* [PATCH v3 0/5] arm64: dts: Update IOT2050 boards
@ 2021-09-09 19:41 ` Jan Kiszka
0 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
This enhances the DTs for the IOT2050, primarily by added support for
upcoming Production Generation 2 (PG2) and by ordering the MMC devices
consistently across variants.
Changes in 3:
- move mmc alias back into board DTs
- add patch to enable R5F cores for rproc
Changes in v2:
- move mmc alias to SoC level
- split up into PG2 preparation and addition patch
- add link to product homepage
Jan
Jan Kiszka (5):
arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F
cores
arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
arm64: dts: ti: iot2050: Add support for product generation 2 boards
arch/arm64/boot/dts/ti/Makefile | 2 +
.../dts/ti/k3-am65-iot2050-common-pg1.dtsi | 46 +++++++++++++++
.../dts/ti/k3-am65-iot2050-common-pg2.dtsi | 51 +++++++++++++++++
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 39 +++++++++----
...ts => k3-am6528-iot2050-basic-common.dtsi} | 12 +---
.../dts/ti/k3-am6528-iot2050-basic-pg2.dts | 24 ++++++++
.../boot/dts/ti/k3-am6528-iot2050-basic.dts | 56 +++----------------
...=> k3-am6548-iot2050-advanced-common.dtsi} | 8 +--
.../dts/ti/k3-am6548-iot2050-advanced-pg2.dts | 29 ++++++++++
.../dts/ti/k3-am6548-iot2050-advanced.dts | 50 +++--------------
10 files changed, 199 insertions(+), 118 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
copy arch/arm64/boot/dts/ti/{k3-am6528-iot2050-basic.dts => k3-am6528-iot2050-basic-common.dtsi} (80%)
create mode 100644 arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
copy arch/arm64/boot/dts/ti/{k3-am6548-iot2050-advanced.dts => k3-am6548-iot2050-advanced-common.dtsi} (85%)
create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread* [PATCH v3 1/5] arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-09 19:41 ` Jan Kiszka
-1 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
This ensures that the SD card will remain mmc0 across Basic and Advanced
devices, also avoiding surprises for users coming from the downstream
kernels.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 1008e9162ba2..6261ca8ee2d8 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -17,6 +17,8 @@
/ {
aliases {
spi0 = &mcu_spi0;
+ mmc0 = &sdhci1;
+ mmc1 = &sdhci0;
};
chosen {
--
2.31.1
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v3 1/5] arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
@ 2021-09-09 19:41 ` Jan Kiszka
0 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
This ensures that the SD card will remain mmc0 across Basic and Advanced
devices, also avoiding surprises for users coming from the downstream
kernels.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 1008e9162ba2..6261ca8ee2d8 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -17,6 +17,8 @@
/ {
aliases {
spi0 = &mcu_spi0;
+ mmc0 = &sdhci1;
+ mmc1 = &sdhci0;
};
chosen {
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* Re: [PATCH v3 1/5] arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-15 2:40 ` Aswath Govindraju
-1 siblings, 0 replies; 24+ messages in thread
From: Aswath Govindraju @ 2021-09-15 2:40 UTC (permalink / raw)
To: Jan Kiszka, Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
On 10/09/21 1:11 am, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> This ensures that the SD card will remain mmc0 across Basic and Advanced
> devices, also avoiding surprises for users coming from the downstream
> kernels.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
> arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 1008e9162ba2..6261ca8ee2d8 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -17,6 +17,8 @@
> / {
> aliases {
> spi0 = &mcu_spi0;
> + mmc0 = &sdhci1;
> + mmc1 = &sdhci0;
> };
>
> chosen {
>
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v3 1/5] arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
@ 2021-09-15 2:40 ` Aswath Govindraju
0 siblings, 0 replies; 24+ messages in thread
From: Aswath Govindraju @ 2021-09-15 2:40 UTC (permalink / raw)
To: Jan Kiszka, Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
On 10/09/21 1:11 am, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> This ensures that the SD card will remain mmc0 across Basic and Advanced
> devices, also avoiding surprises for users coming from the downstream
> kernels.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
> arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 1008e9162ba2..6261ca8ee2d8 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -17,6 +17,8 @@
> / {
> aliases {
> spi0 = &mcu_spi0;
> + mmc0 = &sdhci1;
> + mmc1 = &sdhci0;
> };
>
> chosen {
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 2/5] arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-09 19:41 ` Jan Kiszka
-1 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
The IOT2050 devices described so far are using SR1.0 silicon, thus do
not have the additional PRUs of the ICSSG of the SR2.0. Disable them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 24 +++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 6261ca8ee2d8..58c8e64d5885 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -716,3 +716,27 @@ &icssg1_mdio {
&icssg2_mdio {
status = "disabled";
};
+
+&tx_pru0_0 {
+ status = "disabled";
+};
+
+&tx_pru0_1 {
+ status = "disabled";
+};
+
+&tx_pru1_0 {
+ status = "disabled";
+};
+
+&tx_pru1_1 {
+ status = "disabled";
+};
+
+&tx_pru2_0 {
+ status = "disabled";
+};
+
+&tx_pru2_1 {
+ status = "disabled";
+};
--
2.31.1
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v3 2/5] arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
@ 2021-09-09 19:41 ` Jan Kiszka
0 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
The IOT2050 devices described so far are using SR1.0 silicon, thus do
not have the additional PRUs of the ICSSG of the SR2.0. Disable them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 24 +++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 6261ca8ee2d8..58c8e64d5885 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -716,3 +716,27 @@ &icssg1_mdio {
&icssg2_mdio {
status = "disabled";
};
+
+&tx_pru0_0 {
+ status = "disabled";
+};
+
+&tx_pru0_1 {
+ status = "disabled";
+};
+
+&tx_pru1_0 {
+ status = "disabled";
+};
+
+&tx_pru1_1 {
+ status = "disabled";
+};
+
+&tx_pru2_0 {
+ status = "disabled";
+};
+
+&tx_pru2_1 {
+ status = "disabled";
+};
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* Re: [PATCH v3 2/5] arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-15 2:43 ` Aswath Govindraju
-1 siblings, 0 replies; 24+ messages in thread
From: Aswath Govindraju @ 2021-09-15 2:43 UTC (permalink / raw)
To: Jan Kiszka, Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
On 10/09/21 1:11 am, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> The IOT2050 devices described so far are using SR1.0 silicon, thus do
> not have the additional PRUs of the ICSSG of the SR2.0. Disable them.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
> .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 24 +++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 6261ca8ee2d8..58c8e64d5885 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -716,3 +716,27 @@ &icssg1_mdio {
