* [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set()
@ 2021-04-23 9:26 Liu Ying
2021-04-23 9:26 ` [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true Liu Ying
` (5 more replies)
0 siblings, 6 replies; 13+ messages in thread
From: Liu Ying @ 2021-04-23 9:26 UTC (permalink / raw)
To: dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, narmstrong, linux-kernel,
robert.foss, a.hajda, Laurent.pinchart, robert.chiras, linux-imx
Hi,
This series aims to make the nwl-dsi bridge be able to connect with
more MIPI DSI panels. Some MIPI DSI panel drivers like 'raydium,rm68200'
send MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which
requires the MIPI DSI controller and PHY to be ready beforehand.
However, the existing nwl-dsi driver gets the MIPI DSI controller and
PHY ready in bridge_funcs->pre_enable(), which happens after the
panel_funcs->prepare(). So, this series shifts the bridge operation
ealier from bridge_funcs->pre_enable() to bridge_funcs->mode_set().
Patch 3/3 does the essential bridge operation shift.
Patch 1/3 and 2/3 are split from the original single patch in v2 and
are needed by patch 3/3. This split-up helps clarify changes better.
The split-up is done in this way:
1) Patch 1/3 forces a full modeset when crtc_state->active is changed to
be true(which implies only connector's DPMS is brought out of "Off"
status, though not necessarily). This makes sure ->mode_set() and
->atomic_disable() will be called in pairs.
2) Patch 2/3 removes a check on unchanged HS clock rate from ->mode_set(),
to make sure MIPI DSI controller and PHY are brought up and taken down
in pairs.
3) Patch 3/3 shifts the bridge operation as the last step.
v2->v3:
* Split the single patch in v2 into 3 patches. (Neil)
v1->v2:
* Fix a typo in commit message - s/unchange/unchanged/
Liu Ying (3):
drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is
changed to be true
drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from
->mode_set()
drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in
->mode_set()
drivers/gpu/drm/bridge/nwl-dsi.c | 86 +++++++++++++++++---------------
1 file changed, 46 insertions(+), 40 deletions(-)
--
2.25.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true
2021-04-23 9:26 [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
@ 2021-04-23 9:26 ` Liu Ying
2021-04-30 8:35 ` Neil Armstrong
2021-04-30 9:56 ` Robert Foss
2021-04-23 9:26 ` [PATCH v3 2/3] drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from ->mode_set() Liu Ying
` (4 subsequent siblings)
5 siblings, 2 replies; 13+ messages in thread
From: Liu Ying @ 2021-04-23 9:26 UTC (permalink / raw)
To: dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, narmstrong, linux-kernel,
robert.foss, a.hajda, Laurent.pinchart, robert.chiras, linux-imx
This patch replaces ->mode_fixup() with ->atomic_check() so that
a full modeset can be requested from there when crtc_state->active
is changed to be true(which implies only connector's DPMS is brought
out of "Off" status, though not necessarily). Bridge functions are
added or changed to accommodate the ->atomic_check() callback. That
full modeset is needed by the up-coming patch which gets MIPI DSI
controller and PHY ready in ->mode_set(), because it makes sure
->mode_set() and ->atomic_disable() are called in pairs.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
---
v2->v3:
* Split from the single patch in v2 to clarify changes. (Neil)
drivers/gpu/drm/bridge/nwl-dsi.c | 61 ++++++++++++++++++++------------
1 file changed, 39 insertions(+), 22 deletions(-)
diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
index 66b67402f1acd..c65ca860712d2 100644
--- a/drivers/gpu/drm/bridge/nwl-dsi.c
+++ b/drivers/gpu/drm/bridge/nwl-dsi.c
@@ -21,6 +21,7 @@
#include <linux/sys_soc.h>
#include <linux/time64.h>
+#include <drm/drm_atomic_state_helper.h>
#include <drm/drm_bridge.h>
#include <drm/drm_mipi_dsi.h>
#include <drm/drm_of.h>
@@ -742,7 +743,9 @@ static int nwl_dsi_disable(struct nwl_dsi *dsi)
return 0;
}
-static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
+static void
+nwl_dsi_bridge_atomic_disable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
{
struct nwl_dsi *dsi = bridge_to_dsi(bridge);
int ret;
@@ -803,17 +806,6 @@ static int nwl_dsi_get_dphy_params(struct nwl_dsi *dsi,
return 0;
}
-static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
- const struct drm_display_mode *mode,
- struct drm_display_mode *adjusted_mode)
-{
- /* At least LCDIF + NWL needs active high sync */
- adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
- adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
-
- return true;
-}
-
static enum drm_mode_status
nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
const struct drm_display_info *info,
@@ -831,6 +823,24 @@ nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
return MODE_OK;
}
+static int nwl_dsi_bridge_atomic_check(struct drm_bridge *bridge,
+ struct drm_bridge_state *bridge_state,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *conn_state)
+{
+ struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
+
+ /* At least LCDIF + NWL needs active high sync */
+ adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
+ adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
+
+ /* Do a full modeset if crtc_state->active is changed to be true. */
+ if (crtc_state->active_changed && crtc_state->active)
+ crtc_state->mode_changed = true;
+
+ return 0;
+}
+
static void
nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
const struct drm_display_mode *mode,
@@ -862,7 +872,9 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
drm_mode_debug_printmodeline(adjusted_mode);
}
-static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
+static void
+nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
{
struct nwl_dsi *dsi = bridge_to_dsi(bridge);
int ret;
@@ -897,7 +909,9 @@ static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
}
}
-static void nwl_dsi_bridge_enable(struct drm_bridge *bridge)
+static void
+nwl_dsi_bridge_atomic_enable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
{
struct nwl_dsi *dsi = bridge_to_dsi(bridge);
int ret;
@@ -942,14 +956,17 @@ static void nwl_dsi_bridge_detach(struct drm_bridge *bridge)
}
static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
- .pre_enable = nwl_dsi_bridge_pre_enable,
- .enable = nwl_dsi_bridge_enable,
- .disable = nwl_dsi_bridge_disable,
- .mode_fixup = nwl_dsi_bridge_mode_fixup,
- .mode_set = nwl_dsi_bridge_mode_set,
- .mode_valid = nwl_dsi_bridge_mode_valid,
- .attach = nwl_dsi_bridge_attach,
- .detach = nwl_dsi_bridge_detach,
+ .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+ .atomic_reset = drm_atomic_helper_bridge_reset,
+ .atomic_check = nwl_dsi_bridge_atomic_check,
+ .atomic_pre_enable = nwl_dsi_bridge_atomic_pre_enable,
+ .atomic_enable = nwl_dsi_bridge_atomic_enable,
+ .atomic_disable = nwl_dsi_bridge_atomic_disable,
+ .mode_set = nwl_dsi_bridge_mode_set,
+ .mode_valid = nwl_dsi_bridge_mode_valid,
+ .attach = nwl_dsi_bridge_attach,
+ .detach = nwl_dsi_bridge_detach,
};
static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
--
2.25.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v3 2/3] drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from ->mode_set()
2021-04-23 9:26 [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
2021-04-23 9:26 ` [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true Liu Ying
@ 2021-04-23 9:26 ` Liu Ying
2021-04-30 8:35 ` Neil Armstrong
2021-04-23 9:26 ` [PATCH v3 3/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
` (3 subsequent siblings)
5 siblings, 1 reply; 13+ messages in thread
From: Liu Ying @ 2021-04-23 9:26 UTC (permalink / raw)
To: dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, narmstrong, linux-kernel,
robert.foss, a.hajda, Laurent.pinchart, robert.chiras, linux-imx
The check on unchanged HS clock rate in ->mode_set() improves
the callback's performance a bit by early return. However,
the up-coming patch would get MIPI DSI controller and PHY ready
in ->mode_set() after that check, thus likely skipped.
