b.a.t.m.a.n.lists.open-mesh.org archive mirror
 help / color / mirror / Atom feed
From: "Linus Lüssing" <linus.luessing@saxnet.de>
To: b.a.t.m.a.n@lists.open-mesh.org
Cc: "Linus Lüssing" <linus.luessing@saxnet.de>
Subject: [B.A.T.M.A.N.] [PATCH 18/19] batman-adv: Still flood multicast packets we are not a receiver of
Date: Sat, 22 Jan 2011 02:21:41 +0100	[thread overview]
Message-ID: <1295659302-7171-19-git-send-email-linus.luessing@saxnet.de> (raw)
In-Reply-To: <1295659302-7171-1-git-send-email-linus.luessing@saxnet.de>

We may only optimize the multicast packet flow, if an mcast_mode has been
activated and if we are a multicast receiver of the same group. Otherwise
flood the multicast packet without optimizations.

This allows us to still flood multicast packets of protocols where it is
not easily possible for a multicast sender to be a multicast receiver of
the same group instead of dropping them (for instance IPv6 NDP).

This commit therefore also makes IPv6 usable again, if the
proact_tracking multicast mode has been activated.

Signed-off-by: Linus Lüssing <linus.luessing@saxnet.de>
---
 soft-interface.c |   28 ++++++++++++++++++++++++++--
 1 files changed, 26 insertions(+), 2 deletions(-)

diff --git a/batman-adv/soft-interface.c b/batman-adv/soft-interface.c
index 2f327c4..2b202ae 100644
--- a/batman-adv/soft-interface.c
+++ b/batman-adv/soft-interface.c
@@ -340,6 +340,31 @@ static int interface_change_mtu(struct net_device *dev, int new_mtu)
 	return 0;
 }
 
+static int mcast_may_optimize(uint8_t *dest, struct net_device *soft_iface)
+{
+	MC_LIST *mc_entry;
+	struct bat_priv *bat_priv = netdev_priv(soft_iface);
+	int mcast_mode = atomic_read(&bat_priv->mcast_mode);
+
+	if (mcast_mode != MCAST_MODE_PROACT_TRACKING)
+		return 0;
+
+	/* Still allow flooding of multicast packets of protocols where it is
+	 * not easily possible for a multicast sender to be a multicast
+	 * receiver of the same group (for instance IPv6 NDP) */
+	netif_addr_lock_bh(soft_iface);
+	netdev_for_each_mc_addr(mc_entry, soft_iface) {
+		if (memcmp(dest, mc_entry->MC_LIST_ADDR, ETH_ALEN))
+			continue;
+
+		netif_addr_unlock_bh(soft_iface);
+		return 1;
+	}
+	netif_addr_unlock_bh(soft_iface);
+
+	return 0;
+}
+
 int interface_tx(struct sk_buff *skb, struct net_device *soft_iface)
 {
 	struct ethhdr *ethhdr = (struct ethhdr *)skb->data;
@@ -392,8 +417,7 @@ int interface_tx(struct sk_buff *skb, struct net_device *soft_iface)
 
 		if (is_broadcast_ether_addr(ethhdr->h_dest))
 			bcast_dst = true;
-		else if (atomic_read(&bat_priv->mcast_mode) ==
-			 MCAST_MODE_PROACT_TRACKING)
+		else if (mcast_may_optimize(ethhdr->h_dest, soft_iface))
 			mcast_dst = true;
 		else
 			bcast_dst = true;
-- 
1.7.2.3


  parent reply	other threads:[~2011-01-22  1:21 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-01-22  1:21 [B.A.T.M.A.N.] B.A.T.M.A.N.-Advanced Multicast Optimizations, v2 Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 01/19] batman-adv: Add packet structures for multicast optimizations Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 02/19] batman-adv: Adding configurable variables " Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 03/19] batman-adv: compat macros/defines for local multicast group fetching Linus Lüssing
2011-01-23  0:50   ` Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 04/19] batman-adv: Attach local MCAs to OGMs Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 05/19] batman-adv: Add periodic multicast tracker timer Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 06/19] batman-adv: Buffer other originator's received MCA entries Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 07/19] batman-adv: Prepare and send own multicast tracker packets Linus Lüssing
2011-01-22 22:00   ` Simon Wunderlich
2011-01-30  4:49     ` Linus Lüssing
2011-01-23  0:52   ` Linus Lüssing
2011-01-23  2:52   ` Simon Wunderlich
2011-01-23  3:00   ` Simon Wunderlich
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 08/19] batman-adv: Add length check for (received) " Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 09/19] batman-adv: Route multicast " Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 10/19] batman-adv: Add/refresh entries to/in mcast forwarding table Linus Lüssing
2011-01-22 22:13   ` Simon Wunderlich
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 11/19] batman-adv: Output mcast forw table in debugfs Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 12/19] batman-adv: Purge timeouted entries in mcast forw table Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 13/19] batman-adv: Send own BAT_MCAST packets in proact_tracking multicast mode Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 14/19] batman-adv: Export broadcast packet ethernet header checks Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 15/19] batman-adv: Receive multicast data packets BAT_MCAST Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 16/19] batman-adv: Forward multicast data in proact_tracking mode Linus Lüssing
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 17/19] batman-adv: Add duplicate checks for multicast data Linus Lüssing
2011-01-22  1:21 ` Linus Lüssing [this message]
2011-01-22  1:21 ` [B.A.T.M.A.N.] [PATCH 19/19] batman-adv: Make number of (re)broadcasts configurable via sysfs Linus Lüssing
2011-01-22 16:16 ` [B.A.T.M.A.N.] B.A.T.M.A.N.-Advanced Multicast Optimizations, v2 Linus Lüssing

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1295659302-7171-19-git-send-email-linus.luessing@saxnet.de \
    --to=linus.luessing@saxnet.de \
    --cc=b.a.t.m.a.n@lists.open-mesh.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).