[PATCH v3 0/7] Allwinner H6 DMA support

[PATCH v3 0/7] Allwinner H6 DMA support

[Clément Péron]

Hi,

This series has been first proposed by Jernej Skrabec[1].
As this series is mandatory for SPDIF/I2S support and because he is
busy on Cedrus stuff. I asked him to make the minor change requested
and repost it.
Authorship remains to him.

I have tested this series with SPDIF driver and added a patch to enable
DMA_SUN6I_CONFIG for arm64.

Original Post:
"
DMA engine engine on H6 almost the same as on older SoCs. The biggest
difference is that it has slightly rearranged bits in registers and
it needs additional clock, probably due to iommu.

These patches were tested with I2S connected to HDMI. I2S needs
additional patches which will be sent later.

Please take a look.

Best regards,
Jernej
"

Thanks,
Clément

Changes since v2:
 - Drop the change of "dma-request" default value

Changes since v1:
 - Enable DMA_SUN6I in arm64 defconfig
 - Change mbus_clk to has_mbus_clk
 - Collect Rob H. reviewed-by

Clément Péron (1):
  arm64: defconfig: enable Allwinner DMA drivers

Jernej Skrabec (6):
  dt-bindings: arm64: allwinner: h6: Add binding for DMA controller
  dmaengine: sun6i: Add a quirk for additional mbus clock
  dmaengine: sun6i: Add a quirk for setting DRQ fields
  dmaengine: sun6i: Add a quirk for setting mode fields
  dmaengine: sun6i: Add support for H6 DMA
  arm64: dts: allwinner: h6: Add DMA node

 .../devicetree/bindings/dma/sun6i-dma.txt     |   9 +-
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  |  12 ++
 arch/arm64/configs/defconfig                  |   1 +
 drivers/dma/sun6i-dma.c                       | 147 +++++++++++++-----
 4 files changed, 132 insertions(+), 37 deletions(-)

-- 
2.20.1

[PATCH v3 1/7] dt-bindings: arm64: allwinner: h6: Add binding for DMA controller

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

DMA in H6 is similar to other DMA controller, except it is first which
supports more than 32 request sources and has 16 channels. It also needs
additional clock to be enabled.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 Documentation/devicetree/bindings/dma/sun6i-dma.txt | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
index 7fccc20d8331..cae31f4e77ba 100644
--- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt
+++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
@@ -28,12 +28,17 @@ Example:
 	};
 
 ------------------------------------------------------------------------------
-For A64 DMA controller:
+For A64 and H6 DMA controller:
 
 Required properties:
-- compatible:	"allwinner,sun50i-a64-dma"
+- compatible:	Must be one of
+		  "allwinner,sun50i-a64-dma"
+		  "allwinner,sun50i-h6-dma"
 - dma-channels: Number of DMA channels supported by the controller.
 		Refer to Documentation/devicetree/bindings/dma/dma.txt
+- clocks:	In addition to parent AHB clock, it should also contain mbus
+		clock (H6 only)
+- clock-names:	Should contain "bus" and "mbus" (H6 only)
 - all properties above, i.e. reg, interrupts, clocks, resets and #dma-cells
 
 Optional properties:
-- 
2.20.1

[PATCH v3 2/7] dmaengine: sun6i: Add a quirk for additional mbus clock

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 DMA controller needs additional mbus clock to be enabled.

Add a quirk for it and handle it accordingly.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/dma/sun6i-dma.c | 23 ++++++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
index 0cd13f17fc11..7d9606997251 100644
--- a/drivers/dma/sun6i-dma.c
+++ b/drivers/dma/sun6i-dma.c
@@ -129,6 +129,7 @@ struct sun6i_dma_config {
 	u32 dst_burst_lengths;
 	u32 src_addr_widths;
 	u32 dst_addr_widths;
+	bool has_mbus_clk;
 };
 
 /*
@@ -182,6 +183,7 @@ struct sun6i_dma_dev {
 	struct dma_device	slave;
 	void __iomem		*base;
 	struct clk		*clk;
+	struct clk		*clk_mbus;
 	int			irq;
 	spinlock_t		lock;
 	struct reset_control	*rstc;
@@ -1208,6 +1210,14 @@ static int sun6i_dma_probe(struct platform_device *pdev)
 		return PTR_ERR(sdc->clk);
 	}
 
+	if (sdc->cfg->has_mbus_clk) {
+		sdc->clk_mbus = devm_clk_get(&pdev->dev, "mbus");
+		if (IS_ERR(sdc->clk_mbus)) {
+			dev_err(&pdev->dev, "No mbus clock specified\n");
+			return PTR_ERR(sdc->clk_mbus);
+		}
+	}
+
 	sdc->rstc = devm_reset_control_get(&pdev->dev, NULL);
 	if (IS_ERR(sdc->rstc)) {
 		dev_err(&pdev->dev, "No reset controller specified\n");
@@ -1312,11 +1322,19 @@ static int sun6i_dma_probe(struct platform_device *pdev)
 		goto err_reset_assert;
 	}
 
