've got an empty uart_port struct, initialize it */
-	spin_lock_init(&port->lock);
-	port->membase	= NULL;
-	port->irq	= 0;
-	port->type	= PORT_UNKNOWN;
-	port->iotype	= UPIO_MEM32;
-	port->flags	= UPF_BOOT_AUTOCONF;
-	port->ops	= &cdns_uart_ops;
-	port->fifosize	= CDNS_UART_FIFO_SIZE;
-	port->line	= id;
-	port->dev	= NULL;
-	return port;
-}
-
 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
 /**
  * cdns_uart_console_wait_tx - Wait for the TX to be full
@@ -1540,15 +1503,33 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	if (id < 0)
 		id = 0;
 
-	/* Initialize the port structure */
-	port = cdns_uart_get_port(id);
+	/* Try the given port id if failed use default method */
+	if (id < CDNS_UART_NR_PORTS && cdns_uart_port[id].mapbase != 0) {
+		/* Find the next unused port */
+		for (id = 0; id < CDNS_UART_NR_PORTS; id++)
+			if (cdns_uart_port[id].mapbase == 0)
+				break;
+	}
 
-	if (!port) {
+	port = &cdns_uart_port[id];
+	if (!port || id >= CDNS_UART_NR_PORTS) {
 		dev_err(&pdev->dev, "Cannot get uart_port structure\n");
 		rc = -ENODEV;
 		goto err_out_notif_unreg;
 	}
 
+	/* At this point, we've got an empty uart_port struct, initialize it */
+	spin_lock_init(&port->lock);
+	port->membase	= NULL;
+	port->irq	= 0;
+	port->type	= PORT_UNKNOWN;
+	port->iotype	= UPIO_MEM32;
+	port->flags	= UPF_BOOT_AUTOCONF;
+	port->ops	= &cdns_uart_ops;
+	port->fifosize	= CDNS_UART_FIFO_SIZE;
+	port->line	= id;
+	port->dev	= NULL;
+
 	/*
 	 * Register the port.
 	 * This function also registers this device with the tty layer
-- 
2.17.0

[PATCH 3/4] serial: uartps: Move cnds_uart_get_port to probe

[Michal Simek]

c&p this function to probe as preparation for removing
cdns_uart_port[] static array.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

 drivers/tty/serial/xilinx_uartps.c | 61 ++++++++++--------------------
 1 file changed, 21 insertions(+), 40 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 789423d081ed..f7d527a1c532 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1099,43 +1099,6 @@ static const struct uart_ops cdns_uart_ops = {
 
 static struct uart_port cdns_uart_port[CDNS_UART_NR_PORTS];
 
-/**
- * cdns_uart_get_port - Configure the port from platform device resource info
- * @id: Port id
- *
- * Return: a pointer to a uart_port or NULL for failure
- */
-static struct uart_port *cdns_uart_get_port(int id)
-{
-	struct uart_port *port;
-
-	/* Try the given port id if failed use default method */
-	if (id < CDNS_UART_NR_PORTS && cdns_uart_port[id].mapbase != 0) {
-		/* Find the next unused port */
-		for (id = 0; id < CDNS_UART_NR_PORTS; id++)
-			if (cdns_uart_port[id].mapbase == 0)
-				break;
-	}
-
-	if (id >= CDNS_UART_NR_PORTS)
-		return NULL;
-
-	port = &cdns_uart_port[id];
-
-	/* At this point, we've got an empty uart_port struct, initialize it */
-	spin_lock_init(&port->lock);
-	port->membase	= NULL;
-	port->irq	= 0;
-	port->type	= PORT_UNKNOWN;
-	port->iotype	= UPIO_MEM32;
-	port->flags	= UPF_BOOT_AUTOCONF;
-	port->ops	= &cdns_uart_ops;
-	port->fifosize	= CDNS_UART_FIFO_SIZE;
-	port->line	= id;
-	port->dev	= NULL;
-	return port;
-}
-
 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
 /**
  * cdns_uart_console_wait_tx - Wait for the TX to be full
@@ -1540,15 +1503,33 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	if (id < 0)
 		id = 0;
 
-	/* Initialize the port structure */
-	port = cdns_uart_get_port(id);
+	/* Try the given port id if failed use default method */
+	if (id < CDNS_UART_NR_PORTS && cdns_uart_port[id].mapbase != 0) {
+		/* Find the next unused port */
+		for (id = 0; id < CDNS_UART_NR_PORTS; id++)
+			if (cdns_uart_port[id].mapbase == 0)
+				break;
+	}
 