> &icssg2_mdio {
> status = "disabled";
> };
> +
> +&tx_pru0_0 {
> + status = "disabled";
> +};
> +
> +&tx_pru0_1 {
> + status = "disabled";
> +};
> +
> +&tx_pru1_0 {
> + status = "disabled";
> +};
> +
> +&tx_pru1_1 {
> + status = "disabled";
> +};
> +
> +&tx_pru2_0 {
> + status = "disabled";
> +};
> +
> +&tx_pru2_1 {
> + status = "disabled";
> +};
>
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v3 2/5] arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
@ 2021-09-15 2:43 ` Aswath Govindraju
0 siblings, 0 replies; 24+ messages in thread
From: Aswath Govindraju @ 2021-09-15 2:43 UTC (permalink / raw)
To: Jan Kiszka, Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
On 10/09/21 1:11 am, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> The IOT2050 devices described so far are using SR1.0 silicon, thus do
> not have the additional PRUs of the ICSSG of the SR2.0. Disable them.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
> .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 24 +++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 6261ca8ee2d8..58c8e64d5885 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -716,3 +716,27 @@ &icssg1_mdio {
> &icssg2_mdio {
> status = "disabled";
> };
> +
> +&tx_pru0_0 {
> + status = "disabled";
> +};
> +
> +&tx_pru0_1 {
> + status = "disabled";
> +};
> +
> +&tx_pru1_0 {
> + status = "disabled";
> +};
> +
> +&tx_pru1_1 {
> + status = "disabled";
> +};
> +
> +&tx_pru2_0 {
> + status = "disabled";
> +};
> +
> +&tx_pru2_1 {
> + status = "disabled";
> +};
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 3/5] arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-09 19:41 ` Jan Kiszka
-1 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
Analogously to the am654-base-board, configure the mailboxes for the the
two R5F cores, add them and the already existing memory carve-outs to
the related MCU nodes. Allows to load applications under Linux onto the
cores, e.g. the RTI watchdog firmware.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 26 +++++++++++++++++--
1 file changed, 24 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 58c8e64d5885..b29537088289 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -658,11 +658,21 @@ &pcie1_ep {
};
&mailbox0_cluster0 {
- status = "disabled";
+ interrupts = <436>;
+
+ mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
+ ti,mbox-tx = <1 0 0>;
+ ti,mbox-rx = <0 0 0>;
+ };
};
&mailbox0_cluster1 {
- status = "disabled";
+ interrupts = <432>;
+
+ mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
+ ti,mbox-tx = <1 0 0>;
+ ti,mbox-rx = <0 0 0>;
+ };
};
&mailbox0_cluster2 {
@@ -705,6 +715,18 @@ &mailbox0_cluster11 {
status = "disabled";
};
+&mcu_r5fss0_core0 {
+ memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+ <&mcu_r5fss0_core0_memory_region>;
+ mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
+};
+
+&mcu_r5fss0_core1 {
+ memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
+ <&mcu_r5fss0_core1_memory_region>;
+ mboxes = <&mailbox0_cluster1 &mbox_mcu_r5fss0_core1>;
+};
+
&icssg0_mdio {
status = "disabled";
};
--
2.31.1
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v3 3/5] arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
@ 2021-09-09 19:41 ` Jan Kiszka
0 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
Analogously to the am654-base-board, configure the mailboxes for the the
two R5F cores, add them and the already existing memory carve-outs to
the related MCU nodes. Allows to load applications under Linux onto the
cores, e.g. the RTI watchdog firmware.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 26 +++++++++++++++++--
1 file changed, 24 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 58c8e64d5885..b29537088289 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -658,11 +658,21 @@ &pcie1_ep {
};
&mailbox0_cluster0 {
- status = "disabled";
+ interrupts = <436>;
+
+ mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
+ ti,mbox-tx = <1 0 0>;
+ ti,mbox-rx = <0 0 0>;
+ };
};
&mailbox0_cluster1 {
- status = "disabled";
+ interrupts = <432>;
+
+ mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
+ ti,mbox-tx = <1 0 0>;
+ ti,mbox-rx = <0 0 0>;
+ };
};
&mailbox0_cluster2 {
@@ -705,6 +715,18 @@ &mailbox0_cluster11 {
status = "disabled";
};
+&mcu_r5fss0_core0 {
+ memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+ <&mcu_r5fss0_core0_memory_region>;
+ mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
+};
+
+&mcu_r5fss0_core1 {
+ memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
+ <&mcu_r5fss0_core1_memory_region>;
+ mboxes = <&mailbox0_cluster1 &mbox_mcu_r5fss0_core1>;
+};
+
&icssg0_mdio {
status = "disabled";
};
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* Re: [PATCH v3 3/5] arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-14 20:16 ` Nishanth Menon
-1 siblings, 0 replies; 24+ messages in thread
From: Nishanth Menon @ 2021-09-14 20:16 UTC (permalink / raw)
To: Jan Kiszka
Cc: Tero Kristo, Rob Herring, linux-arm-kernel, linux-kernel,
devicetree, Bao Cheng Su, Chao Zeng
On 21:41-20210909, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> Analogously to the am654-base-board, configure the mailboxes for the the
s/the the/the -> could you checkpatch and dtbs_checks please?
> two R5F cores, add them and the already existing memory carve-outs to
> the related MCU nodes. Allows to load applications under Linux onto the
> cores, e.g. the RTI watchdog firmware.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
> .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 26 +++++++++++++++++--
> 1 file changed, 24 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 58c8e64d5885..b29537088289 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -658,11 +658,21 @@ &pcie1_ep {
> };
>
> &mailbox0_cluster0 {
> - status = "disabled";
> + interrupts = <436>;
> +
> + mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster1 {
> - status = "disabled";
> + interrupts = <432>;
> +
> + mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster2 {
> @@ -705,6 +715,18 @@ &mailbox0_cluster11 {
> status = "disabled";
> };
>
> +&mcu_r5fss0_core0 {
> + memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
> + <&mcu_r5fss0_core0_memory_region>;
> + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
> +};
> +
> +&mcu_r5fss0_core1 {
> + memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
> + <&mcu_r5fss0_core1_memory_region>;
> + mboxes = <&mailbox0_cluster1 &mbox_mcu_r5fss0_core1>;
> +};
> +
> &icssg0_mdio {
> status = "disabled";
> };
> --
> 2.31.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v3 3/5] arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
@ 2021-09-14 20:16 ` Nishanth Menon
0 siblings, 0 replies; 24+ messages in thread
From: Nishanth Menon @ 2021-09-14 20:16 UTC (permalink / raw)
To: Jan Kiszka
Cc: Tero Kristo, Rob Herring, linux-arm-kernel, linux-kernel,
devicetree, Bao Cheng Su, Chao Zeng
On 21:41-20210909, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> Analogously to the am654-base-board, configure the mailboxes for the the
s/the the/the -> could you checkpatch and dtbs_checks please?
