From mboxrd@z Thu Jan 1 00:00:00 1970 From: Martin Blumenstingl Date: Sun, 21 Aug 2016 16:31:03 +0200 Subject: [ath9k-devel] [PATCH v5 1/3] Documentation: dt: net: add ath9k wireless device binding In-Reply-To: <20160821143105.27487-1-martin.blumenstingl@googlemail.com> References: <20160709232834.31654-1-martin.blumenstingl@googlemail.com> <20160821143105.27487-1-martin.blumenstingl@googlemail.com> Message-ID: <20160821143105.27487-2-martin.blumenstingl@googlemail.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: ath9k-devel@lists.ath9k.org Add documentation how devicetree can be used to configure ath9k based devices. Signed-off-by: Martin Blumenstingl --- .../devicetree/bindings/net/wireless/qca,ath9k.txt | 47 ++++++++++++++++++++++ 1 file changed, 47 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt new file mode 100644 index 0000000..98065ad --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt @@ -0,0 +1,47 @@ +* Qualcomm Atheros ath9k wireless devices + +This node provides properties for configuring the ath9k wireless device. The +node is expected to be specified as a child node of the PCI controller to +which the wireless chip is connected. + +Required properties: +- compatible: For PCI and PCIe devices this should be an identifier following + the format as defined in "PCI Bus Binding to Open Firmware" + Revision 2.1. One of the possible formats is "pciVVVV,DDDD" + where VVVV is the PCI vendor ID and DDDD is PCI device ID. + +Optional properties: +- reg: Address and length of the register set for the device. +- qca,clk-25mhz: Defines that a 25MHz clock is used +- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the + ath9k wireless chip (in this case the calibration / + EEPROM data will be loaded from userspace using the + kernel firmware loader). +- qca,disable-2ghz: Overrides the settings from the EEPROM and disables the + 2.4GHz band. Setting this property is only needed + when the RF circuit does not support the 2.4GHz band + while it is enabled nevertheless in the EEPROM. +- qca,disable-5ghz: Overrides the settings from the EEPROM and disables the + 5GHz band. Setting this property is only needed when + the RF circuit does not support the 5GHz band while + it is enabled nevertheless in the EEPROM. +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory + +In this example, the node is defined as child node of the PCI controller. + +pci { + pcie at 0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath9k at 0,0 { + compatible = "pci168c,0030"; + reg = <0 0 0 0 0>; + qca,disable-5ghz; + }; + }; +}; -- 2.9.3