From mboxrd@z Thu Jan 1 00:00:00 1970 From: Neil Armstrong Subject: Re: [PATCH v3] pinctrl: Add SX150X GPIO Extender Pinctrl Driver Date: Fri, 21 Oct 2016 11:19:08 +0200 Message-ID: References: <1477040998-2016-1-git-send-email-narmstrong@baylibre.com> Mime-Version: 1.0 Content-Type: text/plain; charset=windows-1252 Content-Transfer-Encoding: 7bit Return-path: Received: from mail-qt0-f182.google.com ([209.85.216.182]:34492 "EHLO mail-qt0-f182.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S933480AbcJUJTR (ORCPT ); Fri, 21 Oct 2016 05:19:17 -0400 Received: by mail-qt0-f182.google.com with SMTP id q7so79071601qtq.1 for ; Fri, 21 Oct 2016 02:19:17 -0700 (PDT) In-Reply-To: <1477040998-2016-1-git-send-email-narmstrong@baylibre.com> Sender: linux-gpio-owner@vger.kernel.org List-Id: linux-gpio@vger.kernel.org To: linus.walleij@linaro.org, peda@axentia.se Cc: linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, stigge@antcom.de, vladimir_zapolskiy@mentor.com, andrew.smirnov@gmail.com On 10/21/2016 11:09 AM, Neil Armstrong wrote: > Since the I2C sx150x GPIO expander driver uses platform_data to manage > the pins configurations, rewrite the driver as a pinctrl driver using > pinconf to get/set pin configurations from DT or debugfs. > > The pinctrl driver is functionnally equivalent as the gpio-only driver > and can use DT for pinconf. The platform_data confirmation is dropped. > > This patchset removed the gpio-only driver and selects the Pinctrl driver > config instead. This patchset also migrates the gpio dt-bindings to pinctrl > and add the pinctrl optional properties. > > The driver was tested with a SX1509 device on a BeagleBone black with > interrupt support and on an X86_64 machine over an I2C to USB converter. > > Signed-off-by: Neil Armstrong Forgot to add : Tested-by: Peter Rosin Acked-by: Rob Herring reported on the v2 patch. > --- > This is a fixed version that builds and runs on non-OF platforms and on > arm based OF. The GPIO version is removed and the bindings are also moved > to the pinctrl bindings. > > Changes since v2 at http://lkml.kernel.org/r/1474991325-1754-1-git-send-email-narmstrong@baylibre.com: > - rebased on v4.9-rc1 > - removed MODULE_DEVICE_TABLE as in upstream bb411e771b0e [1] > > Changes since v1 at http://lkml.kernel.org/r/1473166599-29266-1-git-send-email-narmstrong@baylibre.com: > - Fix Kconfig descriptions on pinctrl and gpio > - Fix Kconfig dependency > - Remove oscio support for non-789 devices > - correct typo in dt bindings > - remove probe reset for non-789 devices > > Changes since RFC at http://lkml.kernel.org/r/1472130692-14404-1-git-send-email-narmstrong@baylibre.com: > - Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms > - No more rely on OF_GPIO config > - Moved and enhanced bindings to pinctrl bindings > - Removed gpio-sx150x.c > - Temporary select PINCTRL_SX150X when GPIO_SX150X > - Temporary mark GPIO_SX150X as deprecated > > [1] gpio: sx150x: fix implicit assumption module.h is present > > .../gpio-sx150x.txt => pinctrl/pinctrl-sx150x.txt} | 46 +- > drivers/gpio/Kconfig | 13 +- > drivers/gpio/Makefile | 1 - > drivers/pinctrl/Kconfig | 14 + > drivers/pinctrl/Makefile | 1 + > .../gpio-sx150x.c => pinctrl/pinctrl-sx150x.c} | 1174 ++++++++++++-------- > 6 files changed, 779 insertions(+), 470 deletions(-) > rename Documentation/devicetree/bindings/{gpio/gpio-sx150x.txt => pinctrl/pinctrl-sx150x.txt} (40%) > rename drivers/{gpio/gpio-sx150x.c => pinctrl/pinctrl-sx150x.c} (23%) > > diff --git a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt > similarity index 40% > rename from Documentation/devicetree/bindings/gpio/gpio-sx150x.txt > rename to Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt > index c809acb..c293c8a 100644 > --- a/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt > +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sx150x.txt > @@ -1,34 +1,54 @@ > SEMTECH SX150x GPIO expander bindings > > +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and > +../interrupt-controller/interrupts.txt for generic information regarding > +pin controller, GPIO, and interrupt bindings. > > Required properties: > - > -- compatible: should be "semtech,sx1506q", > +- compatible: should be one of : > + "semtech,sx1506q", > "semtech,sx1508q", > "semtech,sx1509q", > "semtech,sx1502q". > > - reg: The I2C slave address for this device. > > -- interrupt-parent: phandle of the parent interrupt controller. > - > -- interrupts: Interrupt specifier for the controllers interrupt. > - > - #gpio-cells: Should be 2. The first cell is the GPIO number and the > second cell is used to specify optional parameters: > bit 0: polarity (0: normal, 1: inverted) > > - gpio-controller: Marks the device as a GPIO controller. > > +Optional properties : > +- interrupt-parent: phandle of the parent interrupt controller. > + > +- interrupts: Interrupt specifier for the controllers interrupt. > + > - interrupt-controller: Marks the device as a interrupt controller. > > +- semtech,probe-reset: Will trigger a reset of the GPIO expander on probe, > + only for sx1508q and sx1509q > + > The GPIO expander can optionally be used as an interrupt controller, in > -which case it uses the default two cell specifier as described in > -Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. > +which case it uses the default two cell specifier. > + > +Required properties for pin configuration sub-nodes: > + - pins: List of pins to which the configuration applies. > + > +Optional properties for pin configuration sub-nodes: > +---------------------------------------------------- > + - bias-disable: disable any pin bias, except the OSCIO pin > + - bias-pull-up: pull up the pin, except the OSCIO pin > + - bias-pull-down: pull down the pin, except the OSCIO pin > + - bias-pull-pin-default: use pin-default pull state, except the OSCIO pin > + - drive-push-pull: drive actively high and low > + - drive-open-drain: drive with open drain only for sx1508q and sx1509q and except the OSCIO pin > + - output-low: set the pin to output mode with low level > + - output-high: set the pin to output mode with high level > > Example: > > - i2c_gpio_expander@20{ > + i2c0gpio-expander@20{ > #gpio-cells = <2>; > #interrupt-cells = <2>; > compatible = "semtech,sx1506q"; > @@ -38,4 +58,12 @@ Example: > > gpio-controller; > interrupt-controller; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio1_cfg_pins>; > + > + gpio1_cfg_pins: gpio1-cfg { > + pins = "gpio1"; > + bias-pull-up; > + }; > }; > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig > index 26ee00f..db3f7aa 100644 > --- a/drivers/gpio/Kconfig > +++ b/drivers/gpio/Kconfig > @@ -781,16 +781,13 @@ config GPIO_PCF857X > platform-neutral GPIO calls. > > config GPIO_SX150X > - bool "Semtech SX150x I2C GPIO expander" > - depends on I2C=y > - select GPIOLIB_IRQCHIP > + bool "Semtech SX150x I2C GPIO expander (deprecated)" > + depends on PINCTRL && I2C=y > + select PINCTRL_SX150X > default n > help > - Say yes here to provide support for Semtech SX150-series I2C > - GPIO expanders. Compatible models include: > - > - 8 bits: sx1508q > - 16 bits: sx1509q > + Say yes here to provide support for Semtech SX150x-series I2C > + GPIO expanders. The GPIO driver was replaced by a Pinctrl version. > > config GPIO_TPIC2810 > tristate "TPIC2810 8-Bit I2C GPO expander" > diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile > index ab28a2d..76c7af6 100644 > --- a/drivers/gpio/Makefile > +++ b/drivers/gpio/Makefile > @@ -102,7 +102,6 @@ obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o > obj-$(CONFIG_GPIO_STA2X11) += gpio-sta2x11.o > obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o > obj-$(CONFIG_GPIO_STP_XWAY) += gpio-stp-xway.o > -obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o > obj-$(CONFIG_GPIO_SYSCON) += gpio-syscon.o > obj-$(CONFIG_GPIO_TB10X) += gpio-tb10x.o > obj-$(CONFIG_GPIO_TC3589X) += gpio-tc3589x.o > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > index 0e75d94..801fa8b 100644 > --- a/drivers/pinctrl/Kconfig > +++ b/drivers/pinctrl/Kconfig > @@ -164,6 +164,20 @@ config PINCTRL_SIRF > select GENERIC_PINCONF > select GPIOLIB_IRQCHIP > > +config PINCTRL_SX150X > + bool "Semtech SX150x I2C GPIO expander pinctrl driver" > + depends on GPIOLIB && I2C=y > + select PINMUX > + select PINCONF > + select GENERIC_PINCONF > + select GPIOLIB_IRQCHIP > + help > + Say yes here to provide support for Semtech SX150x-series I2C > + GPIO expanders as pinctrl module. > + Compatible models include: > + - 8 bits: sx1508q, sx1502q > + - 16 bits: sx1509q, sx1506q > + > config PINCTRL_PISTACHIO > def_bool y if MACH_PISTACHIO > depends on GPIOLIB > diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile > index 11bad37..3b8e6f7 100644 > --- a/drivers/pinctrl/Makefile > +++ b/drivers/pinctrl/Makefile > @@ -25,6 +25,7 @@ obj-$(CONFIG_PINCTRL_PISTACHIO) += pinctrl-pistachio.o > obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o > obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o > obj-$(CONFIG_PINCTRL_SIRF) += sirf/ > +obj-$(CONFIG_PINCTRL_SX150X) += pinctrl-sx150x.o > obj-$(CONFIG_ARCH_TEGRA) += tegra/ > obj-$(CONFIG_PINCTRL_TZ1090) += pinctrl-tz1090.o > obj-$(CONFIG_PINCTRL_TZ1090_PDC) += pinctrl-tz1090-pdc.o > diff --git a/drivers/gpio/gpio-sx150x.c b/drivers/pinctrl/pinctrl-sx150x.c > similarity index 23% > rename from drivers/gpio/gpio-sx150x.c > rename to drivers/pinctrl/pinctrl-sx150x.c > index af95de8..e985471 100644 > --- a/drivers/gpio/gpio-sx150x.c > +++ b/drivers/pinctrl/pinctrl-sx150x.c > @@ -1,4 +1,8 @@ > -/* Copyright (c) 2010, Code Aurora Forum. All rights reserved. > +/* > + * Copyright (c) 2016, BayLibre, SAS. All rights reserved. > + * Author: Neil Armstrong > + * > + * Copyright (c) 2010, Code Aurora Forum. All rights reserved. > * > * Driver for Semtech SX150X I2C GPIO Expanders > * > @@ -12,13 +16,8 @@ > * but WITHOUT ANY WARRANTY; without even the implied warranty of > * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > * GNU General Public License for more details. > - * > - * You should have received a copy of the GNU General Public License > - * along with this program; if not, write to the Free Software > - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA > - * 02110-1301, USA. > */ > -#include > + > #include > #include > #include > @@ -26,17 +25,23 @@ > #include > #include > #include > -#include > -#include > -#include > -#include > +#include > +#include > +#include > +#include > +#include > +#include > > -#define NO_UPDATE_PENDING -1 > +#include "core.h" > +#include "pinconf.h" > +#include "pinctrl-utils.h" > > /* The chip models of sx150x */ > -#define SX150X_123 0 > -#define SX150X_456 1 > -#define SX150X_789 2 > +enum { > + SX150X_123 = 0, > + SX150X_456, > + SX150X_789, > +}; > > struct sx150x_123_pri { > u8 reg_pld_mode; > @@ -82,167 +87,146 @@ struct sx150x_device_data { > struct sx150x_456_pri x456; > struct sx150x_789_pri x789; > } pri; > + const struct pinctrl_pin_desc *pins; > + unsigned int npins; > }; > > -/** > - * struct sx150x_platform_data - config data for SX150x driver > - * @gpio_base: The index number of the first GPIO assigned to this > - * GPIO expander. The expander will create a block of > - * consecutively numbered gpios beginning at the given base, > - * with the size of the block depending on the model of the > - * expander chip. > - * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO > - * instead of as an oscillator, increasing the size of the > - * GP(I)O pool created by this expander by one. The > - * output-only GPO pin will be added at the end of the block. > - * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor > - * for each IO line in the expander. Setting the bit at > - * position n will enable the pull-up for the IO at > - * the corresponding offset. For chips with fewer than > - * 16 IO pins, high-end bits are ignored. > - * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down > - * resistor for each IO line in the expander. Setting the > - * bit at