So, this patch removes that check to make sure MIPI DSI controller
and PHY will be brought up and taken down from ->mode_set() and
->atomic_disable() respectively in pairs.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
---
v2->v3:
* Split from the single patch in v2 to clarify changes. (Neil)
drivers/gpu/drm/bridge/nwl-dsi.c | 7 -------
1 file changed, 7 deletions(-)
diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
index c65ca860712d2..601ccc4a7cdc7 100644
--- a/drivers/gpu/drm/bridge/nwl-dsi.c
+++ b/drivers/gpu/drm/bridge/nwl-dsi.c
@@ -856,13 +856,6 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
if (ret < 0)
return;
- /*
- * If hs clock is unchanged, we're all good - all parameters are
- * derived from it atm.
- */
- if (new_cfg.mipi_dphy.hs_clk_rate == dsi->phy_cfg.mipi_dphy.hs_clk_rate)
- return;
-
phy_ref_rate = clk_get_rate(dsi->phy_ref_clk);
DRM_DEV_DEBUG_DRIVER(dev, "PHY at ref rate: %lu\n", phy_ref_rate);
/* Save the new desired phy config */
--
2.25.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v3 3/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set()
2021-04-23 9:26 [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
2021-04-23 9:26 ` [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true Liu Ying
2021-04-23 9:26 ` [PATCH v3 2/3] drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from ->mode_set() Liu Ying
@ 2021-04-23 9:26 ` Liu Ying
2021-04-30 8:35 ` Neil Armstrong
2021-04-26 7:43 ` [PATCH v3 0/3] " Neil Armstrong
` (2 subsequent siblings)
5 siblings, 1 reply; 13+ messages in thread
From: Liu Ying @ 2021-04-23 9:26 UTC (permalink / raw)
To: dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, narmstrong, linux-kernel,
robert.foss, a.hajda, Laurent.pinchart, robert.chiras, linux-imx
Some MIPI DSI panel drivers like 'raydium,rm68200' send
MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which
requires the MIPI DSI controller and PHY to be ready beforehand.
Without this patch, the nwl-dsi driver gets the MIPI DSI controller
and PHY ready in bridge_funcs->atomic_pre_enable(), which happens after
the panel_funcs->prepare(). So, this patch shifts the bridge operation
ealier from bridge_funcs->atomic_pre_enable() to bridge_funcs->mode_set().
This way, more MIPI DSI panels can connect to this nwl-dsi bridge.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
---
v2->v3:
* Split some changes to patch 1/3 and 2/3, to clarify changes. (Neil)
v1->v2:
* Fix a typo in commit message - s/unchange/unchanged/
drivers/gpu/drm/bridge/nwl-dsi.c | 28 ++++++++++++----------------
1 file changed, 12 insertions(+), 16 deletions(-)
diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
index 601ccc4a7cdc7..873995f0a7416 100644
--- a/drivers/gpu/drm/bridge/nwl-dsi.c
+++ b/drivers/gpu/drm/bridge/nwl-dsi.c
@@ -662,7 +662,7 @@ static irqreturn_t nwl_dsi_irq_handler(int irq, void *data)
return IRQ_HANDLED;
}
-static int nwl_dsi_enable(struct nwl_dsi *dsi)
+static int nwl_dsi_mode_set(struct nwl_dsi *dsi)
{
struct device *dev = dsi->dev;
union phy_configure_opts *phy_cfg = &dsi->phy_cfg;
@@ -834,7 +834,12 @@ static int nwl_dsi_bridge_atomic_check(struct drm_bridge *bridge,
adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
- /* Do a full modeset if crtc_state->active is changed to be true. */
+ /*
+ * Do a full modeset if crtc_state->active is changed to be true.
+ * This ensures our ->mode_set() is called to get the DSI controller
+ * and the PHY ready to send DCS commands, when only the connector's
+ * DPMS is brought out of "Off" status.
+ */
if (crtc_state->active_changed && crtc_state->active)
crtc_state->mode_changed = true;
@@ -863,16 +868,8 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
drm_mode_debug_printmodeline(adjusted_mode);
-}
-
-static void
-nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
- struct drm_bridge_state *old_bridge_state)
-{
- struct nwl_dsi *dsi = bridge_to_dsi(bridge);
- int ret;
- pm_runtime_get_sync(dsi->dev);
+ pm_runtime_get_sync(dev);
if (clk_prepare_enable(dsi->lcdif_clk) < 0)
return;
@@ -882,22 +879,22 @@ nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
/* Step 1 from DSI reset-out instructions */
ret = reset_control_deassert(dsi->rst_pclk);
if (ret < 0) {
- DRM_DEV_ERROR(dsi->dev, "Failed to deassert PCLK: %d\n", ret);
+ DRM_DEV_ERROR(dev, "Failed to deassert PCLK: %d\n", ret);
return;
}
/* Step 2 from DSI reset-out instructions */
- nwl_dsi_enable(dsi);
+ nwl_dsi_mode_set(dsi);
/* Step 3 from DSI reset-out instructions */
ret = reset_control_deassert(dsi->rst_esc);
if (ret < 0) {
- DRM_DEV_ERROR(dsi->dev, "Failed to deassert ESC: %d\n", ret);
+ DRM_DEV_ERROR(dev, "Failed to deassert ESC: %d\n", ret);
return;
}
ret = reset_control_deassert(dsi->rst_byte);
if (ret < 0) {
- DRM_DEV_ERROR(dsi->dev, "Failed to deassert BYTE: %d\n", ret);
+ DRM_DEV_ERROR(dev, "Failed to deassert BYTE: %d\n", ret);
return;
}
}
@@ -953,7 +950,6 @@ static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
.atomic_reset = drm_atomic_helper_bridge_reset,
.atomic_check = nwl_dsi_bridge_atomic_check,
- .atomic_pre_enable = nwl_dsi_bridge_atomic_pre_enable,
.atomic_enable = nwl_dsi_bridge_atomic_enable,
.atomic_disable = nwl_dsi_bridge_atomic_disable,
.mode_set = nwl_dsi_bridge_mode_set,
--
2.25.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set()
2021-04-23 9:26 [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
` (2 preceding siblings ...)
2021-04-23 9:26 ` [PATCH v3 3/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
@ 2021-04-26 7:43 ` Neil Armstrong
2021-04-30 8:35 ` Neil Armstrong
2021-04-30 9:17 ` Guido Günther
5 siblings, 0 replies; 13+ messages in thread
From: Neil Armstrong @ 2021-04-26 7:43 UTC (permalink / raw)
To: dri-devel
Hi,
On 23/04/2021 11:26, Liu Ying wrote:
> Hi,
>
> This series aims to make the nwl-dsi bridge be able to connect with
> more MIPI DSI panels. Some MIPI DSI panel drivers like 'raydium,rm68200'
> send MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which
> requires the MIPI DSI controller and PHY to be ready beforehand.
> However, the existing nwl-dsi driver gets the MIPI DSI controller and
> PHY ready in bridge_funcs->pre_enable(), which happens after the
> panel_funcs->prepare(). So, this series shifts the bridge operation
> ealier from bridge_funcs->pre_enable() to bridge_funcs->mode_set().
