From: Turritopsis Dohrnii Teo En Ming <ceo@teo-en-ming-corp.com>
To: dmaengine@vger.kernel.org
Subject: I discovered that UniFi USW-24P-250 POE network switch is based on Linux kernel 3.6.5
Date: Wed, 28 Jul 2021 22:07:55 +0800 [thread overview]
Message-ID: <0a9534bca5051fc844f1c42d683af085@teo-en-ming-corp.com> (raw)
Subject: I discovered that UniFi USW-24P-250 POE network switch is based
on Linux kernel 3.6.5
Good day from Singapore,
I discovered that UniFi USW-24P-250 POE network switch is based on Linux
kernel 3.6.5 and other open source software. I had an opportunity to
play with this UniFi USW-24P-250 POE network switch recently. The
console output and other information below shows that UniFi USW-24P-250
POE network switch is based on Linux kernel 3.6.5.
Please DO NOT try to configure UniFi network switches using the CLI. It
WILL NOT work. If you configure UniFi network switches using the CLI,
the IP address that you have manually configured will always go back to
192.168.1.20, which is the default IP address.
The only way to configure UniFi network switches is to connect them to a
network environment with DHCP server. You can then install and use UniFi
Controller to adopt the UniFi network switch. Configuring UniFi network
switches using UniFi Controller (GUI) is extremely easy and straight
forward. There is no need to use the CLI at all.
How to Configure UniFi USW-24P-250 POE Network Switch using CLI
===============================================================
Putty Settings
==============
Connection > Serial:
Speed(baud): 115200
Data bits: 8
Stop bits: 1
Parity: None
Flow control: None
Session:
Serial
Serial line: COM1
Speed: 115200
Default username and password to login to UniFi switch
======================================================
Default login: ubnt
Default password: ubnt
How to enter CLI of UniFi switch
================================
telnet localhost
enable
show run
===Begin of Default switch configuration===
!Current Configuration:
!
!System Description "USW-24P-250, 5.11.0.11599, Linux 3.6.5"
!System Software Version "5.11.0.11599"
!System Up Time "0 days 0 hrs 24 mins 4 secs"
!Additional Packages QOS,IPv6 Management
!
network parms 0.0.0.0 0.0.0.0 0.0.0.0
vlan database
exit
configure
line console
exit
line telnet
exit
spanning-tree mode rstp
!
no snmp-server community "public"
no snmp-server community "private"
set igmp reportforward lldp
set mld reportforward lldp
ip dhcp snooping
ip dhcp snooping vlan 1
cos-queue min-bandwidth 0 10 10 10 10 0 0 0
keepalive
interface 0/1
description 'Port 1'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/2
description 'Port 2'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/3
description 'Port 3'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/4
description 'Port 4'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/5
description 'Port 5'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/6
description 'Port 6'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/7
description 'Port 7'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/8
description 'Port 8'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/9
description 'Port 9'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/10
description 'Port 10'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/11
description 'Port 11'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/12
description 'Port 12'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/13
description 'Port 13'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/14
description 'Port 14'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/15
description 'Port 15'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/16
description 'Port 16'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/17
description 'Port 17'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/18
description 'Port 18'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/19
description 'Port 19'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/20
description 'Port 20'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/21
description 'Port 21'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/22
description 'Port 22'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/23
description 'Port 23'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/24
description 'Port 24'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/25
description 'Port 25'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface 0/26
description 'Port 26'
vlan ingressfilter
port-security max-dynamic 0
lldp transmit
lldp receive
lldp transmit-tlv port-desc
lldp transmit-tlv sys-name
lldp transmit-tlv sys-desc
lldp transmit-tlv sys-cap
lldp med
exit
interface lag 1
shutdown
no port-channel static
vlan participation exclude 1
exit
interface lag 2
shutdown
no port-channel static
vlan participation exclude 1
exit
interface lag 3
shutdown
no port-channel static
vlan participation exclude 1
exit
interface lag 4
shutdown
no port-channel static
vlan participation exclude 1
exit
interface lag 5
shutdown
no port-channel static
vlan participation exclude 1
exit
interface lag 6
shutdown
no port-channel static
vlan participation exclude 1
exit
no errdisable recovery cause mac-locking
no errdisable recovery cause denial-of-service
exit
===End of default switch configuration===
show network
Interface Status............................... Up
IP Address..................................... 0.0.0.0
Subnet Mask.................................... 0.0.0.0
Default Gateway................................ 0.0.0.0
IPv6 Administrative Mode....................... Enabled
IPv6 Prefix is ................................