> two R5F cores, add them and the already existing memory carve-outs to
> the related MCU nodes. Allows to load applications under Linux onto the
> cores, e.g. the RTI watchdog firmware.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
> .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 26 +++++++++++++++++--
> 1 file changed, 24 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 58c8e64d5885..b29537088289 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -658,11 +658,21 @@ &pcie1_ep {
> };
>
> &mailbox0_cluster0 {
> - status = "disabled";
> + interrupts = <436>;
> +
> + mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster1 {
> - status = "disabled";
> + interrupts = <432>;
> +
> + mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster2 {
> @@ -705,6 +715,18 @@ &mailbox0_cluster11 {
> status = "disabled";
> };
>
> +&mcu_r5fss0_core0 {
> + memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
> + <&mcu_r5fss0_core0_memory_region>;
> + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
> +};
> +
> +&mcu_r5fss0_core1 {
> + memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
> + <&mcu_r5fss0_core1_memory_region>;
> + mboxes = <&mailbox0_cluster1 &mbox_mcu_r5fss0_core1>;
> +};
> +
> &icssg0_mdio {
> status = "disabled";
> };
> --
> 2.31.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v3 3/5] arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-15 15:28 ` Vignesh Raghavendra
-1 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2021-09-15 15:28 UTC (permalink / raw)
To: Jan Kiszka, Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
On 9/10/21 1:11 AM, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> Analogously to the am654-base-board, configure the mailboxes for the the
> two R5F cores, add them and the already existing memory carve-outs to
> the related MCU nodes. Allows to load applications under Linux onto the
> cores, e.g. the RTI watchdog firmware.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---
> .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 26 +++++++++++++++++--
> 1 file changed, 24 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 58c8e64d5885..b29537088289 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -658,11 +658,21 @@ &pcie1_ep {
> };
>
> &mailbox0_cluster0 {
> - status = "disabled";
> + interrupts = <436>;
> +
> + mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster1 {
> - status = "disabled";
> + interrupts = <432>;
> +
> + mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster2 {
> @@ -705,6 +715,18 @@ &mailbox0_cluster11 {
> status = "disabled";
> };
>
> +&mcu_r5fss0_core0 {
> + memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
> + <&mcu_r5fss0_core0_memory_region>;
> + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
> +};
> +
> +&mcu_r5fss0_core1 {
> + memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
> + <&mcu_r5fss0_core1_memory_region>;
> + mboxes = <&mailbox0_cluster1 &mbox_mcu_r5fss0_core1>;
> +};
> +
> &icssg0_mdio {
> status = "disabled";
> };
>
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v3 3/5] arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
@ 2021-09-15 15:28 ` Vignesh Raghavendra
0 siblings, 0 replies; 24+ messages in thread
From: Vignesh Raghavendra @ 2021-09-15 15:28 UTC (permalink / raw)
To: Jan Kiszka, Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
On 9/10/21 1:11 AM, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> Analogously to the am654-base-board, configure the mailboxes for the the
> two R5F cores, add them and the already existing memory carve-outs to
> the related MCU nodes. Allows to load applications under Linux onto the
> cores, e.g. the RTI watchdog firmware.
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---
> .../boot/dts/ti/k3-am65-iot2050-common.dtsi | 26 +++++++++++++++++--
> 1 file changed, 24 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> index 58c8e64d5885..b29537088289 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
> @@ -658,11 +658,21 @@ &pcie1_ep {
> };
>
> &mailbox0_cluster0 {
> - status = "disabled";
> + interrupts = <436>;
> +
> + mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster1 {
> - status = "disabled";
> + interrupts = <432>;
> +
> + mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
> + ti,mbox-tx = <1 0 0>;
> + ti,mbox-rx = <0 0 0>;
> + };
> };
>
> &mailbox0_cluster2 {
> @@ -705,6 +715,18 @@ &mailbox0_cluster11 {
> status = "disabled";
> };
>
> +&mcu_r5fss0_core0 {
> + memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
> + <&mcu_r5fss0_core0_memory_region>;
> + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
> +};
> +
> +&mcu_r5fss0_core1 {
> + memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
> + <&mcu_r5fss0_core1_memory_region>;
> + mboxes = <&mailbox0_cluster1 &mbox_mcu_r5fss0_core1>;
> +};
> +
> &icssg0_mdio {
> status = "disabled";
> };
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 4/5] arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-09 19:41 ` Jan Kiszka
-1 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
The current IOT2050 devices are Product Generation 1 (PG1), using SR1.0
AM65x silicon. Upcoming PG2 devices will use SR2.x SoCs and will
therefore need separate device trees. Prepare for that by factoring out
common bits that will be shared across both generations.