position n will enable the pull-down for the IO at > - * the corresponding offset. For chips with fewer than > - * 16 IO pins, high-end bits are ignored. > - * @io_polarity: A bit-mask which enables polarity inversion for each IO line > - * in the expander. Setting the bit at position n inverts > - * the polarity of that IO line, while clearing it results > - * in normal polarity. For chips with fewer than 16 IO pins, > - * high-end bits are ignored. > - * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line > - * is connected, via which it reports interrupt events > - * across all GPIO lines. This must be a real, > - * pre-existing IRQ line. > - * Setting this value < 0 disables the irq_chip functionality > - * of the driver. > - * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based > - * IRQ lines will appear. Similarly to gpio_base, the expander > - * will create a block of irqs beginning at this number. > - * This value is ignored if irq_summary is < 0. > - * @reset_during_probe: If set to true, the driver will trigger a full > - * reset of the chip at the beginning of the probe > - * in order to place it in a known state. > - */ > -struct sx150x_platform_data { > - unsigned gpio_base; > - bool oscio_is_gpo; > - u16 io_pullup_ena; > - u16 io_pulldn_ena; > - u16 io_polarity; > - int irq_summary; > - unsigned irq_base; > - bool reset_during_probe; > +struct sx150x_pinctrl { > + struct device *dev; > + struct i2c_client *client; > + struct pinctrl_dev *pctldev; > + struct pinctrl_desc pinctrl_desc; > + struct gpio_chip gpio; > + struct irq_chip irq_chip; > + struct { > + int update; > + u32 sense; > + u32 masked; > + u32 dev_sense; > + u32 dev_masked; > + } irq; > + struct mutex lock; > + const struct sx150x_device_data *data; > }; > > -struct sx150x_chip { > - struct gpio_chip gpio_chip; > - struct i2c_client *client; > - const struct sx150x_device_data *dev_cfg; > - int irq_summary; > - int irq_base; > - int irq_update; > - u32 irq_sense; > - u32 irq_masked; > - u32 dev_sense; > - u32 dev_masked; > - struct irq_chip irq_chip; > - struct mutex lock; > +static const struct pinctrl_pin_desc sx150x_8_pins[] = { > + PINCTRL_PIN(0, "gpio0"), > + PINCTRL_PIN(1, "gpio1"), > + PINCTRL_PIN(2, "gpio2"), > + PINCTRL_PIN(3, "gpio3"), > + PINCTRL_PIN(4, "gpio4"), > + PINCTRL_PIN(5, "gpio5"), > + PINCTRL_PIN(6, "gpio6"), > + PINCTRL_PIN(7, "gpio7"), > + PINCTRL_PIN(8, "oscio"), > }; > > -static const struct sx150x_device_data sx150x_devices[] = { > - [0] = { /* sx1508q */ > - .model = SX150X_789, > - .reg_pullup = 0x03, > - .reg_pulldn = 0x04, > - .reg_dir = 0x07, > - .reg_data = 0x08, > - .reg_irq_mask = 0x09, > - .reg_irq_src = 0x0c, > - .reg_sense = 0x0b, > - .pri.x789 = { > - .reg_drain = 0x05, > - .reg_polarity = 0x06, > - .reg_clock = 0x0f, > - .reg_misc = 0x10, > - .reg_reset = 0x7d, > - }, > - .ngpios = 8, > - }, > - [1] = { /* sx1509q */ > - .model = SX150X_789, > - .reg_pullup = 0x07, > - .reg_pulldn = 0x09, > - .reg_dir = 0x0f, > - .reg_data = 0x11, > - .reg_irq_mask = 0x13, > - .reg_irq_src = 0x19, > - .reg_sense = 0x17, > - .pri.x789 = { > - .reg_drain = 0x0b, > - .reg_polarity = 0x0d, > - .reg_clock = 0x1e, > - .reg_misc = 0x1f, > - .reg_reset = 0x7d, > - }, > - .ngpios = 16 > - }, > - [2] = { /* sx1506q */ > - .model = SX150X_456, > - .reg_pullup = 0x05, > - .reg_pulldn = 0x07, > - .reg_dir = 0x03, > - .reg_data = 0x01, > - .reg_irq_mask = 0x09, > - .reg_irq_src = 0x0f, > - .reg_sense = 0x0d, > - .pri.x456 = { > - .reg_pld_mode = 0x21, > - .reg_pld_table0 = 0x23, > - .reg_pld_table1 = 0x25, > - .reg_pld_table2 = 0x27, > - .reg_pld_table3 = 0x29, > - .reg_pld_table4 = 0x2b, > - .reg_advance = 0xad, > - }, > - .ngpios = 16 > +static const struct pinctrl_pin_desc sx150x_16_pins[] = { > + PINCTRL_PIN(0, "gpio0"), > + PINCTRL_PIN(1, "gpio1"), > + PINCTRL_PIN(2, "gpio2"), > + PINCTRL_PIN(3, "gpio3"), > + PINCTRL_PIN(4, "gpio4"), > + PINCTRL_PIN(5, "gpio5"), > + PINCTRL_PIN(6, "gpio6"), > + PINCTRL_PIN(7, "gpio7"), > + PINCTRL_PIN(8, "gpio8"), > + PINCTRL_PIN(9, "gpio9"), > + PINCTRL_PIN(10, "gpio10"), > + PINCTRL_PIN(11, "gpio11"), > + PINCTRL_PIN(12, "gpio12"), > + PINCTRL_PIN(13, "gpio13"), > + PINCTRL_PIN(14, "gpio14"), > + PINCTRL_PIN(15, "gpio15"), > + PINCTRL_PIN(16, "oscio"), > +}; > + > +static const struct sx150x_device_data sx1508q_device_data = { > + .model = SX150X_789, > + .reg_pullup = 0x03, > + .reg_pulldn = 0x04, > + .reg_dir = 0x07, > + .reg_data = 0x08, > + .reg_irq_mask = 0x09, > + .reg_irq_src = 0x0c, > + .reg_sense = 0x0b, > + .pri.x789 = { > + .reg_drain = 0x05, > + .reg_polarity = 0x06, > + .reg_clock = 0x0f, > + .reg_misc = 0x10, > + .reg_reset = 0x7d, > }, > - [3] = { /* sx1502q */ > - .model = SX150X_123, > - .reg_pullup = 0x02, > - .reg_pulldn = 0x03, > - .reg_dir = 0x01, > - .reg_data = 0x00, > - .reg_irq_mask = 0x05, > - .reg_irq_src = 0x08, > - .reg_sense = 0x07, > - .pri.x123 = { > - .reg_pld_mode = 0x10, > - .reg_pld_table0 = 0x11, > - .reg_pld_table1 = 0x12, > - .reg_pld_table2 = 0x13, > - .reg_pld_table3 = 0x14, > - .reg_pld_table4 = 0x15, > - .reg_advance = 0xad, > - }, > - .ngpios = 8, > + .ngpios = 8, > + .pins = sx150x_8_pins, > + .npins = ARRAY_SIZE(sx150x_8_pins), > +}; > + > +static const struct sx150x_device_data sx1509q_device_data = { > + .model = SX150X_789, > + .reg_pullup = 0x07, > + .reg_pulldn = 0x09, > + .reg_dir = 0x0f, > + .reg_data = 0x11, > + .reg_irq_mask = 0x13, > + .reg_irq_src = 0x19, > + .reg_sense = 0x17, > + .pri.x789 = { > + .reg_drain = 0x0b, > + .reg_polarity = 0x0d, > + .reg_clock = 0x1e, > + .reg_misc = 0x1f, > + .reg_reset = 0x7d, > }, > + .ngpios = 16, > + .pins = sx150x_16_pins, > + .npins = ARRAY_SIZE(sx150x_16_pins), > }; > > -static const struct i2c_device_id sx150x_id[] = { > - {"sx1508q", 0}, > - {"sx1509q", 1}, > - {"sx1506q", 2}, > - {"sx1502q", 3}, > - {} > +static const struct sx150x_device_data sx1506q_device_data = { > + .model = SX150X_456, > + .reg_pullup = 0x05, > + .reg_pulldn = 0x07, > + .reg_dir = 0x03, > + .reg_data = 