Re: module snd-atiixp issue with suspend/hibernate/resume

[Ryan Dunn <oryandunn.ml@gmail.com>]

I apologize for the list spam.  I didn't realize that this bit is only set
when the led is on.  So with that here are diffs of the regs with and
without mute enabled, before and after suspend.
Before suspend:
diff regs_w-quirk.txt regs_w-quirk+mute.txt
2c2
< 0:02 = 1e1e
---
> 0:02 = 9e1e
20c20
< 0:26 = 000f
---
> 0:26 = 800f

After resume:
diff regs_w-quirk_after_resume.txt regs_w-quirk_after_resume+mute.txt
2c2
< 0:02 = 1e1e
---
> 0:02 = 9e1e
20c20
< 0:26 = 000f
---
> 0:26 = 800f

So it looks as if the registers are all ok after a resume, but the LED
doesn't turn back on.

Ryan

On Thu, Apr 30, 2009 at 10:12 PM, Ryan Dunn <oryandunn.ml@gmail.com> wrote:

> Here is a diff of the registers before & after resume:
> diff regs_before_suspend.txt regs_after_suspend.txt
> 58c58
> < 0:72 = 0000
> ---
> > 0:72 = 5000
>
> In the ac97_codec.h file, AC97_POWERDOWN = 0x26.  Does this respond to 0:26
> in the regs file?  If so, it doesn't appear that bit 0x8000 is ever set, but
> the mute LED works.
>
>
> On Thu, Apr 30, 2009 at 7:49 AM, Ryan Dunn <oryandunn.ml@gmail.com> wrote:
>
>> Thanks Takashi,
>>
>> I did a bit more testing last night.  The LED does work after a reboot (I
>> don't know what I was doing that I thought it didn't).  It also retains
>> state after a reboot if I muted it before the reboot.  One thing I noticed,
>> if I have it muted when I suspend, on resume, it looks like the mute led
>> flashes back on for a split second, then turns off.  Maybe the resume code
>> is overwriting the register?  I'll start digging through that code tonight.
>>
>> Ryan
>>
>>
>> On Thu, Apr 30, 2009 at 1:53 AM, Takashi Iwai <tiwai@suse.de> wrote:
>>
>>> At Thu, 30 Apr 2009 00:43:02 -0400,
>>> Ryan Dunn wrote:
>>> >
>>> > Thanks Lee,
>>> >
>>> > I grabbed the kernel source from the repos and started perusing the
>>> code.  It
>>> > looks like when the module is installed, the call chain starts in
>>> atiixp.c and
>>> > moves into ac97/ac97_codec.c via a call to snd_ac97_tune_hardware()
>>> which
>>> > ultimately twiddles a bit in the AC97_POWERDOWN register.  I'm not sure
>>> yet if
>>> > the suspend method properly saves this register on suspend or not;
>>>
>>> It should.  snd_ac97_resume() writes the cached value.
>>> Check /proc/asound/card0/codec97#0/ac97#*+regs files before and after
>>> suspend.  You can change the codec register value directly via proc
>>> file, e.g.
>>>    # echo 0x12 0x1234 > /proc/asound/card0/codec97#0/ac97#0-0+regs
>>> (only when you build with the debug option).
>>>
>>> The bit 0x8000 of the power-down register should correspond to LED.
>>>
>>>
>>> Takashi
>>>
>>> > or if the
>>> > same call chain needs to be repeated on a resume.  I appreciate your
>>> quick and
>>> > relevant answer.  When I get time, I'll start adding some debug
>>> printouts to
>>> > try this out.
>>> >
>>> > Also, the struct ac97_quirk ac97_quirks[] array has a couple of entries
>>> in it
>>> > currently (in the atiixp.c file).  How do I get the subvender/subdevice
>>> id's
>>> > for my system (I didn't seem to have luck with lspci, unless I'm not
>>> looking
>>> > in the right fields)?  Would it be possible to edit the driver so that
>>> an
>>> > explict module option would not be needed on my hardware?
>>> >
>>> > Thanks,
>>> > Ryan
>>> >
>>> > On Wed, Apr 29, 2009 at 10:42 PM, Lee Revell <rlrevell@joe-job.com>
>>> wrote:
>>> >
>>> >     On Wed, Apr 29, 2009 at 12:06 AM, Ryan Dunn <oryandunn.ml@
>>> gmail.com>
>>> >     wrote:
>>> >     > I have a Compaq V2000 laptop with the ATI IXP chipset and make
>>> use of
>>> >     the
>>> >     > snd-atiixp module.  The laptop needs to have the ac97_quirk
>>> option set
>>> >     to 7
>>> >     > to enable the mute LED.  After setting this option in the
>>> >     > /etc/modprobe.d/options.conf file, the mute LED works after a
>>> reboot.
>>> >     > However, after a resume from suspend or hibernate, the mute LED
>>> does not
>>> >     > work.  The alsa-info.sh script reports that the quirk is still
>>> set with
>>> >     7.
>>> >     > At this point a reboot will NOT fix the problem.  The only way to
>>> fix it
>>> >     is
>>> >     > to remove and reinsert the module with modprobe.
>>> >     >
>>> >     > This is on a fresh Ubuntu 9.04 install.  Any ideas?  I wasn't
>>> sure if
>>> >     this
>>> >     > should be reported here or on the kernel list.  I saw a similar
>>> issue
>>> >     with
>>> >     > the ac97_quirk on the kernel list and they were referred here.
>>>  I'm a
>>> >     > software developer, so I'd be willing to try ideas/possible
>>> solutions if
>>> >     you
>>> >     > have them.
>>> >
>>> >     Get the Ubuntu source code for the package that owns that ALSA
>>> driver,
>>> >     find the place in the driver's initialization code where
>>> ac97_quirk=7
>>> >     is handled, then check the driver's suspend and resume callbacks
>>> and
>>> >     make sure the suspend callback is correctly saving the LED state
>>> and
>>> >     that the resume callback is re-initializing the LED from the saved
>>> >     state in the same way the init code does.  grep and printk() are
>>> your
>>> >     friends ;-)
>>> >
>>> >     HTH,
>>> >
>>> >     Lee
>>> >
>>> >
>>> _______________________________________________
>>> Alsa-devel mailing list
>>> Alsa-devel@alsa-project.org
>>> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
>>>
>>
>>
>