>
> Patch 3/3 does the essential bridge operation shift.
>
> Patch 1/3 and 2/3 are split from the original single patch in v2 and
> are needed by patch 3/3. This split-up helps clarify changes better.
> The split-up is done in this way:
>
> 1) Patch 1/3 forces a full modeset when crtc_state->active is changed to
> be true(which implies only connector's DPMS is brought out of "Off"
> status, though not necessarily). This makes sure ->mode_set() and
> ->atomic_disable() will be called in pairs.
> 2) Patch 2/3 removes a check on unchanged HS clock rate from ->mode_set(),
> to make sure MIPI DSI controller and PHY are brought up and taken down
> in pairs.
> 3) Patch 3/3 shifts the bridge operation as the last step.
>
>
> v2->v3:
> * Split the single patch in v2 into 3 patches. (Neil)
>
> v1->v2:
> * Fix a typo in commit message - s/unchange/unchanged/
>
>
> Liu Ying (3):
> drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is
> changed to be true
> drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from
> ->mode_set()
> drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in
> ->mode_set()
>
> drivers/gpu/drm/bridge/nwl-dsi.c | 86 +++++++++++++++++---------------
> 1 file changed, 46 insertions(+), 40 deletions(-)
>
The patchset looks fine, I'll leave a few days for Laurent or Rob to eventually comment.
Thanks,
Neil
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true
2021-04-23 9:26 ` [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true Liu Ying
@ 2021-04-30 8:35 ` Neil Armstrong
2021-04-30 9:56 ` Robert Foss
1 sibling, 0 replies; 13+ messages in thread
From: Neil Armstrong @ 2021-04-30 8:35 UTC (permalink / raw)
To: Liu Ying, dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, linux-kernel, robert.foss,
a.hajda, Laurent.pinchart, robert.chiras, linux-imx
On 23/04/2021 11:26, Liu Ying wrote:
> This patch replaces ->mode_fixup() with ->atomic_check() so that
> a full modeset can be requested from there when crtc_state->active
> is changed to be true(which implies only connector's DPMS is brought
> out of "Off" status, though not necessarily). Bridge functions are
> added or changed to accommodate the ->atomic_check() callback. That
> full modeset is needed by the up-coming patch which gets MIPI DSI
> controller and PHY ready in ->mode_set(), because it makes sure
> ->mode_set() and ->atomic_disable() are called in pairs.
>
> Cc: Andrzej Hajda <a.hajda@samsung.com>
> Cc: Neil Armstrong <narmstrong@baylibre.com>
> Cc: Robert Foss <robert.foss@linaro.org>
> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
> Cc: Jonas Karlman <jonas@kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec@siol.net>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Daniel Vetter <daniel@ffwll.ch>
> Cc: Guido Günther <agx@sigxcpu.org>
> Cc: Robert Chiras <robert.chiras@nxp.com>
> Cc: NXP Linux Team <linux-imx@nxp.com>
> Signed-off-by: Liu Ying <victor.liu@nxp.com>
> ---
> v2->v3:
> * Split from the single patch in v2 to clarify changes. (Neil)
>
> drivers/gpu/drm/bridge/nwl-dsi.c | 61 ++++++++++++++++++++------------
> 1 file changed, 39 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
> index 66b67402f1acd..c65ca860712d2 100644
> --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> @@ -21,6 +21,7 @@
> #include <linux/sys_soc.h>
> #include <linux/time64.h>
>
> +#include <drm/drm_atomic_state_helper.h>
> #include <drm/drm_bridge.h>
> #include <drm/drm_mipi_dsi.h>
> #include <drm/drm_of.h>
> @@ -742,7 +743,9 @@ static int nwl_dsi_disable(struct nwl_dsi *dsi)
> return 0;
> }
>
> -static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
> +static void
> +nwl_dsi_bridge_atomic_disable(struct drm_bridge *bridge,
> + struct drm_bridge_state *old_bridge_state)
> {
> struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> int ret;
> @@ -803,17 +806,6 @@ static int nwl_dsi_get_dphy_params(struct nwl_dsi *dsi,
> return 0;
> }
>
> -static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
> - const struct drm_display_mode *mode,
> - struct drm_display_mode *adjusted_mode)
> -{
> - /* At least LCDIF + NWL needs active high sync */
> - adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
> - adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
> -
> - return true;
> -}
> -
> static enum drm_mode_status
> nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> const struct drm_display_info *info,
> @@ -831,6 +823,24 @@ nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> return MODE_OK;
> }
>
> +static int nwl_dsi_bridge_atomic_check(struct drm_bridge *bridge,
> + struct drm_bridge_state *bridge_state,
> + struct drm_crtc_state *crtc_state,
> + struct drm_connector_state *conn_state)
> +{
> + struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode;
> +
> + /* At least LCDIF + NWL needs active high sync */
> + adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
> + adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
> +
> + /* Do a full modeset if crtc_state->active is changed to be true. */
> + if (crtc_state->active_changed && crtc_state->active)
> + crtc_state->mode_changed = true;
> +
> + return 0;
> +}
> +
> static void
> nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> const struct drm_display_mode *mode,
> @@ -862,7 +872,9 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> drm_mode_debug_printmodeline(adjusted_mode);
> }
>
> -static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
> +static void
> +nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
> + struct drm_bridge_state *old_bridge_state)
> {
> struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> int ret;
> @@ -897,7 +909,9 @@ static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
> }
> }
>
> -static void nwl_dsi_bridge_enable(struct drm_bridge *bridge)
> +static void
> +nwl_dsi_bridge_atomic_enable(struct drm_bridge *bridge,
> + struct drm_bridge_state *old_bridge_state)
> {
> struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> int ret;
> @@ -942,14 +956,17 @@ static void nwl_dsi_bridge_detach(struct drm_bridge *bridge)
> }
>
> static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
> - .pre_enable = nwl_dsi_bridge_pre_enable,
> - .enable = nwl_dsi_bridge_enable,
> - .disable = nwl_dsi_bridge_disable,
> - .mode_fixup = nwl_dsi_bridge_mode_fixup,
> - .mode_set = nwl_dsi_bridge_mode_set,
> - .mode_valid = nwl_dsi_bridge_mode_valid,
> - .attach = nwl_dsi_bridge_attach,
> - .detach = nwl_dsi_bridge_detach,
> + .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
> + .atomic_reset = drm_atomic_helper_bridge_reset,
> + .atomic_check = nwl_dsi_bridge_atomic_check,
> + .atomic_pre_enable = nwl_dsi_bridge_atomic_pre_enable,
> + .atomic_enable = nwl_dsi_bridge_atomic_enable,
> + .atomic_disable = nwl_dsi_bridge_atomic_disable,
> + .mode_set = nwl_dsi_bridge_mode_set,
> + .mode_valid = nwl_dsi_bridge_mode_valid,
> + .attach = nwl_dsi_bridge_attach,
> + .detach = nwl_dsi_bridge_detach,
> };
>
> static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 2/3] drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from ->mode_set()
2021-04-23 9:26 ` [PATCH v3 2/3] drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from ->mode_set() Liu Ying
@ 2021-04-30 8:35 ` Neil Armstrong
0 siblings, 0 replies; 13+ messages in thread
From: Neil Armstrong @ 2021-04-30 8:35 UTC (permalink / raw)
To: Liu Ying, dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, linux-kernel, robert.foss,
a.hajda, Laurent.pinchart, robert.chiras, linux-imx
On 23/04/2021 11:26, Liu Ying wrote:
> The check on unchanged HS clock rate in ->mode_set() improves
> the callback's performance a bit by early return. However,
> the up-coming patch would get MIPI DSI controller and PHY ready
> in ->mode_set() after that check, thus likely skipped.