0x01, > + .reg_irq_mask = 0x09, > + .reg_irq_src = 0x0f, > + .reg_sense = 0x0d, > + .pri.x456 = { > + .reg_pld_mode = 0x21, > + .reg_pld_table0 = 0x23, > + .reg_pld_table1 = 0x25, > + .reg_pld_table2 = 0x27, > + .reg_pld_table3 = 0x29, > + .reg_pld_table4 = 0x2b, > + .reg_advance = 0xad, > + }, > + .ngpios = 16, > + .pins = sx150x_16_pins, > + .npins = 16, /* oscio not available */ > }; > > -static const struct of_device_id sx150x_of_match[] = { > - { .compatible = "semtech,sx1508q" }, > - { .compatible = "semtech,sx1509q" }, > - { .compatible = "semtech,sx1506q" }, > - { .compatible = "semtech,sx1502q" }, > - {}, > +static const struct sx150x_device_data sx1502q_device_data = { > + .model = SX150X_123, > + .reg_pullup = 0x02, > + .reg_pulldn = 0x03, > + .reg_dir = 0x01, > + .reg_data = 0x00, > + .reg_irq_mask = 0x05, > + .reg_irq_src = 0x08, > + .reg_sense = 0x07, > + .pri.x123 = { > + .reg_pld_mode = 0x10, > + .reg_pld_table0 = 0x11, > + .reg_pld_table1 = 0x12, > + .reg_pld_table2 = 0x13, > + .reg_pld_table3 = 0x14, > + .reg_pld_table4 = 0x15, > + .reg_advance = 0xad, > + }, > + .ngpios = 8, > + .pins = sx150x_8_pins, > + .npins = 8, /* oscio not available */ > }; > > static s32 sx150x_i2c_write(struct i2c_client *client, u8 reg, u8 val) > @@ -269,11 +253,6 @@ static s32 sx150x_i2c_read(struct i2c_client *client, u8 reg, u8 *val) > return err; > } > > -static inline bool offset_is_oscio(struct sx150x_chip *chip, unsigned offset) > -{ > - return (chip->dev_cfg->ngpios == offset); > -} > - > /* > * These utility functions solve the common problem of locating and setting > * configuration bits. Configuration bits are grouped into registers > @@ -294,7 +273,7 @@ static inline bool offset_is_oscio(struct sx150x_chip *chip, unsigned offset) > * register and mask the correct bits. > */ > static inline void sx150x_find_cfg(u8 offset, u8 width, > - u8 *reg, u8 *mask, u8 *shift) > + u8 *reg, u8 *mask, u8 *shift) > { > *reg -= offset * width / 8; > *mask = (1 << width) - 1; > @@ -302,185 +281,241 @@ static inline void sx150x_find_cfg(u8 offset, u8 width, > *mask <<= *shift; > } > > -static s32 sx150x_write_cfg(struct sx150x_chip *chip, > - u8 offset, u8 width, u8 reg, u8 val) > +static int sx150x_write_cfg(struct i2c_client *client, > + u8 offset, u8 width, u8 reg, u8 val) > { > u8 mask; > u8 data; > u8 shift; > - s32 err; > + int err; > > sx150x_find_cfg(offset, width, ®, &mask, &shift); > - err = sx150x_i2c_read(chip->client, reg, &data); > + err = sx150x_i2c_read(client, reg, &data); > if (err < 0) > return err; > > data &= ~mask; > data |= (val << shift) & mask; > - return sx150x_i2c_write(chip->client, reg, data); > + return sx150x_i2c_write(client, reg, data); > } > > -static int sx150x_get_io(struct sx150x_chip *chip, unsigned offset) > +static int sx150x_read_cfg(struct i2c_client *client, > + u8 offset, u8 width, u8 reg) > { > - u8 reg = chip->dev_cfg->reg_data; > u8 mask; > u8 data; > u8 shift; > - s32 err; > + int err; > > - sx150x_find_cfg(offset, 1, ®, &mask, &shift); > - err = sx150x_i2c_read(chip->client, reg, &data); > - if (err >= 0) > - err = (data & mask) != 0 ? 1 : 0; > + sx150x_find_cfg(offset, width, ®, &mask, &shift); > + err = sx150x_i2c_read(client, reg, &data); > + if (err < 0) > + return err; > > - return err; > + return (data & mask); > } > > -static void sx150x_set_oscio(struct sx150x_chip *chip, int val) > +static int sx150x_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) > { > - sx150x_i2c_write(chip->client, > - chip->dev_cfg->pri.x789.reg_clock, > - (val ? 0x1f : 0x10)); > + return 0; > } > > -static void sx150x_set_io(struct sx150x_chip *chip, unsigned offset, int val) > +static const char *sx150x_pinctrl_get_group_name(struct pinctrl_dev *pctldev, > + unsigned int group) > { > - sx150x_write_cfg(chip, > - offset, > - 1, > - chip->dev_cfg->reg_data, > - (val ? 1 : 0)); > + return NULL; > } > > -static int sx150x_io_input(struct sx150x_chip *chip, unsigned offset) > +static int sx150x_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, > + unsigned int group, > + const unsigned int **pins, > + unsigned int *num_pins) > { > - return sx150x_write_cfg(chip, > - offset, > - 1, > - chip->dev_cfg->reg_dir, > - 1); > + return -ENOTSUPP; > } > > -static int sx150x_io_output(struct sx150x_chip *chip, unsigned offset, int val) > +static const struct pinctrl_ops sx150x_pinctrl_ops = { > + .get_groups_count = sx150x_pinctrl_get_groups_count, > + .get_group_name = sx150x_pinctrl_get_group_name, > + .get_group_pins = sx150x_pinctrl_get_group_pins, > +#ifdef CONFIG_OF > + .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, > + .dt_free_map = pinctrl_utils_free_map, > +#endif > +}; > + > +static bool sx150x_pin_is_oscio(struct sx150x_pinctrl *pctl, unsigned int pin) > { > - int err; > + if (pin >= pctl->data->npins) > + return false; > > - err = sx150x_write_cfg(chip, > - offset, > - 1, > - chip->dev_cfg->reg_data, > - (val ? 1 : 0)); > - if (err >= 0) > - err = sx150x_write_cfg(chip, > - offset, > - 1, > - chip->dev_cfg->reg_dir, > - 0); > - return err; > + /* OSCIO pin is only present in 789 devices */ > + if (pctl->data->model != SX150X_789) > + return false; > + > + return !strcmp(pctl->data->pins[pin].name, "oscio"); > } > > -static int sx150x_gpio_get(struct gpio_chip *gc, unsigned offset) > +static int sx150x_gpio_get_direction(struct gpio_chip *chip, > + unsigned int offset) > { > - struct sx150x_chip *chip = gpiochip_get_data(gc); > - int status = -EINVAL; > + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); > + int status; > > - if (!offset_is_oscio(chip, offset)) { > - mutex_lock(&chip->lock); > - status = sx150x_get_io(chip, offset); > - mutex_unlock(&chip->lock); > - } > + if (sx150x_pin_is_oscio(pctl, offset)) > + return false; > + > + status = sx150x_read_cfg(pctl->client, offset, 1, pctl->data->reg_dir); > + if (status >= 0) > + status = !!status; > > - return (status < 0) ? status : !!status; > + return status; > } > > -static void sx150x_gpio_set(struct gpio_chip *gc, unsigned offset, int val) > +static int sx150x_gpio_get(struct gpio_chip *chip, unsigned int offset) > { > - struct sx150x_chip *chip = gpiochip_get_data(gc); > + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); > + int status; > > - mutex_lock(&chip->lock); > - if (offset_is_oscio(chip, offset)) > - sx150x_set_oscio(chip, val); > - else > - sx150x_set_io(chip, offset, val); > - mutex_unlock(&chip->lock); > + if (sx150x_pin_is_oscio(pctl, offset)) > + return -EINVAL; > + > + status = sx150x_read_cfg(pctl->client, offset, 1, pctl->data->reg_data); > + if (status >= 0) > + status = !!status; > + > + return status; > } > > -static int sx150x_gpio_set_single_ended(struct gpio_chip *gc, > - unsigned offset, > - enum single_ended_mode mode) > +static int sx150x_gpio_set_single_ended(struct gpio_chip *chip, > + unsigned int offset, > + enum single_ended_mode mode) > { > - struct sx150x_chip *chip = gpiochip_get_data(gc); > - > - /* On the SX160X 789 we can set open drain */ > - if (chip->dev_cfg->model != SX150X_789) > + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); > + int ret; > + > + switch (mode) { > + case LINE_MODE_PUSH_PULL: > + if (pctl->data->model != SX150X_789 || > + sx150x_pin_is_oscio(pctl, offset)) > + return 0; > + > + mutex_lock(&pctl->lock); > + ret = sx150x_write_cfg(pctl->client, offset, 1, > + pctl->data->pri.x789.reg_drain, > + 0); > + mutex_unlock(&pctl->lock); > + if (ret < 0) > + return ret; > + break; > + > + case LINE_MODE_OPEN_DRAIN: > + if (pctl->data->model != SX150X_789 || > + sx150x_pin_is_oscio(pctl, offset)) > + return -ENOTSUPP; > + > + mutex_lock(&pctl->lock); > + ret = sx150x_write_cfg(pctl->client, offset, 1, > + pctl->data->pri.x789.reg_drain, > + 1); > + mutex_unlock(&pctl->lock); > + if (ret < 0) > + return ret; > + break; > + > + default: > return -ENOTSUPP; > + } > > - if (mode == LINE_MODE_PUSH_PULL) > - return sx150x_write_cfg(chip, > - offset, > - 1, > - chip->dev_cfg->pri.x789.reg_drain, > - 0); > - > - if (mode == LINE_MODE_OPEN_DRAIN) > - return sx150x_write_cfg(chip, > - offset, > - 1, > - chip->dev_cfg->pri.x789.reg_drain, > - 1); > - return -ENOTSUPP; > + return 0; > } > > -static int sx150x_gpio_direction_input(struct gpio_chip *gc, unsigned offset) > +static void sx150x_gpio_set(struct gpio_chip *chip, unsigned int offset, > + int value) > { > - struct sx150x_chip *chip = gpiochip_get_data(gc); > - int status = -EINVAL; > + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); > + > + if (sx150x_pin_is_oscio(pctl, offset)) { > > - if (!offset_is_oscio(chip, offset)) { > - mutex_lock(&chip->lock); > - status = sx150x_io_input(chip, offset); > - mutex_unlock(&chip->lock); > + mutex_lock(&pctl->lock); > + sx150x_i2c_write(pctl->client, > + pctl->data->pri.x789.reg_clock, > + (value ? 0x1f : 0x10)); > + mutex_unlock(&pctl->lock); > + } else { > + mutex_lock(&pctl->lock); > + sx150x_write_cfg(pctl->client, offset, 1, > + pctl->data->reg_data, > + (value ? 1 : 0)); > + mutex_unlock(&pctl->lock); > } > - return status; > } > > -static int sx150x_gpio_direction_output(struct gpio_chip *gc, > - unsigned offset, > - int val) > +static int sx150x_gpio_direction_input(struct gpio_chip *chip, > + unsigned int offset) > { > - struct sx150x_chip *chip = gpiochip_get_data(gc); > - int status = 0; > + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); > + int ret; > > - if (!offset_is_oscio(chip, offset)) { > - mutex_lock(&chip->lock); > - status = sx150x_io_output(chip, offset, val); > - mutex_unlock(&chip->lock); > + if (sx150x_pin_is_oscio(pctl, offset)) > + return -EINVAL; > + > + mutex_lock(&pctl->lock); > + ret = sx150x_write_cfg(pctl->client, offset, 1, > + pctl->data->reg_dir, 1); > + mutex_unlock(&pctl->lock); > + > + return ret; > +} > + > +static int sx150x_gpio_direction_output(struct gpio_chip *chip, > + unsigned int offset, int value) > +{ > + struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); > + int status; > + > + if (sx150x_pin_is_oscio(pctl, offset)) { > + sx150x_gpio_set(chip, offset, value); > + return 0; > } > + > + mutex_lock(&pctl->lock); > + status = sx150x_write_cfg(pctl->client, offset, 1, > + pctl->data->reg_data, > + (value ? 1 : 0)); > + if (status >= 0) > + status = sx150x_write_cfg(pctl->client, offset, 1, > + pctl->data->reg_dir, 0); > + mutex_unlock(&pctl->lock); > + > return status; > } > > static void sx150x_irq_mask(struct irq_data *d) > { > - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d)); > - unsigned n = d->hwirq; > + struct sx150x_pinctrl *pctl = > + gpiochip_get_data(irq_data_get_irq_chip_data(d)); > + unsigned int n = d->hwirq; > > - chip->irq_masked |= (1 << n); > - chip->irq_update = n; > + pctl->irq.masked |= (1 << n); > + pctl->irq.update = n; > } > > static void sx150x_irq_unmask(struct irq_data *d) > { > - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d)); > - unsigned n = d->hwirq; > + struct sx150x_pinctrl *pctl = > + gpiochip_get_data(irq_data_get_irq_chip_data(d)); > + unsigned int n = d->hwirq; > > - chip->irq_masked &= ~(1 << n); > - chip->irq_update = n; > + pctl->irq.masked &= ~(1 << n); > + pctl->irq.update = n; > } > > static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type) > { > - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d)); > - unsigned n, val = 0; > + struct sx150x_pinctrl *pctl = > + gpiochip_get_data(irq_data_get_irq_chip_data(d)); > + unsigned int n, val = 0; > > if (flow_type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) > return -EINVAL; > @@ -492,37 +527,40 @@ static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type) > if (flow_type & IRQ_TYPE_EDGE_FALLING) > val |= 0x2; > > - chip->irq_sense &= ~(3UL << (n * 2)); > - chip->irq_sense |= val << (n * 2); > - chip->irq_update = n; > + pctl->irq.sense &= ~(3UL << (n * 2)); > + pctl->irq.sense |= val << (n * 2); > + pctl->irq.update = n; > return 0; > } > > static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id) > { > - struct sx150x_chip *chip = (struct sx150x_chip *)dev_id; > - unsigned