+	if (sdc->cfg->has_mbus_clk) {
+		ret = clk_prepare_enable(sdc->clk_mbus);
+		if (ret) {
+			dev_err(&pdev->dev, "Couldn't enable mbus clock\n");
+			goto err_clk_disable;
+		}
+	}
+
 	ret = devm_request_irq(&pdev->dev, sdc->irq, sun6i_dma_interrupt, 0,
 			       dev_name(&pdev->dev), sdc);
 	if (ret) {
 		dev_err(&pdev->dev, "Cannot request IRQ\n");
-		goto err_clk_disable;
+		goto err_mbus_clk_disable;
 	}
 
 	ret = dma_async_device_register(&sdc->slave);
@@ -1341,6 +1359,8 @@ static int sun6i_dma_probe(struct platform_device *pdev)
 	dma_async_device_unregister(&sdc->slave);
 err_irq_disable:
 	sun6i_kill_tasklet(sdc);
+err_mbus_clk_disable:
+	clk_disable_unprepare(sdc->clk_mbus);
 err_clk_disable:
 	clk_disable_unprepare(sdc->clk);
 err_reset_assert:
@@ -1359,6 +1379,7 @@ static int sun6i_dma_remove(struct platform_device *pdev)
 
 	sun6i_kill_tasklet(sdc);
 
+	clk_disable_unprepare(sdc->clk_mbus);
 	clk_disable_unprepare(sdc->clk);
 	reset_control_assert(sdc->rstc);
 
-- 
2.20.1

[PATCH v3 3/7] dmaengine: sun6i: Add a quirk for setting DRQ fields

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 DMA has more than 32 possible DRQs. That means that current maximum
of 31 DRQs is not enough anymore.

Add a quirk which will set source and destination DRQ number.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/dma/sun6i-dma.c | 48 ++++++++++++++++++++++++-----------------
 1 file changed, 28 insertions(+), 20 deletions(-)

diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
index 7d9606997251..f725b93fd21a 100644
--- a/drivers/dma/sun6i-dma.c
+++ b/drivers/dma/sun6i-dma.c
@@ -68,15 +68,15 @@
 #define DMA_CHAN_LLI_ADDR	0x08
 
 #define DMA_CHAN_CUR_CFG	0x0c
-#define DMA_CHAN_MAX_DRQ		0x1f
-#define DMA_CHAN_CFG_SRC_DRQ(x)		((x) & DMA_CHAN_MAX_DRQ)
+#define DMA_CHAN_MAX_DRQ_A31		0x1f
+#define DMA_CHAN_CFG_SRC_DRQ_A31(x)	((x) & DMA_CHAN_MAX_DRQ_A31)
 #define DMA_CHAN_CFG_SRC_IO_MODE	BIT(5)
 #define DMA_CHAN_CFG_SRC_LINEAR_MODE	(0 << 5)
 #define DMA_CHAN_CFG_SRC_BURST_A31(x)	(((x) & 0x3) << 7)
 #define DMA_CHAN_CFG_SRC_BURST_H3(x)	(((x) & 0x3) << 6)
 #define DMA_CHAN_CFG_SRC_WIDTH(x)	(((x) & 0x3) << 9)
 
-#define DMA_CHAN_CFG_DST_DRQ(x)		(DMA_CHAN_CFG_SRC_DRQ(x) << 16)
+#define DMA_CHAN_CFG_DST_DRQ_A31(x)	(DMA_CHAN_CFG_SRC_DRQ_A31(x) << 16)
 #define DMA_CHAN_CFG_DST_IO_MODE	(DMA_CHAN_CFG_SRC_IO_MODE << 16)
 #define DMA_CHAN_CFG_DST_LINEAR_MODE	(DMA_CHAN_CFG_SRC_LINEAR_MODE << 16)
 #define DMA_CHAN_CFG_DST_BURST_A31(x)	(DMA_CHAN_CFG_SRC_BURST_A31(x) << 16)
@@ -125,6 +125,7 @@ struct sun6i_dma_config {
 	 */
 	void (*clock_autogate_enable)(struct sun6i_dma_dev *);
 	void (*set_burst_length)(u32 *p_cfg, s8 src_burst, s8 dst_burst);
+	void (*set_drq)(u32 *p_cfg, s8 src_drq, s8 dst_drq);
 	u32 src_burst_lengths;
 	u32 dst_burst_lengths;
 	u32 src_addr_widths;
@@ -311,6 +312,12 @@ static void sun6i_set_burst_length_h3(u32 *p_cfg, s8 src_burst, s8 dst_burst)
 		  DMA_CHAN_CFG_DST_BURST_H3(dst_burst);
 }
 