At this chance, drop a link to the product homepage to in the top-level
dts files.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
.../dts/ti/k3-am65-iot2050-common-pg1.dtsi | 46 +++++++++++++++
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 35 +-----------
...ts => k3-am6528-iot2050-basic-common.dtsi} | 12 +---
.../boot/dts/ti/k3-am6528-iot2050-basic.dts | 56 +++----------------
...=> k3-am6548-iot2050-advanced-common.dtsi} | 8 +--
.../dts/ti/k3-am6548-iot2050-advanced.dts | 50 +++--------------
6 files changed, 67 insertions(+), 140 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
copy arch/arm64/boot/dts/ti/{k3-am6528-iot2050-basic.dts => k3-am6528-iot2050-basic-common.dtsi} (80%)
copy arch/arm64/boot/dts/ti/{k3-am6548-iot2050-advanced.dts => k3-am6548-iot2050-advanced-common.dtsi} (85%)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
new file mode 100644
index 000000000000..51f902fa35a7
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2021
+ *
+ * Authors:
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Basic and Advanced variants, PG1
+ */
+
+&dss {
+ assigned-clocks = <&k3_clks 67 2>;
+ assigned-clock-parents = <&k3_clks 67 5>;
+};
+
+&serdes0 {
+ status = "disabled";
+};
+
+&sdhci1 {
+ no-1-8-v;
+};
+
+&tx_pru0_0 {
+ status = "disabled";
+};
+
+&tx_pru0_1 {
+ status = "disabled";
+};
+
+&tx_pru1_0 {
+ status = "disabled";
+};
+
+&tx_pru1_1 {
+ status = "disabled";
+};
+
+&tx_pru2_0 {
+ status = "disabled";
+};
+
+&tx_pru2_1 {
+ status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index b29537088289..65da226847f4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -4,13 +4,11 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * Common bits of the IOT2050 Basic and Advanced variants
+ * Common bits of the IOT2050 Basic and Advanced variants, PG1 and PG2
*/
-/dts-v1/;
-
#include "k3-am654.dtsi"
#include <dt-bindings/phy/phy.h>
@@ -557,7 +555,6 @@ &sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
disable-wp;
- no-1-8-v;
};
&usb0 {
@@ -631,10 +628,6 @@ dpi_out: endpoint {
};
};
-&serdes0 {
- status = "disabled";
-};
-
&pcie0_rc {
status = "disabled";
};
@@ -738,27 +731,3 @@ &icssg1_mdio {
&icssg2_mdio {
status = "disabled";
};
-
-&tx_pru0_0 {
- status = "disabled";
-};
-
-&tx_pru0_1 {
- status = "disabled";
-};
-
-&tx_pru1_0 {
- status = "disabled";
-};
-
-&tx_pru1_1 {
- status = "disabled";
-};
-
-&tx_pru2_0 {
- status = "disabled";
-};
-
-&tx_pru2_1 {
- status = "disabled";
-};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
similarity index 80%
copy from arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
copy to arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
index 94bb5dd39122..4a9bf7d7c07d 100644
--- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
@@ -4,20 +4,14 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6528-based (dual-core) IOT2050 Basic variant
- * 1 GB RAM, no eMMC, main_uart0 on connector X30
+ * Common bits of the IOT2050 Basic variant, PG1 and PG2
*/
-/dts-v1/;
-
#include "k3-am65-iot2050-common.dtsi"
/ {
- compatible = "siemens,iot2050-basic", "ti,am654";
- model = "SIMATIC IOT2050 Basic";
-
memory@80000000 {
device_type = "memory";
/* 1G RAM */
@@ -61,6 +55,6 @@ &main_uart0 {
};
&mcu_r5fss0 {
- /* lock-step mode not supported on this board */
+ /* lock-step mode not supported on Basic boards */
ti,cluster-mode = <0>;
};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
index 94bb5dd39122..87928ff28214 100644
--- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
@@ -4,63 +4,21 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6528-based (dual-core) IOT2050 Basic variant
+ * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 1
* 1 GB RAM, no eMMC, main_uart0 on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
*/
/dts-v1/;
-#include "k3-am65-iot2050-common.dtsi"
+#include "k3-am6528-iot2050-basic-common.dtsi"
+#include "k3-am65-iot2050-common-pg1.dtsi"
/ {
compatible = "siemens,iot2050-basic", "ti,am654";
model = "SIMATIC IOT2050 Basic";
-
- memory@80000000 {
- device_type = "memory";
- /* 1G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
- };
-
- cpus {
- cpu-map {
- /delete-node/ cluster1;
- };
- /delete-node/ cpu@100;
- /delete-node/ cpu@101;
- };
-
- /delete-node/ l2-cache1;
-};
-
-/* eMMC */
-&sdhci0 {
- status = "disabled";
-};
-
-&main_pmx0 {
- main_uart0_pins_default: main-uart0-pins-default {
- pinctrl-single,pins = <
- AM65X_IOPAD(0x01e4, PIN_INPUT, 0) /* (AF11) UART0_RXD */
- AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0) /* (AE11) UART0_TXD */
- AM65X_IOPAD(0x01ec, PIN_INPUT, 0) /* (AG11) UART0_CTSn */
- AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0) /* (AD11) UART0_RTSn */
- AM65X_IOPAD(0x0188, PIN_INPUT, 1) /* (D25) UART0_DCDn */
- AM65X_IOPAD(0x018c, PIN_INPUT, 1) /* (B26) UART0_DSRn */
- AM65X_IOPAD(0x0190, PIN_OUTPUT, 1) /* (A24) UART0_DTRn */
- AM65X_IOPAD(0x0194, PIN_INPUT, 1) /* (E24) UART0_RIN */
- >;
- };
-};
-
-&main_uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart0_pins_default>;
-};
-
-&mcu_r5fss0 {
- /* lock-step mode not supported on this board */
- ti,cluster-mode = <0>;
};
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
similarity index 85%
copy from arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
copy to arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
index ec9617c13cdb..d25e8b26187f 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
@@ -4,10 +4,9 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6548-based (quad-core) IOT2050 Advanced variant
- * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ * Common bits of the IOT2050 Advanced variant, PG1 and PG2
*/
/dts-v1/;
@@ -15,9 +14,6 @@
#include "k3-am65-iot2050-common.dtsi"
/ {
- compatible = "siemens,iot2050-advanced", "ti,am654";
- model = "SIMATIC IOT2050 Advanced";
-
memory@80000000 {
device_type = "memory";
/* 2G RAM */
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
index ec9617c13cdb..077f165bdc68 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
@@ -4,57 +4,21 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6548-based (quad-core) IOT2050 Advanced variant
+ * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 1
* 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
*/
/dts-v1/;
-#include "k3-am65-iot2050-common.dtsi"
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg1.dtsi"
/ {
compatible = "siemens,iot2050-advanced", "ti,am654";
model = "SIMATIC IOT2050 Advanced";
-
- memory@80000000 {
- device_type = "memory";
- /* 2G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
- };
-};
-
-&main_pmx0 {
- main_mmc0_pins_default: main-mmc0-pins-default {
- pinctrl-single,pins = <
- AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */
- AM65X_IOPAD(0x01ac, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */
- AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */
- AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */
- AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */
- AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */
- AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */
- AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */
- AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */
- AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */
- AM65X_IOPAD(0x01b8, PIN_OUTPUT_PULLUP, 7) /* (B23) MMC0_SDWP */
- AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP, 0) /* (A23) MMC0_SDCD */
- AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */
- >;
- };
-};
-
-/* eMMC */
-&sdhci0 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_mmc0_pins_default>;
- bus-width = <8>;
- non-removable;
- ti,driver-strength-ohm = <50>;
- disable-wp;
-};
-
-&main_uart0 {
- status = "disabled";
};
--
2.31.1
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v3 4/5] arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
@ 2021-09-09 19:41 ` Jan Kiszka
0 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
The current IOT2050 devices are Product Generation 1 (PG1), using SR1.0
AM65x silicon. Upcoming PG2 devices will use SR2.x SoCs and will
therefore need separate device trees. Prepare for that by factoring out
common bits that will be shared across both generations.