nhandled = 0; > - unsigned sub_irq; > - unsigned n; > + struct sx150x_pinctrl *pctl = (struct sx150x_pinctrl *)dev_id; > + unsigned int nhandled = 0; > + unsigned int sub_irq; > + unsigned int n; > s32 err; > u8 val; > int i; > > - for (i = (chip->dev_cfg->ngpios / 8) - 1; i >= 0; --i) { > - err = sx150x_i2c_read(chip->client, > - chip->dev_cfg->reg_irq_src - i, > + for (i = (pctl->data->ngpios / 8) - 1; i >= 0; --i) { > + err = sx150x_i2c_read(pctl->client, > + pctl->data->reg_irq_src - i, > &val); > if (err < 0) > continue; > > - sx150x_i2c_write(chip->client, > - chip->dev_cfg->reg_irq_src - i, > - val); > + err = sx150x_i2c_write(pctl->client, > + pctl->data->reg_irq_src - i, > + val); > + if (err < 0) > + continue; > + > for (n = 0; n < 8; ++n) { > if (val & (1 << n)) { > sub_irq = irq_find_mapping( > - chip->gpio_chip.irqdomain, > - (i * 8) + n); > + pctl->gpio.irqdomain, > + (i * 8) + n); > handle_nested_irq(sub_irq); > ++nhandled; > } > @@ -534,251 +572,483 @@ static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id) > > static void sx150x_irq_bus_lock(struct irq_data *d) > { > - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d)); > + struct sx150x_pinctrl *pctl = > + gpiochip_get_data(irq_data_get_irq_chip_data(d)); > > - mutex_lock(&chip->lock); > + mutex_lock(&pctl->lock); > } > > static void sx150x_irq_bus_sync_unlock(struct irq_data *d) > { > - struct sx150x_chip *chip = gpiochip_get_data(irq_data_get_irq_chip_data(d)); > - unsigned n; > + struct sx150x_pinctrl *pctl = > + gpiochip_get_data(irq_data_get_irq_chip_data(d)); > + unsigned int n; > > - if (chip->irq_update == NO_UPDATE_PENDING) > + if (pctl->irq.update < 0) > goto out; > > - n = chip->irq_update; > - chip->irq_update = NO_UPDATE_PENDING; > + n = pctl->irq.update; > + pctl->irq.update = -1; > > /* Avoid updates if nothing changed */ > - if (chip->dev_sense == chip->irq_sense && > - chip->dev_masked == chip->irq_masked) > + if (pctl->irq.dev_sense == pctl->irq.sense && > + pctl->irq.dev_masked == pctl->irq.masked) > goto out; > > - chip->dev_sense = chip->irq_sense; > - chip->dev_masked = chip->irq_masked; > + pctl->irq.dev_sense = pctl->irq.sense; > + pctl->irq.dev_masked = pctl->irq.masked; > > - if (chip->irq_masked & (1 << n)) { > - sx150x_write_cfg(chip, n, 1, chip->dev_cfg->reg_irq_mask, 1); > - sx150x_write_cfg(chip, n, 2, chip->dev_cfg->reg_sense, 0); > + if (pctl->irq.masked & (1 << n)) { > + sx150x_write_cfg(pctl->client, n, 1, > + pctl->data->reg_irq_mask, 1); > + sx150x_write_cfg(pctl->client, n, 2, > + pctl->data->reg_sense, 0); > } else { > - sx150x_write_cfg(chip, n, 1, chip->dev_cfg->reg_irq_mask, 0); > - sx150x_write_cfg(chip, n, 2, chip->dev_cfg->reg_sense, > - chip->irq_sense >> (n * 2)); > + sx150x_write_cfg(pctl->client, n, 1, > + pctl->data->reg_irq_mask, 0); > + sx150x_write_cfg(pctl->client, n, 2, > + pctl->data->reg_sense, > + pctl->irq.sense >> (n * 2)); > } > out: > - mutex_unlock(&chip->lock); > + mutex_unlock(&pctl->lock); > } > > -static void sx150x_init_chip(struct sx150x_chip *chip, > - struct i2c_client *client, > - kernel_ulong_t driver_data, > - struct sx150x_platform_data *pdata) > +static int sx150x_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, > + unsigned long *config) > { > - mutex_init(&chip->lock); > - > - chip->client = client; > - chip->dev_cfg = &sx150x_devices[driver_data]; > - chip->gpio_chip.parent = &client->dev; > - chip->gpio_chip.label = client->name; > - chip->gpio_chip.direction_input = sx150x_gpio_direction_input; > - chip->gpio_chip.direction_output = sx150x_gpio_direction_output; > - chip->gpio_chip.get = sx150x_gpio_get; > - chip->gpio_chip.set = sx150x_gpio_set; > - chip->gpio_chip.set_single_ended = sx150x_gpio_set_single_ended; > - chip->gpio_chip.base = pdata->gpio_base; > - chip->gpio_chip.can_sleep = true; > - chip->gpio_chip.ngpio = chip->dev_cfg->ngpios; > -#ifdef CONFIG_OF_GPIO > - chip->gpio_chip.of_node = client->dev.of_node; > - chip->gpio_chip.of_gpio_n_cells = 2; > -#endif > - if (pdata->oscio_is_gpo) > - ++chip->gpio_chip.ngpio; > - > - chip->irq_chip.name = client->name; > - chip->irq_chip.irq_mask = sx150x_irq_mask; > - chip->irq_chip.irq_unmask = sx150x_irq_unmask; > - chip->irq_chip.irq_set_type = sx150x_irq_set_type; > - chip->irq_chip.irq_bus_lock = sx150x_irq_bus_lock; > - chip->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock; > - chip->irq_summary = -1; > - chip->irq_base = -1; > - chip->irq_masked = ~0; > - chip->irq_sense = 0; > - chip->dev_masked = ~0; > - chip->dev_sense = 0; > - chip->irq_update = NO_UPDATE_PENDING; > + struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); > + unsigned int param = pinconf_to_config_param(*config); > + int ret; > + u32 arg; > + > + if (sx150x_pin_is_oscio(pctl, pin)) { > + u8 data; > + > + switch (param) { > + case PIN_CONFIG_DRIVE_PUSH_PULL: > + case PIN_CONFIG_OUTPUT: > + mutex_lock(&pctl->lock); > + ret = sx150x_i2c_read(pctl->client, > + pctl->data->pri.x789.reg_clock, > + &data); > + mutex_unlock(&pctl->lock); > + > + if (ret < 0) > + return ret; > + > + if (param == PIN_CONFIG_DRIVE_PUSH_PULL) > + arg = (data & 0x1f) ? 