Alsa-Devel Archive on lore.kernel.org
 help / color / Atom feed
From: Matt Flax <flatmax@flatmax.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>,
	alsa-devel@alsa-project.org,
	Florian Fainelli <f.fainelli@gmail.com>,
	Scott Branden <sbranden@broadcom.com>,
	Ray Jui <rjui@broadcom.com>, Takashi Iwai <tiwai@suse.com>,
	YueHaibing <yuehaibing@huawei.com>,
	linux-kernel@vger.kernel.org, Liam Girdwood <lgirdwood@gmail.com>,
	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
	Mark Brown <broonie@kernel.org>,
	bcm-kernel-feedback-list@broadcom.com,
	Allison Randal <allison@lohutok.net>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Thomas Gleixner <tglx@linutronix.de>,
	linux-arm-kernel@lists.infradead.org,
	linux-rpi-kernel@lists.infradead.org
Subject: Re: [PATCH] ASoC: bcm2835-i2s: substream alignment now independent in hwparams
Date: Fri, 27 Mar 2020 10:56:50 +1100
Message-ID: <d0684926-3f7a-0b97-a298-4088925442a4@flatmax.org> (raw)
In-Reply-To: <20200324090823.20754-1-flatmax@flatmax.org>


Should this patch be handled through the ALSA team the R. Pi team or the 
BCM team ?


thanks

Matt

On 24/3/20 8:08 pm, Matt Flax wrote:
> Substream sample alignment was being set in hwparams for both
> substreams at the same time. This became a problem when	the Audio
> Injector isolated sound card needed to offset sample alignment
> for high sample	rates. The latency difference between playback
> and capture occurs because of the digital isolation chip
> propagation time, particularly when the codec is master and
> the DAC return is twice delayed.
>
> This patch sets sample alignment registers  based on the substream
> direction in hwparams. This gives the machine driver more control
> over sample alignment in the bcm2835 i2s driver.
>
> Signed-off-by: Matt Flax <flatmax@flatmax.org>
> ---
>   sound/soc/bcm/bcm2835-i2s.c | 36 +++++++++++++++++++-----------------
>   1 file changed, 19 insertions(+), 17 deletions(-)
>
> diff --git a/sound/soc/bcm/bcm2835-i2s.c b/sound/soc/bcm/bcm2835-i2s.c
> index e6a12e271b07..9db542699a13 100644
> --- a/sound/soc/bcm/bcm2835-i2s.c
> +++ b/sound/soc/bcm/bcm2835-i2s.c
> @@ -493,11 +493,6 @@ static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream,
>   		return -EINVAL;
>   	}
>   
> -	bcm2835_i2s_calc_channel_pos(&rx_ch1_pos, &rx_ch2_pos,
> -		rx_mask, slot_width, data_delay, odd_slot_offset);
> -	bcm2835_i2s_calc_channel_pos(&tx_ch1_pos, &tx_ch2_pos,
> -		tx_mask, slot_width, data_delay, odd_slot_offset);
> -
>   	/*
>   	 * Transmitting data immediately after frame start, eg
>   	 * in left-justified or DSP mode A, only works stable
> @@ -508,19 +503,26 @@ static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream,
>   			"Unstable slave config detected, L/R may be swapped");
>   
>   	/*
> -	 * Set format for both streams.
> -	 * We cannot set another frame length
> -	 * (and therefore word length) anyway,
> -	 * so the format will be the same.
> +	 * Set format on a per stream basis.
> +	 * The alignment format can be different depending on direction.
>   	 */
> -	regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG,
> -		  format
> -		| BCM2835_I2S_CH1_POS(rx_ch1_pos)
> -		| BCM2835_I2S_CH2_POS(rx_ch2_pos));
> -	regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG,
> -		  format
> -		| BCM2835_I2S_CH1_POS(tx_ch1_pos)
> -		| BCM2835_I2S_CH2_POS(tx_ch2_pos));
> +	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE) {
> +		bcm2835_i2s_calc_channel_pos(&rx_ch1_pos, &rx_ch2_pos,
> +			rx_mask, slot_width, data_delay, odd_slot_offset);
> +		regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG,
> +			  format
> +			| BCM2835_I2S_CH1_POS(rx_ch1_pos)
> +			| BCM2835_I2S_CH2_POS(rx_ch2_pos));
> +	}
> +
> +	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
> +		bcm2835_i2s_calc_channel_pos(&tx_ch1_pos, &tx_ch2_pos,
> +			tx_mask, slot_width, data_delay, odd_slot_offset);
> +		regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG,
> +			  format
> +			| BCM2835_I2S_CH1_POS(tx_ch1_pos)
> +			| BCM2835_I2S_CH2_POS(tx_ch2_pos));
> +	}
>   
>   	/* Setup the I2S mode */
>   

  reply index

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-03-24  9:08 Matt Flax
2020-03-26 23:56 ` Matt Flax [this message]
2020-03-27  0:30   ` Matt Flax
2020-03-27 13:23     ` Matthias Reichl
2020-03-27 21:50       ` Matt Flax
2020-03-28 11:59         ` Matthias Reichl
2020-03-28 23:47           ` Matt Flax
2020-03-29 11:01             ` Matthias Reichl
2020-03-27 13:07   ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=d0684926-3f7a-0b97-a298-4088925442a4@flatmax.org \
    --to=flatmax@flatmax.org \
    --cc=allison@lohutok.net \
    --cc=alsa-devel@alsa-project.org \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=broonie@kernel.org \
    --cc=f.fainelli@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=kstewart@linuxfoundation.org \
    --cc=lgirdwood@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=nsaenzjulienne@suse.de \
    --cc=rjui@broadcom.com \
    --cc=sbranden@broadcom.com \
    --cc=tglx@linutronix.de \
    --cc=tiwai@suse.com \
    --cc=yuehaibing@huawei.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Alsa-Devel Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/alsa-devel/0 alsa-devel/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 alsa-devel alsa-devel/ https://lore.kernel.org/alsa-devel \
		alsa-devel@alsa-project.org
	public-inbox-index alsa-devel

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.alsa-project.alsa-devel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git