From mboxrd@z Thu Jan 1 00:00:00 1970 From: Christoph Hellwig Subject: Re: [PATCH 06/14] block: lift setting the readahead size into the block layer Date: Thu, 10 Sep 2020 11:28:13 +0200 Message-ID: <20200910092813.GA27229@lst.de> References: <20200726150333.305527-1-hch@lst.de> <20200726150333.305527-7-hch@lst.de> <20200826220737.GA25613@redhat.com> <20200902151144.GA1738@lst.de> <20200902162007.GB5513@redhat.com> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: <20200902162007.GB5513@redhat.com> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: dm-devel-bounces@redhat.com Errors-To: dm-devel-bounces@redhat.com Content-Disposition: inline To: Mike Snitzer Cc: Jens Axboe , linux-raid@vger.kernel.org, martin.petersen@oracle.com, Hans de Goede , Richard Weinberger , Minchan Kim , drbd-dev@tron.linbit.com, linux-kernel@vger.kernel.org, linux-block@vger.kernel.org, Song Liu , dm-devel@redhat.com, linux-mtd@lists.infradead.org, linux-mm@kvack.org, linux-fsdevel@vger.kernel.org, cgroups@vger.kernel.org, Christoph Hellwig List-Id: dm-devel.ids On Wed, Sep 02, 2020 at 12:20:07PM -0400, Mike Snitzer wrote: > On Wed, Sep 02 2020 at 11:11am -0400, > Christoph Hellwig wrote: > > > On Wed, Aug 26, 2020 at 06:07:38PM -0400, Mike Snitzer wrote: > > > On Sun, Jul 26 2020 at 11:03am -0400, > > > Christoph Hellwig wrote: > > > > > > > Drivers shouldn't really mess with the readahead size, as that is a VM > > > > concept. Instead set it based on the optimal I/O size by lifting the > > > > algorithm from the md driver when registering the disk. Also set > > > > bdi->io_pages there as well by applying the same scheme based on > > > > max_sectors. > > > > > > > > Signed-off-by: Christoph Hellwig > > > > --- > > > > block/blk-settings.c | 5 ++--- > > > > block/blk-sysfs.c | 1 - > > > > block/genhd.c | 13 +++++++++++-- > > > > drivers/block/aoe/aoeblk.c | 2 -- > > > > drivers/block/drbd/drbd_nl.c | 12 +----------- > > > > drivers/md/bcache/super.c | 4 ---- > > > > drivers/md/dm-table.c | 3 --- > > > > drivers/md/raid0.c | 16 ---------------- > > > > drivers/md/raid10.c | 24 +----------------------- > > > > drivers/md/raid5.c | 13 +------------ > > > > 10 files changed, 16 insertions(+), 77 deletions(-) > > > > > > > > > In general these changes need a solid audit relative to stacking > > > drivers. That is, the limits stacking methods (blk_stack_limits) > > > vs lower level allocation methods (__device_add_disk). > > > > > > You optimized for lowlevel __device_add_disk establishing the bdi's > > > ra_pages and io_pages. That is at the beginning of disk allocation, > > > well before any build up of stacking driver's queue_io_opt() -- which > > > was previously done in disk_stack_limits or driver specific methods > > > (e.g. dm_table_set_restrictions) that are called _after_ all the limits > > > stacking occurs. > > > > > > By inverting the setting of the bdi's ra_pages and io_pages to be done > > > so early in __device_add_disk it'll break properly setting these values > > > for at least DM afaict. > > > > ra_pages never got inherited by stacking drivers, check it by modifying > > it on an underlying device and then creating a trivial dm or md one. > > Sure, not saying that it did. But if the goal is to set ra_pages based > on io_opt then to do that correctly on stacking drivers it must be done > in terms of limits stacking right? Or at least done at a location that > is after the limits stacking has occurred? So should DM just open-code > setting ra_pages like it did for io_pages? > > Because setting ra_pages in __device_add_disk() is way too early for DM > -- given it uses device_add_disk_no_queue_reg via add_disk_no_queue_reg > at DM device creation (before stacking all underlying devices' limits). I'll move it to blk_register_queue, which should work just fine.