fe80::f692:bfff:fe71:aac7/64
Burned In MAC Address.......................... F4:92:BF:71:AA:C7
Locally Administered MAC address............... 00:00:00:00:00:00
MAC Address Type............................... Burned In
Configured IPv4 Protocol....................... None
Configured IPv6 Protocol....................... None
IPv6 AutoConfig Mode........................... Enabled
Management VLAN ID............................. 1
Reference Guide: Getting into the CLI for a Unifi switch
Link:
https://dan.langille.org/2018/01/12/getting-into-the-cli-for-a-unifi-switch/
Reference Guide: Ubiquiti Networks EdgeSwitch CLI Command Reference
Link:
https://www.doubleradius.com/site/stores/ubiquiti/Ubiquiti-Edgeswitch-CLI-Command-Reference-Quick-Start-Guide.pdf
Configure the management interface of UniFi switch
==================================================
hostname UniFi-USW-24P-250-Switch
network parms 192.168.0.6 255.255.255.0 192.168.0.2
(UniFi-USW-24P-250-Switch) #show network
Interface Status............................... Up
IP Address..................................... 192.168.0.6
Subnet Mask.................................... 255.255.255.0
Default Gateway................................ 192.168.0.2
IPv6 Administrative Mode....................... Enabled
IPv6 Prefix is ................................
fe80::f692:bfff:fe71:aac7/64
Burned In MAC Address.......................... F4:92:BF:71:AA:C7
Locally Administered MAC address............... 00:00:00:00:00:00
MAC Address Type............................... Burned In
Configured IPv4 Protocol....................... None
Configured IPv6 Protocol....................... None
IPv6 AutoConfig Mode........................... Enabled
Management VLAN ID............................. 1
configure
username admin level 15 password
Enter new password:****************
Confirm new password:****************
write memory
This operation may take a few minutes.
Management interfaces will not be available during this time.
Are you sure you want to save? (y/n) y
Config file 'startup-config' created successfully .
Configuration Saved!
UBNT-US.v5.11.0# reboot now
UBNT-US.v5.11.0# + exec
umount: can't remount rootfs read-only
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to[ 991.180000] Disabling non-boot CPUs ...
[ 991.180000] Restarting system.
U-Boot usw-v1.1.4.115-g14af1ee6 (Feb 14 2017 - 18:50:54)
DEV ID= 0000db56
SKU ID = 0x8344
DDR type: DDR3
MEMC 0 DDR speed = 667MHz
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DDR Tune Completed
DRAM: 256 MiB
WARNING: Caches not enabled
soc_pcie_hw_init : port->reg_base = 0x18012000 , its value = 0x1
PCIe port 0 in RC mode
pos is 172
==>PCIE: LINKSTA reg 0xbe val 0x1001
**************
port 0 is not active!!
**************
In: serial
Out: serial
Err: serial
Unlocking L2 Cache ...Done
arm_clk=400MHz, axi_clk=200MHz, apb_clk=50MHz, arm_periph_clk=200MHz
Disabling outer cache
Net: Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
ubnt_bootsel_init: bootsel magic=a34de82b, bootsel = 0
UBNT application initialized
Boot partition selected = 0
Loading Kernel Image @ 1000000, size = 15728640
Verifying 'kernel0' parition:OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Ubiquiti 5.11.0.11599
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 15068480 Bytes = 14.4 MiB
Load Address: 00018000
Entry Point: 00018000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
boot_prep_linux commandline: console=ttyS0,115200 mem=128M@0x0
mem=128M@0x68000000
mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0),15424k(kernel1),1024k(cfg),64k(EEPROM)
ubntbootid=0
Starting kernel ...
Disabling outer cache
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.6.5 (builder@link-owrt1505-builder) (gcc
version 4.7.2 (OpenWrt GCC 4.7.2 unknown) ) #2 SMP Wed Apr 22 10:09:32
MDT 2020
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7),
cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine: Broadcom iProc
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] BUG: mapping for 0x18000000 at 0xf0000000 out of vmalloc
space
[ 0.000000] BUG: mapping for 0x19000000 at 0xf1000000 out of vmalloc
space
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1caf000 s6272 r8192 d14208
u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 61952
[ 0.000000] Kernel command line: console=ttyS0,115200 mem=128M@0x0
mem=128M@0x68000000
mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0),15424k(kernel1),1024k(cfg),64k(EEPROM)
ubntbootid=0 ubootver=usw-v1.1.4.115-g14af1ee6
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Memory: 128MB 128MB = 256MB total
[ 0.000000] Memory: 244992k/244992k available, 17152k reserved,
131072K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xf0000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0018000 - 0xc034d7f8 (3286 kB)
[ 0.000000] .init : 0xc034e000 - 0xc0e4c880 (11259 kB)
[ 0.000000] .data : 0xc0e4e000 - 0xc0e76d40 ( 164 kB)
[ 0.000000] .bss : 0xc0e76d64 - 0xc0ea5354 ( 186 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:292
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns,
wraps every 4294967286ms
[ 0.010000] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[ 0.050000] pid_max: default: 4096 minimum: 301
[ 0.050000] Mount-cache hash table entries: 512
[ 0.050000] CPU: Testing write buffer coherency: ok
[ 0.050000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.050000] Setting up static identity map for 0x282350 - 0x2823a8
[ 0.050000] L310 cache controller enabled
[ 0.050000] l2x0: 8 ways, CACHE_ID 0x410000c9, AUX_CTRL 0x0a120000,
Cache size: 131072 B
[ 0.050000] Brought up 1 CPUs
[ 0.050000] SMP: Total of 1 processors activated (795.44 BogoMIPS).
