[PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000

From: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
To: Andrew Lunn <andrew@lunn.ch>,
	Heiner Kallweit <hkallweit1@gmail.com>,
	Russell King <linux@armlinux.org.uk>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>
Cc: linux-kernel@vger.kernel.org, netdev@vger.kernel.org,
	Oleksij Rempel <o.rempel@pengutronix.de>
Subject: [PATCH v6 net-next 0/5] add PLCA RS support and onsemi NCN26000
Date: Sat, 10 Dec 2022 23:45:48 +0100	[thread overview]
Message-ID: <cover.1670712151.git.piergiorgio.beruto@gmail.com> (raw)

This patchset adds support for getting/setting the Physical Layer 
Collision Avoidace (PLCA) Reconciliation Sublayer (RS) configuration and
status on Ethernet PHYs that supports it.

PLCA is a feature that provides improved media-access performance in terms
of throughput, latency and fairness for multi-drop (P2MP) half-duplex PHYs.
PLCA is defined in Clause 148 of the IEEE802.3 specifications as amended
by 802.3cg-2019. Currently, PLCA is supported by the 10BASE-T1S single-pair
Ethernet PHY defined in the same standard and related amendments. The OPEN
Alliance SIG TC14 defines additional specifications for the 10BASE-T1S PHY,
including a standard register map for PHYs that embeds the PLCA RS (see
PLCA management registers at https://www.opensig.org/about/specifications/).

The changes proposed herein add the appropriate ethtool netlink interface
for configuring the PLCA RS on PHYs that supports it. A separate patchset
further modifies the ethtool userspace program to show and modify the
configuration/status of the PLCA RS.

Additionally, this patchset adds support for the onsemi NCN26000
Industrial Ethernet 10BASE-T1S PHY that uses the newly added PLCA
infrastructure.

Piergiorgio Beruto (5):
  net/ethtool: add netlink interface for the PLCA RS
  drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY
  drivers/net/phy: add connection between ethtool and phylib for PLCA
  drivers/net/phy: add helpers to get/set PLCA configuration
  drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY

 Documentation/networking/ethtool-netlink.rst | 138 ++++++++++
 MAINTAINERS                                  |  14 +
 drivers/net/phy/Kconfig                      |   7 +
 drivers/net/phy/Makefile                     |   1 +
 drivers/net/phy/mdio-open-alliance.h         |  47 ++++
 drivers/net/phy/ncn26000.c                   | 171 ++++++++++++
 drivers/net/phy/phy-c45.c                    | 183 +++++++++++++
 drivers/net/phy/phy-core.c                   |   5 +-
 drivers/net/phy/phy.c                        | 175 ++++++++++++
 drivers/net/phy/phy_device.c                 |  17 ++
 drivers/net/phy/phylink.c                    |   6 +-
 include/linux/ethtool.h                      |  12 +
 include/linux/phy.h                          |  83 ++++++
 include/uapi/linux/ethtool.h                 |   3 +
 include/uapi/linux/ethtool_netlink.h         |  25 ++
 net/ethtool/Makefile                         |   2 +-
 net/ethtool/common.c                         |   8 +
 net/ethtool/netlink.c                        |  29 ++
 net/ethtool/netlink.h                        |   6 +
 net/ethtool/plca.c                           | 272 +++++++++++++++++++
 20 files changed, 1201 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/phy/mdio-open-alliance.h
 create mode 100644 drivers/net/phy/ncn26000.c
 create mode 100644 net/ethtool/plca.c

-- 
2.37.4