> So, this patch removes that check to make sure MIPI DSI controller
> and PHY will be brought up and taken down from ->mode_set() and
> ->atomic_disable() respectively in pairs.
>
> Cc: Andrzej Hajda <a.hajda@samsung.com>
> Cc: Neil Armstrong <narmstrong@baylibre.com>
> Cc: Robert Foss <robert.foss@linaro.org>
> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
> Cc: Jonas Karlman <jonas@kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec@siol.net>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Daniel Vetter <daniel@ffwll.ch>
> Cc: Guido Günther <agx@sigxcpu.org>
> Cc: Robert Chiras <robert.chiras@nxp.com>
> Cc: NXP Linux Team <linux-imx@nxp.com>
> Signed-off-by: Liu Ying <victor.liu@nxp.com>
> ---
> v2->v3:
> * Split from the single patch in v2 to clarify changes. (Neil)
>
> drivers/gpu/drm/bridge/nwl-dsi.c | 7 -------
> 1 file changed, 7 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
> index c65ca860712d2..601ccc4a7cdc7 100644
> --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> @@ -856,13 +856,6 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> if (ret < 0)
> return;
>
> - /*
> - * If hs clock is unchanged, we're all good - all parameters are
> - * derived from it atm.
> - */
> - if (new_cfg.mipi_dphy.hs_clk_rate == dsi->phy_cfg.mipi_dphy.hs_clk_rate)
> - return;
> -
> phy_ref_rate = clk_get_rate(dsi->phy_ref_clk);
> DRM_DEV_DEBUG_DRIVER(dev, "PHY at ref rate: %lu\n", phy_ref_rate);
> /* Save the new desired phy config */
>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 3/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set()
2021-04-23 9:26 ` [PATCH v3 3/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
@ 2021-04-30 8:35 ` Neil Armstrong
0 siblings, 0 replies; 13+ messages in thread
From: Neil Armstrong @ 2021-04-30 8:35 UTC (permalink / raw)
To: Liu Ying, dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, linux-kernel, robert.foss,
a.hajda, Laurent.pinchart, robert.chiras, linux-imx
On 23/04/2021 11:26, Liu Ying wrote:
> Some MIPI DSI panel drivers like 'raydium,rm68200' send
> MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which
> requires the MIPI DSI controller and PHY to be ready beforehand.
> Without this patch, the nwl-dsi driver gets the MIPI DSI controller
> and PHY ready in bridge_funcs->atomic_pre_enable(), which happens after
> the panel_funcs->prepare(). So, this patch shifts the bridge operation
> ealier from bridge_funcs->atomic_pre_enable() to bridge_funcs->mode_set().
> This way, more MIPI DSI panels can connect to this nwl-dsi bridge.
>
> Cc: Andrzej Hajda <a.hajda@samsung.com>
> Cc: Neil Armstrong <narmstrong@baylibre.com>
> Cc: Robert Foss <robert.foss@linaro.org>
> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
> Cc: Jonas Karlman <jonas@kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec@siol.net>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Daniel Vetter <daniel@ffwll.ch>
> Cc: Guido Günther <agx@sigxcpu.org>
> Cc: Robert Chiras <robert.chiras@nxp.com>
> Cc: NXP Linux Team <linux-imx@nxp.com>
> Signed-off-by: Liu Ying <victor.liu@nxp.com>
> ---
> v2->v3:
> * Split some changes to patch 1/3 and 2/3, to clarify changes. (Neil)
>
> v1->v2:
> * Fix a typo in commit message - s/unchange/unchanged/
>
> drivers/gpu/drm/bridge/nwl-dsi.c | 28 ++++++++++++----------------
> 1 file changed, 12 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
> index 601ccc4a7cdc7..873995f0a7416 100644
> --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> @@ -662,7 +662,7 @@ static irqreturn_t nwl_dsi_irq_handler(int irq, void *data)
> return IRQ_HANDLED;
> }
>
> -static int nwl_dsi_enable(struct nwl_dsi *dsi)
> +static int nwl_dsi_mode_set(struct nwl_dsi *dsi)
> {
> struct device *dev = dsi->dev;
> union phy_configure_opts *phy_cfg = &dsi->phy_cfg;
> @@ -834,7 +834,12 @@ static int nwl_dsi_bridge_atomic_check(struct drm_bridge *bridge,
> adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
> adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
>
> - /* Do a full modeset if crtc_state->active is changed to be true. */
> + /*
> + * Do a full modeset if crtc_state->active is changed to be true.
> + * This ensures our ->mode_set() is called to get the DSI controller
> + * and the PHY ready to send DCS commands, when only the connector's
> + * DPMS is brought out of "Off" status.
> + */
> if (crtc_state->active_changed && crtc_state->active)
> crtc_state->mode_changed = true;
>
> @@ -863,16 +868,8 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
>
> memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
> drm_mode_debug_printmodeline(adjusted_mode);
> -}
> -
> -static void
> -nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
> - struct drm_bridge_state *old_bridge_state)
> -{
> - struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> - int ret;
>
> - pm_runtime_get_sync(dsi->dev);
> + pm_runtime_get_sync(dev);
>
> if (clk_prepare_enable(dsi->lcdif_clk) < 0)
> return;
> @@ -882,22 +879,22 @@ nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
> /* Step 1 from DSI reset-out instructions */
> ret = reset_control_deassert(dsi->rst_pclk);
> if (ret < 0) {
> - DRM_DEV_ERROR(dsi->dev, "Failed to deassert PCLK: %d\n", ret);
> + DRM_DEV_ERROR(dev, "Failed to deassert PCLK: %d\n", ret);
> return;
> }
>
> /* Step 2 from DSI reset-out instructions */
> - nwl_dsi_enable(dsi);
> + nwl_dsi_mode_set(dsi);
>
> /* Step 3 from DSI reset-out instructions */
> ret = reset_control_deassert(dsi->rst_esc);
> if (ret < 0) {
> - DRM_DEV_ERROR(dsi->dev, "Failed to deassert ESC: %d\n", ret);
> + DRM_DEV_ERROR(dev, "Failed to deassert ESC: %d\n", ret);
> return;
> }
> ret = reset_control_deassert(dsi->rst_byte);
> if (ret < 0) {
> - DRM_DEV_ERROR(dsi->dev, "Failed to deassert BYTE: %d\n", ret);
> + DRM_DEV_ERROR(dev, "Failed to deassert BYTE: %d\n", ret);
> return;
> }
> }
> @@ -953,7 +950,6 @@ static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
> .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
> .atomic_reset = drm_atomic_helper_bridge_reset,
> .atomic_check = nwl_dsi_bridge_atomic_check,
> - .atomic_pre_enable = nwl_dsi_bridge_atomic_pre_enable,
> .atomic_enable = nwl_dsi_bridge_atomic_enable,
> .atomic_disable = nwl_dsi_bridge_atomic_disable,
> .mode_set = nwl_dsi_bridge_mode_set,
>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set()
2021-04-23 9:26 [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
` (3 preceding siblings ...)
