All of lore.kernel.org
 help / color / mirror / Atom feed
From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: mazziesaccount@gmail.com, matti.vaittinen@fi.rohmeurope.com
Cc: Lee Jones <lee.jones@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>,
	Wim Van Sebroeck <wim@linux-watchdog.org>,
	Guenter Roeck <linux@roeck-us.net>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-power@fi.rohmeurope.com, linux-watchdog@vger.kernel.org
Subject: [PATCH v3 3/4] wdt: Support wdt on ROHM BD9576MUF and BD9573MUF
Date: Tue, 29 Sep 2020 11:17:07 +0300	[thread overview]
Message-ID: <ce789c2dba0613edfd7398ee7f201ba89428402a.1601366711.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1601366711.git.matti.vaittinen@fi.rohmeurope.com>

Add Watchdog support for ROHM BD9576MUF and BD9573MUF PMICs which are
mainly used to power the R-Car series processors. The watchdog is
pinged using a GPIO and enabled using another GPIO. Additionally
watchdog time-out can be configured to HW prior starting the watchdog.
Watchdog timeout can be configured to detect only delayed ping or in
a window mode where also too fast pings are detected.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---

Changes from v2:
  - Replace bindings hw_margin_ms and rohm,hw-margin-min-ms with
    rohm,hw-timeout-ms

 drivers/watchdog/Kconfig      |  13 ++
 drivers/watchdog/Makefile     |   1 +
 drivers/watchdog/bd9576_wdt.c | 290 ++++++++++++++++++++++++++++++++++
 3 files changed, 304 insertions(+)
 create mode 100644 drivers/watchdog/bd9576_wdt.c

diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index ab7aad5a1e69..d042a517a946 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -172,6 +172,19 @@ config BD70528_WATCHDOG
 	  Alternatively say M to compile the driver as a module,
 	  which will be called bd70528_wdt.
 
+config BD957XMUF_WATCHDOG
+	tristate "ROHM BD9576MUF and BD9573MUF PMIC Watchdog"
+	depends on MFD_ROHM_BD957XMUF
+	select WATCHDOG_CORE
+	help
+	  Support for the watchdog in the ROHM BD9576 and BD9573 PMICs.
+	  These PMIC ICs contain watchdog block which can be configured
+	  to toggle reset line if SoC fails to ping watchdog via GPIO.
+
+	  Say Y here to include support for the ROHM BD9576 or BD9573
+	  watchdog. Alternatively say M to compile the driver as a module,
+	  which will be called bd9576_wdt.
+
 config DA9052_WATCHDOG
 	tristate "Dialog DA9052 Watchdog"
 	depends on PMIC_DA9052 || COMPILE_TEST
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 97bed1d3d97c..14d75f98e3df 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -208,6 +208,7 @@ obj-$(CONFIG_XEN_WDT) += xen_wdt.o
 