[ 0.050000] devtmpfs: initialized
[ 0.060000] NET: Registered protocol family 16
[ 0.060000] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.060000] GENPLL[5] mdiv=40 rate=2000000000
[ 0.060000] Sel=1 Ovr=1 Div=48
[ 0.060000] UART clock rate 50000000
[ 0.080000] bio: create slab <bio-0> at 0
[ 0.080000] Bluetooth: Core ver 2.16
[ 0.080000] NET: Registered protocol family 31
[ 0.080000] Bluetooth: HCI device and connection manager initialized
[ 0.080000] Bluetooth: HCI socket layer initialized
[ 0.080000] Bluetooth: L2CAP socket layer initialized
[ 0.080000] Bluetooth: SCO socket layer initialized
[ 0.080000] Switching to clocksource iproc_gtimer
[ 0.090000] NET: Registered protocol family 2
[ 0.090000] TCP established hash table entries: 4096 (order: 3, 32768
bytes)
[ 0.090000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.090000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.090000] TCP: reno registered
[ 0.090000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.090000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.090000] NET: Registered protocol family 1
[ 14.360000] pm_init: Initializing Power Management ....
[ 14.360000] iproc gpiochip add GPIOA
[ 14.360000] GPIOA:ioaddr f0000060
[ 14.360000] GPIOA:intr_ioaddr f0000000 dmu_ioaddr (null)
[ 14.610000] PCIE0: LINKSTA reg 0xbe val 0x1001
[ 14.610000] reg[0xac]=0x10, reg[0xae]=0x42, reg[0xb0]=0x8000,
reg[0xb4]=0x2c10, reg[0xb6]=0x10, reg[0xb8]=0x5c12, reg[0xba]=0x65,
reg[0xbe]=0x1001, reg[0xc6]=0x40, reg[0xca]=0x1, reg[0xd0]=0x1f,
reg[0xd2]=0x8, reg[0xdc]=0x1, PCIE0 link=0
[ 14.860000] PCIe port 1 in End-Point mode - ignored
[ 14.860000] Registering iproc_pmu_device
[ 14.860000] bounce pool size: 64 pages
[ 14.880000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 14.880000] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 14.880000] msgmni has been set to 222
[ 14.880000] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 254)
[ 14.880000] io scheduler noop registered
[ 14.880000] io scheduler deadline registered (default)
[ 14.880000] io scheduler cfq registered
[ 14.880000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 14.890000] serial8250.0: ttyS0 at MMIO 0x18000400 (irq = 123) is a
16550A
[ 15.360000] console [ttyS0] enabled
[ 15.370000] serial8250.0: ttyS1 at MMIO 0x18000300 (irq = 123) is a
16550A
[ 15.400000] brd: module loaded
[ 15.410000] loop: module loaded
[ 15.420000] nbd: registered device at major 43
[ 15.440000] tun: Universal TUN/TAP device driver, 1.6
[ 15.450000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 15.450000] Bluetooth: HCI UART driver ver 2.2
[ 15.460000] Bluetooth: HCI H4 protocol initialized
[ 15.460000] Bluetooth: HCI BCSP protocol initialized
[ 15.470000] TCP: cubic registered
[ 15.470000] NET: Registered protocol family 10
[ 15.480000] sit: IPv6 over IPv4 tunneling driver
[ 15.490000] NET: Registered protocol family 17
[ 15.490000] Bluetooth: RFCOMM TTY layer initialized
[ 15.500000] Bluetooth: RFCOMM socket layer initialized
[ 15.500000] Bluetooth: RFCOMM ver 1.11
[ 15.510000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.510000] Bluetooth: BNEP filters: protocol multicast
[ 15.520000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 15.520000] 8021q: 802.1Q VLAN Support v1.8
[ 15.530000] GENPLL[5] mdiv=40 rate=2000000000
[ 15.530000] qspi_iproc qspi_iproc.1: 1-lane output, 3-byte address
[ 15.540000] m25p80 spi1.0: found mx25l25635e, expected m25p80
[ 15.550000] m25p80 spi1.0: mx25l25635e (32768 Kbytes)
[ 15.550000] 7 cmdlinepart partitions found on MTD device spi1.0
[ 15.560000] Creating 7 MTD partitions on "spi1.0":
[ 15.560000] 0x000000000000-0x0000000c0000 : "u-boot"
[ 15.570000] 0x0000000c0000-0x0000000d0000 : "u-boot-env"
[ 15.580000] 0x0000000d0000-0x0000000e0000 : "shmoo"
[ 15.580000] 0x0000000e0000-0x000000fe0000 : "kernel0"
[ 15.590000] 0x000000fe0000-0x000001ef0000 : "kernel1"
[ 15.600000] 0x000001ef0000-0x000001ff0000 : "cfg"
[ 15.610000] 0x000001ff0000-0x000002000000 : "EEPROM"
[ 15.640000] Freeing init memory: 11256K
[ 15.700000] ubnt_common: module license 'Proprietary' taints kernel.
