ATH10K Archive on
 help / color / Atom feed
* [PATCH 0/3] Channels in licensed bands, noise floor override
@ 2017-03-16 15:13 Simon Wunderlich
  2017-03-16 15:13 ` [PATCH 1/3] ath9k: Support channels in licensed bands Simon Wunderlich
                   ` (2 more replies)
  0 siblings, 3 replies; 12+ messages in thread
From: Simon Wunderlich @ 2017-03-16 15:13 UTC (permalink / raw)
  To: ath10k, ath9k-devel; +Cc: linux-wireless, Simon Wunderlich

This series contains two patches to enable channels in licensed bands.
Note that there are quite a few requirements to enable those:

 * channels must be explicitly enabled using a licensed band kernel config
   which contains a warning
 * it depends on CFG80211_CERTIFICATION_ONUS
 * users must install a custom regdb, since channels in those licensed
   bands are not included in the standard regdb

The ath9k patch has been proposed two times and rejected, but it also
included some channels on fractional center frequencies, which is not
the case this time (this would require more changes in mac80211 and
also userspace). The other concern about useres accidently tuning
should not be a problem based on the requirements mentioned above. I've
added another patch doing the same thing for ath10k.

Here is some more info on our need/background:

"We are working on a project that involves the use of Public Safety 
channels (4.9x GHz). It is typical 'First Responder' scenario where a 
communication network infrastructure should be set up in catastrophe 

As this is a controlled and managed network, the organization setting up 
the network has control over the channels that are being used, when and 
for how long and in which geographical area.  The enforcement of such a 
temporary license is a major requirement in this project.

To reduce the cost for the equipment (compared to commercial offerings 
in the 4k USD range), the outdoor devices run on hardened, but standard 
embedded hardware with a recent linux kernel and use Atheros radios.

We believe, that driver support for 4.9GHz channels should be included 
in the Linux kernel, as the driver just exposes specified hardware 
features which are disabled by default via

a) a separate compile-time flag. This is similar to the code used for 
compliance testing.

b) The default CRDA should (and does) not enable such channels.

Those two safeguards seem sufficient to protect against accidental misuse."

The third patch is adding an experimental debug option to override
the noise floor level, which is usually calibrated automatically.


Ben Greear (1):
  ath9k: Support channels in licensed bands

Simon Wunderlich (2):
  ath10k: add support for channels in licensed bands
  ath9k: add noise floor override option

 drivers/net/wireless/ath/ath10k/Kconfig      | 20 +++++++++
 drivers/net/wireless/ath/ath10k/core.h       |  4 ++
 drivers/net/wireless/ath/ath10k/mac.c        |  9 ++++
 drivers/net/wireless/ath/ath10k/wmi.c        |  7 +++-
 drivers/net/wireless/ath/ath9k/Kconfig       | 20 +++++++++
 drivers/net/wireless/ath/ath9k/ath9k.h       |  2 +-
 drivers/net/wireless/ath/ath9k/calib.c       |  5 ++-
 drivers/net/wireless/ath/ath9k/common-init.c | 35 ++++++++++++----
 drivers/net/wireless/ath/ath9k/debug.c       | 62 ++++++++++++++++++++++++++++
 drivers/net/wireless/ath/ath9k/hw.h          |  5 ++-
 10 files changed, 155 insertions(+), 14 deletions(-)


ath10k mailing list

^ permalink raw reply	[flat|nested] 12+ messages in thread

end of thread, back to index

Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-03-16 15:13 [PATCH 0/3] Channels in licensed bands, noise floor override Simon Wunderlich
2017-03-16 15:13 ` [PATCH 1/3] ath9k: Support channels in licensed bands Simon Wunderlich
2017-03-17 13:40   ` Zefir Kurtisi
2017-03-17 14:02     ` Simon Wunderlich
2017-03-17 16:00     ` [PATCHv2 " Simon Wunderlich
2017-03-16 15:13 ` [PATCH 2/3] ath10k: add support for " Simon Wunderlich
2017-03-17 18:49   ` Sebastian Gottschall
2017-03-23  9:00     ` Simon Wunderlich
2017-03-16 15:13 ` [PATCH 3/3] ath9k: add noise floor override option Simon Wunderlich
2017-03-17  8:48   ` Janusz Dziedzic
2017-03-17  8:55     ` Simon Wunderlich
2017-03-17 12:44       ` Janusz Dziedzic

ATH10K Archive on

Archives are clonable:
	git clone --mirror ath10k/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 ath10k ath10k/ \
	public-inbox-index ath10k

Example config snippet for mirrors

Newsgroup available over NNTP:

AGPL code for this site: git clone