At this chance, drop a link to the product homepage to in the top-level
dts files.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
.../dts/ti/k3-am65-iot2050-common-pg1.dtsi | 46 +++++++++++++++
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 35 +-----------
...ts => k3-am6528-iot2050-basic-common.dtsi} | 12 +---
.../boot/dts/ti/k3-am6528-iot2050-basic.dts | 56 +++----------------
...=> k3-am6548-iot2050-advanced-common.dtsi} | 8 +--
.../dts/ti/k3-am6548-iot2050-advanced.dts | 50 +++--------------
6 files changed, 67 insertions(+), 140 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
copy arch/arm64/boot/dts/ti/{k3-am6528-iot2050-basic.dts => k3-am6528-iot2050-basic-common.dtsi} (80%)
copy arch/arm64/boot/dts/ti/{k3-am6548-iot2050-advanced.dts => k3-am6548-iot2050-advanced-common.dtsi} (85%)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
new file mode 100644
index 000000000000..51f902fa35a7
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2021
+ *
+ * Authors:
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Basic and Advanced variants, PG1
+ */
+
+&dss {
+ assigned-clocks = <&k3_clks 67 2>;
+ assigned-clock-parents = <&k3_clks 67 5>;
+};
+
+&serdes0 {
+ status = "disabled";
+};
+
+&sdhci1 {
+ no-1-8-v;
+};
+
+&tx_pru0_0 {
+ status = "disabled";
+};
+
+&tx_pru0_1 {
+ status = "disabled";
+};
+
+&tx_pru1_0 {
+ status = "disabled";
+};
+
+&tx_pru1_1 {
+ status = "disabled";
+};
+
+&tx_pru2_0 {
+ status = "disabled";
+};
+
+&tx_pru2_1 {
+ status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index b29537088289..65da226847f4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -4,13 +4,11 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * Common bits of the IOT2050 Basic and Advanced variants
+ * Common bits of the IOT2050 Basic and Advanced variants, PG1 and PG2
*/
-/dts-v1/;
-
#include "k3-am654.dtsi"
#include <dt-bindings/phy/phy.h>
@@ -557,7 +555,6 @@ &sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
disable-wp;
- no-1-8-v;
};
&usb0 {
@@ -631,10 +628,6 @@ dpi_out: endpoint {
};
};
-&serdes0 {
- status = "disabled";
-};
-
&pcie0_rc {
status = "disabled";
};
@@ -738,27 +731,3 @@ &icssg1_mdio {
&icssg2_mdio {
status = "disabled";
};
-
-&tx_pru0_0 {
- status = "disabled";
-};
-
-&tx_pru0_1 {
- status = "disabled";
-};
-
-&tx_pru1_0 {
- status = "disabled";
-};
-
-&tx_pru1_1 {
- status = "disabled";
-};
-
-&tx_pru2_0 {
- status = "disabled";
-};
-
-&tx_pru2_1 {
- status = "disabled";
-};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
similarity index 80%
copy from arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
copy to arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
index 94bb5dd39122..4a9bf7d7c07d 100644
--- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
@@ -4,20 +4,14 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6528-based (dual-core) IOT2050 Basic variant
- * 1 GB RAM, no eMMC, main_uart0 on connector X30
+ * Common bits of the IOT2050 Basic variant, PG1 and PG2
*/
-/dts-v1/;
-
#include "k3-am65-iot2050-common.dtsi"
/ {
- compatible = "siemens,iot2050-basic", "ti,am654";
- model = "SIMATIC IOT2050 Basic";
-
memory@80000000 {
device_type = "memory";
/* 1G RAM */
@@ -61,6 +55,6 @@ &main_uart0 {
};
&mcu_r5fss0 {
- /* lock-step mode not supported on this board */
+ /* lock-step mode not supported on Basic boards */
ti,cluster-mode = <0>;
};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
index 94bb5dd39122..87928ff28214 100644
--- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
@@ -4,63 +4,21 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6528-based (dual-core) IOT2050 Basic variant
+ * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 1
* 1 GB RAM, no eMMC, main_uart0 on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
*/
/dts-v1/;
-#include "k3-am65-iot2050-common.dtsi"
+#include "k3-am6528-iot2050-basic-common.dtsi"
+#include "k3-am65-iot2050-common-pg1.dtsi"
/ {
compatible = "siemens,iot2050-basic", "ti,am654";
model = "SIMATIC IOT2050 Basic";
-
- memory@80000000 {
- device_type = "memory";
- /* 1G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
- };
-
- cpus {
- cpu-map {
- /delete-node/ cluster1;
- };
- /delete-node/ cpu@100;
- /delete-node/ cpu@101;
- };
-
- /delete-node/ l2-cache1;
-};
-
-/* eMMC */
-&sdhci0 {
- status = "disabled";
-};
-
-&main_pmx0 {
- main_uart0_pins_default: main-uart0-pins-default {
- pinctrl-single,pins = <
- AM65X_IOPAD(0x01e4, PIN_INPUT, 0) /* (AF11) UART0_RXD */
- AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0) /* (AE11) UART0_TXD */
- AM65X_IOPAD(0x01ec, PIN_INPUT, 0) /* (AG11) UART0_CTSn */
- AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0) /* (AD11) UART0_RTSn */
- AM65X_IOPAD(0x0188, PIN_INPUT, 1) /* (D25) UART0_DCDn */
- AM65X_IOPAD(0x018c, PIN_INPUT, 1) /* (B26) UART0_DSRn */
- AM65X_IOPAD(0x0190, PIN_OUTPUT, 1) /* (A24) UART0_DTRn */
- AM65X_IOPAD(0x0194, PIN_INPUT, 1) /* (E24) UART0_RIN */
- >;
- };
-};
-
-&main_uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart0_pins_default>;
-};
-
-&mcu_r5fss0 {
- /* lock-step mode not supported on this board */
- ti,cluster-mode = <0>;
};
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
similarity index 85%
copy from arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
copy to arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
index ec9617c13cdb..d25e8b26187f 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
@@ -4,10 +4,9 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6548-based (quad-core) IOT2050 Advanced variant
- * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ * Common bits of the IOT2050 Advanced variant, PG1 and PG2
*/
/dts-v1/;
@@ -15,9 +14,6 @@
#include "k3-am65-iot2050-common.dtsi"
/ {
- compatible = "siemens,iot2050-advanced", "ti,am654";
- model = "SIMATIC IOT2050 Advanced";
-
memory@80000000 {
device_type = "memory";
/* 2G RAM */
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
index ec9617c13cdb..077f165bdc68 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
@@ -4,57 +4,21 @@
*
* Authors:
* Le Jin <le.jin@siemens.com>
- * Jan Kiszka <jan.kiszk@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
*
- * AM6548-based (quad-core) IOT2050 Advanced variant
+ * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 1
* 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
*/
/dts-v1/;
-#include "k3-am65-iot2050-common.dtsi"
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg1.dtsi"
/ {
compatible = "siemens,iot2050-advanced", "ti,am654";
model = "SIMATIC IOT2050 Advanced";
-
- memory@80000000 {
- device_type = "memory";
- /* 2G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
- };
-};
-
-&main_pmx0 {
- main_mmc0_pins_default: main-mmc0-pins-default {
- pinctrl-single,pins = <
- AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */
- AM65X_IOPAD(0x01ac, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */
- AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */
- AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */
- AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */
- AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */
- AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */
- AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */
- AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */
- AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */
- AM65X_IOPAD(0x01b8, PIN_OUTPUT_PULLUP, 7) /* (B23) MMC0_SDWP */
- AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP, 0) /* (A23) MMC0_SDCD */
- AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */
- >;
- };
-};
-
-/* eMMC */
-&sdhci0 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_mmc0_pins_default>;
- bus-width = <8>;
- non-removable;
- ti,driver-strength-ohm = <50>;
- disable-wp;
-};
-
-&main_uart0 {
- status = "disabled";
};
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* Re: [PATCH v3 4/5] arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-14 20:17 ` Nishanth Menon
-1 siblings, 0 replies; 24+ messages in thread
From: Nishanth Menon @ 2021-09-14 20:17 UTC (permalink / raw)
To: Jan Kiszka
Cc: Tero Kristo, Rob Herring, linux-arm-kernel, linux-kernel,
devicetree, Bao Cheng Su, Chao Zeng
On 21:41-20210909, Jan Kiszka wrote:
[..]
> copy from arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
> copy to arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
> index ec9617c13cdb..d25e8b26187f 100644
> --- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
> @@ -4,10 +4,9 @@
> *
> * Authors:
> * Le Jin <le.jin@siemens.com>
> - * Jan Kiszka <jan.kiszk@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
^^ please call that email ID out in the commit message as well.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v3 4/5] arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
@ 2021-09-14 20:17 ` Nishanth Menon
0 siblings, 0 replies; 24+ messages in thread
From: Nishanth Menon @ 2021-09-14 20:17 UTC (permalink / raw)
To: Jan Kiszka
Cc: Tero Kristo, Rob Herring, linux-arm-kernel, linux-kernel,
devicetree, Bao Cheng Su, Chao Zeng
On 21:41-20210909, Jan Kiszka wrote:
[..]
> copy from arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
> copy to arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
> index ec9617c13cdb..d25e8b26187f 100644
> --- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
> @@ -4,10 +4,9 @@
> *
> * Authors:
> * Le Jin <le.jin@siemens.com>
> - * Jan Kiszka <jan.kiszk@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
^^ please call that email ID out in the commit message as well.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v3 5/5] arm64: dts: ti: iot2050: Add support for product generation 2 boards
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-09 19:41 ` Jan Kiszka
-1 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
This adds the devices trees for IOT2050 Product Generation 2 (PG2)
boards. We have Basic and an Advanced variants again, differing in
number of cores, RAM size, availability of eMMC and further details.
The major difference to PG1 is the used silicon revision (SR2.x on
PG2).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
.../dts/ti/k3-am65-iot2050-common-pg2.dtsi | 51 +++++++++++++++++++
.../dts/ti/k3-am6528-iot2050-basic-pg2.dts | 24 +++++++++
.../dts/ti/k3-am6548-iot2050-advanced-pg2.dts | 29 +++++++++++
4 files changed, 106 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
create mode 100644 arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index d56c742f5a10..41a4bc96e6bd 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -8,7 +8,9 @@
dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
new file mode 100644
index 000000000000..2323628b0444
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2021
+ *
+ * Authors:
+ * Chao Zeng <chao.zeng@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Basic and Advanced variants, PG2
+ */
+
+&main_pmx0 {
+ cp2102n_reset_pin_default: cp2102n_reset_pin_default {
+ pinctrl-single,pins = <
+ /* (AF12) GPIO1_24, used as cp2102 reset */
+ AM65X_IOPAD(0x01e0, PIN_OUTPUT, 7)
+ >;
+ };
+};
+
+&main_gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp2102n_reset_pin_default>;
+ gpio-line-names =
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "CP2102N-RESET";
+};
+
+&dss {
+ /* Workaround needed to get DP clock of 154Mhz */
+ assigned-clocks = <&k3_clks 67 0>;
+};
+
+&serdes0 {
+ assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
+ assigned-clock-parents = <&k3_clks 153 7>, <&k3_clks 153 4>;
+};
+
+&dwc3_0 {
+ assigned-clock-parents = <&k3_clks 151 4>, /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
+ <&k3_clks 151 8>; /* set PIPE3_TXB_CLK to WIZ8B2M4VSB */
+ phys = <&serdes0 PHY_TYPE_USB3 0>;
+ phy-names = "usb3-phy";
+};
+
+&usb0_phy {
+ maximum-speed = "super-speed";
+ snps,dis-u1-entry-quirk;
+ snps,dis-u2-entry-quirk;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
new file mode 100644
index 000000000000..c62549a4b436
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ * Le Jin <le.jin@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 2
+ * 1 GB RAM, no eMMC, main_uart0 on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+/dts-v1/;
+
+#include "k3-am6528-iot2050-basic-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+ compatible = "siemens,iot2050-basic-pg2", "ti,am654";
+ model = "SIMATIC IOT2050 Basic PG2";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
new file mode 100644
index 000000000000..f00dc86d01b9
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ * Le Jin <le.jin@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 2
+ * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+/dts-v1/;
+
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+ compatible = "siemens,iot2050-advanced-pg2", "ti,am654";
+ model = "SIMATIC IOT2050 Advanced PG2";
+};
+
+&mcu_r5fss0 {
+ /* lock-step mode not supported on this board */
+ ti,cluster-mode = <0>;
+};
--
2.31.1
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v3 5/5] arm64: dts: ti: iot2050: Add support for product generation 2 boards
@ 2021-09-09 19:41 ` Jan Kiszka
0 siblings, 0 replies; 24+ messages in thread
From: Jan Kiszka @ 2021-09-09 19:41 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: linux-arm-kernel, linux-kernel, devicetree, Bao Cheng Su, Chao Zeng
From: Jan Kiszka <jan.kiszka@siemens.com>
This adds the devices trees for IOT2050 Product Generation 2 (PG2)
boards. We have Basic and an Advanced variants again, differing in
number of cores, RAM size, availability of eMMC and further details.
