driverdev-devel.linuxdriverproject.org archive mirror
 help / color / mirror / Atom feed
From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
To: u.kleine-koenig@pengutronix.de, linux-kernel@vger.kernel.org,
	Thierry Reding <thierry.reding@gmail.com>,
	Lee Jones <lee.jones@linaro.org>
Cc: devel@driverdev.osuosl.org, linux-pwm@vger.kernel.org,
	f.fainelli@gmail.com, devicetree@vger.kernel.org,
	sboyd@kernel.org, gregkh@linuxfoundation.org,
	linus.walleij@linaro.org, dmitry.torokhov@gmail.com,
	linux-gpio@vger.kernel.org, andy.shevchenko@gmail.com,
	bcm-kernel-feedback-list@broadcom.com, wahrenst@gmx.net,
	p.zabel@pengutronix.de, linux-input@vger.kernel.org,
	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
	bgolaszewski@baylibre.com, linux-clk@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-rpi-kernel@lists.infradead.org
Subject: [PATCH v4 11/11] pwm: Add Raspberry Pi Firmware based PWM bus
Date: Thu, 12 Nov 2020 17:36:29 +0100	[thread overview]
Message-ID: <20201112163630.17177-12-nsaenzjulienne@suse.de> (raw)
In-Reply-To: <20201112163630.17177-1-nsaenzjulienne@suse.de>

Adds support to control the PWM bus available in official Raspberry Pi
PoE HAT. Only RPi's co-processor has access to it, so commands have to
be sent through RPi's firmware mailbox interface.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---

Changes since v2:
 - Use devm_rpi_firmware_get()
 - Rename driver
 - Small cleanups

Changes since v1:
 - Use default pwm bindings and get rid of xlate() function
 - Correct spelling errors
 - Correct apply() function
 - Round values
 - Fix divisions in arm32 mode
 - Small cleanups

 drivers/pwm/Kconfig               |   9 ++
 drivers/pwm/Makefile              |   1 +
 drivers/pwm/pwm-raspberrypi-poe.c | 216 ++++++++++++++++++++++++++++++
 3 files changed, 226 insertions(+)
 create mode 100644 drivers/pwm/pwm-raspberrypi-poe.c

diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index b2a87fd7e8fb..3445984a5a50 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -409,6 +409,15 @@ config PWM_PXA
 	  To compile this driver as a module, choose M here: the module
 	  will be called pwm-pxa.
 
