On Sun, Aug 21, 2022 at 01:43:40PM +0200, Noralf Trønnes wrote: > > > Den 18.08.2022 17.31, skrev Maxime Ripard: > > On Thu, Aug 18, 2022 at 05:01:38PM +0200, Noralf Trønnes wrote: > >> > >> > >> Den 18.08.2022 01.23, skrev Noralf Trønnes: > >>> > >>> > >>> Den 17.08.2022 15.11, skrev Noralf Trønnes: > >>>> > >>>> > >>>> Den 17.08.2022 13.46, skrev Maxime Ripard: > >>>>> On Tue, Aug 16, 2022 at 09:35:24PM +0200, Noralf Trønnes wrote: > >>>>>> Den 16.08.2022 11.49, skrev Maxime Ripard: > >>>>>>> On Tue, Aug 16, 2022 at 11:42:20AM +0200, Noralf Trønnes wrote: > >>>>>>>> Den 16.08.2022 10.26, skrev Maxime Ripard: > >>>>>>>>> Hi, > >>>>>>>>> > >>>>>>>>> On Mon, Aug 08, 2022 at 02:44:56PM +0200, Noralf Trønnes wrote: > >>>>>>>>>> Den 29.07.2022 18.34, skrev Maxime Ripard: > >>>>>>>>>>> The TV mode property has been around for a while now to select and get the > >>>>>>>>>>> current TV mode output on an analog TV connector. > >>>>>>>>>>> > >>>>>>>>>>> Despite that property name being generic, its content isn't and has been > >>>>>>>>>>> driver-specific which makes it hard to build any generic behaviour on top > >>>>>>>>>>> of it, both in kernel and user-space. > >>>>>>>>>>> > >>>>>>>>>>> Let's create a new bitmask tv norm property, that can contain any of the > >>>>>>>>>>> analog TV standards currently supported by kernel drivers. Each driver can > >>>>>>>>>>> then pass in a bitmask of the modes it supports. > >>>>>>>>>>> > >>>>>>>>>>> We'll then be able to phase out the older tv mode property. > >>>>>>>>>>> > >>>>>>>>>>> Signed-off-by: Maxime Ripard > >>>>>>>>>>> > >>> > >>>>>> How do you test the property? I've used modetest but I can only change > >>>>>> to a tv.mode that matches the current display mode. I can't switch from > >>>>>> ntsc to pal for instance. > >>>>> > >>>>> Yep, if you want to change from PAL to NTSC, it will require a new mode. > >>>>> > >>>> > >>>> So userspace has to check tv.mode first and then create a display mode > >>>> the driver will accept if switching to a different display mode is > >>>> necessary? In other words, userspace can't discover from the kernel > >>>> which display modes a certain tv.mode/norm provides before it is > >>>> selected? If so, maybe libdrm should have some function(s) to deal with > >>>> switching between modes that require a different display mode since > >>>> knowledge about which display modes a tv.mode supports is needed before > >>>> hand. > >>>> > >>> > >>> I haven't used vc4 on Pi4 in mainline before and have finally gotten it > >>> to work. > >>> > >>> I see that the connector reports 2 modes that together fit all tv.norms > >>> so userspace doesn't have to contruct a display mode, but it does need > >>> to know which display mode belongs to a certain tv.norm. > >>> > >>> When I try to use modetest I'm unable to set a mode: > >>> > >>> pi@pi4t:~ $ modetest -M vc4 -s 45:720x480i > >>> setting mode 720x480i-29.97Hz on connectors 45, crtc 68 > >>> failed to set mode: Function not implemented > >>> > >>> The errno is misleading, modetest does a drmModeDirtyFB before checking > >>> the error returned by drmModeSetCrtc. > >>> > >>> Setting the property succeeds, but the modeset still fails: > >>> > >>> pi@pi4t:~ $ modetest -M vc4 -s 45:720x480i -w 45:"tv norm":2 > >>> setting mode 720x480i-29.97Hz on connectors 45, crtc 68 > >>> failed to set mode: Function not implemented > >>> > >>> pi@pi4t:~ $ modetest -M vc4 -c > >>> 37 tv norm: > >>> flags: bitmask > >>> values: NTSC-443=0x1 NTSC-J=0x2 NTSC-M=0x4 PAL-B=0x10 > >>> PAL-M=0x200 PAL-N=0x400 SECAM-B=0x2000 > >>> value: 2 > >>> > >>> Here's the log, can you see if there's anything obvious in there: > >>> https://gist.github.com/notro/a079498bf6b64327105752b2bafa8858 > >>> > >> > >> I'm one step closer as I now have fbcon working, I had forgotten to add > >> enable_tvout=1 and I had disable_fw_kms_setup=1 which disables the > >> video= mode on the kernel commandline. > >> > >> modetest still fails though, after alot of printk sprinkling, I've > >> tracked it down to the drm_mode_equal test in > >> drm_atomic_helper_connector_tv_check(). The aspect ratios differ: > >> > >> [ 61.336295] drm_atomic_helper_connector_tv_check: > >> mode->picture_aspect_ratio=1 > >> [ 61.336301] drm_atomic_helper_connector_tv_check: > >> &crtc_state->mode->picture_aspect_ratio=0 > > > > I haven't seen this when testing, but I'll have a look, thanks! > > I have found the cause, the kernel strips off the aspect ratio in > drm_mode_getconnector() if drm_file->aspect_ratio_allowed is false. So I > think the drm_mode_equal() test needs to be relaxed for > legacy/non-atomic userspace to work. Geert suggested I removed it too, so this check is gone now. > If I use modetest with atomic commit (-a) it works as is, having the > drm_mode_equal() test: > > $ modetest -M vc4 -a -P 61@68:720x480 -s 45:720x480i > > I have a problem because the board hangs, either right away or after I > press to quit modetest. > > I often get this, sometimes after 10s of seconds: > > [ 136.822963] Unhandled fault: asynchronous external abort (0x1211) at > 0x00000000 > ... > [ 137.248496] bcm2711_get_temp [bcm2711_thermal] from > thermal_zone_get_temp+0x54/0x74 > > Unloading bcm2711_thermal didn't help, in that case I got nothing, so > the problem lies elsewhere. > I have even tried with a fresh SD image and a fresh kernel, but it > didn't help. I got this too when working from current next (next-20220825) but it doesn't seem to happen on drm-misc-next-2022-08-20-1, so it's probably something unrelated? > I can switch from NTSC to PAL like this (but it still crashes): > > $ modetest -M vc4 -a -w 45:"tv norm":16 -P 61@68:720x576 -s 45:720x576i I've tested with my current branch, and it work fine with modetest, I'll put my commands in my next iteration so that you can compare? Maxime