2021-04-26 7:43 ` [PATCH v3 0/3] " Neil Armstrong
@ 2021-04-30 8:35 ` Neil Armstrong
2021-04-30 9:17 ` Guido Günther
5 siblings, 0 replies; 13+ messages in thread
From: Neil Armstrong @ 2021-04-30 8:35 UTC (permalink / raw)
To: Liu Ying, dri-devel
Cc: jernej.skrabec, jonas, airlied, agx, linux-kernel, robert.foss,
a.hajda, Laurent.pinchart, robert.chiras, linux-imx
On 23/04/2021 11:26, Liu Ying wrote:
> Hi,
>
> This series aims to make the nwl-dsi bridge be able to connect with
> more MIPI DSI panels. Some MIPI DSI panel drivers like 'raydium,rm68200'
> send MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which
> requires the MIPI DSI controller and PHY to be ready beforehand.
> However, the existing nwl-dsi driver gets the MIPI DSI controller and
> PHY ready in bridge_funcs->pre_enable(), which happens after the
> panel_funcs->prepare(). So, this series shifts the bridge operation
> ealier from bridge_funcs->pre_enable() to bridge_funcs->mode_set().
>
> Patch 3/3 does the essential bridge operation shift.
>
> Patch 1/3 and 2/3 are split from the original single patch in v2 and
> are needed by patch 3/3. This split-up helps clarify changes better.
> The split-up is done in this way:
>
> 1) Patch 1/3 forces a full modeset when crtc_state->active is changed to
> be true(which implies only connector's DPMS is brought out of "Off"
> status, though not necessarily). This makes sure ->mode_set() and
> ->atomic_disable() will be called in pairs.
> 2) Patch 2/3 removes a check on unchanged HS clock rate from ->mode_set(),
> to make sure MIPI DSI controller and PHY are brought up and taken down
> in pairs.
> 3) Patch 3/3 shifts the bridge operation as the last step.
>
>
> v2->v3:
> * Split the single patch in v2 into 3 patches. (Neil)
>
> v1->v2:
> * Fix a typo in commit message - s/unchange/unchanged/
>
>
> Liu Ying (3):
> drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is
> changed to be true
> drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from
> ->mode_set()
> drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in
> ->mode_set()
>
> drivers/gpu/drm/bridge/nwl-dsi.c | 86 +++++++++++++++++---------------
> 1 file changed, 46 insertions(+), 40 deletions(-)
>
Applying to drm-misc-next
Thanks,
Neil
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set()
2021-04-23 9:26 [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
` (4 preceding siblings ...)
2021-04-30 8:35 ` Neil Armstrong
@ 2021-04-30 9:17 ` Guido Günther
5 siblings, 0 replies; 13+ messages in thread
From: Guido Günther @ 2021-04-30 9:17 UTC (permalink / raw)
To: Liu Ying
Cc: jernej.skrabec, narmstrong, airlied, dri-devel, jonas,
linux-kernel, robert.foss, a.hajda, Laurent.pinchart,
robert.chiras, linux-imx
Hi Liu,
On Fri, Apr 23, 2021 at 05:26:40PM +0800, Liu Ying wrote:
> Hi,
>
> This series aims to make the nwl-dsi bridge be able to connect with
> more MIPI DSI panels. Some MIPI DSI panel drivers like 'raydium,rm68200'
> send MIPI_DCS_SET_DISPLAY_ON commands in panel_funcs->prepare(), which
> requires the MIPI DSI controller and PHY to be ready beforehand.
> However, the existing nwl-dsi driver gets the MIPI DSI controller and
> PHY ready in bridge_funcs->pre_enable(), which happens after the
> panel_funcs->prepare(). So, this series shifts the bridge operation
> ealier from bridge_funcs->pre_enable() to bridge_funcs->mode_set().
>
> Patch 3/3 does the essential bridge operation shift.
>
> Patch 1/3 and 2/3 are split from the original single patch in v2 and
> are needed by patch 3/3. This split-up helps clarify changes better.
> The split-up is done in this way:
>
> 1) Patch 1/3 forces a full modeset when crtc_state->active is changed to
> be true(which implies only connector's DPMS is brought out of "Off"
> status, though not necessarily). This makes sure ->mode_set() and
> ->atomic_disable() will be called in pairs.
> 2) Patch 2/3 removes a check on unchanged HS clock rate from ->mode_set(),
> to make sure MIPI DSI controller and PHY are brought up and taken down
> in pairs.
> 3) Patch 3/3 shifts the bridge operation as the last step.
Looks good to me and tested on imx8mq Librem 5 Devkit with
https://lore.kernel.org/linux-arm-kernel/cover.1617968250.git.agx@sigxcpu.org/
on top so
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Cheers,
-- Guido
>
>
> v2->v3:
> * Split the single patch in v2 into 3 patches. (Neil)
>
> v1->v2:
> * Fix a typo in commit message - s/unchange/unchanged/
>
>
> Liu Ying (3):
> drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is
> changed to be true
> drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from
> ->mode_set()
> drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in
> ->mode_set()
>
> drivers/gpu/drm/bridge/nwl-dsi.c | 86 +++++++++++++++++---------------
> 1 file changed, 46 insertions(+), 40 deletions(-)
>
> --
> 2.25.1
>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true
2021-04-23 9:26 ` [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true Liu Ying
2021-04-30 8:35 ` Neil Armstrong
@ 2021-04-30 9:56 ` Robert Foss
2021-04-30 11:45 ` Liu Ying
1 sibling, 1 reply; 13+ messages in thread
From: Robert Foss @ 2021-04-30 9:56 UTC (permalink / raw)
To: Liu Ying
Cc: Jernej Skrabec, Jonas Karlman, David Airlie, agx, Neil Armstrong,
linux-kernel, dri-devel, Andrzej Hajda, Laurent Pinchart,
robert.chiras, linux-imx
[-- Attachment #1.1: Type: text/plain, Size: 6520 bytes --]
Hey Liu,
This patch does not apply on upstream-drm-misc/drm-misc-next. When it
passes local testing & building, I'm ready to merge it.
On Fri, 23 Apr 2021 at 11:42, Liu Ying <victor.liu@nxp.com> wrote:
> This patch replaces ->mode_fixup() with ->atomic_check() so that
> a full modeset can be requested from there when crtc_state->active
> is changed to be true(which implies only connector's DPMS is brought
> out of "Off" status, though not necessarily). Bridge functions are
> added or changed to accommodate the ->atomic_check() callback. That
> full modeset is needed by the up-coming patch which gets MIPI DSI
> controller and PHY ready in ->mode_set(), because it makes sure
> ->mode_set() and ->atomic_disable() are called in pairs.
