From mboxrd@z Thu Jan 1 00:00:00 1970 From: Martin Blumenstingl Date: Fri, 24 Jun 2016 14:34:28 +0200 Subject: [ath9k-devel] [PATCH RFC v3 1/3] Documentation: dt: net: add ath9k wireless device binding In-Reply-To: <20160624123430.4097-1-martin.blumenstingl@googlemail.com> References: <20160624123430.4097-1-martin.blumenstingl@googlemail.com> Message-ID: <20160624123430.4097-2-martin.blumenstingl@googlemail.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: ath9k-devel@lists.ath9k.org Add documentation how devicetree can be used to configure ath9k based devices. Signed-off-by: Martin Blumenstingl --- changes in v2 -> v3: - improved wording of the qca,disable-2ghz and qca,disable-5ghz properties - replaced qca,eeprom-name with qca,no-eeprom (the eeprom name is now built automatically within ath9k). The naming was chosen to stay consistent with other drivers (such as davicom-dm9000 and via-velocity) - added reference to the mac-address and local-mac-address properties - removed invalid device_type property from the example .../devicetree/bindings/net/wireless/qca,ath9k.txt | 46 ++++++++++++++++++++++ 1 file changed, 46 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt new file mode 100644 index 0000000..ff83fd4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt @@ -0,0 +1,46 @@ +* Qualcomm Atheros ath9k wireless devices + +This node provides properties for configuring the ath9k wireless device. The +node is expected to be specified as a child node of the PCI controller to +which the wireless chip is connected. + +Required properties: +- compatible: Should be "qca,ath9k" + +Optional properties: +- reg: Address and length of the register set for the device. +- qca,gpio-mask: The GPIO mask +- qca,gpio-val: The GPIO value +- qca,led-pin: The GPIO number to which the LED is connected +- qca,led-active-high: The LED is active when the GPIO is HIGH +- qca,clk-25mhz: Defines that at 25MHz clock is used +- qca,no-eeprom: Indicates that there is on physical EEPROM connected + to the ath9k wireless chip (in this case the + calibration / EEPROM data will be loaded from + userspace using the firmware mechanism) +- qca,check-eeprom-endianness: Allow checking the EEPROM endianness and + swapping of the EEPROM data if required +- qca,disable-2ghz: Overrides the settings from the EEPROM and disables + the 2.4GHz band, even if enabled in the EEPROM +- qca,disable-5ghz: Overrides the settings from the EEPROM and disables + the 5GHz band, even if enabled in the EEPROM +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory + +In this example, the node is defined as child node of the PCI controller. + +pci { + pcie at 0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath9k at 0,0 { + compatible = "qca,ath9k"; + reg = <0 0 0 0 0>; + qca,disable-5ghz; + }; + }; +}; -- 2.9.0