+static void sun6i_set_drq_a31(u32 *p_cfg, s8 src_drq, s8 dst_drq)
+{
+	*p_cfg |= DMA_CHAN_CFG_SRC_DRQ_A31(src_drq) |
+		  DMA_CHAN_CFG_DST_DRQ_A31(dst_drq);
+}
+
 static size_t sun6i_get_chan_size(struct sun6i_pchan *pchan)
 {
 	struct sun6i_desc *txd = pchan->desc;
@@ -634,14 +641,13 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_dma_memcpy(
 
 	burst = convert_burst(8);
 	width = convert_buswidth(DMA_SLAVE_BUSWIDTH_4_BYTES);
-	v_lli->cfg = DMA_CHAN_CFG_SRC_DRQ(DRQ_SDRAM) |
-		DMA_CHAN_CFG_DST_DRQ(DRQ_SDRAM) |
-		DMA_CHAN_CFG_DST_LINEAR_MODE |
+	v_lli->cfg = DMA_CHAN_CFG_DST_LINEAR_MODE |
 		DMA_CHAN_CFG_SRC_LINEAR_MODE |
 		DMA_CHAN_CFG_SRC_WIDTH(width) |
 		DMA_CHAN_CFG_DST_WIDTH(width);
 
 	sdev->cfg->set_burst_length(&v_lli->cfg, burst, burst);
+	sdev->cfg->set_drq(&v_lli->cfg, DRQ_SDRAM, DRQ_SDRAM);
 
 	sun6i_dma_lli_add(NULL, v_lli, p_lli, txd);
 
@@ -695,9 +701,8 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 			v_lli->dst = sconfig->dst_addr;
 			v_lli->cfg = lli_cfg |
 				DMA_CHAN_CFG_DST_IO_MODE |
-				DMA_CHAN_CFG_SRC_LINEAR_MODE |
-				DMA_CHAN_CFG_SRC_DRQ(DRQ_SDRAM) |
-				DMA_CHAN_CFG_DST_DRQ(vchan->port);
+				DMA_CHAN_CFG_SRC_LINEAR_MODE;
+			sdev->cfg->set_drq(&v_lli->cfg, DRQ_SDRAM, vchan->port);
 
 			dev_dbg(chan2dev(chan),
 				"%s; chan: %d, dest: %pad, src: %pad, len: %u. flags: 0x%08lx\n",
@@ -710,9 +715,8 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 			v_lli->dst = sg_dma_address(sg);
 			v_lli->cfg = lli_cfg |
 				DMA_CHAN_CFG_DST_LINEAR_MODE |
-				DMA_CHAN_CFG_SRC_IO_MODE |
-				DMA_CHAN_CFG_DST_DRQ(DRQ_SDRAM) |
-				DMA_CHAN_CFG_SRC_DRQ(vchan->port);
+				DMA_CHAN_CFG_SRC_IO_MODE;
+			sdev->cfg->set_drq(&v_lli->cfg, vchan->port, DRQ_SDRAM);
 
 			dev_dbg(chan2dev(chan),
 				"%s; chan: %d, dest: %pad, src: %pad, len: %u. flags: 0x%08lx\n",
@@ -780,17 +784,15 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_dma_cyclic(
 			v_lli->dst = sconfig->dst_addr;
 			v_lli->cfg = lli_cfg |
 				DMA_CHAN_CFG_DST_IO_MODE |
-				DMA_CHAN_CFG_SRC_LINEAR_MODE |
-				DMA_CHAN_CFG_SRC_DRQ(DRQ_SDRAM) |
-				DMA_CHAN_CFG_DST_DRQ(vchan->port);
+				DMA_CHAN_CFG_SRC_LINEAR_MODE;
+			sdev->cfg->set_drq(&v_lli->cfg, DRQ_SDRAM, vchan->port);
 		} else {
 			v_lli->src = sconfig->src_addr;
 			v_lli->dst = buf_addr + period_len * i;
 			v_lli->cfg = lli_cfg |
 				DMA_CHAN_CFG_DST_LINEAR_MODE |
-				DMA_CHAN_CFG_SRC_IO_MODE |
-				DMA_CHAN_CFG_DST_DRQ(DRQ_SDRAM) |
-				DMA_CHAN_CFG_SRC_DRQ(vchan->port);
+				DMA_CHAN_CFG_SRC_IO_MODE;
+			sdev->cfg->set_drq(&v_lli->cfg, vchan->port, DRQ_SDRAM);
 		}
 