1 : 0; > + else { > + if ((data & 0x1f) == 0x1f) > + arg = 1; > + else if ((data & 0x1f) == 0x10) > + arg = 0; > + else > + return -EINVAL; > + } > + > + break; > + default: > + return -ENOTSUPP; > + } > + > + goto out; > + } > + > + switch (param) { > + case PIN_CONFIG_BIAS_PULL_DOWN: > + mutex_lock(&pctl->lock); > + ret = sx150x_read_cfg(pctl->client, pin, 1, > + pctl->data->reg_pulldn); > + mutex_unlock(&pctl->lock); > + > + if (ret < 0) > + return ret; > + > + if (!ret) > + return -EINVAL; > + > + arg = 1; > + break; > + > + case PIN_CONFIG_BIAS_PULL_UP: > + mutex_lock(&pctl->lock); > + ret = sx150x_read_cfg(pctl->client, pin, 1, > + pctl->data->reg_pullup); > + mutex_unlock(&pctl->lock); > + > + if (ret < 0) > + return ret; > + > + if (!ret) > + return -EINVAL; > + > + arg = 1; > + break; > + > + case PIN_CONFIG_DRIVE_OPEN_DRAIN: > + if (pctl->data->model != SX150X_789) > + return -ENOTSUPP; > + > + mutex_lock(&pctl->lock); > + ret = sx150x_read_cfg(pctl->client, pin, 1, > + pctl->data->pri.x789.reg_drain); > + mutex_unlock(&pctl->lock); > + > + if (ret < 0) > + return ret; > + > + if (!ret) > + return -EINVAL; > + > + arg = 1; > + break; > + > + case PIN_CONFIG_DRIVE_PUSH_PULL: > + if (pctl->data->model != SX150X_789) > + arg = true; > + else { > + mutex_lock(&pctl->lock); > + ret = sx150x_read_cfg(pctl->client, pin, 1, > + pctl->data->pri.x789.reg_drain); > + mutex_unlock(&pctl->lock); > + > + if (ret < 0) > + return ret; > + > + if (ret) > + return -EINVAL; > + > + arg = 1; > + } > + break; > + > + case PIN_CONFIG_OUTPUT: > + ret = sx150x_gpio_get_direction(&pctl->gpio, pin); > + if (ret < 0) > + return ret; > + > + if (ret) > + return -EINVAL; > + > + ret = sx150x_gpio_get(&pctl->gpio, pin); > + if (ret < 0) > + return ret; > + > + arg = ret; > + break; > + > + default: > + return -ENOTSUPP; > + } > + > +out: > + *config = pinconf_to_config_packed(param, arg); > + > + return 0; > +} > + > +static int sx150x_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, > + unsigned long *configs, unsigned int num_configs) > +{ > + struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); > + enum pin_config_param param; > + u32 arg; > + int i; > + int ret; > + > + for (i = 0; i < num_configs; i++) { > + param = pinconf_to_config_param(configs[i]); > + arg = pinconf_to_config_argument(configs[i]); > + > + if (sx150x_pin_is_oscio(pctl, pin)) { > + if (param == PIN_CONFIG_OUTPUT) { > + ret = sx150x_gpio_direction_output(&pctl->gpio, > + pin, arg); > + if (ret < 0) > + return ret; > + > + continue; > + } else > + return -ENOTSUPP; > + } > + > + switch (param) { > + case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: > + case PIN_CONFIG_BIAS_DISABLE: > + mutex_lock(&pctl->lock); > + ret = sx150x_write_cfg(pctl->client, pin, 1, > + pctl->data->reg_pulldn, 0); > + mutex_unlock(&pctl->lock); > + if (ret < 0) > + return ret; > + > + mutex_lock(&pctl->lock); > + ret = sx150x_write_cfg(pctl->client, pin, 1, > + pctl->data->reg_pullup, 0); > + mutex_unlock(&pctl->lock); > + if (ret < 0) > + return ret; > + > + break; > + > + case PIN_CONFIG_BIAS_PULL_UP: > + mutex_lock(&pctl->lock); > + ret = sx150x_write_cfg(pctl->client, pin, 1, > + pctl->data->reg_pullup, > + 1); > + mutex_unlock(&pctl->lock); > + if (ret < 0) > + return ret; > + > + break; > + > + case PIN_CONFIG_BIAS_PULL_DOWN: > + mutex_lock(&pctl->lock); > + ret = sx150x_write_cfg(pctl->client, pin, 1, > + pctl->data->reg_pulldn, > + 1); > + mutex_unlock(&pctl->lock); > + if (ret < 0) > + return ret; > + > + break; > + > + case PIN_CONFIG_DRIVE_OPEN_DRAIN: > + ret = sx150x_gpio_set_single_ended(&pctl->gpio, > + pin, LINE_MODE_OPEN_DRAIN); > + if (ret < 0) > + return ret; > + > + break; > + > + case PIN_CONFIG_DRIVE_PUSH_PULL: > + ret = sx150x_gpio_set_single_ended(&pctl->gpio, > + pin, LINE_MODE_PUSH_PULL); > + if (ret < 0) > + return ret; > + > + break; > + > + case PIN_CONFIG_OUTPUT: > + ret = sx150x_gpio_direction_output(&pctl->gpio, > + pin, arg); > + if (ret < 0) > + return ret; > + > + break; > + > + default: > + return -ENOTSUPP; > + } > + } /* for each config */ > + > + return 0; > } > > -static int sx150x_init_io(struct sx150x_chip *chip, u8 base, u16 cfg) > +static const struct pinconf_ops sx150x_pinconf_ops = { > + .pin_config_get = sx150x_pinconf_get, > + .pin_config_set = sx150x_pinconf_set, > + .is_generic = true, > +}; > + > +static const struct i2c_device_id sx150x_id[] = { > + {"sx1508q", (kernel_ulong_t) &sx1508q_device_data }, > + {"sx1509q", (kernel_ulong_t) &sx1509q_device_data }, > + {"sx1506q", (kernel_ulong_t) &sx1506q_device_data }, > + {"sx1502q", (kernel_ulong_t) &sx1502q_device_data }, > + {} > +}; > + > +static const struct of_device_id sx150x_of_match[] = { > + { .compatible = "semtech,sx1508q" }, > + { .compatible = "semtech,sx1509q" }, > + { .compatible = "semtech,sx1506q" }, > + { .compatible = "semtech,sx1502q" }, > + {}, > +}; > + > +static int sx150x_init_io(struct sx150x_pinctrl *pctl, u8 base, u16 cfg) > { > int err = 0; > - unsigned n; > + unsigned int n; > > - for (n = 0; err >= 0 && n < (chip->dev_cfg->ngpios / 8); ++n) > - err = sx150x_i2c_write(chip->client, base - n, cfg >> (n * 8)); > + for (n = 0; err >= 0 && n < (pctl->data->ngpios / 8); ++n) > + err = sx150x_i2c_write(pctl->client, base - n, cfg >> (n * 8)); > return err; > } > > -static int sx150x_reset(struct sx150x_chip *chip) > +static int sx150x_reset(struct sx150x_pinctrl *pctl) > { > int err; > > - err = i2c_smbus_write_byte_data(chip->client, > - chip->dev_cfg->pri.x789.reg_reset, > + err = i2c_smbus_write_byte_data(pctl->client, > + pctl->data->pri.x789.reg_reset, > 0x12); > if (err < 0) > return err; > > - err = i2c_smbus_write_byte_data(chip->client, > - chip->dev_cfg->pri.x789.reg_reset, > + err = i2c_smbus_write_byte_data(pctl->client, > + pctl->data->pri.x789.reg_reset, > 0x34); > return err; > } > > -static int sx150x_init_hw(struct sx150x_chip *chip, > - struct sx150x_platform_data *pdata) > +static int sx150x_init_hw(struct sx150x_pinctrl *pctl) > { > - int err = 0; > + int err; > > - if (pdata->reset_during_probe) { > - err = sx150x_reset(chip); > + if (pctl->data->model == SX150X_789 && > + of_property_read_bool(pctl->dev->of_node, "semtech,probe-reset")) { > + err = sx150x_reset(pctl); > if (err < 0) > return err; > } > > - if (chip->dev_cfg->model == SX150X_789) > - err = sx150x_i2c_write(chip->client, > - chip->dev_cfg->pri.x789.reg_misc, > + if (pctl->data->model == SX150X_789) > + err = sx150x_i2c_write(pctl->client, > + pctl->data->pri.x789.reg_misc, > 0x01); > - else if (chip->dev_cfg->model == SX150X_456) > - err = sx150x_i2c_write(chip->client, > - chip->dev_cfg->pri.x456.reg_advance, > + else if (pctl->data->model == SX150X_456) > + err = sx150x_i2c_write(pctl->client, > + pctl->data->pri.x456.reg_advance, > 0x04); > else > - err = sx150x_i2c_write(chip->client, > - chip->dev_cfg->pri.x123.reg_advance, > + err = sx150x_i2c_write(pctl->client, > + pctl->data->pri.x123.reg_advance, > 0x00); > if (err < 0) > return err; > > - err = sx150x_init_io(chip, chip->dev_cfg->reg_pullup, > - pdata->io_pullup_ena); > - if (err < 0) > - return err; > - > - err = sx150x_init_io(chip, chip->dev_cfg->reg_pulldn, > - pdata->io_pulldn_ena); > - if (err < 0) > - return err; > - > - if (chip->dev_cfg->model == SX150X_789) { > - err = sx150x_init_io(chip, > - chip->dev_cfg->pri.x789.reg_polarity, > - pdata->io_polarity); > + /* Set all pins to work in normal mode */ > + if (pctl->data->model == SX150X_789) { > + err = sx150x_init_io(pctl, > + pctl->data->pri.x789.reg_polarity, > + 0); > if (err < 0) > return err; > - } else if (chip->dev_cfg->model == SX150X_456) { > + } else if (pctl->data->model == SX150X_456) { > /* Set all pins to work in normal mode */ > - err = sx150x_init_io(chip, > - chip->dev_cfg->pri.x456.reg_pld_mode, > + err = sx150x_init_io(pctl, > + pctl->data->pri.x456.reg_pld_mode, > 0); > if (err < 0) > return err; > } else { > /* Set all pins to work in normal mode */ > - err = sx150x_init_io(chip, > - chip->dev_cfg->pri.x123.reg_pld_mode, > + err = sx150x_init_io(pctl, > + pctl->data->pri.x123.reg_pld_mode, > 0); > if (err < 0) > return err; > } > > - > - if (pdata->oscio_is_gpo) > - sx150x_set_oscio(chip, 0); > - > - return err; > -} > - > -static int sx150x_install_irq_chip(struct sx150x_chip *chip, > - int irq_summary, > - int irq_base) > -{ > - int err; > - > - chip->irq_summary = irq_summary; > - chip->irq_base = irq_base; > - > - /* Add gpio chip to irq subsystem */ > - err = gpiochip_irqchip_add(&chip->gpio_chip, > - &chip->irq_chip, chip->irq_base, > - handle_edge_irq, IRQ_TYPE_EDGE_BOTH); > - if (err) { > - dev_err(&chip->client->dev, > - "could not connect irqchip to gpiochip\n"); > - return err; > - } > - > - err = devm_request_threaded_irq(&chip->client->dev, > - irq_summary, NULL, sx150x_irq_thread_fn, > - IRQF_ONESHOT | IRQF_SHARED | IRQF_TRIGGER_FALLING, > - chip->irq_chip.name, chip); > - if (err < 0) { > - chip->irq_summary = -1; > - chip->irq_base = -1; > - } > - > - return err; > + return 0; > } > > static int sx150x_probe(struct i2c_client *client, > - const struct i2c_device_id *id) > + const struct i2c_device_id *id) > { > static const u32 i2c_funcs = I2C_FUNC_SMBUS_BYTE_DATA | > I2C_FUNC_SMBUS_WRITE_WORD_DATA; > - struct sx150x_platform_data *pdata; > - struct sx150x_chip *chip; > - int rc; > + struct device *dev = &client->dev; > + struct sx150x_pinctrl *pctl; > + int ret; > > - pdata = dev_get_platdata(&client->dev); > - if (!pdata) > + if (!id->driver_data) > return -EINVAL; > > if (!i2c_check_functionality(client->adapter, i2c_funcs)) > return -ENOSYS; > > - chip = devm_kzalloc(&client->dev, > - sizeof(struct sx150x_chip), GFP_KERNEL); > - if (!chip) > + pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL); > + if (!pctl) > return -ENOMEM; > > - sx150x_init_chip(chip, client, id->driver_data, pdata); > - rc = sx150x_init_hw(chip, pdata); > - if (rc < 0) > - return rc; > - > - rc = devm_gpiochip_add_data(&client->dev, &chip->gpio_chip, chip); > - if (rc) > - return rc; > - > - if (pdata->irq_summary >= 0) { > - rc = sx150x_install_irq_chip(chip, > - pdata->irq_summary, > - pdata->irq_base); > - if (rc < 0) > - return rc; > + pctl->dev = dev; > + pctl->client = client; > + pctl->data = (void *)id->driver_data; > + > + mutex_init(&pctl->lock); > + > + ret = sx150x_init_hw(pctl); > + if (ret) > + return ret; > + > + /* Register GPIO controller */ > + pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL); > + pctl->gpio.base = -1; > + pctl->gpio.ngpio = pctl->data->npins; > + pctl->gpio.get_direction = sx150x_gpio_get_direction; > + pctl->gpio.direction_input = sx150x_gpio_direction_input; > + pctl->gpio.direction_output = sx150x_gpio_direction_output; > + pctl->gpio.get = sx150x_gpio_get; > + pctl->gpio.set = sx150x_gpio_set; > + pctl->gpio.set_single_ended = sx150x_gpio_set_single_ended; > + pctl->gpio.parent = dev; > +#ifdef CONFIG_OF_GPIO > + pctl->gpio.of_node = dev->of_node; > +#endif > + pctl->gpio.can_sleep = true; > + > + ret = devm_gpiochip_add_data(dev, &pctl->gpio, pctl); > + if (ret) > + return ret; > + > + /* Add Interrupt support if an irq is specified */ > + if (client->irq > 0) { > + pctl->irq_chip.name = devm_kstrdup(dev, client->name, > + GFP_KERNEL); > + pctl->irq_chip.irq_mask = sx150x_irq_mask; > + pctl->irq_chip.irq_unmask = sx150x_irq_unmask; > + pctl->irq_chip.irq_set_type = sx150x_irq_set_type; > + pctl->irq_chip.irq_bus_lock = sx150x_irq_bus_lock; > + pctl->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock; > + > + pctl->irq.masked = ~0; > + pctl->irq.sense = 0; > + pctl->irq.dev_masked = ~0; > + pctl->irq.dev_sense = 0; > + pctl->irq.update = -1; > + > + ret = gpiochip_irqchip_add(&pctl->gpio, > + &pctl->irq_chip, 0, > + handle_edge_irq, IRQ_TYPE_EDGE_BOTH); > + if (ret) { > + dev_err(dev, "could not connect irqchip to gpiochip\n"); > + return ret; > + } > + > + ret = devm_request_threaded_irq(dev, client->irq, NULL, > + sx150x_irq_thread_fn, > + IRQF_ONESHOT | IRQF_SHARED | > + IRQF_TRIGGER_FALLING, > + pctl->irq_chip.name, pctl); > + if (ret < 0) > + return ret; > } > > - i2c_set_clientdata(client, chip); > + /* Pinctrl_desc */ > + pctl->pinctrl_desc.name = "sx150x-pinctrl"; > + pctl->pinctrl_desc.pctlops = &sx150x_pinctrl_ops; > + pctl->pinctrl_desc.confops = &sx150x_pinconf_ops; > + pctl->pinctrl_desc.pins = pctl->data->pins; > + pctl->pinctrl_desc.npins = pctl->data->npins; > + pctl->pinctrl_desc.owner = THIS_MODULE; > + > + pctl->pctldev = pinctrl_register(&pctl->pinctrl_desc, dev, pctl); > + if (IS_ERR(pctl->pctldev)) { > + dev_err(dev, "Failed to register pinctrl device\n"); > + return PTR_ERR(pctl->pctldev); > + } > > return 0; > } > > static struct i2c_driver sx150x_driver = { > .driver = { > - .name = "sx150x", > + .name = "sx150x-pinctrl", > .of_match_table = of_match_ptr(sx150x_of_match), > }, > .probe = sx150x_probe, >