 # Architecture Independent
 obj-$(CONFIG_BD70528_WATCHDOG) += bd70528_wdt.o
+obj-$(CONFIG_BD957XMUF_WATCHDOG) += bd9576_wdt.o
 obj-$(CONFIG_DA9052_WATCHDOG) += da9052_wdt.o
 obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
 obj-$(CONFIG_DA9062_WATCHDOG) += da9062_wdt.o
diff --git a/drivers/watchdog/bd9576_wdt.c b/drivers/watchdog/bd9576_wdt.c
new file mode 100644
index 000000000000..afef19ce01be
--- /dev/null
+++ b/drivers/watchdog/bd9576_wdt.c
@@ -0,0 +1,290 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2020 ROHM Semiconductors
+ *
+ * ROHM BD9576MUF and BD9573MUF Watchdog driver
+ */
+
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/rohm-bd957x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/watchdog.h>
+
+static bool nowayout;
+module_param(nowayout, bool, 0);
+MODULE_PARM_DESC(nowayout,
+		"Watchdog cannot be stopped once started (default=\"false\")");
+
+#define HW_MARGIN_MIN 2
+#define HW_MARGIN_MAX 4416
+#define BD957X_WDT_DEFAULT_MARGIN 4416
+
+struct bd9576_wdt_priv {
+	struct gpio_desc	*gpiod_ping;
+	struct gpio_desc	*gpiod_en;
+	struct device		*dev;
+	struct regmap		*regmap;
+	bool			always_running;
+	struct watchdog_device	wdd;
+};
+
+static void bd9576_wdt_disable(struct bd9576_wdt_priv *priv)
+{
+	gpiod_set_value_cansleep(priv->gpiod_en, 0);
+}
+
+static int bd9576_wdt_ping(struct watchdog_device *wdd)
+{
+	struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	/* Pulse */
+	gpiod_set_value_cansleep(priv->gpiod_ping, 1);
+	gpiod_set_value_cansleep(priv->gpiod_ping, 0);
+
+	return 0;
+}
+
+static int bd9576_wdt_start(struct watchdog_device *wdd)
+{
+	struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	gpiod_set_value_cansleep(priv->gpiod_en, 1);
+
+	return bd9576_wdt_ping(wdd);
+}
+
+static int bd9576_wdt_stop(struct watchdog_device *wdd)
+{
+	struct bd9576_wdt_priv *priv = watchdog_get_drvdata(wdd);
+
+	if (!priv->always_running)
+		bd9576_wdt_disable(priv);
+	else
+		set_bit(WDOG_HW_RUNNING, &wdd->status);
+
+	return 0;
+}
+
+static const struct watchdog_info bd957x_wdt_ident = {
+	.options	= WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING |
+			  WDIOF_SETTIMEOUT,
+	.identity	= "BD957x Watchdog",
+};
+
+static const struct watchdog_ops bd957x_wdt_ops = {
+	.owner		= THIS_MODULE,
+	.start		= bd9576_wdt_start,
+	.stop		= bd9576_wdt_stop,
+	.ping		= bd9576_wdt_ping,
+};
+
+/* Unit is hundreds of uS */
+#define FASTNG_MIN 23
+
+static int find_closest_fast(int target, int *sel, int *val)
+{
+	int i;
+	int window = FASTNG_MIN;
+
+	for (i = 0; i < 8 && window < target; i++)
+		window <<= 1;
+
+	*val = window;
+	*sel = i;
+
+	if (i == 8)
+		return -EINVAL;
+
+	return 0;
+
+}
+
+static int find_closest_slow_by_fast(int fast_val, int target, int *slowsel)
+{
+	int sel;
+	static const int multipliers[] = {2, 3, 7, 15};
+
+	for (sel = 0; sel < ARRAY_SIZE(multipliers) &&
+	     multipliers[sel] * fast_val < target; sel++)
+		;
+
+	if (sel == ARRAY_SIZE(multipliers))
+		return -EINVAL;
+
+	*slowsel = sel;
+
+	return 0;
+}
+
+static int find_closest_slow(int target, int *slow_sel, int *fast_sel)
+{
+	static const int multipliers[] = {2, 3, 7, 15};
+	int i, j;
+	int val = 0;
+	int window = FASTNG_MIN;
+
+	for (i = 0; i < 8; i++) {
+		for (j = 0; j < ARRAY_SIZE(multipliers); j++) {
+			int slow;
+
+			slow = window * multipliers[j];
+			if (slow >= target && (!val || slow < val)) {
+				val = slow;
+				*fast_sel = i;
+				*slow_sel = j;
+			}
+		}
+		window <<= 1;
+	}
+	if (!val)
+		return -EINVAL;
+
+	return 0;
+}
+
+#define BD957X_WDG_TYPE_WINDOW BIT(5)
+#define BD957X_WDG_TYPE_SLOW 0
+#define BD957X_WDG_TYPE_MASK BIT(5)
+#define BD957X_WDG_NG_RATIO_MASK 0x18
+#define BD957X_WDG_FASTNG_MASK 0x7
+
+static int bd957x_set_wdt_mode(struct bd9576_wdt_priv *priv, int hw_margin,
+			       int hw_margin_min)
+{
+	int ret, fastng, slowng, type, reg, mask;
+	struct device *dev = priv->dev;
+
+	/* convert to 100uS */
+	hw_margin *= 10;
+	hw_margin_min *= 10;
+	if (hw_margin_min) {
+		int min;
+
+		type = BD957X_WDG_TYPE_WINDOW;
+		dev_dbg(dev, "Setting type WINDOW 0x%x\n", type);
+		ret = find_closest_fast(hw_margin_min, &fastng, &min);
+		if (ret) {
+			dev_err(dev, "bad WDT window for fast timeout\n");
+			return ret;
+		}
+
+		ret = find_closest_slow_by_fast(min, hw_margin, &slowng);
+		if (ret) {
+			dev_err(dev, "bad WDT window\n");
+			return ret;
+		}
+
+	} else {
+		type = BD957X_WDG_TYPE_SLOW;
+		dev_dbg(dev, "Setting type SLOW 0x%x\n", type);
+		ret = find_closest_slow(hw_margin, &slowng, &fastng);
+		if (ret) {
+			dev_err(dev, "bad WDT window\n");
+			return ret;
+		}
+	}
+
+	slowng <<= ffs(BD957X_WDG_NG_RATIO_MASK) - 1;
+	reg = type | slowng | fastng;
+	mask = BD957X_WDG_TYPE_MASK | BD957X_WDG_NG_RATIO_MASK |
+	       BD957X_WDG_FASTNG_MASK;
+	ret = regmap_update_bits(priv->regmap, BD957X_REG_WDT_CONF,
+				 mask, reg);
+
+	return ret;
+}
+
+static int bd9576_wdt_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->parent->of_node;
+	struct bd9576_wdt_priv *priv;
+	u32 hw_margin[2];
+	u32 hw_margin_max = BD957X_WDT_DEFAULT_MARGIN, hw_margin_min = 0;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	priv->dev = dev;
+	priv->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!priv->regmap) {
+		dev_err(dev, "No regmap found\n");
+		return -ENODEV;
+	}
+
+	priv->gpiod_en = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
+						     "rohm,watchdog-enable-gpios",
+						     0, GPIOD_OUT_LOW,
+						     "watchdog-enable");
+	if (IS_ERR(priv->gpiod_en))
+		return dev_err_probe(dev, PTR_ERR(priv->gpiod_en),
+			      "getting watchdog-enable GPIO failed\n");
+
+	priv->gpiod_ping = devm_gpiod_get_from_of_node(dev, dev->parent->of_node,
+						     "rohm,watchdog-ping-gpios",
+						     0, GPIOD_OUT_LOW,
+						     "watchdog-ping");
+	if (IS_ERR(priv->gpiod_ping))
+		return dev_err_probe(dev, PTR_ERR(priv->gpiod_ping),
+				     "getting watchdog-ping GPIO failed\n");
+
+	ret = of_property_read_variable_u32_array(np, "rohm,hw-timeout-ms",
+						  &hw_margin[0], 1, 2);
+	if (ret < 0 && ret != -EINVAL)
+		return ret;
+
+	if (ret == 1)
+		hw_margin_max = hw_margin[0];
+
+	if (ret == 2) {
+		hw_margin_max = hw_margin[1];
+		hw_margin_min = hw_margin[0];
+	}
+
+	ret = bd957x_set_wdt_mode(priv, hw_margin_max, hw_margin_min);
+	if (ret)
+		return ret;
+
+	priv->always_running = of_property_read_bool(np, "always-running");
+
+	watchdog_set_drvdata(&priv->wdd, priv);
+
+	priv->wdd.info			= &bd957x_wdt_ident;
+	priv->wdd.ops			= &bd957x_wdt_ops;
+	priv->wdd.min_hw_heartbeat_ms	= hw_margin_min;
+	priv->wdd.max_hw_heartbeat_ms	= hw_margin_max;
+	priv->wdd.parent		= dev;
+	priv->wdd.timeout		= (hw_margin_max / 2) * 1000;
+
+	watchdog_init_timeout(&priv->wdd, 0, dev);
+	watchdog_set_nowayout(&priv->wdd, nowayout);
+
+	watchdog_stop_on_reboot(&priv->wdd);
+
+	if (priv->always_running)
+		bd9576_wdt_start(&priv->wdd);
+
+	return devm_watchdog_register_device(dev, &priv->wdd);
+}
+
+static struct platform_driver bd9576_wdt_driver = {
+	.driver	= {
+		.name = "bd9576-wdt",
+	},
+	.probe	= bd9576_wdt_probe,
+};
+
+module_platform_driver(bd9576_wdt_driver);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD9576/BD9573 Watchdog driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:bd9576-wdt");
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

