Alsa-Devel Archive on lore.kernel.org
 help / color / Atom feed
From: Michael Walle <michael@walle.cc>
To: alsa-devel@alsa-project.org, linux-kernel@vger.kernel.org
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>,
	patches@opensource.cirrus.com, Takashi Iwai <tiwai@suse.com>,
	Liam Girdwood <lgirdwood@gmail.com>,
	Michael Walle <michael@walle.cc>, Mark Brown <broonie@kernel.org>
Subject: [alsa-devel] [PATCH v2] ASoC: wm8904: configure sysclk/FLL automatically
Date: Fri,  8 Nov 2019 21:31:52 +0100
Message-ID: <20191108203152.19098-1-michael@walle.cc> (raw)

This adds a new mode WM8904_CLK_AUTO which automatically enables the FLL
if a frequency different than the MCLK is set.

These additions make the codec work with the simple-card driver in
general and especially in systems where the MCLK doesn't match the
required clock.

Signed-off-by: Michael Walle <michael@walle.cc>
---
changes since v1:
 - replaced second clk_get_rate() with mclk_freq

Please note that the v1 patch might still be pending for moderator
approval.

 sound/soc/codecs/wm8904.c | 72 ++++++++++++++++++++++++---------------
 sound/soc/codecs/wm8904.h |  1 +
 2 files changed, 45 insertions(+), 28 deletions(-)

diff --git a/sound/soc/codecs/wm8904.c b/sound/soc/codecs/wm8904.c
index bcb3c9d5abf0..2a7d23a5daa8 100644
--- a/sound/soc/codecs/wm8904.c
+++ b/sound/soc/codecs/wm8904.c
@@ -1410,34 +1410,6 @@ static int wm8904_hw_params(struct snd_pcm_substream *substream,
 	return 0;
 }
 
-
-static int wm8904_set_sysclk(struct snd_soc_dai *dai, int clk_id,
-			     unsigned int freq, int dir)
-{
-	struct snd_soc_component *component = dai->component;
-	struct wm8904_priv *priv = snd_soc_component_get_drvdata(component);
-
-	switch (clk_id) {
-	case WM8904_CLK_MCLK:
-		priv->sysclk_src = clk_id;
-		priv->mclk_rate = freq;
-		break;
-
-	case WM8904_CLK_FLL:
-		priv->sysclk_src = clk_id;
-		break;
-
-	default:
-		return -EINVAL;
-	}
-
-	dev_dbg(dai->dev, "Clock source is %d at %uHz\n", clk_id, freq);
-
-	wm8904_configure_clocking(component);
-
-	return 0;
-}
-
 static int wm8904_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
 {
 	struct snd_soc_component *component = dai->component;
@@ -1824,6 +1796,50 @@ static int wm8904_set_fll(struct snd_soc_dai *dai, int fll_id, int source,
 	return 0;
 }
 
+static int wm8904_set_sysclk(struct snd_soc_dai *dai, int clk_id,
+			     unsigned int freq, int dir)
+{
+	struct snd_soc_component *component = dai->component;
+	struct wm8904_priv *priv = snd_soc_component_get_drvdata(component);
+	unsigned long mclk_freq;
+	int ret;
+
+	switch (clk_id) {
+	case WM8904_CLK_AUTO:
+		mclk_freq = clk_get_rate(priv->mclk);
+		/* enable FLL if a different sysclk is desired */
+		if (mclk_freq != freq) {
+			priv->sysclk_src = WM8904_CLK_FLL;
+			ret = wm8904_set_fll(dai, WM8904_FLL_MCLK,
+					     WM8904_FLL_MCLK,
+					     mclk_freq, freq);
+			if (ret)
+				return ret;
+			break;
+		}
+		clk_id = WM8904_CLK_MCLK;
+		/* fallthrough */
+
+	case WM8904_CLK_MCLK:
+		priv->sysclk_src = clk_id;
+		priv->mclk_rate = freq;
+		break;
+
+	case WM8904_CLK_FLL:
+		priv->sysclk_src = clk_id;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	dev_dbg(dai->dev, "Clock source is %d at %uHz\n", clk_id, freq);
+
+	wm8904_configure_clocking(component);
+
+	return 0;
+}
+
 static int wm8904_digital_mute(struct snd_soc_dai *codec_dai, int mute)
 {
 	struct snd_soc_component *component = codec_dai->component;
diff --git a/sound/soc/codecs/wm8904.h b/sound/soc/codecs/wm8904.h
index c1bca52f9927..de6340446b1f 100644
--- a/sound/soc/codecs/wm8904.h
+++ b/sound/soc/codecs/wm8904.h
@@ -10,6 +10,7 @@
 #ifndef _WM8904_H
 #define _WM8904_H
 
+#define WM8904_CLK_AUTO 0
 #define WM8904_CLK_MCLK 1
 #define WM8904_CLK_FLL  2
 
-- 
2.20.1

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel

             reply index

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-08 20:31 Michael Walle [this message]
2019-11-11 16:27 ` Charles Keepax

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191108203152.19098-1-michael@walle.cc \
    --to=michael@walle.cc \
    --cc=alsa-devel@alsa-project.org \
    --cc=broonie@kernel.org \
    --cc=ckeepax@opensource.cirrus.com \
    --cc=lgirdwood@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=patches@opensource.cirrus.com \
    --cc=tiwai@suse.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Alsa-Devel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/alsa-devel/0 alsa-devel/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 alsa-devel alsa-devel/ https://lore.kernel.org/alsa-devel \
		alsa-devel@alsa-project.org
	public-inbox-index alsa-devel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.alsa-project.alsa-devel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git