 		prev = sun6i_dma_lli_add(prev, v_lli, p_lli, txd);
@@ -1055,6 +1057,7 @@ static struct sun6i_dma_config sun6i_a31_dma_cfg = {
 	.nr_max_requests = 30,
 	.nr_max_vchans   = 53,
 	.set_burst_length = sun6i_set_burst_length_a31,
+	.set_drq          = sun6i_set_drq_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1076,6 +1079,7 @@ static struct sun6i_dma_config sun8i_a23_dma_cfg = {
 	.nr_max_vchans   = 37,
 	.clock_autogate_enable = sun6i_enable_clock_autogate_a23,
 	.set_burst_length = sun6i_set_burst_length_a31,
+	.set_drq          = sun6i_set_drq_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1092,6 +1096,7 @@ static struct sun6i_dma_config sun8i_a83t_dma_cfg = {
 	.nr_max_vchans   = 39,
 	.clock_autogate_enable = sun6i_enable_clock_autogate_a23,
 	.set_burst_length = sun6i_set_burst_length_a31,
+	.set_drq          = sun6i_set_drq_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1115,6 +1120,7 @@ static struct sun6i_dma_config sun8i_h3_dma_cfg = {
 	.nr_max_vchans   = 34,
 	.clock_autogate_enable = sun6i_enable_clock_autogate_h3,
 	.set_burst_length = sun6i_set_burst_length_h3,
+	.set_drq          = sun6i_set_drq_a31,
 	.src_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.dst_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1134,6 +1140,7 @@ static struct sun6i_dma_config sun8i_h3_dma_cfg = {
 static struct sun6i_dma_config sun50i_a64_dma_cfg = {
 	.clock_autogate_enable = sun6i_enable_clock_autogate_h3,
 	.set_burst_length = sun6i_set_burst_length_h3,
+	.set_drq          = sun6i_set_drq_a31,
 	.src_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.dst_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1157,6 +1164,7 @@ static struct sun6i_dma_config sun8i_v3s_dma_cfg = {
 	.nr_max_vchans   = 24,
 	.clock_autogate_enable = sun6i_enable_clock_autogate_a23,
 	.set_burst_length = sun6i_set_burst_length_a31,
+	.set_drq          = sun6i_set_drq_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1272,8 +1280,8 @@ static int sun6i_dma_probe(struct platform_device *pdev)
 	ret = of_property_read_u32(np, "dma-requests", &sdc->max_request);
 	if (ret && !sdc->max_request) {
 		dev_info(&pdev->dev, "Missing dma-requests, using %u.\n",
-			 DMA_CHAN_MAX_DRQ);
-		sdc->max_request = DMA_CHAN_MAX_DRQ;
+			 DMA_CHAN_MAX_DRQ_A31);
+		sdc->max_request = DMA_CHAN_MAX_DRQ_A31;
 	}
 
 	/*
-- 
2.20.1

[PATCH v3 4/7] dmaengine: sun6i: Add a quirk for setting mode fields

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 DMA has mode fields in different position than any other currently
supported DMA controller.

Add a quirk for that.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/dma/sun6i-dma.c | 46 ++++++++++++++++++++++++-----------------
 1 file changed, 27 insertions(+), 19 deletions(-)

diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
index f725b93fd21a..f5cb5e89bf7b 100644
--- a/drivers/dma/sun6i-dma.c
+++ b/drivers/dma/sun6i-dma.c
@@ -70,15 +70,13 @@
 #define DMA_CHAN_CUR_CFG	0x0c
 #define DMA_CHAN_MAX_DRQ_A31		0x1f
 #define DMA_CHAN_CFG_SRC_DRQ_A31(x)	((x) & DMA_CHAN_MAX_DRQ_A31)
-#define DMA_CHAN_CFG_SRC_IO_MODE	BIT(5)
-#define DMA_CHAN_CFG_SRC_LINEAR_MODE	(0 << 5)
+#define DMA_CHAN_CFG_SRC_MODE_A31(x)	(((x) & 0x1) << 5)
 #define DMA_CHAN_CFG_SRC_BURST_A31(x)	(((x) & 0x3) << 7)
 #define DMA_CHAN_CFG_SRC_BURST_H3(x)	(((x) & 0x3) << 6)
 #define DMA_CHAN_CFG_SRC_WIDTH(x)	(((x) & 0x3) << 9)
 
 #define DMA_CHAN_CFG_DST_DRQ_A31(x)	(DMA_CHAN_CFG_SRC_DRQ_A31(x) << 16)
-#define DMA_CHAN_CFG_DST_IO_MODE	(DMA_CHAN_CFG_SRC_IO_MODE << 16)
-#define DMA_CHAN_CFG_DST_LINEAR_MODE	(DMA_CHAN_CFG_SRC_LINEAR_MODE << 16)
+#define DMA_CHAN_CFG_DST_MODE_A31(x)	(DMA_CHAN_CFG_SRC_MODE_A31(x) << 16)
 #define DMA_CHAN_CFG_DST_BURST_A31(x)	(DMA_CHAN_CFG_SRC_BURST_A31(x) << 16)
 #define DMA_CHAN_CFG_DST_BURST_H3(x)	(DMA_CHAN_CFG_SRC_BURST_H3(x) << 16)
 #define DMA_CHAN_CFG_DST_WIDTH(x)	(DMA_CHAN_CFG_SRC_WIDTH(x) << 16)
@@ -98,6 +96,8 @@
 #define LLI_LAST_ITEM	0xfffff800
 #define NORMAL_WAIT	8
 #define DRQ_SDRAM	1
+#define LINEAR_MODE     0
+#define IO_MODE         1
 
 /* forward declaration */
 struct sun6i_dma_dev;
@@ -126,6 +126,7 @@ struct sun6i_dma_config {
 	void (*clock_autogate_enable)(struct sun6i_dma_dev *);
 	void (*set_burst_length)(u32 *p_cfg, s8 src_burst, s8 dst_burst);
 	void (*set_drq)(u32 *p_cfg, s8 src_drq, s8 dst_drq);
+	void (*set_mode)(u32 *p_cfg, s8 src_mode, s8 dst_mode);
 	u32 src_burst_lengths;
 	u32 dst_burst_lengths;
 	u32 src_addr_widths;
@@ -318,6 +319,12 @@ static void sun6i_set_drq_a31(u32 *p_cfg, s8 src_drq, s8 dst_drq)
 		  DMA_CHAN_CFG_DST_DRQ_A31(dst_drq);
 }
 