[ 15.710000] Disabling lock debugging due to kernel taint
[ 15.780000] Data abort at addr=0xc8a10224, fsr=0x1406 ignored.
[ 15.790000] Data abort at addr=0xc8a10224, fsr=0x1406 ignored.
[ 15.810000] gpiodev: reset_timeout=3
Could not find cfg type: 1
Could not find cfg type: 2
...running /sbin/init
init started: BusyBox v1.23.2 (2020-04-22 10:04:15 MDT)
+ exec
Restoring EEPROM data from ubnthal
MAC: f4:92:bf:71:aa:c7
Validating the active image /dev/mtd3..."5.11.0.11599"
Validating the backup image /dev/mtd4..."5.11.0.11599"
DMA pool size: 4194304
AXI unit 0: Dev 0x8344, Rev 0x01, Chip BCM53344_A0, Driver BCM56150_A0
SOC unit 0 attached to PCI device BCM53344_A0
(Unit 1)>
Applying Global configuration, please wait ...
Applying Interface configuration, please wait ...
Please press Enter to activate this console. inform sent
inform sent
inform sent
Using the UniFi Controller to adopt the UniFi Switch
=====================================================
192.168.0.10 is the UniFi Controller on the management laptop.
UBNT-US.v5.11.0# set-inform http://192.168.0.10:8080/inform
Adoption request sent to 'http://192.168.0.10:8080/inform'. Use the
controller to complete the adopt process.
telnet localhost
enable
network parms 192.168.0.6 255.255.255.0 192.168.0.2
UBNT-US.v5.11.0# info
Model: USW-24P-250
Version: 5.11.0.11599
MAC Address: f4:92:bf:71:aa:c7
IP Address: 192.168.1.20
Hostname: UBNT
Uptime: 7868 seconds
Status: Connected (http://192.168.0.10:8080/inform)
Mr. Turritopsis Dohrnii Teo En Ming, 43 years old as of 28 July 2021, is
a TARGETED INDIVIDUAL living in Singapore. He is an IT Consultant with a
System Integrator (SI)/computer firm in Singapore. He is an IT
enthusiast.
--
-----BEGIN EMAIL SIGNATURE-----
The Gospel for all Targeted Individuals (TIs):
[The New York Times] Microwave Weapons Are Prime Suspect in Ills of
U.S. Embassy Workers
Link:
https://www.nytimes.com/2018/09/01/science/sonic-attack-cuba-microwave.html
********************************************************************************************
Singaporean Targeted Individual Mr. Turritopsis Dohrnii Teo En Ming's
Academic Qualifications as at 14 Feb 2019 and refugee seeking attempts
at the United Nations Refugee Agency Bangkok (21 Mar 2017), in Taiwan
(5 Aug 2019) and Australia (25 Dec 2019 to 9 Jan 2020):
[1] https://tdtemcerts.wordpress.com/
[2] https://tdtemcerts.blogspot.sg/
[3] https://www.scribd.com/user/270125049/Teo-En-Ming
-----END EMAIL SIGNATURE-----
reply other threads:[~2021-07-28 14:15 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0a9534bca5051fc844f1c42d683af085@teo-en-ming-corp.com \
--to=ceo@teo-en-ming-corp.com \
--cc=dmaengine@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).