+config PWM_RASPBERRYPI_POE
+	tristate "Raspberry Pi Firwmware PoE Hat PWM support"
+	# Make sure not 'y' when RASPBERRYPI_FIRMWARE is 'm'. This can only
+	# happen when COMPILE_TEST=y, hence the added !RASPBERRYPI_FIRMWARE.
+	depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
+	help
+	  Enable Raspberry Pi firmware controller PWM bus used to control the
+	  official RPI PoE hat
+
 config PWM_RCAR
 	tristate "Renesas R-Car PWM support"
 	depends on ARCH_RENESAS || COMPILE_TEST
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 18b89d7fd092..ed28d7bd4c64 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_PWM_MXS)		+= pwm-mxs.o
 obj-$(CONFIG_PWM_OMAP_DMTIMER)	+= pwm-omap-dmtimer.o
 obj-$(CONFIG_PWM_PCA9685)	+= pwm-pca9685.o
 obj-$(CONFIG_PWM_PXA)		+= pwm-pxa.o
+obj-$(CONFIG_PWM_RASPBERRYPI_POE)	+= pwm-raspberrypi-poe.o
 obj-$(CONFIG_PWM_RCAR)		+= pwm-rcar.o
 obj-$(CONFIG_PWM_RENESAS_TPU)	+= pwm-renesas-tpu.o
 obj-$(CONFIG_PWM_ROCKCHIP)	+= pwm-rockchip.o
diff --git a/drivers/pwm/pwm-raspberrypi-poe.c b/drivers/pwm/pwm-raspberrypi-poe.c
new file mode 100644
index 000000000000..91cd826a36f3
--- /dev/null
+++ b/drivers/pwm/pwm-raspberrypi-poe.c
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2020 Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
+ * For more information on Raspberry Pi's PoE hat see:
+ * https://www.raspberrypi.org/products/poe-hat/
+ *
+ * Limitations:
+ *  - No disable bit, so a disabled PWM is simulated by duty_cycle 0
+ *  - Only normal polarity
+ *  - Fixed 12.5 kHz period
+ *
+ * The current period is completed when HW is reconfigured.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+
+#include <soc/bcm2835/raspberrypi-firmware.h>
+#include <dt-bindings/pwm/raspberrypi,firmware-pwm.h>
+
+#define RPI_PWM_MAX_DUTY		255
+#define RPI_PWM_PERIOD_NS		80000 /* 12.5 kHz */
+
+#define RPI_PWM_CUR_DUTY_REG		0x0
+#define RPI_PWM_DEF_DUTY_REG		0x1
+
+struct raspberrypi_pwm {
+	struct rpi_firmware *firmware;
+	struct pwm_chip chip;
+	unsigned int duty_cycle;
+};
+
+struct raspberrypi_pwm_prop {
+	__le32 reg;
+	__le32 val;
+	__le32 ret;
+} __packed;
+
+static inline struct raspberrypi_pwm *to_raspberrypi_pwm(struct pwm_chip *chip)
+{
+	return container_of(chip, struct raspberrypi_pwm, chip);
+}
+
+static int raspberrypi_pwm_set_property(struct rpi_firmware *firmware,
+					u32 reg, u32 val)
+{
+	struct raspberrypi_pwm_prop msg = {
+		.reg = cpu_to_le32(reg),
+		.val = cpu_to_le32(val),
+	};
+	int ret;
+
+	ret = rpi_firmware_property(firmware, RPI_FIRMWARE_SET_POE_HAT_VAL,
+				    &msg, sizeof(msg));
+	if (ret)
+		return ret;
+	if (msg.ret)
+		return -EIO;
+
+	return 0;
+}
+
+static int raspberrypi_pwm_get_property(struct rpi_firmware *firmware,
+					u32 reg, u32 *val)
+{
+	struct raspberrypi_pwm_prop msg = {
+		.reg = reg
+	};
+	int ret;
+
+	ret = rpi_firmware_property(firmware, RPI_FIRMWARE_GET_POE_HAT_VAL,
+				    &msg, sizeof(msg));
+	if (ret)
+		return ret;
+	if (msg.ret)
+		return -EIO;
+
+	*val = le32_to_cpu(msg.val);
+
+	return 0;
+}
+
+static void raspberrypi_pwm_get_state(struct pwm_chip *chip,
+				      struct pwm_device *pwm,
+				      struct pwm_state *state)
+{
+	struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
+
+	state->period = RPI_PWM_PERIOD_NS;
+	state->duty_cycle = DIV_ROUND_CLOSEST(rpipwm->duty_cycle * RPI_PWM_PERIOD_NS,
+					      RPI_PWM_MAX_DUTY);
+	state->enabled = !!(rpipwm->duty_cycle);
+	state->polarity = PWM_POLARITY_NORMAL;
+}
+
+static int raspberrypi_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+			         const struct pwm_state *state)
+{
+	struct raspberrypi_pwm *rpipwm = to_raspberrypi_pwm(chip);
+	unsigned int duty_cycle;
+	int ret;
+
+        if (state->period < RPI_PWM_PERIOD_NS ||
+            state->polarity != PWM_POLARITY_NORMAL)
+                return -EINVAL;
+
+        if (!state->enabled)
+                duty_cycle = 0;
+        else if (state->duty_cycle < RPI_PWM_PERIOD_NS)
+                duty_cycle = DIV_ROUND_CLOSEST_ULL(state->duty_cycle * RPI_PWM_MAX_DUTY,
+					           RPI_PWM_PERIOD_NS);
+        else
+                duty_cycle = RPI_PWM_MAX_DUTY;
+
+	if (duty_cycle == rpipwm->duty_cycle)
+		return 0;
+
+	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
+					   duty_cycle);
+	if (ret) {
+		dev_err(chip->dev, "Failed to set duty cycle: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * This sets the default duty cycle after resetting the board, we
+	 * updated it every time to mimic Raspberry Pi's downstream's driver
+	 * behaviour.
+	 */
+	ret = raspberrypi_pwm_set_property(rpipwm->firmware, RPI_PWM_DEF_DUTY_REG,
+					   duty_cycle);
+	if (ret) {
+		dev_err(chip->dev, "Failed to set default duty cycle: %d\n", ret);
+		return ret;
+	}
+
+        rpipwm->duty_cycle = duty_cycle;
+
+	return 0;
+}
+
+static const struct pwm_ops raspberrypi_pwm_ops = {
+	.get_state = raspberrypi_pwm_get_state,
+	.apply = raspberrypi_pwm_apply,
+	.owner = THIS_MODULE,
+};
+
+static int raspberrypi_pwm_probe(struct platform_device *pdev)
+{
+	struct device_node *firmware_node;
+	struct device *dev = &pdev->dev;
+	struct rpi_firmware *firmware;
+	struct raspberrypi_pwm *rpipwm;
+	int ret;
+
+	firmware_node = of_get_parent(dev->of_node);
+	if (!firmware_node) {
+		dev_err(dev, "Missing firmware node\n");
+		return -ENOENT;
+	}
+
+	firmware = devm_rpi_firmware_get(&pdev->dev, firmware_node);
+	of_node_put(firmware_node);
+	if (!firmware)
+		return -EPROBE_DEFER;
+
+	rpipwm = devm_kzalloc(&pdev->dev, sizeof(*rpipwm), GFP_KERNEL);
+	if (!rpipwm)
+		return -ENOMEM;
+
+	rpipwm->firmware = firmware;
+	rpipwm->chip.dev = dev;
+	rpipwm->chip.ops = &raspberrypi_pwm_ops;
+	rpipwm->chip.base = -1;
+	rpipwm->chip.npwm = RASPBERRYPI_FIRMWARE_PWM_NUM;
+
+	platform_set_drvdata(pdev, rpipwm);
+
+	ret = raspberrypi_pwm_get_property(rpipwm->firmware, RPI_PWM_CUR_DUTY_REG,
+					   &rpipwm->duty_cycle);
+	if (ret) {
+		dev_err(dev, "Failed to get duty cycle: %d\n", ret);
+		return ret;
+	}
+
+	return pwmchip_add(&rpipwm->chip);
+}
+
+static int raspberrypi_pwm_remove(struct platform_device *pdev)
+{
+	struct raspberrypi_pwm *rpipwm = platform_get_drvdata(pdev);
+
+	return pwmchip_remove(&rpipwm->chip);
+}
+
+static const struct of_device_id raspberrypi_pwm_of_match[] = {
+	{ .compatible = "raspberrypi,firmware-pwm", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, raspberrypi_pwm_of_match);
+
+static struct platform_driver raspberrypi_pwm_driver = {
+	.driver = {
+		.name = "raspberrypi-pwm",
+		.of_match_table = raspberrypi_pwm_of_match,
+	},
+	.probe = raspberrypi_pwm_probe,
+	.remove = raspberrypi_pwm_remove,
+};
+module_platform_driver(raspberrypi_pwm_driver);
+
+MODULE_AUTHOR("Nicolas Saenz Julienne <nsaenzjulienne@suse.de>");
+MODULE_DESCRIPTION("Raspberry Pi Firwmare Based PWM Bus Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.29.2

