From: Biju Das <biju.das.jz@bp.renesas.com>
To: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>,
Vinod Koul <vkoul@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Chris Brandt <Chris.Brandt@renesas.com>,
dmaengine <dmaengine@vger.kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
Chris Paterson <Chris.Paterson2@renesas.com>,
Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>,
Linux-Renesas <linux-renesas-soc@vger.kernel.org>
Subject: RE: [PATCH 1/5] dt-bindings: dma: Document RZ/G2L bindings
Date: Mon, 14 Jun 2021 16:33:03 +0000 [thread overview]
Message-ID: <OS0PR01MB5922D0054E5A5EEFF8B4A92F86319@OS0PR01MB5922.jpnprd01.prod.outlook.com> (raw)
In-Reply-To: <YMeDoj5RFZgbbRSO@pendragon.ideasonboard.com>
Hi Laurent,
> Subject: Re: [PATCH 1/5] dt-bindings: dma: Document RZ/G2L bindings
>
> Hi Biju,
>
> On Mon, Jun 14, 2021 at 04:24:38PM +0000, Biju Das wrote:
> > > On Mon, Jun 14, 2021 at 04:09:04PM +0000, Biju Das wrote:
> > > > > On Mon, Jun 14, 2021 at 12:54:02PM +0000, Biju Das wrote:
> > > > > > > On Fri, Jun 11, 2021 at 1:36 PM Biju Das wrote:
> > > > > > > > Document RZ/G2L DMAC bindings.
> > > > > > > >
> > > > > > > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> > > > > > > > Reviewed-by: Lad Prabhakar
> > > > > > > > <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > > > > >
> > > > > > > Thanks for your patch!
> > > > > > >
> > > > > > > > --- /dev/null
> > > > > > > > +++ b/Documentation/devicetree/bindings/dma/renesas,rz-dma
> > > > > > > > +++ c.ya
> > > > > > > > +++ ml
> > > > > > > > @@ -0,0 +1,132 @@
> > > > > > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > > > > > +%YAML
> > > > > > > > +1.2
> > > > > > > > +---
> > > > > > > > +$id:
> > > > > > > > +https://jpn01.safelinks.protection.outlook.com/?url=http%
> > > > > > > > +3A%2
> > > > > > > > +F%2F
> > > > > > > > +devi
> > > > > > > > +cetree.org%2Fschemas%2Fdma%2Frenesas%2Crz-dmac.yaml%23&am
> > > > > > > > +p;da
> > > > > > > > +ta=0
> > > > > > > > +4%7C
> > > > > > > > +01%7Cbiju.das.jz%40bp.renesas.com%7C4b547e10cbe64b6f4d850
> > > > > > > > +8d92
> > > > > > > > +f2da
> > > > > > > > +0c0%
> > > > > > > > +7C53d82571da1947e49cb4625a166a4a2a%7C0%7C0%7C637592695286
> > > > > > > > +8468
> > > > > > > > +09%7
> > > > > > > > +CUnk
> > > > > > > > +nown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLC
> > > > > > > > +JBTi
> > > > > > > > +I6Ik
> > > > > > > > +1haW
> > > > > > > > +wiLCJXVCI6Mn0%3D%7C1000&sdata=5Jh%2FxPaia5ZOY0CrViQCc
> > > > > > > > +rNtz
> > > > > > > > +uDej
> > > > > > > > +p8wo
> > > > > > > > +Nrx9iO0ht8%3D&reserved=0
> > > > > > > > +$schema:
> > > > > > > > +https://jpn01.safelinks.protection.outlook.com/?url=http%
> > > > > > > > +3A%2
> > > > > > > > +F%2F
> > > > > > > > +devi
> > > > > > > > +cetree.org%2Fmeta-
> > > > > schemas%2Fcore.yaml%23&data=04%7C01%7Cbiju.das.
> > > > > > > > +jz%40bp.renesas.com%7C4b547e10cbe64b6f4d8508d92f2da0c0%7C
> > > > > > > > +53d8
> > > > > > > > +2571
> > > > > > > > +da19
> > > > > > > > +47e49cb4625a166a4a2a%7C0%7C0%7C637592695286846809%7CUnkno
> > > > > > > > +wn%7
> > > > > > > > +CTWF
> > > > > > > > +pbGZ
> > > > > > > > +sb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwi
> > > > > > > > +LCJX
> > > > > > > > +VCI6
> > > > > > > > +Mn0%
> > > > > > > > +3D%7C1000&sdata=5qQ1PljM3e4Bn4%2FjdldYUHRBQL3jArJgRIA
> > > > > > > > +dLnh
> > > > > > > > +Jraw
> > > > > > > > +%3D&
> > > > > > > > +amp;reserved=0
> > > > >
> > > > > *sigh*
> > > > >
> > > > > > > > +
> > > > > > > > +title: Renesas RZ/G2L DMA Controller
> > > > > > > > +
> > > > > > > > +maintainers:
> > > > > > > > + - Biju Das <biju.das.jz@bp.renesas.com>
> > > > > > > > +
> > > > > > > > +allOf:
> > > > > > > > + - $ref: "dma-controller.yaml#"
> > > > > > > > +
> > > > > > > > +properties:
> > > > > > > > + compatible:
> > > > > > > > + items:
> > > > > > > > + - enum:
> > > > > > > > + - renesas,dmac-r9a07g044 # RZ/G2{L,LC}
> > > > > > >
> > > > > > > Please use "renesas,r9a07g044-dmac".
