From mboxrd@z Thu Jan 1 00:00:00 1970 From: Kuninori Morimoto Date: Wed, 14 Jul 2010 07:01:16 +0000 Subject: [PATCH] ARM: mach-shmobile: ap4evb: Add ts_get_pendown_state for Message-Id: List-Id: References: In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: linux-sh@vger.kernel.org This function is necessary to ensure the detection of pen-down. This patch support both QHD / WVGA pannel. Tested-by: Tony SIM Signed-off-by: Kuninori Morimoto --- This patch is depend on [PATCH] ARM: mach-shmobile: ap4evb: Add LCD panel selection # above patch got "Applied, thanks" from Paul # But I can not find it on latest Paul's git... arch/arm/mach-shmobile/board-ap4evb.c | 78 ++++++++++++++++++++++++++------- 1 files changed, 62 insertions(+), 16 deletions(-) diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c index e8a9d79..9686012 100644 --- a/arch/arm/mach-shmobile/board-ap4evb.c +++ b/arch/arm/mach-shmobile/board-ap4evb.c @@ -576,12 +576,74 @@ static struct platform_device *ap4evb_devices[] __initdata = { &sh_mmcif_device }; +/* + * FIXME !! + * + * gpio_no_direction + * gpio_pull_up + * are quick_hack. + * + * current gpio frame work doesn't have + * the method to control only pull up/down/free. + * this function should be replaced by correct gpio function + */ +static void __init gpio_no_direction(u32 addr) +{ + __raw_writeb(0x00, addr); +} + +static void __init gpio_pull_up(u32 addr) +{ + u8 data = __raw_readb(addr); + + data &= 0x0F; + data |= 0xC0; + __raw_writeb(data, addr); +} + /* TouchScreen */ #define IRQ28 evt2irq(0x3380) /* IRQ28A */ #define IRQ7 evt2irq(0x02e0) /* IRQ7A */ +static int ts_get_pendown_state(void) +{ + int val1, val2; + + gpio_free(GPIO_FN_IRQ28_123); + gpio_free(GPIO_FN_IRQ7_40); + + gpio_request(GPIO_PORT123, NULL); + gpio_request(GPIO_PORT40, NULL); + + gpio_direction_input(GPIO_PORT123); + gpio_direction_input(GPIO_PORT40); + + val1 = gpio_get_value(GPIO_PORT123); + val2 = gpio_get_value(GPIO_PORT40); + + gpio_request(GPIO_FN_IRQ28_123, NULL); /* for QHD */ + gpio_request(GPIO_FN_IRQ7_40, NULL); /* for WVGA */ + + return val1 ^ val2; +} + +#define PORT40CR 0xE6051028 +#define PORT123CR 0xE605007B +static int ts_init(void) +{ + gpio_request(GPIO_FN_IRQ28_123, NULL); /* for QHD */ + gpio_request(GPIO_FN_IRQ7_40, NULL); /* for WVGA */ + + gpio_pull_up(PORT40CR); + gpio_pull_up(PORT123CR); + + return 0; +} + static struct tsc2007_platform_data tsc2007_info = { .model = 2007, .x_plate_ohms = 180, + .get_pendown_state = ts_get_pendown_state, + .init_platform_hw = ts_init, }; static struct i2c_board_info tsc_device = { @@ -625,20 +687,6 @@ static void __init ap4evb_map_io(void) shmobile_setup_console(); } -/* - * FIXME !! - * - * gpio_no_direction is quick_hack. - * - * current gpio frame work doesn't have - * the method to control only pull up/down/free. - * this function should be replaced by correct gpio function - */ -static void __init gpio_no_direction(u32 addr) -{ - __raw_writeb(0x00, addr); -} - #define GPIO_PORT9CR 0xE6051009 #define GPIO_PORT10CR 0xE605100A @@ -784,7 +832,6 @@ static void __init ap4evb_init(void) gpio_request(GPIO_FN_KEYIN4, NULL); /* enable TouchScreen */ - gpio_request(GPIO_FN_IRQ28_123, NULL); set_irq_type(IRQ28, IRQ_TYPE_LEVEL_LOW); tsc_device.irq = IRQ28; @@ -860,7 +907,6 @@ static void __init ap4evb_init(void) lcdc_info.ch[0].lcd_size_cfg.height = 91; /* enable TouchScreen */ - gpio_request(GPIO_FN_IRQ7_40, NULL); set_irq_type(IRQ7, IRQ_TYPE_LEVEL_LOW); tsc_device.irq = IRQ7; -- 1.7.0.4