+static void sun6i_set_mode_a31(u32 *p_cfg, s8 src_mode, s8 dst_mode)
+{
+	*p_cfg |= DMA_CHAN_CFG_SRC_MODE_A31(src_mode) |
+		  DMA_CHAN_CFG_DST_MODE_A31(dst_mode);
+}
+
 static size_t sun6i_get_chan_size(struct sun6i_pchan *pchan)
 {
 	struct sun6i_desc *txd = pchan->desc;
@@ -641,13 +648,12 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_dma_memcpy(
 
 	burst = convert_burst(8);
 	width = convert_buswidth(DMA_SLAVE_BUSWIDTH_4_BYTES);
-	v_lli->cfg = DMA_CHAN_CFG_DST_LINEAR_MODE |
-		DMA_CHAN_CFG_SRC_LINEAR_MODE |
-		DMA_CHAN_CFG_SRC_WIDTH(width) |
+	v_lli->cfg = DMA_CHAN_CFG_SRC_WIDTH(width) |
 		DMA_CHAN_CFG_DST_WIDTH(width);
 
 	sdev->cfg->set_burst_length(&v_lli->cfg, burst, burst);
 	sdev->cfg->set_drq(&v_lli->cfg, DRQ_SDRAM, DRQ_SDRAM);
+	sdev->cfg->set_mode(&v_lli->cfg, LINEAR_MODE, LINEAR_MODE);
 
 	sun6i_dma_lli_add(NULL, v_lli, p_lli, txd);
 
@@ -699,10 +705,9 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 		if (dir == DMA_MEM_TO_DEV) {
 			v_lli->src = sg_dma_address(sg);
 			v_lli->dst = sconfig->dst_addr;
-			v_lli->cfg = lli_cfg |
-				DMA_CHAN_CFG_DST_IO_MODE |
-				DMA_CHAN_CFG_SRC_LINEAR_MODE;
+			v_lli->cfg = lli_cfg;
 			sdev->cfg->set_drq(&v_lli->cfg, DRQ_SDRAM, vchan->port);
+			sdev->cfg->set_mode(&v_lli->cfg, LINEAR_MODE, IO_MODE);
 
 			dev_dbg(chan2dev(chan),
 				"%s; chan: %d, dest: %pad, src: %pad, len: %u. flags: 0x%08lx\n",
@@ -713,10 +718,9 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_slave_sg(
 		} else {
 			v_lli->src = sconfig->src_addr;
 			v_lli->dst = sg_dma_address(sg);
-			v_lli->cfg = lli_cfg |
-				DMA_CHAN_CFG_DST_LINEAR_MODE |
-				DMA_CHAN_CFG_SRC_IO_MODE;
+			v_lli->cfg = lli_cfg;
 			sdev->cfg->set_drq(&v_lli->cfg, vchan->port, DRQ_SDRAM);
+			sdev->cfg->set_mode(&v_lli->cfg, IO_MODE, LINEAR_MODE);
 
 			dev_dbg(chan2dev(chan),
 				"%s; chan: %d, dest: %pad, src: %pad, len: %u. flags: 0x%08lx\n",
@@ -782,17 +786,15 @@ static struct dma_async_tx_descriptor *sun6i_dma_prep_dma_cyclic(
 		if (dir == DMA_MEM_TO_DEV) {
 			v_lli->src = buf_addr + period_len * i;
 			v_lli->dst = sconfig->dst_addr;
-			v_lli->cfg = lli_cfg |
-				DMA_CHAN_CFG_DST_IO_MODE |
-				DMA_CHAN_CFG_SRC_LINEAR_MODE;
+			v_lli->cfg = lli_cfg;
 			sdev->cfg->set_drq(&v_lli->cfg, DRQ_SDRAM, vchan->port);
+			sdev->cfg->set_mode(&v_lli->cfg, LINEAR_MODE, IO_MODE);
 		} else {
 			v_lli->src = sconfig->src_addr;
 			v_lli->dst = buf_addr + period_len * i;
-			v_lli->cfg = lli_cfg |
-				DMA_CHAN_CFG_DST_LINEAR_MODE |
-				DMA_CHAN_CFG_SRC_IO_MODE;
+			v_lli->cfg = lli_cfg;
 			sdev->cfg->set_drq(&v_lli->cfg, vchan->port, DRQ_SDRAM);
+			sdev->cfg->set_mode(&v_lli->cfg, IO_MODE, LINEAR_MODE);
 		}
 