The major difference to PG1 is the used silicon revision (SR2.x on
PG2).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
.../dts/ti/k3-am65-iot2050-common-pg2.dtsi | 51 +++++++++++++++++++
.../dts/ti/k3-am6528-iot2050-basic-pg2.dts | 24 +++++++++
.../dts/ti/k3-am6548-iot2050-advanced-pg2.dts | 29 +++++++++++
4 files changed, 106 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
create mode 100644 arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index d56c742f5a10..41a4bc96e6bd 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -8,7 +8,9 @@
dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
new file mode 100644
index 000000000000..2323628b0444
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2021
+ *
+ * Authors:
+ * Chao Zeng <chao.zeng@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Basic and Advanced variants, PG2
+ */
+
+&main_pmx0 {
+ cp2102n_reset_pin_default: cp2102n_reset_pin_default {
+ pinctrl-single,pins = <
+ /* (AF12) GPIO1_24, used as cp2102 reset */
+ AM65X_IOPAD(0x01e0, PIN_OUTPUT, 7)
+ >;
+ };
+};
+
+&main_gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp2102n_reset_pin_default>;
+ gpio-line-names =
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "CP2102N-RESET";
+};
+
+&dss {
+ /* Workaround needed to get DP clock of 154Mhz */
+ assigned-clocks = <&k3_clks 67 0>;
+};
+
+&serdes0 {
+ assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
+ assigned-clock-parents = <&k3_clks 153 7>, <&k3_clks 153 4>;
+};
+
+&dwc3_0 {
+ assigned-clock-parents = <&k3_clks 151 4>, /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
+ <&k3_clks 151 8>; /* set PIPE3_TXB_CLK to WIZ8B2M4VSB */
+ phys = <&serdes0 PHY_TYPE_USB3 0>;
+ phy-names = "usb3-phy";
+};
+
+&usb0_phy {
+ maximum-speed = "super-speed";
+ snps,dis-u1-entry-quirk;
+ snps,dis-u2-entry-quirk;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
new file mode 100644
index 000000000000..c62549a4b436
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ * Le Jin <le.jin@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 2
+ * 1 GB RAM, no eMMC, main_uart0 on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+/dts-v1/;
+
+#include "k3-am6528-iot2050-basic-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+ compatible = "siemens,iot2050-basic-pg2", "ti,am654";
+ model = "SIMATIC IOT2050 Basic PG2";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
new file mode 100644
index 000000000000..f00dc86d01b9
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ * Le Jin <le.jin@siemens.com>
+ * Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 2
+ * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+/dts-v1/;
+
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+ compatible = "siemens,iot2050-advanced-pg2", "ti,am654";
+ model = "SIMATIC IOT2050 Advanced PG2";
+};
+
+&mcu_r5fss0 {
+ /* lock-step mode not supported on this board */
+ ti,cluster-mode = <0>;
+};
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* Re: [PATCH v3 5/5] arm64: dts: ti: iot2050: Add support for product generation 2 boards
2021-09-09 19:41 ` Jan Kiszka
@ 2021-09-14 20:15 ` Nishanth Menon
-1 siblings, 0 replies; 24+ messages in thread
From: Nishanth Menon @ 2021-09-14 20:15 UTC (permalink / raw)
To: Jan Kiszka
Cc: Tero Kristo, Rob Herring, linux-arm-kernel, linux-kernel,
devicetree, Bao Cheng Su, Chao Zeng
On 21:41-20210909, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> This adds the devices trees for IOT2050 Product Generation 2 (PG2)
> boards. We have Basic and an Advanced variants again, differing in
> number of cores, RAM size, availability of eMMC and further details.
> The major difference to PG1 is the used silicon revision (SR2.x on
> PG2).
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
> arch/arm64/boot/dts/ti/Makefile | 2 +
> .../dts/ti/k3-am65-iot2050-common-pg2.dtsi | 51 +++++++++++++++++++
> .../dts/ti/k3-am6528-iot2050-basic-pg2.dts | 24 +++++++++
> .../dts/ti/k3-am6548-iot2050-advanced-pg2.dts | 29 +++++++++++
> 4 files changed, 106 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
> create mode 100644 arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
> create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index d56c742f5a10..41a4bc96e6bd 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -8,7 +8,9 @@
>
> dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
> new file mode 100644
> index 000000000000..2323628b0444
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
> @@ -0,0 +1,51 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) Siemens AG, 2021
> + *
> + * Authors:
> + * Chao Zeng <chao.zeng@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
> + *
> + * Common bits of the IOT2050 Basic and Advanced variants, PG2
> + */
> +
> +&main_pmx0 {
> + cp2102n_reset_pin_default: cp2102n_reset_pin_default {
cp2102n_reset_pin_default: cp2102n-reset-pin-default
> + pinctrl-single,pins = <
> + /* (AF12) GPIO1_24, used as cp2102 reset */
> + AM65X_IOPAD(0x01e0, PIN_OUTPUT, 7)
> + >;
> + };
> +};
> +
> +&main_gpio1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp2102n_reset_pin_default>;
> + gpio-line-names =
> + "", "", "", "", "", "", "", "", "", "",
> + "", "", "", "", "", "", "", "", "", "",
> + "", "", "", "", "CP2102N-RESET";
> +};
> +
> +&dss {
> + /* Workaround needed to get DP clock of 154Mhz */
> + assigned-clocks = <&k3_clks 67 0>;
> +};
> +
> +&serdes0 {
> + assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
> + assigned-clock-parents = <&k3_clks 153 7>, <&k3_clks 153 4>;
> +};
> +
> +&dwc3_0 {
> + assigned-clock-parents = <&k3_clks 151 4>, /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
> + <&k3_clks 151 8>; /* set PIPE3_TXB_CLK to WIZ8B2M4VSB */
> + phys = <&serdes0 PHY_TYPE_USB3 0>;
> + phy-names = "usb3-phy";
> +};
> +
> +&usb0_phy {
> + maximum-speed = "super-speed";
> + snps,dis-u1-entry-quirk;
> + snps,dis-u2-entry-quirk;
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
> new file mode 100644
> index 000000000000..c62549a4b436
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) Siemens AG, 2018-2021
> + *
> + * Authors:
> + * Le Jin <le.jin@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
> + *
> + * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 2
> + * 1 GB RAM, no eMMC, main_uart0 on connector X30
> + *
> + * Product homepage:
> + * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-am6528-iot2050-basic-common.dtsi"
> +#include "k3-am65-iot2050-common-pg2.dtsi"
> +
> +/ {
> + compatible = "siemens,iot2050-basic-pg2", "ti,am654";
> + model = "SIMATIC IOT2050 Basic PG2";
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
> new file mode 100644
> index 000000000000..f00dc86d01b9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) Siemens AG, 2018-2021
> + *
> + * Authors:
> + * Le Jin <le.jin@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
> + *
> + * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 2
> + * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
> + *
> + * Product homepage:
> + * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-am6548-iot2050-advanced-common.dtsi"
> +#include "k3-am65-iot2050-common-pg2.dtsi"
> +
> +/ {
> + compatible = "siemens,iot2050-advanced-pg2", "ti,am654";
^^ siemens,iot2050-basic-pg2 -> needs a yaml update?