  parent reply	other threads:[~2020-09-29  8:17 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-29  8:14 [PATCH v3 0/4] Support ROHM BD9576MUF and BD9573MUF PMICs Matti Vaittinen
2020-09-29  8:15 ` [PATCH v3 1/4] dt_bindings: mfd: Add " Matti Vaittinen
2020-09-29 14:53   ` Rob Herring
2020-09-29  8:16 ` [PATCH v3 2/4] mfd: Support ROHM BD9576MUF and BD9573MUF Matti Vaittinen
2020-09-29  8:17 ` Matti Vaittinen [this message]
2020-10-01 15:30   ` [PATCH v3 3/4] wdt: Support wdt on " Guenter Roeck
2020-09-29  8:17 ` [PATCH v3 4/4] MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers Matti Vaittinen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=ce789c2dba0613edfd7398ee7f201ba89428402a.1601366711.git.matti.vaittinen@fi.rohmeurope.com \
    --to=matti.vaittinen@fi.rohmeurope.com \
    --cc=devicetree@vger.kernel.org \
    --cc=lee.jones@linaro.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-power@fi.rohmeurope.com \
    --cc=linux-watchdog@vger.kernel.org \
    --cc=linux@roeck-us.net \
    --cc=mazziesaccount@gmail.com \
    --cc=robh+dt@kernel.org \
    --cc=wim@linux-watchdog.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.