 		prev = sun6i_dma_lli_add(prev, v_lli, p_lli, txd);
@@ -1058,6 +1060,7 @@ static struct sun6i_dma_config sun6i_a31_dma_cfg = {
 	.nr_max_vchans   = 53,
 	.set_burst_length = sun6i_set_burst_length_a31,
 	.set_drq          = sun6i_set_drq_a31,
+	.set_mode         = sun6i_set_mode_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1080,6 +1083,7 @@ static struct sun6i_dma_config sun8i_a23_dma_cfg = {
 	.clock_autogate_enable = sun6i_enable_clock_autogate_a23,
 	.set_burst_length = sun6i_set_burst_length_a31,
 	.set_drq          = sun6i_set_drq_a31,
+	.set_mode         = sun6i_set_mode_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1097,6 +1101,7 @@ static struct sun6i_dma_config sun8i_a83t_dma_cfg = {
 	.clock_autogate_enable = sun6i_enable_clock_autogate_a23,
 	.set_burst_length = sun6i_set_burst_length_a31,
 	.set_drq          = sun6i_set_drq_a31,
+	.set_mode         = sun6i_set_mode_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1121,6 +1126,7 @@ static struct sun6i_dma_config sun8i_h3_dma_cfg = {
 	.clock_autogate_enable = sun6i_enable_clock_autogate_h3,
 	.set_burst_length = sun6i_set_burst_length_h3,
 	.set_drq          = sun6i_set_drq_a31,
+	.set_mode         = sun6i_set_mode_a31,
 	.src_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.dst_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1141,6 +1147,7 @@ static struct sun6i_dma_config sun50i_a64_dma_cfg = {
 	.clock_autogate_enable = sun6i_enable_clock_autogate_h3,
 	.set_burst_length = sun6i_set_burst_length_h3,
 	.set_drq          = sun6i_set_drq_a31,
+	.set_mode         = sun6i_set_mode_a31,
 	.src_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.dst_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
@@ -1165,6 +1172,7 @@ static struct sun6i_dma_config sun8i_v3s_dma_cfg = {
 	.clock_autogate_enable = sun6i_enable_clock_autogate_a23,
 	.set_burst_length = sun6i_set_burst_length_a31,
 	.set_drq          = sun6i_set_drq_a31,
+	.set_mode         = sun6i_set_mode_a31,
 	.src_burst_lengths = BIT(1) | BIT(8),
 	.dst_burst_lengths = BIT(1) | BIT(8),
 	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
-- 
2.20.1

[PATCH v3 5/7] dmaengine: sun6i: Add support for H6 DMA

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 DMA has more than 32 supported DRQs, which means that configuration
register is slightly rearranged. It also needs additional clock to be
enabled.

Add support for it.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/dma/sun6i-dma.c | 40 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
index f5cb5e89bf7b..ddef87ebdfdb 100644
--- a/drivers/dma/sun6i-dma.c
+++ b/drivers/dma/sun6i-dma.c
@@ -69,14 +69,19 @@
 
 #define DMA_CHAN_CUR_CFG	0x0c
 #define DMA_CHAN_MAX_DRQ_A31		0x1f
+#define DMA_CHAN_MAX_DRQ_H6		0x3f
 #define DMA_CHAN_CFG_SRC_DRQ_A31(x)	((x) & DMA_CHAN_MAX_DRQ_A31)
+#define DMA_CHAN_CFG_SRC_DRQ_H6(x)	((x) & DMA_CHAN_MAX_DRQ_H6)
 #define DMA_CHAN_CFG_SRC_MODE_A31(x)	(((x) & 0x1) << 5)
+#define DMA_CHAN_CFG_SRC_MODE_H6(x)	(((x) & 0x1) << 8)
 #define DMA_CHAN_CFG_SRC_BURST_A31(x)	(((x) & 0x3) << 7)
 #define DMA_CHAN_CFG_SRC_BURST_H3(x)	(((x) & 0x3) << 6)
 #define DMA_CHAN_CFG_SRC_WIDTH(x)	(((x) & 0x3) << 9)
 
 #define DMA_CHAN_CFG_DST_DRQ_A31(x)	(DMA_CHAN_CFG_SRC_DRQ_A31(x) << 16)
+#define DMA_CHAN_CFG_DST_DRQ_H6(x)	(DMA_CHAN_CFG_SRC_DRQ_H6(x) << 16)
 #define DMA_CHAN_CFG_DST_MODE_A31(x)	(DMA_CHAN_CFG_SRC_MODE_A31(x) << 16)
+#define DMA_CHAN_CFG_DST_MODE_H6(x)	(DMA_CHAN_CFG_SRC_MODE_H6(x) << 16)
 #define DMA_CHAN_CFG_DST_BURST_A31(x)	(DMA_CHAN_CFG_SRC_BURST_A31(x) << 16)
 #define DMA_CHAN_CFG_DST_BURST_H3(x)	(DMA_CHAN_CFG_SRC_BURST_H3(x) << 16)
 #define DMA_CHAN_CFG_DST_WIDTH(x)	(DMA_CHAN_CFG_SRC_WIDTH(x) << 16)
@@ -319,12 +324,24 @@ static void sun6i_set_drq_a31(u32 *p_cfg, s8 src_drq, s8 dst_drq)
 		  DMA_CHAN_CFG_DST_DRQ_A31(dst_drq);
 }
 
+static void sun6i_set_drq_h6(u32 *p_cfg, s8 src_drq, s8 dst_drq)
+{
+	*p_cfg |= DMA_CHAN_CFG_SRC_DRQ_H6(src_drq) |
+		  DMA_CHAN_CFG_DST_DRQ_H6(dst_drq);
+}
+
 static void sun6i_set_mode_a31(u32 *p_cfg, s8 src_mode, s8 dst_mode)
 {
 	*p_cfg |= DMA_CHAN_CFG_SRC_MODE_A31(src_mode) |
 		  DMA_CHAN_CFG_DST_MODE_A31(dst_mode);
 }
 
+static void sun6i_set_mode_h6(u32 *p_cfg, s8 src_mode, s8 dst_mode)
+{
+	*p_cfg |= DMA_CHAN_CFG_SRC_MODE_H6(src_mode) |
+		  DMA_CHAN_CFG_DST_MODE_H6(dst_mode);
+}
+
 static size_t sun6i_get_chan_size(struct sun6i_pchan *pchan)
 {
 	struct sun6i_desc *txd = pchan->desc;
@@ -1160,6 +1177,28 @@ static struct sun6i_dma_config sun50i_a64_dma_cfg = {
 			     BIT(DMA_SLAVE_BUSWIDTH_8_BYTES),
 };
 
+/*
+ * The H6 binding uses the number of dma channels from the
+ * device tree node.
+ */
+static struct sun6i_dma_config sun50i_h6_dma_cfg = {
+	.clock_autogate_enable = sun6i_enable_clock_autogate_h3,
+	.set_burst_length = sun6i_set_burst_length_h3,
+	.set_drq          = sun6i_set_drq_h6,
+	.set_mode         = sun6i_set_mode_h6,
+	.src_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
+	.dst_burst_lengths = BIT(1) | BIT(4) | BIT(8) | BIT(16),
+	.src_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
+			     BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) |
+			     BIT(DMA_SLAVE_BUSWIDTH_4_BYTES) |
+			     BIT(DMA_SLAVE_BUSWIDTH_8_BYTES),
+	.dst_addr_widths   = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |
+			     BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) |
+			     BIT(DMA_SLAVE_BUSWIDTH_4_BYTES) |
+			     BIT(DMA_SLAVE_BUSWIDTH_8_BYTES),
+	.has_mbus_clk = true,
+};
+
 /*
  * The V3s have only 8 physical channels, a maximum DRQ port id of 23,
  * and a total of 24 usable source and destination endpoints.
@@ -1190,6 +1229,7 @@ static const struct of_device_id sun6i_dma_match[] = {
 	{ .compatible = "allwinner,sun8i-h3-dma", .data = &sun8i_h3_dma_cfg },
 	{ .compatible = "allwinner,sun8i-v3s-dma", .data = &sun8i_v3s_dma_cfg },
 	{ .compatible = "allwinner,sun50i-a64-dma", .data = &sun50i_a64_dma_cfg },
+	{ .compatible = "allwinner,sun50i-h6-dma", .data = &sun50i_h6_dma_cfg },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, sun6i_dma_match);
-- 
2.20.1

[PATCH v3 6/7] arm64: dts: allwinner: h6: Add DMA node

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 has DMA controller which supports 16 channels.

Add a node for it.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 16c5c3d0fd81..f4ea596c82ce 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -208,6 +208,18 @@
 			reg = <0x03006000 0x400>;
 		};
 
+		dma: dma-controller@3002000 {
+			compatible = "allwinner,sun50i-h6-dma";
+			reg = <0x03002000 0x1000>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+			clock-names = "bus", "mbus";
+			dma-channels = <16>;
+			dma-requests = <46>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
 		pio: pinctrl@300b000 {
 			compatible = "allwinner,sun50i-h6-pinctrl";
 			reg = <0x0300b000 0x400>;
-- 
2.20.1

[PATCH v3 7/7] arm64: defconfig: enable Allwinner DMA drivers

[Clément Péron]

Allwinner sun6i DMA drivers is used on A64 and H6 boards.

Enable it as a module.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 4d583514258c..b535f0f412cc 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -614,6 +614,7 @@ CONFIG_RTC_DRV_IMX_SC=m
 CONFIG_RTC_DRV_XGENE=y
 CONFIG_DMADEVICES=y
 CONFIG_DMA_BCM2835=m
+CONFIG_DMA_SUN6I=m
 CONFIG_K3_DMA=y
 CONFIG_MV_XOR=y
 CONFIG_MV_XOR_V2=y
-- 
2.20.1

Re: [PATCH v3 0/7] Allwinner H6 DMA support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 954 bytes --]

On Mon, May 27, 2019 at 10:14:52PM +0200, Clément Péron wrote:
> Hi,
>
> This series has been first proposed by Jernej Skrabec[1].
> As this series is mandatory for SPDIF/I2S support and because he is
> busy on Cedrus stuff. I asked him to make the minor change requested
> and repost it.
> Authorship remains to him.
>
> I have tested this series with SPDIF driver and added a patch to enable
> DMA_SUN6I_CONFIG for arm64.
>
> Original Post:
> "
> DMA engine engine on H6 almost the same as on older SoCs. The biggest
> difference is that it has slightly rearranged bits in registers and
> it needs additional clock, probably due to iommu.
>
> These patches were tested with I2S connected to HDMI. I2S needs
> additional patches which will be sent later.