>
> Cc: Andrzej Hajda <a.hajda@samsung.com>
> Cc: Neil Armstrong <narmstrong@baylibre.com>
> Cc: Robert Foss <robert.foss@linaro.org>
> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
> Cc: Jonas Karlman <jonas@kwiboo.se>
> Cc: Jernej Skrabec <jernej.skrabec@siol.net>
> Cc: David Airlie <airlied@linux.ie>
> Cc: Daniel Vetter <daniel@ffwll.ch>
> Cc: Guido Günther <agx@sigxcpu.org>
> Cc: Robert Chiras <robert.chiras@nxp.com>
> Cc: NXP Linux Team <linux-imx@nxp.com>
> Signed-off-by: Liu Ying <victor.liu@nxp.com>
> ---
> v2->v3:
> * Split from the single patch in v2 to clarify changes. (Neil)
>
> drivers/gpu/drm/bridge/nwl-dsi.c | 61 ++++++++++++++++++++------------
> 1 file changed, 39 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c
> b/drivers/gpu/drm/bridge/nwl-dsi.c
> index 66b67402f1acd..c65ca860712d2 100644
> --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> @@ -21,6 +21,7 @@
> #include <linux/sys_soc.h>
> #include <linux/time64.h>
>
> +#include <drm/drm_atomic_state_helper.h>
> #include <drm/drm_bridge.h>
> #include <drm/drm_mipi_dsi.h>
> #include <drm/drm_of.h>
> @@ -742,7 +743,9 @@ static int nwl_dsi_disable(struct nwl_dsi *dsi)
> return 0;
> }
>
> -static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
> +static void
> +nwl_dsi_bridge_atomic_disable(struct drm_bridge *bridge,
> + struct drm_bridge_state *old_bridge_state)
> {
> struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> int ret;
> @@ -803,17 +806,6 @@ static int nwl_dsi_get_dphy_params(struct nwl_dsi
> *dsi,
> return 0;
> }
>
> -static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
> - const struct drm_display_mode *mode,
> - struct drm_display_mode
> *adjusted_mode)
> -{
> - /* At least LCDIF + NWL needs active high sync */
> - adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC |
> DRM_MODE_FLAG_PVSYNC);
> - adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC |
> DRM_MODE_FLAG_NVSYNC);
> -
> - return true;
> -}
> -
> static enum drm_mode_status
> nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> const struct drm_display_info *info,
> @@ -831,6 +823,24 @@ nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> return MODE_OK;
> }
>
> +static int nwl_dsi_bridge_atomic_check(struct drm_bridge *bridge,
> + struct drm_bridge_state
> *bridge_state,
> + struct drm_crtc_state *crtc_state,
> + struct drm_connector_state
> *conn_state)
> +{
> + struct drm_display_mode *adjusted_mode =
> &crtc_state->adjusted_mode;
> +
> + /* At least LCDIF + NWL needs active high sync */
> + adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC |
> DRM_MODE_FLAG_PVSYNC);
> + adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC |
> DRM_MODE_FLAG_NVSYNC);
> +
> + /* Do a full modeset if crtc_state->active is changed to be true.
> */
> + if (crtc_state->active_changed && crtc_state->active)
> + crtc_state->mode_changed = true;
> +
> + return 0;
> +}
> +
> static void
> nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> const struct drm_display_mode *mode,
> @@ -862,7 +872,9 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> drm_mode_debug_printmodeline(adjusted_mode);
> }
>
> -static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
> +static void
> +nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
> + struct drm_bridge_state *old_bridge_state)
> {
> struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> int ret;
> @@ -897,7 +909,9 @@ static void nwl_dsi_bridge_pre_enable(struct
> drm_bridge *bridge)
> }
> }
>
> -static void nwl_dsi_bridge_enable(struct drm_bridge *bridge)
> +static void
> +nwl_dsi_bridge_atomic_enable(struct drm_bridge *bridge,
> + struct drm_bridge_state *old_bridge_state)
> {
> struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> int ret;
> @@ -942,14 +956,17 @@ static void nwl_dsi_bridge_detach(struct drm_bridge
> *bridge)
> }
>
> static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
> - .pre_enable = nwl_dsi_bridge_pre_enable,
> - .enable = nwl_dsi_bridge_enable,
> - .disable = nwl_dsi_bridge_disable,
> - .mode_fixup = nwl_dsi_bridge_mode_fixup,
> - .mode_set = nwl_dsi_bridge_mode_set,
> - .mode_valid = nwl_dsi_bridge_mode_valid,
> - .attach = nwl_dsi_bridge_attach,
> - .detach = nwl_dsi_bridge_detach,
> + .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
> + .atomic_reset = drm_atomic_helper_bridge_reset,
> + .atomic_check = nwl_dsi_bridge_atomic_check,
> + .atomic_pre_enable = nwl_dsi_bridge_atomic_pre_enable,
> + .atomic_enable = nwl_dsi_bridge_atomic_enable,
> + .atomic_disable = nwl_dsi_bridge_atomic_disable,
> + .mode_set = nwl_dsi_bridge_mode_set,
> + .mode_valid = nwl_dsi_bridge_mode_valid,
> + .attach = nwl_dsi_bridge_attach,
> + .detach = nwl_dsi_bridge_detach,
> };
>
> static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
> --
> 2.25.1
>
>
[-- Attachment #1.2: Type: text/html, Size: 8402 bytes --]
[-- Attachment #2: Type: text/plain, Size: 160 bytes --]
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true
2021-04-30 9:56 ` Robert Foss
@ 2021-04-30 11:45 ` Liu Ying
2021-04-30 11:49 ` Robert Foss
0 siblings, 1 reply; 13+ messages in thread
From: Liu Ying @ 2021-04-30 11:45 UTC (permalink / raw)
To: Robert Foss
Cc: Jernej Skrabec, Jonas Karlman, David Airlie, agx, Neil Armstrong,
linux-kernel, dri-devel, Andrzej Hajda, Laurent Pinchart,
robert.chiras, linux-imx
Hi Robert,
On Fri, 2021-04-30 at 11:56 +0200, Robert Foss wrote:
> Hey Liu,
>
> This patch does not apply on upstream-drm-misc/drm-misc-next. When it
> passes local testing & building, I'm ready to merge it.
I see Neil has already pushed this entire patch series to
drm-misc-next.
https://cgit.freedesktop.org/drm/drm-misc/commit/?id=885811372fe101c4299c53eecc9fee72cf927a0c
I also see Guido's R-b and T-b tags on this series, though they comes
after Neil's push perhaps.
Thanks,
Liu Ying
>
> On Fri, 23 Apr 2021 at 11:42, Liu Ying <victor.liu@nxp.com> wrote:
> > This patch replaces ->mode_fixup() with ->atomic_check() so that
> > a full modeset can be requested from there when crtc_state->active
> > is changed to be true(which implies only connector's DPMS is
> > brought
> > out of "Off" status, though not necessarily). Bridge functions are
> > added or changed to accommodate the ->atomic_check() callback.
> > That
> > full modeset is needed by the up-coming patch which gets MIPI DSI
> > controller and PHY ready in ->mode_set(), because it makes sure
> > ->mode_set() and ->atomic_disable() are called in pairs.
