From: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
To: Harry Wentland <hwentlan@amd.com>
Cc: mario.kleiner.de@gmail.de, Daniel Vetter <daniel.vetter@ffwll.ch>,
Intel Graphics Development <intel-gfx@lists.freedesktop.org>,
Maling list - DRI developers <dri-devel@lists.freedesktop.org>
Subject: Re: [Intel-gfx] [PATCH] drm/i915/dp: Add current maximum eDP link rate to sink_rate array.
Date: Fri, 10 Jan 2020 20:09:44 +0200 [thread overview]
Message-ID: <20200110180944.GL13686@intel.com> (raw)
In-Reply-To: <bae132f3-73e6-5004-c9a9-adb632338268@amd.com>
On Thu, Jan 09, 2020 at 04:26:19PM -0500, Harry Wentland wrote:
>
>
> On 2020-01-09 4:04 p.m., Mario Kleiner wrote:
> > On Thu, Jan 9, 2020 at 8:49 PM Alex Deucher <alexdeucher@gmail.com
> > <mailto:alexdeucher@gmail.com>> wrote:
> >
> > On Thu, Jan 9, 2020 at 11:47 AM Mario Kleiner
> > <mario.kleiner.de@gmail.com <mailto:mario.kleiner.de@gmail.com>>
> > wrote:
> > >
> > > On Thu, Jan 9, 2020 at 4:40 PM Alex Deucher
> > <alexdeucher@gmail.com <mailto:alexdeucher@gmail.com>> wrote:
> > >>
> > >> On Thu, Jan 9, 2020 at 10:08 AM Mario Kleiner
> > >> <mario.kleiner.de@gmail.com
> > <mailto:mario.kleiner.de@gmail.com>> wrote:
> > >> >
> > As Harry mentioned in the other thread, won't this only work if the
> > display was brought up by the vbios? In the suspend/resume case,
> > won't we just fall back to 2.7Gbps?
> >
> > Alex
> >
> >
> > Adding Harry to cc...
> >
> > The code is only executed for eDP. On the Intel side, it seems that
> > intel_edp_init_dpcd() gets only called during driver load /
> > modesetting init, so not on resume.
> >
> > On the AMD DC side, dc_link_detect_helper() has this early no-op
> > return at the beginning:
> >
> > if ((link->connector_signal == SIGNAL_TYPE_LVDS ||
> > link->connector_signal == SIGNAL_TYPE_EDP) &&
> > link->local_sink)
> > return true;
> >
> > So i guess if link->local_sink doesn't get NULL'ed during a
> > suspend/resume cycle, then we never reach the setup code that would
> > overwrite with non vbios settings?
> >
> > Sounds reasonable to me, given that eDP panels are usually fixed
> > internal panels, nothing that gets hot(un-)plugged?
> >
> > I can't test, because suspend/resume with the Polaris gpu on the MBP
> > 2017 is totally broken atm., just as vgaswitcheroo can't do its job.
> > Looks like powering down the gpu works, but powering up doesn't. And
> > also modesetting at vgaswitcheroo switch time is no-go, because the
> > DDC/AUX lines apparently can't be switched on that Apple gmux, and
> > handover of that data seems to be not implemented in current
> > vgaswitcheroo. At the moment switching between AMD only or Intel+AMD
> > Prime setup is quite a pita...
> >
>
> I haven't followed the entire discussion on the i915 thread but for the
> amdgpu dc patch I would prefer a DPCD quirk to override the reported
> link settings with the correct link rate.
We could consider adding a standard function for reading the receiver
caps and applying the quirk there. I have a feeling that putting it
into drm_dp_dpcd_read() would be a bit too low level since it would
prevent reading the non-quirked raw data easily.
--
Ville Syrjälä
Intel
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
next prev parent reply other threads:[~2020-01-10 18:09 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-09 15:07 [PATCH] drm/i915/dp: Add current maximum eDP link rate to sink_rate array Mario Kleiner
2020-01-09 15:26 ` Ville Syrjälä
2020-01-09 15:38 ` Ville Syrjälä
2020-01-09 16:30 ` Mario Kleiner
2020-01-09 16:47 ` Ville Syrjälä
2020-01-09 17:57 ` Mario Kleiner
2020-01-09 18:24 ` Ville Syrjälä
2020-01-09 20:19 ` Mario Kleiner
2020-01-10 13:32 ` Ville Syrjälä
2020-01-10 15:50 ` Mario Kleiner
2020-01-09 16:31 ` Ville Syrjälä
2020-01-09 16:27 ` Mario Kleiner
2020-01-09 15:39 ` Alex Deucher
2020-01-09 16:46 ` Mario Kleiner
2020-01-09 19:49 ` Alex Deucher
2020-01-09 21:04 ` Mario Kleiner
2020-01-09 21:26 ` Harry Wentland
2020-01-10 16:02 ` Mario Kleiner
2020-01-10 18:09 ` Ville Syrjälä [this message]
2020-01-15 12:34 ` [Intel-gfx] " Jani Nikula
2020-01-15 14:17 ` Ville Syrjälä
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200110180944.GL13686@intel.com \
--to=ville.syrjala@linux.intel.com \
--cc=daniel.vetter@ffwll.ch \
--cc=dri-devel@lists.freedesktop.org \
--cc=hwentlan@amd.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=mario.kleiner.de@gmail.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).