From: Robin Gong <yibin.gong@nxp.com>
To: mark.rutland@arm.com, broonie@kernel.org, robh+dt@kernel.org,
catalin.marinas@arm.com, vkoul@kernel.org, will.deacon@arm.com,
shawnguo@kernel.org, festevam@gmail.com, s.hauer@pengutronix.de,
martin.fuzzey@flowbird.group, u.kleine-koenig@pengutronix.de,
dan.j.williams@intel.com, matthias.schiffer@ew.tq-group.com
Cc: linux-spi@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
kernel@pengutronix.de, linux-imx@nxp.com,
dmaengine@vger.kernel.org
Subject: [PATCH v9 09/14] spi: imx: remove ERR009165 workaround on i.mx6ul
Date: Sat, 6 Jun 2020 05:32:30 +0800 [thread overview]
Message-ID: <1591392755-19136-10-git-send-email-yibin.gong@nxp.com> (raw)
In-Reply-To: <1591392755-19136-1-git-send-email-yibin.gong@nxp.com>
ERR009165 fixed on i.mx6ul/6ull/6sll. All other i.mx6/7 and
i.mx8m/8mm still need this errata. Please refer to nxp official
errata document from https://www.nxp.com/ .
For removing workaround on those chips. Add new i.mx6ul type.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Mark Brown <broonie@kernel.org>
---
drivers/spi/spi-imx.c | 59 ++++++++++++++++++++++++++++++++++++++++++++++-----
1 file changed, 54 insertions(+), 5 deletions(-)
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index f82d63f..9067c95 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -57,6 +57,7 @@ enum spi_imx_devtype {
IMX35_CSPI, /* CSPI on all i.mx except above */
IMX51_ECSPI, /* ECSPI on i.mx51 */
IMX53_ECSPI, /* ECSPI on i.mx53 and later */
+ IMX6UL_ECSPI, /* ERR009165 fix from i.mx6ul */
};
struct spi_imx_data;
@@ -76,6 +77,11 @@ struct spi_imx_devtype_data {
bool has_slavemode;
unsigned int fifo_size;
bool dynamic_burst;
+ /*
+ * ERR009165 fixed or not:
+ * https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
+ */
+ bool tx_glitch_fixed;
enum spi_imx_devtype devtype;
};
@@ -132,6 +138,11 @@ static inline int is_imx51_ecspi(struct spi_imx_data *d)
return d->devtype_data->devtype == IMX51_ECSPI;
}
+static inline int is_imx6ul_ecspi(struct spi_imx_data *d)
+{
+ return d->devtype_data->devtype == IMX6UL_ECSPI;
+}
+
static inline int is_imx53_ecspi(struct spi_imx_data *d)
{
return d->devtype_data->devtype == IMX53_ECSPI;
@@ -591,8 +602,14 @@ static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
ctrl |= mx51_ecspi_clkdiv(spi_imx, t->speed_hz, &clk);
spi_imx->spi_bus_clk = clk;
- /* ERR009165: work in XHC mode as PIO */
- ctrl &= ~MX51_ECSPI_CTRL_SMC;
+ /*
+ * ERR009165: work in XHC mode instead of SMC as PIO on the chips
+ * before i.mx6ul.
+ */
+ if (spi_imx->usedma && spi_imx->devtype_data->tx_glitch_fixed)
+ ctrl |= MX51_ECSPI_CTRL_SMC;
+ else
+ ctrl &= ~MX51_ECSPI_CTRL_SMC;
writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
@@ -618,12 +635,16 @@ static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
static void mx51_setup_wml(struct spi_imx_data *spi_imx)
{
+ u32 tx_wml = 0;
+
+ if (spi_imx->devtype_data->tx_glitch_fixed)
+ tx_wml = spi_imx->wml;
/*
* Configure the DMA register: setup the watermark
* and enable DMA request.