> > > > > >
> > > > > > OK. Will change.
> > > > > >
> > > > > > > > + - const: renesas,rz-dmac
> > > > > > >
> > > > > > > Does this need many changes for RZ/A1H and RZ/A2M?
> > > > > >
> > > > > > It will work on both RZ/A1H and RZ/A2M. I have n't tested since
> I don't have the board.
> > > > > > There is some difference in MID bit size. Other wise both
> identical.
> > > > > >
> > > > > > > > + renesas,rz-dmac-slavecfg:
> > > > > > > > + $ref: /schemas/types.yaml#/definitions/uint32-array
> > > > > > > > + description: |
> > > > > > > > + DMA configuration for a slave channel. Each channel
> > > > > > > > + must have an array of
> > > > > > > > + 3 items as below.
> > > > > > > > + first item in the array is MID+RID
> > > > > > >
> > > > > > > Already in dmas.
> > > > > > >
> > > > > > > > + second item in the array is slave src or dst
> > > > > > > > + address
> > > > > > >
> > > > > > > As pointed out by Rob, already known by the slave driver.
> > > > > > >
> > > > > > > > + third item in the array is channel configuration
> value.
> > > > > > >
> > > > > > > What exactly is this?
> > > > >
> > > > > What would prevent the DMA client from passing the configuration
> > > > > to the DMA channel through the DMA engine API, just like it
> > > > > passes the slave source or destination address ?
> > > >
> > > > On RZ/G2L, there is 1 case(SSIF ch2) where MID+RID is same for both
> tx and rx.
> > > > The only way we can distinguish it is from channel configuration
> value.
> > >
> > > Are those two different hardware DMA channels ? And configuration
> > > values change between the two ?
> >
> > Yes, REQD is different, apart from this Rx have transfer source and Tx
> have Transfer destination.
> > This particular SSIF ch2 is used only for half duplex compared to other
> SSIF channels.
>
> Does this mean there's a single DMA channel, used by two clients, but not
> at the same time as it only supports half-duplex ?
From hardware perspective, it is 2 channel. For eg:- playback/recording use case.
You cannot do simultaneous playback, but you can do playback or record separately.
Cheers,
Biju
> > > > > > > Does the R-Car DMAC have this too? If yes, how does its
> > > > > > > driver handle it?
> > > > > >
> > > > > > On R-CAR DMAC, we have only MID + RID values. Where as here we
> > > > > > have channel configuration value With different set of
> > > > > > parameter as mentioned in Table 16.4.
> > > > > >
> > > > > > Please see Page 569, Table 16.4 On-Chip Module requests section.
> > > > > >
> > > > > > For eg:- as per Rob's suggestion, I have modelled the driver
> > > > > > with the below entries in ALSA driver for playback/record use
> case.
> > > > > >
> > > > > > dmas = <&dmac 0x255 0x10049c18
> CH_CFG(0x1,0x0,0x1,0x0,0x2,0x1,0x1,0x0)>,
> > > > > > <&dmac 0x256 0x10049c1c
> > > > > > CH_CFG(0x0,0x0,0x1,0x0,0x2,0x1,0x1,0x0)>;
> > > > > > dma-names = "tx", "rx";
> > > > > >
> > > > > > Using first parameter, it gets dmac channel. using second and
> > > > > > third parameter it configures the channel.
>
> --
> Regards,
>
> Laurent Pinchart
next prev parent reply other threads:[~2021-06-14 16:33 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-11 11:36 [PATCH 0/5] Add RZ/G2L DMAC support Biju Das
2021-06-11 11:36 ` [PATCH 1/5] dt-bindings: dma: Document RZ/G2L bindings Biju Das
2021-06-11 17:55 ` Rob Herring
2021-06-12 12:17 ` Biju Das
2021-06-11 19:39 ` Rob Herring
2021-06-12 12:26 ` Biju Das
2021-06-14 12:11 ` Geert Uytterhoeven
2021-06-14 12:54 ` Biju Das
2021-06-14 14:29 ` Laurent Pinchart
2021-06-14 16:09 ` Biju Das
2021-06-14 16:17 ` Laurent Pinchart
2021-06-14 16:24 ` Biju Das
2021-06-14 16:28 ` Laurent Pinchart
2021-06-14 16:33 ` Biju Das [this message]
2021-06-14 17:30 ` Laurent Pinchart
2021-06-15 8:06 ` Biju Das
2021-06-11 11:36 ` [PATCH 3/5] drivers: dma: sh: Add DMAC driver for RZ/G2L SoC Biju Das
2021-06-16 10:31 ` Vinod Koul
2021-06-16 11:02 ` Biju Das
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=OS0PR01MB5922D0054E5A5EEFF8B4A92F86319@OS0PR01MB5922.jpnprd01.prod.outlook.com \
--to=biju.das.jz@bp.renesas.com \
--cc=Chris.Brandt@renesas.com \
--cc=Chris.Paterson2@renesas.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=geert@linux-m68k.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).