From mboxrd@z Thu Jan 1 00:00:00 1970 From: Stefano Babic Date: Thu, 6 Sep 2018 11:33:10 +0200 Subject: [U-Boot] [PULL] Please pull u-boot-imx In-Reply-To: References: <9d19bc5e-b7aa-d7e3-8eeb-b211360edca0@denx.de> Message-ID: List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hi Peter, On 06/09/2018 11:23, Peter Robinson wrote: > Hi Stefano, > >> a new PR. I dropped the patches causing breakages on PowerPC boards, as >> well as the issue on GE boards. It ran on travis successfully. >> >> >> The following changes since commit 11ed312896c5f5814064c5d45dcb2f53dc121437: >> >> configs: am57xx: change default board name to beagle_x15 (2018-08-26 >> 12:26:16 -0400) >> >> are available in the Git repository at: >> >> git://www.denx.de/git/u-boot-imx.git master >> >> for you to fetch changes up to c1d1543ebc6e1fb026d0d7ac96d865faa7567555: >> >> mx7dsabresd: Add the qspi target to the list of supported defconfigs >> (2018-09-04 08:47:23 +0200) >> >> ---------------------------------------------------------------- >> Alex Kiernan (1): >> Cleanup CONFIG_BOOTDELAY on cl-som-imx7 >> >> Anson Huang (3): >> imx: mx7: psci: improve cpu hotplug flow >> imx: mx7: add gpc initialization for low power mode >> imx: mx7: add system suspend/resume support >> >> Fabio Estevam (1): >> mx7dsabresd: Add the qspi target to the list of supported defconfigs >> >> Martin Kaiser (1): >> watchdog: mx25: use the imx_watchdog driver for mx25 >> >> Stefan Agner (2): >> board: toradex: common: fail gracefully on missing NAND chip >> colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support >> >> Stefano Babic (1): >> imx: missing CONFIG_MII in mx7dsabresd_qspi_defconfig >> >> Ye Li (6): >> imx: imx6sx-sdb: Enable DM QSPI driver >> imx: imx6sx-sabreauto: convert to use DM QSPI driver >> imx: imx7d-sdb: Add DM QSPI support >> dts: imx6ul: Update alias to support DM >> dts: imx6ul_evk: Add DTS files for 14x14 EVK and 9x9 EVK boards >> imx: imx6ul_evk: Enable DM driver for iMX6UL EVK u-boot > > Are you aware of any issues on some imx6 devices in 2018.09? No. > The > hummingboard2 (imx6q) hangs for me just after the output below, even > with the above PR, it works fine with a imx6sx device (udoo neo). I'm > sure I've seen something on the list that might be related but I can't > find it. :-( > > Sorry for picking this up so late in the cycle. I can just try to test on another mx6q boar if I get enough time, but of course this is not a great test. Regards, Stefano > > Peter > > U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 20:28:15 +0000) > Trying to boot from MMC1 > > > U-Boot 2018.09-rc3 (Sep 05 2018 - 20:28:15 +0000) > > CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) > CPU: Extended Commercial temperature grade (-20C to 105C) at 25C > Reset cause: POR > Board: MX6 HummingBoard2 (som rev 1.5) > DRAM: 2 GiB > MMC: FSL_SDHC: 0, FSL_SDHC: 1 > Loading Environment from MMC... *** Warning - bad CRC, using default environment > > No panel detected: default to HDMI > Display: HDMI (1024x768) > In: serial > Out: serial > Err: serial > -- ===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================