> >
> > Cc: Andrzej Hajda <a.hajda@samsung.com>
> > Cc: Neil Armstrong <narmstrong@baylibre.com>
> > Cc: Robert Foss <robert.foss@linaro.org>
> > Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
> > Cc: Jonas Karlman <jonas@kwiboo.se>
> > Cc: Jernej Skrabec <jernej.skrabec@siol.net>
> > Cc: David Airlie <airlied@linux.ie>
> > Cc: Daniel Vetter <daniel@ffwll.ch>
> > Cc: Guido Günther <agx@sigxcpu.org>
> > Cc: Robert Chiras <robert.chiras@nxp.com>
> > Cc: NXP Linux Team <linux-imx@nxp.com>
> > Signed-off-by: Liu Ying <victor.liu@nxp.com>
> > ---
> > v2->v3:
> > * Split from the single patch in v2 to clarify changes. (Neil)
> >
> > drivers/gpu/drm/bridge/nwl-dsi.c | 61 ++++++++++++++++++++------
> > ------
> > 1 file changed, 39 insertions(+), 22 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c
> > b/drivers/gpu/drm/bridge/nwl-dsi.c
> > index 66b67402f1acd..c65ca860712d2 100644
> > --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> > +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> > @@ -21,6 +21,7 @@
> > #include <linux/sys_soc.h>
> > #include <linux/time64.h>
> >
> > +#include <drm/drm_atomic_state_helper.h>
> > #include <drm/drm_bridge.h>
> > #include <drm/drm_mipi_dsi.h>
> > #include <drm/drm_of.h>
> > @@ -742,7 +743,9 @@ static int nwl_dsi_disable(struct nwl_dsi *dsi)
> > return 0;
> > }
> >
> > -static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
> > +static void
> > +nwl_dsi_bridge_atomic_disable(struct drm_bridge *bridge,
> > + struct drm_bridge_state
> > *old_bridge_state)
> > {
> > struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > int ret;
> > @@ -803,17 +806,6 @@ static int nwl_dsi_get_dphy_params(struct
> > nwl_dsi *dsi,
> > return 0;
> > }
> >
> > -static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
> > - const struct drm_display_mode
> > *mode,
> > - struct drm_display_mode
> > *adjusted_mode)
> > -{
> > - /* At least LCDIF + NWL needs active high sync */
> > - adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC |
> > DRM_MODE_FLAG_PVSYNC);
> > - adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC |
> > DRM_MODE_FLAG_NVSYNC);
> > -
> > - return true;
> > -}
> > -
> > static enum drm_mode_status
> > nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> > const struct drm_display_info *info,
> > @@ -831,6 +823,24 @@ nwl_dsi_bridge_mode_valid(struct drm_bridge
> > *bridge,
> > return MODE_OK;
> > }
> >
> > +static int nwl_dsi_bridge_atomic_check(struct drm_bridge *bridge,
> > + struct drm_bridge_state
> > *bridge_state,
> > + struct drm_crtc_state
> > *crtc_state,
> > + struct drm_connector_state
> > *conn_state)
> > +{
> > + struct drm_display_mode *adjusted_mode = &crtc_state-
> > >adjusted_mode;
> > +
> > + /* At least LCDIF + NWL needs active high sync */
> > + adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC |
> > DRM_MODE_FLAG_PVSYNC);
> > + adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC |
> > DRM_MODE_FLAG_NVSYNC);
> > +
> > + /* Do a full modeset if crtc_state->active is changed to be
> > true. */
> > + if (crtc_state->active_changed && crtc_state->active)
> > + crtc_state->mode_changed = true;
> > +
> > + return 0;
> > +}
> > +
> > static void
> > nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> > const struct drm_display_mode *mode,
> > @@ -862,7 +872,9 @@ nwl_dsi_bridge_mode_set(struct drm_bridge
> > *bridge,
> > drm_mode_debug_printmodeline(adjusted_mode);
> > }
> >
> > -static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
> > +static void
> > +nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
> > + struct drm_bridge_state
> > *old_bridge_state)
> > {
> > struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > int ret;
> > @@ -897,7 +909,9 @@ static void nwl_dsi_bridge_pre_enable(struct
> > drm_bridge *bridge)
> > }
> > }
> >
> > -static void nwl_dsi_bridge_enable(struct drm_bridge *bridge)
> > +static void
> > +nwl_dsi_bridge_atomic_enable(struct drm_bridge *bridge,
> > + struct drm_bridge_state
> > *old_bridge_state)
> > {
> > struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > int ret;
> > @@ -942,14 +956,17 @@ static void nwl_dsi_bridge_detach(struct
> > drm_bridge *bridge)
> > }
> >
> > static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
> > - .pre_enable = nwl_dsi_bridge_pre_enable,
> > - .enable = nwl_dsi_bridge_enable,
> > - .disable = nwl_dsi_bridge_disable,
> > - .mode_fixup = nwl_dsi_bridge_mode_fixup,
> > - .mode_set = nwl_dsi_bridge_mode_set,
> > - .mode_valid = nwl_dsi_bridge_mode_valid,
> > - .attach = nwl_dsi_bridge_attach,
> > - .detach = nwl_dsi_bridge_detach,
> > + .atomic_duplicate_state =
> > drm_atomic_helper_bridge_duplicate_state,
> > + .atomic_destroy_state =
> > drm_atomic_helper_bridge_destroy_state,
> > + .atomic_reset = drm_atomic_helper_bridge_reset,
> > + .atomic_check = nwl_dsi_bridge_atomic_check,
> > + .atomic_pre_enable = nwl_dsi_bridge_atomic_pre_enable,
> > + .atomic_enable = nwl_dsi_bridge_atomic_enable,
> > + .atomic_disable = nwl_dsi_bridge_atomic_disable,
> > + .mode_set = nwl_dsi_bridge_mode_set,
> > + .mode_valid = nwl_dsi_bridge_mode_valid,
> > + .attach = nwl_dsi_bridge_attach,
> > + .detach = nwl_dsi_bridge_detach,
> > };
> >
> > static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true
2021-04-30 11:45 ` Liu Ying
@ 2021-04-30 11:49 ` Robert Foss
0 siblings, 0 replies; 13+ messages in thread
From: Robert Foss @ 2021-04-30 11:49 UTC (permalink / raw)
To: Liu Ying
Cc: Jernej Skrabec, Jonas Karlman, David Airlie, agx, Neil Armstrong,
linux-kernel, dri-devel, Andrzej Hajda, Laurent Pinchart,
robert.chiras, linux-imx
[-- Attachment #1.1: Type: text/plain, Size: 7712 bytes --]
Even better :)
On Fri, Apr 30, 2021, 13:46 Liu Ying <victor.liu@nxp.com> wrote:
> Hi Robert,
>
> On Fri, 2021-04-30 at 11:56 +0200, Robert Foss wrote:
> > Hey Liu,
> >
> > This patch does not apply on upstream-drm-misc/drm-misc-next. When it
> > passes local testing & building, I'm ready to merge it.
>
> I see Neil has already pushed this entire patch series to
> drm-misc-next.
>
>
>
> https://cgit.freedesktop.org/drm/drm-misc/commit/?id=885811372fe101c4299c53eecc9fee72cf927a0c
>
> I also see Guido's R-b and T-b tags on this series, though they comes
> after Neil's push perhaps.
>
> Thanks,
> Liu Ying
>
> >
> > On Fri, 23 Apr 2021 at 11:42, Liu Ying <victor.liu@nxp.com> wrote:
> > > This patch replaces ->mode_fixup() with ->atomic_check() so that
> > > a full modeset can be requested from there when crtc_state->active
> > > is changed to be true(which implies only connector's DPMS is
> > > brought
> > > out of "Off" status, though not necessarily). Bridge functions are
> > > added or changed to accommodate the ->atomic_check() callback.
> > > That
> > > full modeset is needed by the up-coming patch which gets MIPI DSI
> > > controller and PHY ready in ->mode_set(), because it makes sure
> > > ->mode_set() and ->atomic_disable() are called in pairs.
> > >
> > > Cc: Andrzej Hajda <a.hajda@samsung.com>
> > > Cc: Neil Armstrong <narmstrong@baylibre.com>
> > > Cc: Robert Foss <robert.foss@linaro.org>
> > > Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
> > > Cc: Jonas Karlman <jonas@kwiboo.se>
> > > Cc: Jernej Skrabec <jernej.skrabec@siol.net>
> > > Cc: David Airlie <airlied@linux.ie>
> > > Cc: Daniel Vetter <daniel@ffwll.ch>
> > > Cc: Guido Günther <agx@sigxcpu.org>
> > > Cc: Robert Chiras <robert.chiras@nxp.com>
> > > Cc: NXP Linux Team <linux-imx@nxp.com>
> > > Signed-off-by: Liu Ying <victor.liu@nxp.com>
> > > ---
> > > v2->v3:
> > > * Split from the single patch in v2 to clarify changes. (Neil)
> > >
> > > drivers/gpu/drm/bridge/nwl-dsi.c | 61 ++++++++++++++++++++------
> > > ------
> > > 1 file changed, 39 insertions(+), 22 deletions(-)
> > >
> > > diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c
> > > b/drivers/gpu/drm/bridge/nwl-dsi.c
> > > index 66b67402f1acd..c65ca860712d2 100644
> > > --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> > > +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> > > @@ -21,6 +21,7 @@
> > > #include <linux/sys_soc.h>
> > > #include <linux/time64.h>
> > >
> > > +#include <drm/drm_atomic_state_helper.h>
> > > #include <drm/drm_bridge.h>
> > > #include <drm/drm_mipi_dsi.h>
> > > #include <drm/drm_of.h>
> > > @@ -742,7 +743,9 @@ static int nwl_dsi_disable(struct nwl_dsi *dsi)
> > > return 0;
> > > }
> > >
> > > -static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
> > > +static void
> > > +nwl_dsi_bridge_atomic_disable(struct drm_bridge *bridge,
> > > + struct drm_bridge_state
> > > *old_bridge_state)
> > > {
> > > struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > int ret;
> > > @@ -803,17 +806,6 @@ static int nwl_dsi_get_dphy_params(struct
> > > nwl_dsi *dsi,
> > > return 0;
> > > }
> > >
> > > -static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
> > > - const struct drm_display_mode
> > > *mode,
> > > - struct drm_display_mode
> > > *adjusted_mode)
> > > -{
> > > - /* At least LCDIF + NWL needs active high sync */
> > > - adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC |
> > > DRM_MODE_FLAG_PVSYNC);
> > > - adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC |
> > > DRM_MODE_FLAG_NVSYNC);
> > > -
> > > - return true;
> > > -}
> > > -
> > > static enum drm_mode_status
> > > nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> > > const struct drm_display_info *info,
> > > @@ -831,6 +823,24 @@ nwl_dsi_bridge_mode_valid(struct drm_bridge
> > > *bridge,
> > > return MODE_OK;
> > > }
> > >
> > > +static int nwl_dsi_bridge_atomic_check(struct drm_bridge *bridge,
> > > + struct drm_bridge_state
> > > *bridge_state,
> > > + struct drm_crtc_state
> > > *crtc_state,
> > > + struct drm_connector_state
> > > *conn_state)
> > > +{
> > > + struct drm_display_mode *adjusted_mode = &crtc_state-
> > > >adjusted_mode;
> > > +
> > > + /* At least LCDIF + NWL needs active high sync */
> > > + adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC |
> > > DRM_MODE_FLAG_PVSYNC);
> > > + adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC |
> > > DRM_MODE_FLAG_NVSYNC);
> > > +
> > > + /* Do a full modeset if crtc_state->active is changed to be
> > > true. */
> > > + if (crtc_state->active_changed && crtc_state->active)
> > > + crtc_state->mode_changed = true;
> > > +
> > > + return 0;
> > > +}
> > > +
> > > static void
> > > nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> > > const struct drm_display_mode *mode,
> > > @@ -862,7 +872,9 @@ nwl_dsi_bridge_mode_set(struct drm_bridge
> > > *bridge,
> > > drm_mode_debug_printmodeline(adjusted_mode);
> > > }
> > >
> > > -static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
> > > +static void
> > > +nwl_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
> > > + struct drm_bridge_state
> > > *old_bridge_state)
> > > {
> > > struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > int ret;
> > > @@ -897,7 +909,9 @@ static void nwl_dsi_bridge_pre_enable(struct
> > > drm_bridge *bridge)
> > > }
> > > }
> > >
> > > -static void nwl_dsi_bridge_enable(struct drm_bridge *bridge)
> > > +static void
> > > +nwl_dsi_bridge_atomic_enable(struct drm_bridge *bridge,
> > > + struct drm_bridge_state
> > > *old_bridge_state)
> > > {
> > > struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> > > int ret;
> > > @@ -942,14 +956,17 @@ static void nwl_dsi_bridge_detach(struct
> > > drm_bridge *bridge)
> > > }
> > >
> > > static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
> > > - .pre_enable = nwl_dsi_bridge_pre_enable,
> > > - .enable = nwl_dsi_bridge_enable,
> > > - .disable = nwl_dsi_bridge_disable,
> > > - .mode_fixup = nwl_dsi_bridge_mode_fixup,
> > > - .mode_set = nwl_dsi_bridge_mode_set,
> > > - .mode_valid = nwl_dsi_bridge_mode_valid,
> > > - .attach = nwl_dsi_bridge_attach,
> > > - .detach = nwl_dsi_bridge_detach,
> > > + .atomic_duplicate_state =
> > > drm_atomic_helper_bridge_duplicate_state,
> > > + .atomic_destroy_state =
> > > drm_atomic_helper_bridge_destroy_state,
> > > + .atomic_reset = drm_atomic_helper_bridge_reset,
> > > + .atomic_check = nwl_dsi_bridge_atomic_check,
> > > + .atomic_pre_enable = nwl_dsi_bridge_atomic_pre_enable,
> > > + .atomic_enable = nwl_dsi_bridge_atomic_enable,
> > > + .atomic_disable = nwl_dsi_bridge_atomic_disable,
> > > + .mode_set = nwl_dsi_bridge_mode_set,
> > > + .mode_valid = nwl_dsi_bridge_mode_valid,
> > > + .attach = nwl_dsi_bridge_attach,
> > > + .detach = nwl_dsi_bridge_detach,
> > > };
> > >
> > > static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
>
>
[-- Attachment #1.2: Type: text/html, Size: 11168 bytes --]
[-- Attachment #2: Type: text/plain, Size: 160 bytes --]
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2021-04-30 11:50 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-04-23 9:26 [PATCH v3 0/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
2021-04-23 9:26 ` [PATCH v3 1/3] drm/bridge: nwl-dsi: Force a full modeset when crtc_state->active is changed to be true Liu Ying
2021-04-30 8:35 ` Neil Armstrong
2021-04-30 9:56 ` Robert Foss
2021-04-30 11:45 ` Liu Ying
2021-04-30 11:49 ` Robert Foss
2021-04-23 9:26 ` [PATCH v3 2/3] drm/bridge: nwl-dsi: Remove a check on unchanged HS clock rate from ->mode_set() Liu Ying
2021-04-30 8:35 ` Neil Armstrong
2021-04-23 9:26 ` [PATCH v3 3/3] drm/bridge: nwl-dsi: Get MIPI DSI controller and PHY ready in ->mode_set() Liu Ying
2021-04-30 8:35 ` Neil Armstrong
2021-04-26 7:43 ` [PATCH v3 0/3] " Neil Armstrong
2021-04-30 8:35 ` Neil Armstrong
2021-04-30 9:17 ` Guido Günther
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).