-	if (!port) {
+	port = &cdns_uart_port[id];
+	if (!port || id >= CDNS_UART_NR_PORTS) {
 		dev_err(&pdev->dev, "Cannot get uart_port structure\n");
 		rc = -ENODEV;
 		goto err_out_notif_unreg;
 	}
 
+	/* At this point, we've got an empty uart_port struct, initialize it */
+	spin_lock_init(&port->lock);
+	port->membase	= NULL;
+	port->irq	= 0;
+	port->type	= PORT_UNKNOWN;
+	port->iotype	= UPIO_MEM32;
+	port->flags	= UPF_BOOT_AUTOCONF;
+	port->ops	= &cdns_uart_ops;
+	port->fifosize	= CDNS_UART_FIFO_SIZE;
+	port->line	= id;
+	port->dev	= NULL;
+
 	/*
 	 * Register the port.
 	 * This function also registers this device with the tty layer
-- 
2.17.0

[PATCH 4/4] serial: uartps: Remove static port array

[Michal Simek]

Allocate uart port structure dynamically.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

 drivers/tty/serial/xilinx_uartps.c | 16 ++++------------
 1 file changed, 4 insertions(+), 12 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f7d527a1c532..0fc9de20843c 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1097,8 +1097,6 @@ static const struct uart_ops cdns_uart_ops = {
 #endif
 };
 
-static struct uart_port cdns_uart_port[CDNS_UART_NR_PORTS];
-
 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
 /**
  * cdns_uart_console_wait_tx - Wait for the TX to be full
@@ -1438,6 +1436,9 @@ static int cdns_uart_probe(struct platform_device *pdev)
 			GFP_KERNEL);
 	if (!cdns_uart_data)
 		return -ENOMEM;
+	port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
 
 	match = of_match_node(cdns_uart_of_match, pdev->dev.of_node);
 	if (match && match->data) {
@@ -1503,16 +1504,7 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	if (id < 0)
 		id = 0;
 
-	/* Try the given port id if failed use default method */
-	if (id < CDNS_UART_NR_PORTS && cdns_uart_port[id].mapbase != 0) {
-		/* Find the next unused port */
-		for (id = 0; id < CDNS_UART_NR_PORTS; id++)
-			if (cdns_uart_port[id].mapbase == 0)
-				break;
-	}
-
-	port = &cdns_uart_port[id];
-	if (!port || id >= CDNS_UART_NR_PORTS) {
+	if (id >= CDNS_UART_NR_PORTS) {
 		dev_err(&pdev->dev, "Cannot get uart_port structure\n");
 		rc = -ENODEV;
 		goto err_out_notif_unreg;
-- 
2.17.0

[PATCH 4/4] serial: uartps: Remove static port array

[Michal Simek]

Allocate uart port structure dynamically.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
---

 drivers/tty/serial/xilinx_uartps.c | 16 ++++------------
 1 file changed, 4 insertions(+), 12 deletions(-)

diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f7d527a1c532..0fc9de20843c 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1097,8 +1097,6 @@ static const struct uart_ops cdns_uart_ops = {
 #endif
 };
 
-static struct uart_port cdns_uart_port[CDNS_UART_NR_PORTS];
-
 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
 /**
  * cdns_uart_console_wait_tx - Wait for the TX to be full
@@ -1438,6 +1436,9 @@ static int cdns_uart_probe(struct platform_device *pdev)
 			GFP_KERNEL);
 	if (!cdns_uart_data)
 		return -ENOMEM;
+	port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
 
 	match = of_match_node(cdns_uart_of_match, pdev->dev.of_node);
 	if (match && match->data) {
@@ -1503,16 +1504,7 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	if (id < 0)
 		id = 0;
 
-	/* Try the given port id if failed use default method */
-	if (id < CDNS_UART_NR_PORTS && cdns_uart_port[id].mapbase != 0) {
-		/* Find the next unused port */
-		for (id = 0; id < CDNS_UART_NR_PORTS; id++)
-			if (cdns_uart_port[id].mapbase == 0)
-				break;
-	}
-
-	port = &cdns_uart_port[id];
-	if (!port || id >= CDNS_UART_NR_PORTS) {
+	if (id >= CDNS_UART_NR_PORTS) {
 		dev_err(&pdev->dev, "Cannot get uart_port structure\n");
 		rc = -ENODEV;
 		goto err_out_notif_unreg;
-- 
2.17.0