*/
writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml - 1) |
- MX51_ECSPI_DMA_TX_WML(0) |
+ MX51_ECSPI_DMA_TX_WML(tx_wml) |
MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN |
MX51_ECSPI_DMA_RXTDEN, spi_imx->base + MX51_ECSPI_DMA);
@@ -1017,6 +1038,23 @@ static struct spi_imx_devtype_data imx53_ecspi_devtype_data = {
.devtype = IMX53_ECSPI,
};
+static struct spi_imx_devtype_data imx6ul_ecspi_devtype_data = {
+ .intctrl = mx51_ecspi_intctrl,
+ .prepare_message = mx51_ecspi_prepare_message,
+ .prepare_transfer = mx51_ecspi_prepare_transfer,
+ .trigger = mx51_ecspi_trigger,
+ .rx_available = mx51_ecspi_rx_available,
+ .reset = mx51_ecspi_reset,
+ .setup_wml = mx51_setup_wml,
+ .fifo_size = 64,
+ .has_dmamode = true,
+ .dynamic_burst = true,
+ .has_slavemode = true,
+ .tx_glitch_fixed = true,
+ .disable = mx51_ecspi_disable,
+ .devtype = IMX6UL_ECSPI,
+};
+
static const struct platform_device_id spi_imx_devtype[] = {
{
.name = "imx1-cspi",
@@ -1040,6 +1078,9 @@ static const struct platform_device_id spi_imx_devtype[] = {
.name = "imx53-ecspi",
.driver_data = (kernel_ulong_t) &imx53_ecspi_devtype_data,
}, {
+ .name = "imx6ul-ecspi",
+ .driver_data = (kernel_ulong_t) &imx6ul_ecspi_devtype_data,
+ }, {
/* sentinel */
}
};
@@ -1052,6 +1093,7 @@ static const struct of_device_id spi_imx_dt_ids[] = {
{ .compatible = "fsl,imx35-cspi", .data = &imx35_cspi_devtype_data, },
{ .compatible = "fsl,imx51-ecspi", .data = &imx51_ecspi_devtype_data, },
{ .compatible = "fsl,imx53-ecspi", .data = &imx53_ecspi_devtype_data, },
+ { .compatible = "fsl,imx6ul-ecspi", .data = &imx6ul_ecspi_devtype_data, },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, spi_imx_dt_ids);
@@ -1179,7 +1221,14 @@ static int spi_imx_dma_configure(struct spi_master *master)
tx.direction = DMA_MEM_TO_DEV;
tx.dst_addr = spi_imx->base_phys + MXC_CSPITXDATA;
tx.dst_addr_width = buswidth;
- tx.dst_maxburst = spi_imx->wml;
+ /*
+ * For ERR009165 with TX_THRESHOLD=0 could enlarge burst size to fifo
+ * size to speed up fifo filling as possible.
+ */
+ if (spi_imx->devtype_data->tx_glitch_fixed)
+ tx.dst_maxburst = spi_imx->wml;
+ else
+ tx.dst_maxburst = spi_imx->devtype_data->fifo_size;
ret = dmaengine_slave_config(master->dma_tx, &tx);
if (ret) {
dev_err(spi_imx->dev, "TX dma configuration failed with %d\n", ret);
@@ -1690,7 +1739,7 @@ static int spi_imx_probe(struct platform_device *pdev)
spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
| SPI_NO_CS;
if (is_imx35_cspi(spi_imx) || is_imx51_ecspi(spi_imx) ||
- is_imx53_ecspi(spi_imx))
+ is_imx53_ecspi(spi_imx) || is_imx6ul_ecspi(spi_imx))
spi_imx->bitbang.master->mode_bits |= SPI_LOOP | SPI_READY;
spi_imx->spi_drctl = spi_drctl;
--
2.7.4
next prev parent reply other threads:[~2020-06-05 13:33 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-05 21:32 [PATCH v9 00/14] add ecspi ERR009165 for i.mx6/7 soc family Robin Gong
2020-06-05 21:32 ` [PATCH v9 01/14] Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core" Robin Gong
2020-06-05 21:32 ` [PATCH v9 02/14] Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores" Robin Gong
2020-06-05 21:32 ` [PATCH v9 03/14] Revert "dmaengine: imx-sdma: refine to load context only once" Robin Gong
2020-06-05 21:32 ` [PATCH v9 04/14] dmaengine: imx-sdma: remove duplicated sdma_load_context Robin Gong
2020-06-05 21:32 ` [PATCH v9 05/14] spi: imx: fallback to PIO if dma setup failure Robin Gong
2020-06-05 15:01 ` Mark Brown
2020-06-05 21:32 ` [PATCH v9 06/14] spi: imx: add dma_sync_sg_for_device after fallback from dma Robin Gong
2020-06-05 21:32 ` [PATCH v9 07/14] dmaengine: imx-sdma: add mcu_2_ecspi script Robin Gong
2020-06-05 21:32 ` [PATCH v9 08/14] spi: imx: fix ERR009165 Robin Gong
2020-06-05 21:32 ` Robin Gong [this message]
2020-06-05 21:32 ` [PATCH v9 10/14] spi: imx: add new i.mx6ul compatible name in binding doc Robin Gong
2020-06-05 21:32 ` [PATCH v9 11/14] dmaengine: imx-sdma: remove ERR009165 on i.mx6ul Robin Gong
2020-06-05 21:32 ` [PATCH v9 12/14] dma: imx-sdma: add i.mx6ul compatible name Robin Gong
2020-06-05 21:32 ` [PATCH v9 13/14] dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm Robin Gong
2020-06-05 21:32 ` [PATCH v9 14/14] dmaengine: imx-sdma: add uart rom script Robin Gong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1591392755-19136-10-git-send-email-yibin.gong@nxp.com \
--to=yibin.gong@nxp.com \
--cc=broonie@kernel.org \
--cc=catalin.marinas@arm.com \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=martin.fuzzey@flowbird.group \
--cc=matthias.schiffer@ew.tq-group.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=u.kleine-koenig@pengutronix.de \
--cc=vkoul@kernel.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).