From: Simon Wunderlich <sw@simonwunderlich.de>
To: b.a.t.m.a.n@lists.open-mesh.org
Cc: Simon Wunderlich <simon@open-mesh.com>
Subject: [B.A.T.M.A.N.] [PATCHv3] batman-adv: drop QinQ claim frames in bridge loop avoidance
Date: Mon, 23 Jun 2014 15:55:36 +0200 [thread overview]
Message-ID: <1403531736-12460-1-git-send-email-sw@simonwunderlich.de> (raw)
From: Simon Wunderlich <simon@open-mesh.com>
Since bridge loop avoidance only supports untagged or simple 802.1q
tagged VLAN claim frames, claim frames with stacked VLAN headers (QinQ)
should be detected and dropped. Transporting the over the mesh may cause
problems on the receivers, or create bogus entries in the local tt
tables.
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
---
Changes to PATCHv2 (thanks Marek):
* move check into bla_process_claim() to avoid code duplication
Changes to PATCHv1 (thanks Antonio):
* add short description, fix capitalization for return
* move drop debug message to batadv_bla_process_claim()
---
bridge_loop_avoidance.c | 44 ++++++++++++++++++++++++++++++++++----------
1 file changed, 34 insertions(+), 10 deletions(-)
diff --git a/bridge_loop_avoidance.c b/bridge_loop_avoidance.c
index 6f0d9ec..a957c81 100644
--- a/bridge_loop_avoidance.c
+++ b/bridge_loop_avoidance.c
@@ -800,11 +800,6 @@ static int batadv_check_claim_group(struct batadv_priv *bat_priv,
bla_dst = (struct batadv_bla_claim_dst *)hw_dst;
bla_dst_own = &bat_priv->bla.claim_dest;
- /* check if it is a claim packet in general */
- if (memcmp(bla_dst->magic, bla_dst_own->magic,
- sizeof(bla_dst->magic)) != 0)
- return 0;
-
/* if announcement packet, use the source,
* otherwise assume it is in the hw_src
*/
@@ -866,12 +861,13 @@ static int batadv_bla_process_claim(struct batadv_priv *bat_priv,
struct batadv_hard_iface *primary_if,
struct sk_buff *skb)
{
- struct batadv_bla_claim_dst *bla_dst;
+ struct batadv_bla_claim_dst *bla_dst, *bla_dst_own;
uint8_t *hw_src, *hw_dst;
- struct vlan_ethhdr *vhdr;
+ struct vlan_hdr *vhdr, vhdr_buf;
struct ethhdr *ethhdr;
struct arphdr *arphdr;
unsigned short vid;
+ int vlan_depth = 0;
__be16 proto;
int headlen;
int ret;
@@ -882,9 +878,24 @@ static int batadv_bla_process_claim(struct batadv_priv *bat_priv,
proto = ethhdr->h_proto;
headlen = ETH_HLEN;
if (vid & BATADV_VLAN_HAS_TAG) {
- vhdr = vlan_eth_hdr(skb);
- proto = vhdr->h_vlan_encapsulated_proto;
- headlen += VLAN_HLEN;
+ /* Traverse the VLAN/Ethertypes.
+ *
+ * At this point it is known that the first protocol is a VLAN
+ * header, so start checking at the encapsulated protocol.
+ *
+ * The depth of the VLAN headers is recorded to drop BLA claim
+ * frames encapsulated into multiple VLAN headers (QinQ).
+ */
+ do {
+ vhdr = skb_header_pointer(skb, headlen, VLAN_HLEN,
+ &vhdr_buf);
+ if (!vhdr)
+ return 0;
+
+ proto = vhdr->h_vlan_encapsulated_proto;
+ headlen += VLAN_HLEN;
+ vlan_depth++;
+ } while (proto == htons(ETH_P_8021Q));
}
if (proto != htons(ETH_P_ARP))
@@ -914,6 +925,19 @@ static int batadv_bla_process_claim(struct batadv_priv *bat_priv,
hw_src = (uint8_t *)arphdr + sizeof(struct arphdr);
hw_dst = hw_src + ETH_ALEN + 4;
bla_dst = (struct batadv_bla_claim_dst *)hw_dst;
+ bla_dst_own = &bat_priv->bla.claim_dest;
+
+ /* check if it is a claim frame in general */
+ if (memcmp(bla_dst->magic, bla_dst_own->magic,
+ sizeof(bla_dst->magic)) != 0)
+ return 0;
+
+ /* check if there is a claim frame encapsulated deeper in (QinQ) and
+ * drop that, as this is not supported by BLA but should also not be
+ * sent via the mesh.
+ */
+ if (vlan_depth > 1)
+ return 1;
/* check if it is a claim frame. */
ret = batadv_check_claim_group(bat_priv, primary_if, hw_src, hw_dst,
--
1.9.1
next reply other threads:[~2014-06-23 13:55 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-06-23 13:55 Simon Wunderlich [this message]
2014-06-24 15:22 ` [B.A.T.M.A.N.] [PATCHv3] batman-adv: drop QinQ claim frames in bridge loop avoidance Marek Lindner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1403531736-12460-1-git-send-email-sw@simonwunderlich.de \
--to=sw@simonwunderlich.de \
--cc=b.a.t.m.a.n@lists.open-mesh.org \
--cc=simon@open-mesh.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).