_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

      parent reply	other threads:[~2020-11-12 16:45 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-11-12 16:36 [PATCH v4 00/11] Raspberry Pi PoE HAT fan support Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 01/11] firmware: raspberrypi: Keep count of all consumers Nicolas Saenz Julienne
2020-11-12 17:52   ` Andy Shevchenko
2020-11-13  7:26     ` Dmitry Torokhov
2020-11-23 17:19       ` Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 02/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get() Nicolas Saenz Julienne
2020-11-12 17:25   ` Bartosz Golaszewski
2020-11-13  9:21     ` Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 03/11] clk: bcm: rpi: Release firmware handle on unbind Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 04/11] gpio: raspberrypi-exp: " Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 05/11] reset: raspberrypi: " Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 06/11] soc: bcm: raspberrypi-power: " Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 07/11] staging: vchiq: " Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 08/11] input: raspberrypi-ts: Release firmware handle when not needed Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 09/11] dt-bindings: pwm: Add binding for RPi firmware PWM bus Nicolas Saenz Julienne
2020-11-12 16:36 ` [PATCH v4 10/11] DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support Nicolas Saenz Julienne
2020-11-12 16:36 ` Nicolas Saenz Julienne [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201112163630.17177-12-nsaenzjulienne@suse.de \
    --to=nsaenzjulienne@suse.de \
    --cc=andy.shevchenko@gmail.com \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=devel@driverdev.osuosl.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dmitry.torokhov@gmail.com \
    --cc=f.fainelli@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=lee.jones@linaro.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-input@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pwm@vger.kernel.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=p.zabel@pengutronix.de \
    --cc=sboyd@kernel.org \
    --cc=thierry.reding@gmail.com \
    --cc=u.kleine-koenig@pengutronix.de \
    --cc=wahrenst@gmx.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).