> + model = "SIMATIC IOT2050 Advanced PG2";
> +};
> +
> +&mcu_r5fss0 {
> + /* lock-step mode not supported on this board */
> + ti,cluster-mode = <0>;
> +};
> --
> 2.31.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v3 5/5] arm64: dts: ti: iot2050: Add support for product generation 2 boards
@ 2021-09-14 20:15 ` Nishanth Menon
0 siblings, 0 replies; 24+ messages in thread
From: Nishanth Menon @ 2021-09-14 20:15 UTC (permalink / raw)
To: Jan Kiszka
Cc: Tero Kristo, Rob Herring, linux-arm-kernel, linux-kernel,
devicetree, Bao Cheng Su, Chao Zeng
On 21:41-20210909, Jan Kiszka wrote:
> From: Jan Kiszka <jan.kiszka@siemens.com>
>
> This adds the devices trees for IOT2050 Product Generation 2 (PG2)
> boards. We have Basic and an Advanced variants again, differing in
> number of cores, RAM size, availability of eMMC and further details.
> The major difference to PG1 is the used silicon revision (SR2.x on
> PG2).
>
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
> arch/arm64/boot/dts/ti/Makefile | 2 +
> .../dts/ti/k3-am65-iot2050-common-pg2.dtsi | 51 +++++++++++++++++++
> .../dts/ti/k3-am6528-iot2050-basic-pg2.dts | 24 +++++++++
> .../dts/ti/k3-am6548-iot2050-advanced-pg2.dts | 29 +++++++++++
> 4 files changed, 106 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
> create mode 100644 arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
> create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index d56c742f5a10..41a4bc96e6bd 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -8,7 +8,9 @@
>
> dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
>
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
> new file mode 100644
> index 000000000000..2323628b0444
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
> @@ -0,0 +1,51 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) Siemens AG, 2021
> + *
> + * Authors:
> + * Chao Zeng <chao.zeng@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
> + *
> + * Common bits of the IOT2050 Basic and Advanced variants, PG2
> + */
> +
> +&main_pmx0 {
> + cp2102n_reset_pin_default: cp2102n_reset_pin_default {
cp2102n_reset_pin_default: cp2102n-reset-pin-default
> + pinctrl-single,pins = <
> + /* (AF12) GPIO1_24, used as cp2102 reset */
> + AM65X_IOPAD(0x01e0, PIN_OUTPUT, 7)
> + >;
> + };
> +};
> +
> +&main_gpio1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp2102n_reset_pin_default>;
> + gpio-line-names =
> + "", "", "", "", "", "", "", "", "", "",
> + "", "", "", "", "", "", "", "", "", "",
> + "", "", "", "", "CP2102N-RESET";
> +};
> +
> +&dss {
> + /* Workaround needed to get DP clock of 154Mhz */
> + assigned-clocks = <&k3_clks 67 0>;
> +};
> +
> +&serdes0 {
> + assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
> + assigned-clock-parents = <&k3_clks 153 7>, <&k3_clks 153 4>;
> +};
> +
> +&dwc3_0 {
> + assigned-clock-parents = <&k3_clks 151 4>, /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
> + <&k3_clks 151 8>; /* set PIPE3_TXB_CLK to WIZ8B2M4VSB */
> + phys = <&serdes0 PHY_TYPE_USB3 0>;
> + phy-names = "usb3-phy";
> +};
> +
> +&usb0_phy {
> + maximum-speed = "super-speed";
> + snps,dis-u1-entry-quirk;
> + snps,dis-u2-entry-quirk;
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
> new file mode 100644
> index 000000000000..c62549a4b436
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) Siemens AG, 2018-2021
> + *
> + * Authors:
> + * Le Jin <le.jin@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
> + *
> + * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 2
> + * 1 GB RAM, no eMMC, main_uart0 on connector X30
> + *
> + * Product homepage:
> + * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-am6528-iot2050-basic-common.dtsi"
> +#include "k3-am65-iot2050-common-pg2.dtsi"
> +
> +/ {
> + compatible = "siemens,iot2050-basic-pg2", "ti,am654";
> + model = "SIMATIC IOT2050 Basic PG2";
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
> new file mode 100644
> index 000000000000..f00dc86d01b9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) Siemens AG, 2018-2021
> + *
> + * Authors:
> + * Le Jin <le.jin@siemens.com>
> + * Jan Kiszka <jan.kiszka@siemens.com>
> + *
> + * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 2
> + * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
> + *
> + * Product homepage:
> + * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
> + */
> +
> +/dts-v1/;
> +
> +#include "k3-am6548-iot2050-advanced-common.dtsi"
> +#include "k3-am65-iot2050-common-pg2.dtsi"
> +
> +/ {
> + compatible = "siemens,iot2050-advanced-pg2", "ti,am654";
^^ siemens,iot2050-basic-pg2 -> needs a yaml update?
> + model = "SIMATIC IOT2050 Advanced PG2";
> +};
> +
> +&mcu_r5fss0 {
> + /* lock-step mode not supported on this board */
> + ti,cluster-mode = <0>;
> +};
> --
> 2.31.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread