dmaengine.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Pratyush Yadav <p.yadav@ti.com>
To: Maxime Ripard <mripard@kernel.org>,
	Mauro Carvalho Chehab <mchehab@kernel.org>,
	Rob Herring <robh+dt@kernel.org>, Pratyush Yadav <p.yadav@ti.com>,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Vinod Koul <vkoul@kernel.org>,
	Peter Ujfalusi <peter.ujfalusi@gmail.com>,
	Steve Longerbeam <slongerbeam@gmail.com>,
	Benoit Parrot <bparrot@ti.com>, <linux-media@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-phy@lists.infradead.org>, <dmaengine@vger.kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>,
	Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>,
	Chunfeng Yun <chunfeng.yun@mediatek.com>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Subject: [PATCH v2 04/18] phy: cdns-dphy: Add Rx support
Date: Wed, 26 May 2021 20:52:54 +0530	[thread overview]
Message-ID: <20210526152308.16525-5-p.yadav@ti.com> (raw)
In-Reply-To: <20210526152308.16525-1-p.yadav@ti.com>

The Cadence DPHY can be used to receive image data over the CSI-2
protocol. Add support for Rx mode. The programming sequence differs from
the Tx mode so it is added as a separate set of hooks to isolate the two
paths.

The PHY is in Tx mode by default and it needs to be set in Rx mode by
setting the submode to PHY_MIPI_DPHY_SUBMODE_RX in the set_mode()
callback.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---

(no changes since v1)

 drivers/phy/cadence/cdns-dphy.c | 237 ++++++++++++++++++++++++++++++++
 1 file changed, 237 insertions(+)

diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
index 7d5f7b333893..7bbca679e2bb 100644
--- a/drivers/phy/cadence/cdns-dphy.c
+++ b/drivers/phy/cadence/cdns-dphy.c
@@ -1,11 +1,14 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright: 2017-2018 Cadence Design Systems, Inc.
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #include <linux/bitops.h>
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
@@ -25,10 +28,14 @@
 #define DPHY_PMA_RCLK(reg)		(0x600 + (reg))
 #define DPHY_PMA_RDATA(lane, reg)	(0x700 + ((lane) * 0x100) + (reg))
 #define DPHY_PCS(reg)			(0xb00 + (reg))
+#define DPHY_ISO(reg)			(0xc00 + (reg))
 
 #define DPHY_CMN_SSM			DPHY_PMA_CMN(0x20)
 #define DPHY_CMN_SSM_EN			BIT(0)
+#define DPHY_CMN_RX_BANDGAP_TIMER_MASK	GENMASK(8, 1)
 #define DPHY_CMN_TX_MODE_EN		BIT(9)
+#define DPHY_CMN_RX_MODE_EN		BIT(10)
+#define DPHY_CMN_RX_BANDGAP_TIMER	0x14
 
 #define DPHY_CMN_PWM			DPHY_PMA_CMN(0x40)
 #define DPHY_CMN_PWM_DIV(x)		((x) << 20)
@@ -45,10 +52,27 @@
 #define DPHY_CMN_OPDIV_FROM_REG		BIT(6)
 #define DPHY_CMN_OPDIV(x)		((x) << 7)
 
+#define DPHY_BAND_CFG			DPHY_PCS(0x0)
+#define DPHY_BAND_CFG_LEFT_BAND		GENMASK(4, 0)
+#define DPHY_BAND_CFG_RIGHT_BAND	GENMASK(9, 5)
+
 #define DPHY_PSM_CFG			DPHY_PCS(0x4)
 #define DPHY_PSM_CFG_FROM_REG		BIT(0)
 #define DPHY_PSM_CLK_DIV(x)		((x) << 1)
 
+#define DPHY_POWER_ISLAND_EN_DATA	DPHY_PCS(0x8)
+#define DPHY_POWER_ISLAND_EN_DATA_VAL	0xaaaaaaaa
+#define DPHY_POWER_ISLAND_EN_CLK	DPHY_PCS(0xc)
+#define DPHY_POWER_ISLAND_EN_CLK_VAL	0xaa
+
+#define DPHY_ISO_CL_CTRL_L		DPHY_ISO(0x10)
+#define DPHY_ISO_DL_CTRL_L0		DPHY_ISO(0x14)
+#define DPHY_ISO_DL_CTRL_L1		DPHY_ISO(0x20)
+#define DPHY_ISO_DL_CTRL_L2		DPHY_ISO(0x30)
+#define DPHY_ISO_DL_CTRL_L3		DPHY_ISO(0x3c)
+#define DPHY_ISO_LANE_READY_BIT		0
+#define DPHY_ISO_LANE_READY_TIMEOUT_MS	100UL
+
 #define DSI_HBP_FRAME_OVERHEAD		12
 #define DSI_HSA_FRAME_OVERHEAD		14
 #define DSI_HFP_FRAME_OVERHEAD		6
@@ -57,6 +81,9 @@
 #define DSI_NULL_FRAME_OVERHEAD		6
 #define DSI_EOT_PKT_SIZE		4
 
+#define DPHY_LANES_MIN			1
+#define DPHY_LANES_MAX			4
+
 struct cdns_dphy_cfg {
 	u8 pll_ipdiv;
 	u8 pll_opdiv;
@@ -312,6 +339,214 @@ static const struct cdns_dphy_ops tx_ref_dphy_ops = {
 	.set_psm_div = cdns_dphy_ref_set_psm_div,
 };
 
+static int cdns_dphy_rx_power_on(struct cdns_dphy *dphy)
+{
+	/* Start RX state machine. */
+	writel(DPHY_CMN_SSM_EN | DPHY_CMN_RX_MODE_EN |
+	       FIELD_PREP(DPHY_CMN_RX_BANDGAP_TIMER_MASK,
+			  DPHY_CMN_RX_BANDGAP_TIMER),
+	       dphy->regs + DPHY_CMN_SSM);
+
+	return 0;
+}
+
+static int cdns_dphy_rx_power_off(struct cdns_dphy *dphy)
+{
+	writel(0, dphy->regs + DPHY_CMN_SSM);
+
+	return 0;
+}
+
+static int cdns_dphy_rx_get_band_ctrl(unsigned long hs_clk_rate)
+{
+	unsigned int rate = hs_clk_rate / 1000000UL;
+
+	if (rate < 80 || rate >= 2500)
+		return -EOPNOTSUPP;
+
+	if (rate >= 80 && rate < 100)
+		return 0;
+
+	if (rate >= 100 && rate < 120)
+		return 1;
+
+	if (rate >= 120 && rate < 160)
+		return 2;
+
+	if (rate >= 160 && rate < 200)
+		return 3;
+
+	if (rate >= 200 && rate < 240)
+		return 4;
+
+	if (rate >= 240 && rate < 280)
+		return 5;
+
+	if (rate >= 280 && rate < 320)
+		return 6;
+
+	if (rate >= 320 && rate < 360)
+		return 7;
+
+	if (rate >= 360 && rate < 400)
+		return 8;
+
+	if (rate >= 400 && rate < 480)
+		return 9;
+
+	if (rate >= 480 && rate < 560)
+		return 10;
+
+	if (rate >= 560 && rate < 640)
+		return 11;
+
+	if (rate >= 640 && rate < 720)
+		return 12;
+
+	if (rate >= 720 && rate < 800)
+		return 13;
+
+	if (rate >= 800 && rate < 880)
+		return 14;
+
+	if (rate >= 880 && rate < 1040)
+		return 15;
+
+	if (rate >= 1040 && rate < 1200)
+		return 16;
+
+	if (rate >= 1200 && rate < 1350)
+		return 17;
+
+	if (rate >= 1350 && rate < 1500)
+		return 18;
+
+	if (rate >= 1500 && rate < 1750)
+		return 19;
+
+	if (rate >= 1750 && rate < 2000)
+		return 20;
+
+	if (rate >= 2000 && rate < 2250)
+		return 21;
+
+	if (rate >= 2250 && rate < 2500)
+		return 22;
+
+	/* Unreachable. */
+	WARN(1, "Reached unreachable code.");
+	return -EINVAL;
+}
+
+static int cdns_dphy_rx_wait_for_bit(void __iomem *addr, unsigned int bit)
+{
+	u32 val;
+
+	return readl_relaxed_poll_timeout(addr, val, val & BIT(bit), 10,
+					  DPHY_ISO_LANE_READY_TIMEOUT_MS * 1000);
+}
+
+static int cdns_dphy_rx_wait_lane_ready(struct cdns_dphy *dphy, int lanes)
+{
+	void __iomem *reg = dphy->regs;
+	int ret;
+
+	if (lanes < DPHY_LANES_MIN || lanes > DPHY_LANES_MAX)
+		return -EINVAL;
+
+	/* Clock lane */
+	ret = cdns_dphy_rx_wait_for_bit(reg + DPHY_ISO_CL_CTRL_L,
+					DPHY_ISO_LANE_READY_BIT);
+	if (ret)
+		return ret;
+
+	/* Data lanes. Minimum one lane is mandatory. */
+	ret = cdns_dphy_rx_wait_for_bit(reg + DPHY_ISO_DL_CTRL_L0,
+					DPHY_ISO_LANE_READY_BIT);
+	if (ret)
+		return ret;
+
+	if (lanes < 2)
+		return 0;
+
+	ret = cdns_dphy_rx_wait_for_bit(reg + DPHY_ISO_DL_CTRL_L1,
+					DPHY_ISO_LANE_READY_BIT);
+	if (ret)
+		return ret;
+
+	if (lanes < 3)
+		return 0;
+
+	ret = cdns_dphy_rx_wait_for_bit(reg + DPHY_ISO_DL_CTRL_L2,
+					DPHY_ISO_LANE_READY_BIT);
+	if (ret)
+		return ret;
+
+	if (lanes < 4)
+		return 0;
+
+	ret = cdns_dphy_rx_wait_for_bit(reg + DPHY_ISO_DL_CTRL_L3,
+					DPHY_ISO_LANE_READY_BIT);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int cdns_dphy_rx_configure(struct cdns_dphy *dphy,
+				  union phy_configure_opts *opts)
+{
+	unsigned int reg;
+	int band_ctrl, ret;
+
+	band_ctrl = cdns_dphy_rx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
+	if (band_ctrl < 0)
+		return band_ctrl;
+
+	reg = FIELD_PREP(DPHY_BAND_CFG_LEFT_BAND, band_ctrl) |
+	      FIELD_PREP(DPHY_BAND_CFG_RIGHT_BAND, band_ctrl);
+	writel(reg, dphy->regs + DPHY_BAND_CFG);
+
+	/*
+	 * Set the required power island phase 2 time. This is mandated by DPHY
+	 * specs.
+	 */
+	reg = DPHY_POWER_ISLAND_EN_DATA_VAL;
+	writel(reg, dphy->regs + DPHY_POWER_ISLAND_EN_DATA);
+	reg = DPHY_POWER_ISLAND_EN_CLK_VAL;
+	writel(reg, dphy->regs + DPHY_POWER_ISLAND_EN_CLK);
+
+	ret = cdns_dphy_rx_wait_lane_ready(dphy, opts->mipi_dphy.lanes);
+	if (ret) {
+		dev_err(dphy->dev, "DPHY wait for lane ready timeout\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int cdns_dphy_rx_validate(struct cdns_dphy *dphy, enum phy_mode mode,
+				 int submode, union phy_configure_opts *opts)
+{
+	int ret;
+
+	if (submode != PHY_MIPI_DPHY_SUBMODE_RX)
+		return -EINVAL;
+
+	ret = cdns_dphy_rx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
+	if (ret < 0)
+		return ret;
+
+	return phy_mipi_dphy_config_validate(&opts->mipi_dphy);
+}
+
+static const struct cdns_dphy_ops rx_ref_dphy_ops = {
+	.power_on = cdns_dphy_rx_power_on,
+	.power_off = cdns_dphy_rx_power_off,
+	.configure = cdns_dphy_rx_configure,
+	.validate = cdns_dphy_rx_validate,
+};
+
 /*
  * This is the reference implementation of DPHY hooks. Specific integration of
  * this IP may have to re-implement some of them depending on how they decided
@@ -319,6 +554,7 @@ static const struct cdns_dphy_ops tx_ref_dphy_ops = {
  */
 static const struct cdns_dphy_driver_data ref_dphy_ops = {
 	.tx = &tx_ref_dphy_ops,
+	.rx = &rx_ref_dphy_ops,
 };
 
 static int cdns_dphy_validate(struct phy *phy, enum phy_mode mode, int submode,
@@ -483,5 +719,6 @@ static struct platform_driver cdns_dphy_platform_driver = {
 module_platform_driver(cdns_dphy_platform_driver);
 
 MODULE_AUTHOR("Maxime Ripard <maxime.ripard@bootlin.com>");
+MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>");
 MODULE_DESCRIPTION("Cadence MIPI D-PHY Driver");
 MODULE_LICENSE("GPL");
-- 
2.30.0


  parent reply	other threads:[~2021-05-26 15:23 UTC|newest]

Thread overview: 48+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-05-26 15:22 [PATCH v2 00/18] CSI2RX support on J721E Pratyush Yadav
2021-05-26 15:22 ` [PATCH v2 01/18] phy: Distinguish between Rx and Tx for MIPI D-PHY with submodes Pratyush Yadav
2021-05-26 15:22 ` [PATCH v2 02/18] phy: cdns-dphy: Prepare for Rx support Pratyush Yadav
2021-05-26 15:22 ` [PATCH v2 03/18] phy: cdns-dphy: Allow setting mode Pratyush Yadav
2021-05-26 15:22 ` Pratyush Yadav [this message]
2021-05-28  6:09   ` [PATCH v2 04/18] phy: cdns-dphy: Add Rx support Tomi Valkeinen
2021-05-26 15:22 ` [PATCH v2 05/18] media: ov5640: Use runtime PM to control sensor power Pratyush Yadav
2021-05-28  6:44   ` Tomi Valkeinen
2021-05-28  7:25     ` Pratyush Yadav
2021-05-26 15:22 ` [PATCH v2 06/18] media: cadence: csi2rx: Add external DPHY support Pratyush Yadav
2021-05-28  7:23   ` Tomi Valkeinen
2021-05-28  7:30     ` Pratyush Yadav
2021-05-26 15:22 ` [PATCH v2 07/18] media: cadence: csi2rx: Soft reset the streams before starting capture Pratyush Yadav
2021-05-26 15:22 ` [PATCH v2 08/18] media: cadence: csi2rx: Set the STOP bit when stopping a stream Pratyush Yadav
2021-05-26 15:22 ` [PATCH v2 09/18] media: cadence: csi2rx: Fix stream data configuration Pratyush Yadav
2021-05-26 15:23 ` [PATCH v2 10/18] media: cadence: csi2rx: Populate subdev devnode Pratyush Yadav
2021-05-28  7:16   ` Tomi Valkeinen
2021-05-28  7:24     ` Pratyush Yadav
2021-05-28  7:35       ` Tomi Valkeinen
2021-06-03 12:42         ` Pratyush Yadav
2021-05-26 15:23 ` [PATCH v2 11/18] dmaengine: ti: k3-psil-j721e: Add entry for CSI2RX Pratyush Yadav
2021-05-31  6:51   ` Péter Ujfalusi
2021-05-31  9:16     ` Pratyush Yadav
2021-05-26 15:23 ` [PATCH v2 12/18] media: Re-structure TI platform drivers Pratyush Yadav
2021-05-28  8:29   ` Tomi Valkeinen
2021-05-26 15:23 ` [PATCH v2 13/18] media: ti: Add CSI2RX support for J721E Pratyush Yadav
2021-05-27 13:29   ` Tomi Valkeinen
2021-06-03 12:49     ` Pratyush Yadav
2021-06-04  8:04       ` Tomi Valkeinen
2021-05-26 15:23 ` [PATCH v2 14/18] media: dt-bindings: Add DT bindings for TI J721E CSI2RX driver Pratyush Yadav
2021-05-27 14:23   ` Rob Herring
2021-06-03 12:43     ` Pratyush Yadav
2021-05-26 15:23 ` [PATCH v2 15/18] media: dt-bindings: Convert Cadence CSI2RX binding to YAML Pratyush Yadav
2021-06-01 17:45   ` Rob Herring
2021-06-03 12:23     ` Pratyush Yadav
2021-05-26 15:23 ` [PATCH v2 16/18] phy: dt-bindings: Convert Cadence DPHY " Pratyush Yadav
2021-06-02 19:51   ` Rob Herring
2021-05-26 15:23 ` [PATCH v2 17/18] phy: dt-bindings: cdns,dphy: make clocks optional Pratyush Yadav
2021-06-02 13:27   ` Maxime Ripard
2021-06-03  8:16     ` Pratyush Yadav
2021-06-02 20:03   ` Rob Herring
2021-05-26 15:23 ` [PATCH v2 18/18] phy: dt-bindings: cdns,dphy: add power-domains property Pratyush Yadav
2021-06-02 20:03   ` Rob Herring
2021-05-27 12:42 ` [PATCH v2 00/18] CSI2RX support on J721E Tomi Valkeinen
2021-06-03 12:54   ` Pratyush Yadav
2021-05-27 13:23 ` Tomi Valkeinen
2021-06-03 12:52   ` Pratyush Yadav
2021-06-04  7:54     ` Tomi Valkeinen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210526152308.16525-5-p.yadav@ti.com \
    --to=p.yadav@ti.com \
    --cc=bparrot@ti.com \
    --cc=chunfeng.yun@mediatek.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dmaengine@vger.kernel.org \
    --cc=kishon@ti.com \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=mchehab@kernel.org \
    --cc=mripard@kernel.org \
    --cc=peter.ujfalusi@gmail.com \
    --cc=robh+dt@kernel.org \
    --cc=slongerbeam@gmail.com \
    --cc=tomi.valkeinen@ideasonboard.com \
    --cc=vigneshr@ti.com \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).