For the whole series,
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v3 1/7] dt-bindings: arm64: allwinner: h6: Add binding for DMA controller

[Vinod Koul]

On 27-05-19, 22:14, Clément Péron wrote:
> From: Jernej Skrabec <jernej.skrabec@siol.net>
> 
> DMA in H6 is similar to other DMA controller, except it is first which
> supports more than 32 request sources and has 16 channels. It also needs
> additional clock to be enabled.
> 

Applied, thanks

-- 
~Vinod

Re: [PATCH v3 2/7] dmaengine: sun6i: Add a quirk for additional mbus clock

[Vinod Koul]

On 27-05-19, 22:14, Clément Péron wrote:
> From: Jernej Skrabec <jernej.skrabec@siol.net>
> 
> H6 DMA controller needs additional mbus clock to be enabled.
> 
> Add a quirk for it and handle it accordingly.

Applied, thanks

-- 
~Vinod

Re: [PATCH v3 3/7] dmaengine: sun6i: Add a quirk for setting DRQ fields

[Vinod Koul]

On 27-05-19, 22:14, Clément Péron wrote:
> From: Jernej Skrabec <jernej.skrabec@siol.net>
> 
> H6 DMA has more than 32 possible DRQs. That means that current maximum
> of 31 DRQs is not enough anymore.
> 
> Add a quirk which will set source and destination DRQ number.

Applied, thanks

-- 
~Vinod

Re: [PATCH v3 4/7] dmaengine: sun6i: Add a quirk for setting mode fields

[Vinod Koul]

On 27-05-19, 22:14, Clément Péron wrote:
> From: Jernej Skrabec <jernej.skrabec@siol.net>
> 
> H6 DMA has mode fields in different position than any other currently
> supported DMA controller.
> 
> Add a quirk for that.

Applied, thanks

-- 
~Vinod

Re: [PATCH v3 5/7] dmaengine: sun6i: Add support for H6 DMA

[Vinod Koul]

On 27-05-19, 22:14, Clément Péron wrote:
> From: Jernej Skrabec <jernej.skrabec@siol.net>
> 
> H6 DMA has more than 32 supported DRQs, which means that configuration
> register is slightly rearranged. It also needs additional clock to be
> enabled.
> 
> Add support for it.

Applied, thanks

-- 
~Vinod

Re: [PATCH v3 0/7] Allwinner H6 DMA support

[Clément Péron]

Hi Maxime,

On Tue, 28 May 2019 at 13:10, Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> On Mon, May 27, 2019 at 10:14:52PM +0200, Clément Péron wrote:
> > Hi,
> >
> > This series has been first proposed by Jernej Skrabec[1].
> > As this series is mandatory for SPDIF/I2S support and because he is
> > busy on Cedrus stuff. I asked him to make the minor change requested
> > and repost it.
> > Authorship remains to him.
> >
> > I have tested this series with SPDIF driver and added a patch to enable
> > DMA_SUN6I_CONFIG for arm64.
> >
> > Original Post:
> > "
> > DMA engine engine on H6 almost the same as on older SoCs. The biggest
> > difference is that it has slightly rearranged bits in registers and
> > it needs additional clock, probably due to iommu.
> >
> > These patches were tested with I2S connected to HDMI. I2S needs
> > additional patches which will be sent later.
>
> For the whole series,
> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

Thanks, Is it ok to pick patch 5/6/7 to sunxi tree ?

Regards,
Clément

>
> Maxime
>
> --
> Maxime Ripard, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com

Re: [PATCH v3 6/7] arm64: dts: allwinner: h6: Add DMA node

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1571 bytes --]

Hi,

I tried applying this patch, and it conflicts.

There's also a minor issue that sohuld be fixed

On Mon, May 27, 2019 at 10:14:58PM +0200, Clément Péron wrote:
> From: Jernej Skrabec <jernej.skrabec@siol.net>
>
> H6 has DMA controller which supports 16 channels.
>
> Add a node for it.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> Signed-off-by: Clément Péron <peron.clem@gmail.com>
> ---
>  arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> index 16c5c3d0fd81..f4ea596c82ce 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
> @@ -208,6 +208,18 @@
>  			reg = <0x03006000 0x400>;
>  		};
>
> +		dma: dma-controller@3002000 {
> +			compatible = "allwinner,sun50i-h6-dma";
> +			reg = <0x03002000 0x1000>;
> +			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
> +			clock-names = "bus", "mbus";
> +			dma-channels = <16>;
> +			dma-requests = <46>;
> +			resets = <&ccu RST_BUS_DMA>;
> +			#dma-cells = <1>;
> +		};
> +
>  		pio: pinctrl@300b000 {
>  			compatible = "allwinner,sun50i-h6-pinctrl";
>  			reg = <0x0300b000 0x400>;

DT nodes are ordered by increasing physical addresses, so this node
shouldn't be there.

Thanks!
Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v3 7/7] arm64: defconfig: enable Allwinner DMA drivers

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 329 bytes --]

On Mon, May 27, 2019 at 10:14:59PM +0200, Clément Péron wrote:
> Allwinner sun6i DMA drivers is used on A64 and H6 boards.
>
> Enable it as a module.
>
> Signed-off-by: Clément Péron <peron.clem@gmail.com>

Applied, thanks
Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]