* [PATCH v4 2/2] drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP bridge driver
2019-11-08 8:58 [PATCH v3 0/2] Add initial support for slimport anx7625 Xin Ji
2019-11-08 8:59 ` [PATCH v4 1/2] dt-bindings: drm/bridge: anx7625: MIPI to DP transmitter binding Xin Ji
@ 2019-11-08 9:00 ` Xin Ji
1 sibling, 0 replies; 3+ messages in thread
From: Xin Ji @ 2019-11-08 9:00 UTC (permalink / raw)
To: devel, Laurent Pinchart, Andrzej Hajda
Cc: Jernej Skrabec, Nicolas Boichat, Pi-Hsun Shih, Jonas Karlman,
David Airlie, Neil Armstrong, linux-kernel, dri-devel, Sheng Pan,
Daniel Vetter, Dan Carpenter
The ANX7625 is an ultra-low power 4K Mobile HD Transmitter designed
for portable device. It converts MIPI DSI/DPI to DisplayPort 1.3 4K.
The ANX7625 can support both USB Type-C PD feature and MIPI DSI/DPI
to DP feature. This driver only enabled MIPI DSI/DPI to DP feature.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
---
drivers/gpu/drm/bridge/Makefile | 2 +-
drivers/gpu/drm/bridge/analogix/Kconfig | 6 +
drivers/gpu/drm/bridge/analogix/Makefile | 1 +
drivers/gpu/drm/bridge/analogix/anx7625.c | 2042 +++++++++++++++++++++++++++++
drivers/gpu/drm/bridge/analogix/anx7625.h | 406 ++++++
5 files changed, 2456 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.c
create mode 100644 drivers/gpu/drm/bridge/analogix/anx7625.h
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 4934fcf..bcd388a 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -12,8 +12,8 @@ obj-$(CONFIG_DRM_SII9234) += sii9234.o
obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
-obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
+obj-y += analogix/
obj-y += synopsys/
diff --git a/drivers/gpu/drm/bridge/analogix/Kconfig b/drivers/gpu/drm/bridge/analogix/Kconfig
index e930ff9..b2f127e 100644
--- a/drivers/gpu/drm/bridge/analogix/Kconfig
+++ b/drivers/gpu/drm/bridge/analogix/Kconfig
@@ -2,3 +2,9 @@
config DRM_ANALOGIX_DP
tristate
depends on DRM
+
+config ANALOGIX_ANX7625
+ tristate "Analogix MIPI to DP interface support"
+ help
+ ANX7625 is an ultra-low power 4K mobile HD transmitter designed
+ for portable devices. It converts MIPI/DPI to DisplayPort1.3 4K.
diff --git a/drivers/gpu/drm/bridge/analogix/Makefile b/drivers/gpu/drm/bridge/analogix/Makefile
index fdbf3fd..8a52867 100644
--- a/drivers/gpu/drm/bridge/analogix/Makefile
+++ b/drivers/gpu/drm/bridge/analogix/Makefile
@@ -1,3 +1,4 @@
# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_ANALOGIX_ANX7625) += anx7625.o
analogix_dp-objs := analogix_dp_core.o analogix_dp_reg.o
obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix_dp.o
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
new file mode 100644
index 0000000..ad73317
--- /dev/null
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -0,0 +1,2042 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright(c) 2016, Analogix Semiconductor. All rights reserved.
+ *
+ */
+#include <linux/extcon.h>
+#include <linux/gcd.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/workqueue.h>
+
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/of_platform.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_dp_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+#include <video/display_timing.h>
+
+#include "anx7625.h"
+
+/*
+ * there is a sync issue while access I2C register between AP(CPU) and
+ * internal firmware(OCM), to avoid the race condition, AP should access
+ * the reserved slave address before slave address occurs changes.
+ */
+static int i2c_access_workaround(struct anx7625_data *ctx,
+ struct i2c_client *client)
+{
+ u8 offset;
+ struct device *dev = &client->dev;
+ int ret;
+
+ if (client == ctx->last_client)
+ return 0;
+
+ ctx->last_client = client;
+
+ if (client == ctx->i2c.tcpc_client)
+ offset = RSVD_00_ADDR;
+ else if (client == ctx->i2c.tx_p0_client)
+ offset = RSVD_D1_ADDR;
+ else if (client == ctx->i2c.tx_p1_client)
+ offset = RSVD_60_ADDR;
+ else if (client == ctx->i2c.rx_p0_client)
+ offset = RSVD_39_ADDR;
+ else if (client == ctx->i2c.rx_p1_client)
+ offset = RSVD_7F_ADDR;
+ else
+ offset = RSVD_00_ADDR;
+
+ ret = i2c_smbus_write_byte_data(client, offset, 0x00);
+ if (ret < 0)
+ DRM_DEV_ERROR(dev,
+ "failed to access i2c id=%x\n:%x",
+ client->addr, offset);
+
+ return ret;
+}
+
+static int anx7625_reg_read(struct anx7625_data *ctx,
+ struct i2c_client *client, u8 reg_addr)
+{
+ int ret;
+ struct device *dev = &client->dev;
+
+ i2c_access_workaround(ctx, client);
+
+ ret = i2c_smbus_read_byte_data(client, reg_addr);
+ if (ret < 0)
+ DRM_DEV_ERROR(dev, "read i2c failed id=%x:%x\n",
+ client->addr, reg_addr);
+
+ return ret;
+}
+
+static int anx7625_reg_block_read(struct anx7625_data *ctx,
+ struct i2c_client *client,
+ u8 reg_addr, u8 len, u8 *buf)
+{
+ int ret;
+ struct device *dev = &client->dev;
+
+ i2c_access_workaround(ctx, client);
+
+ ret = i2c_smbus_read_i2c_block_data(client, reg_addr, len, buf);
+ if (ret < 0)
+ DRM_DEV_ERROR(dev, "read i2c block failed id=%x:%x\n",
+ client->addr, reg_addr);
+
+ return ret;
+}
+
+static int anx7625_reg_write(struct anx7625_data *ctx,
+ struct i2c_client *client,
+ u8 reg_addr, u8 reg_val)
+{
+ int ret;
+ struct device *dev = &client->dev;
+
+ i2c_access_workaround(ctx, client);
+
+ ret = i2c_smbus_write_byte_data(client, reg_addr, reg_val);
+
+ if (ret < 0)
+ DRM_DEV_ERROR(dev, "failed to write i2c id=%x\n:%x",
+ client->addr, reg_addr);
+
+ return ret;
+}
+
+static int anx7625_write_or(struct anx7625_data *ctx,
+ struct i2c_client *client,
+ u8 offset, u8 mask)
+{
+ int val;
+
+ val = anx7625_reg_read(ctx, client, offset);
+ if (val < 0)
+ return val;
+
+ return anx7625_reg_write(ctx, client, offset, (val | (mask)));
+}
+
+static int anx7625_write_and(struct anx7625_data *ctx,
+ struct i2c_client *client,
+ u8 offset, u8 mask)
+{
+ int val;
+
+ val = anx7625_reg_read(ctx, client, offset);
+ if (val < 0)
+ return val;
+
+ return anx7625_reg_write(ctx, client, offset, (val & (mask)));
+}
+
+static int anx7625_write_and_or(struct anx7625_data *ctx,
+ struct i2c_client *client,
+ u8 offset, u8 and_mask, u8 or_mask)
+{
+ int val;
+
+ val = anx7625_reg_read(ctx, client, offset);
+ if (val < 0)
+ return val;
+
+ return anx7625_reg_write(ctx, client,
+ offset, (val & and_mask) | (or_mask));
+}
+
+static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
+{
+ int i, ret;
+
+ ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ AUDIO_CONTROL_REGISTER, 0x80);
+ for (i = 0; i < 13; i++)
+ ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ VIDEO_BIT_MATRIX_12 + i,
+ 0x18 + i);
+
+ return ret;
+}
+
+static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx)
+{
+ return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS);
+}
+
+static int wait_aux_op_finish(struct anx7625_data *ctx)
+{
+ int val;
+ int ret;
+ struct device *dev = &ctx->client->dev;
+
+ ret = readx_poll_timeout(anx7625_read_ctrl_status_p0,
+ ctx, val,
+ (!(val & AP_AUX_CTRL_OP_EN) || (val < 0)),
+ 2000,
+ 2000 * 150);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "aux operation failed!\n");
+ return -EIO;
+ }
+
+ val = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_CTRL_STATUS);
+ if (val < 0 || (val & 0x0F)) {
+ DRM_DEV_ERROR(dev, "aux status %02x\n", val);
+ val = -EIO;
+ }
+
+ return val;
+}
+
+static int anx7625_video_mute_control(struct anx7625_data *ctx,
+ u8 status)
+{
+ int ret;
+
+ if (status) { /* mute on */
+ /* set mute flag */
+ ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, AP_MIPI_MUTE);
+ /* clear mipi RX en */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, (u8)~AP_MIPI_RX_EN);
+ } else { /* mute off */
+ /* clear mute flag */
+ ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+ /* set MIPI RX EN */
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, AP_MIPI_RX_EN);
+ }
+
+ return ret;
+}
+
+static int anx7625_config_audio_input(struct anx7625_data *ctx)
+{
+ int ret;
+
+ /* channel num */
+ ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5);
+ /* layout */
+ /* as I2S channel is 2, no need to set layout */
+
+ /* FS */
+ ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+ AUDIO_CHANNEL_STATUS_4,
+ 0xf0, AUDIO_FS_48K);
+ /* word length */
+ ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
+ AUDIO_CHANNEL_STATUS_5,
+ 0xf0, AUDIO_W_LEN_24_24MAX);
+ /* I2S */
+ ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
+ AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE);
+ ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client,
+ AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE);
+ /* audio change flag */
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, AP_AUDIO_CHG);
+
+ if (ret < 0)
+ DRM_ERROR("failed to config audio.\n");
+
+ return ret;
+}
+
+/* reduction of fraction a/b */
+static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b)
+{
+ unsigned long gcd_num;
+ unsigned long tmp_a, tmp_b;
+ u32 i = 1;
+
+ gcd_num = gcd(*a, *b);
+ *a /= gcd_num;
+ *b /= gcd_num;
+
+ tmp_a = *a;
+ tmp_b = *b;
+
+ while ((*a > MAX_UNSIGNED_24BIT) || (*b > MAX_UNSIGNED_24BIT)) {
+ i++;
+ *a = tmp_a / i;
+ *b = tmp_b / i;
+ }
+
+ /*
+ * in the end, make a, b larger to have higher ODFC PLL
+ * output frequency accuracy
+ */
+ while ((*a < MAX_UNSIGNED_24BIT) && (*b < MAX_UNSIGNED_24BIT)) {
+ *a <<= 1;
+ *b <<= 1;
+ }
+
+ *a >>= 1;
+ *b >>= 1;
+}
+
+static int anx7625_calculate_m_n(u32 pixelclock,
+ unsigned long *m,
+ unsigned long *n,
+ u8 *post_divider)
+{
+ if (pixelclock > PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN) {
+ /* pixel clock frequency is too high */
+ DRM_ERROR("pixelclock too high, act(%d), maximum(%lu)\n",
+ pixelclock,
+ PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN);
+ return -EINVAL;
+ }
+
+ if (pixelclock < PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX) {
+ /* pixel clock frequency is too low */
+ DRM_ERROR("pixelclock too low, act(%d), maximum(%lu)\n",
+ pixelclock,
+ PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX);
+ return -EINVAL;
+ }
+
+ for (*post_divider = 1;
+ pixelclock < (PLL_OUT_FREQ_MIN / (*post_divider));)
+ *post_divider += 1;
+
+ if (*post_divider > POST_DIVIDER_MAX) {
+ for (*post_divider = 1;
+ (pixelclock <
+ (PLL_OUT_FREQ_ABS_MIN / (*post_divider)));)
+ *post_divider += 1;
+
+ if (*post_divider > POST_DIVIDER_MAX) {
+ DRM_ERROR("cannot find property post_divider(%d)\n",
+ *post_divider);
+ return -EDOM;
+ }
+ }
+
+ /* patch to improve the accuracy */
+ if (*post_divider == 7) {
+ /* 27,000,000 is not divisible by 7 */
+ *post_divider = 8;
+ } else if (*post_divider == 11) {
+ /* 27,000,000 is not divisible by 11 */
+ *post_divider = 12;
+ } else if ((*post_divider == 13) || (*post_divider == 14)) {
+ /*27,000,000 is not divisible by 13 or 14*/
+ *post_divider = 15;
+ }
+
+ if (pixelclock * (*post_divider) > PLL_OUT_FREQ_ABS_MAX) {
+ DRM_ERROR("act clock(%u) large than maximum(%lu)\n",
+ pixelclock * (*post_divider),
+ PLL_OUT_FREQ_ABS_MAX);
+ return -EDOM;
+ }
+
+ *m = pixelclock;
+ *n = XTAL_FRQ / (*post_divider);
+
+ anx7625_reduction_of_a_fraction(m, n);
+
+ return 0;
+}
+
+static int anx7625_odfc_config(struct anx7625_data *ctx,
+ u8 post_divider)
+{
+ int ret;
+
+ /* config input reference clock frequency 27MHz/19.2MHz */
+ ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16,
+ ~(REF_CLK_27000KHZ << MIPI_FREF_D_IND));
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16,
+ (REF_CLK_27000KHZ << MIPI_FREF_D_IND));
+ /* post divider */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+ MIPI_DIGITAL_PLL_8, 0x0f);
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_8,
+ post_divider << 4);
+
+ /* add patch for MIS2-125 (5pcs ANX7625 fail ATE MBIST test) */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+ ~MIPI_PLL_VCO_TUNE_REG_VAL);
+
+ /* reset ODFC PLL */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+ ~MIPI_PLL_RESET_N);
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7,
+ MIPI_PLL_RESET_N);
+
+ if (ret < 0)
+ DRM_ERROR("IO error.\n");
+
+ return ret;
+}
+
+static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ unsigned long m, n;
+ u16 htotal;
+ int ret;
+ u8 post_divider = 0;
+
+ ret = anx7625_calculate_m_n(ctx->dt.pixelclock.min * 1000,
+ &m, &n, &post_divider);
+
+ if (ret) {
+ DRM_ERROR("cannot get property m n value.\n");
+ return ret;
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, "compute M(%lu), N(%lu), divider(%d).\n",
+ m, n, post_divider);
+
+ /* configure pixel clock */
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_L,
+ (ctx->dt.pixelclock.min / 1000) & 0xFF);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_H,
+ (ctx->dt.pixelclock.min / 1000) >> 8);
+ /* lane count */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+ MIPI_LANE_CTRL_0, 0xfc);
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client,
+ MIPI_LANE_CTRL_0, 3);
+
+ /* Htotal */
+ htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min +
+ ctx->dt.hback_porch.min + ctx->dt.hsync_len.min;
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_TOTAL_PIXELS_L, htotal & 0xFF);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_TOTAL_PIXELS_H, htotal >> 8);
+ /* Hactive */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_ACTIVE_PIXELS_L, ctx->dt.hactive.min & 0xFF);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_ACTIVE_PIXELS_H, ctx->dt.hactive.min >> 8);
+ /* HFP */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_FRONT_PORCH_L, ctx->dt.hfront_porch.min);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_FRONT_PORCH_H,
+ ctx->dt.hfront_porch.min >> 8);
+ /* HWS */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_SYNC_WIDTH_L, ctx->dt.hsync_len.min);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_SYNC_WIDTH_H, ctx->dt.hsync_len.min >> 8);
+ /* HBP */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_BACK_PORCH_L, ctx->dt.hback_porch.min);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ HORIZONTAL_BACK_PORCH_H, ctx->dt.hback_porch.min >> 8);
+ /* Vactive */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_L,
+ ctx->dt.vactive.min);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_H,
+ ctx->dt.vactive.min >> 8);
+ /* VFP */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ VERTICAL_FRONT_PORCH, ctx->dt.vfront_porch.min);
+ /* VWS */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ VERTICAL_SYNC_WIDTH, ctx->dt.vsync_len.min);
+ /* VBP */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client,
+ VERTICAL_BACK_PORCH, ctx->dt.vback_porch.min);
+ /* M value */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_PLL_M_NUM_23_16, (m >> 16) & 0xff);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_PLL_M_NUM_15_8, (m >> 8) & 0xff);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_PLL_M_NUM_7_0, (m & 0xff));
+ /* N value */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_PLL_N_NUM_23_16, (n >> 16) & 0xff);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_PLL_N_NUM_15_8, (n >> 8) & 0xff);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_PLL_N_NUM_7_0,
+ (n & 0xff));
+ /* diff */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_DIGITAL_ADJ_1, 0x37);
+
+ ret |= anx7625_odfc_config(ctx, post_divider - 1);
+
+ if (ret < 0)
+ DRM_ERROR("mipi dsi setup IO error.\n");
+
+ return ret;
+}
+
+static int anx7625_swap_dsi_lane3(struct anx7625_data *ctx)
+{
+ int val;
+
+ /* swap MIPI-DSI data lane 3 P and N */
+ val = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP);
+ if (val < 0) {
+ DRM_ERROR("IO error : access MIPI_SWAP.\n");
+ return -EIO;
+ }
+
+ val |= (1 << MIPI_SWAP_CH3);
+ return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP, val);
+}
+
+static int anx7625_api_dsi_config(struct anx7625_data *ctx)
+
+{
+ int val, ret;
+
+ /* swap MIPI-DSI data lane 3 P and N */
+ ret = anx7625_swap_dsi_lane3(ctx);
+ if (ret < 0) {
+ DRM_ERROR("IO error : swap dsi lane 3 failed.\n");
+ return ret;
+ }
+
+ /* DSI clock settings */
+ val = (0 << MIPI_HS_PWD_CLK) |
+ (0 << MIPI_HS_RT_CLK) |
+ (0 << MIPI_PD_CLK) |
+ (1 << MIPI_CLK_RT_MANUAL_PD_EN) |
+ (1 << MIPI_CLK_HS_MANUAL_PD_EN) |
+ (0 << MIPI_CLK_DET_DET_BYPASS) |
+ (0 << MIPI_CLK_MISS_CTRL) |
+ (0 << MIPI_PD_LPTX_CH_MANUAL_PD_EN);
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_PHY_CONTROL_3, val);
+
+ /*
+ * Decreased HS prepare timing delay from 160ns to 80ns work with
+ * a) Dragon board 810 series (Qualcomm AP)
+ * b) Moving Pixel DSI source (PG3A pattern generator +
+ * P332 D-PHY Probe) default D-PHY timing
+ * 5ns/step
+ */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_TIME_HS_PRPR, 0x10);
+
+ /* enable DSI mode*/
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_18,
+ SELECT_DSI << MIPI_DPI_SELECT);
+
+ ret |= anx7625_dsi_video_timing_config(ctx);
+ if (ret < 0) {
+ DRM_ERROR("dsi video timing config failed\n");
+ return ret;
+ }
+
+ /* toggle m, n ready */
+ ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6,
+ ~(MIPI_M_NUM_READY | MIPI_N_NUM_READY));
+ usleep_range(1000, 1100);
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6,
+ MIPI_M_NUM_READY | MIPI_N_NUM_READY);
+
+ /* configure integer stable register */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_VIDEO_STABLE_CNT, 0x02);
+ /* power on MIPI RX */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_LANE_CTRL_10, 0x00);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_LANE_CTRL_10, 0x80);
+
+ if (ret < 0)
+ DRM_ERROR("IO error : mipi dsi enable init failed.\n");
+
+ return ret;
+}
+
+static int anx7625_dsi_config(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "config dsi.\n");
+
+ /* DSC disable */
+ ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ R_DSC_CTRL_0, ~DSC_EN);
+
+ ret |= anx7625_api_dsi_config(ctx);
+
+ if (ret < 0) {
+ DRM_ERROR("IO error : api dsi config error.\n");
+ return ret;
+ }
+
+ /* set MIPI RX EN */
+ ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, AP_MIPI_RX_EN);
+ /* clear mute flag */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+ if (ret < 0)
+ DRM_ERROR("IO error : enable mipi rx failed.\n");
+ else
+ DRM_DEV_DEBUG_DRIVER(dev, "success to config DSI\n");
+
+ return ret;
+}
+
+static int anx7625_api_dpi_config(struct anx7625_data *ctx)
+{
+ u16 freq = ctx->dt.pixelclock.min / 1000;
+ int ret;
+
+ /* configure pixel clock */
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ PIXEL_CLOCK_L, freq & 0xFF);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ PIXEL_CLOCK_H, (freq >> 8));
+
+ /* set DPI mode */
+ /* set to DPI PLL module sel */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_DIGITAL_PLL_9, 0x20);
+ /* power down MIPI */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_LANE_CTRL_10, 0x08);
+ /* enable DPI mode */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+ MIPI_DIGITAL_PLL_18, 0x1C);
+ /* set first edge */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ VIDEO_CONTROL_0, 0x05);
+ if (ret < 0)
+ DRM_ERROR("IO error : dpi phy set failed.\n");
+
+ return ret;
+}
+
+static int anx7625_dpi_config(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n");
+
+ /* DSC disable */
+ ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ R_DSC_CTRL_0, ~DSC_EN);
+ if (ret < 0) {
+ DRM_ERROR("IO error : disable dsc failed.\n");
+ return ret;
+ }
+
+ ret = anx7625_config_bit_matrix(ctx);
+ if (ret < 0) {
+ DRM_ERROR("config bit matrix failed.\n");
+ return ret;
+ }
+
+ ret = anx7625_api_dpi_config(ctx);
+ if (ret < 0) {
+ DRM_ERROR("mipi phy(dpi) setup failed.\n");
+ return ret;
+ }
+
+ /* set MIPI RX EN */
+ ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, AP_MIPI_RX_EN);
+ /* clear mute flag */
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+ if (ret < 0)
+ DRM_ERROR("IO error : enable mipi rx failed.\n");
+
+ return ret;
+}
+
+static void anx7625_dp_start(struct anx7625_data *ctx)
+{
+ int ret;
+
+ if (!ctx->display_timing_valid) {
+ DRM_ERROR("mipi drm haven't set display timing yet.\n");
+ return;
+ }
+
+ anx7625_config_audio_input(ctx);
+
+ if (ctx->pdata.dsi_supported)
+ ret = anx7625_dsi_config(ctx);
+ else
+ ret = anx7625_dpi_config(ctx);
+
+ if (ret < 0)
+ DRM_ERROR("MIPI phy setup error.\n");
+}
+
+static void anx7625_dp_stop(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "stop dp output\n");
+
+ /*
+ * video disable: 0x72:08 bit 7 = 0;
+ * audio disable: 0x70:87 bit 0 = 0;
+ */
+ ret = anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 0x87, 0xfe);
+ ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 0x08, 0x7f);
+
+ ret |= anx7625_video_mute_control(ctx, 1);
+ if (ret < 0)
+ DRM_ERROR("IO error : mute video failed\n");
+}
+
+static int sp_tx_rst_aux(struct anx7625_data *ctx)
+{
+ int ret;
+
+ ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, RST_CTRL2,
+ AUX_RST);
+ ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, RST_CTRL2,
+ ~AUX_RST);
+ return ret;
+}
+
+static int sp_tx_aux_wr(struct anx7625_data *ctx, u8 offset)
+{
+ int ret;
+
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_BUFF_START, offset);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_COMMAND, 0x04);
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+ return (ret | wait_aux_op_finish(ctx));
+}
+
+static int sp_tx_aux_rd(struct anx7625_data *ctx, u8 len_cmd)
+{
+ int ret;
+
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_COMMAND, len_cmd);
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+ return (ret | wait_aux_op_finish(ctx));
+}
+
+static int sp_tx_get_edid_block(struct anx7625_data *ctx)
+{
+ int c = 0;
+ struct device *dev = &ctx->client->dev;
+
+ sp_tx_aux_wr(ctx, 0x7e);
+ sp_tx_aux_rd(ctx, 0x01);
+ c = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_BUFF_START);
+ if (c < 0) {
+ DRM_ERROR("IO error : access AUX BUFF.\n");
+ return -EIO;
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, " EDID Block = %d\n", c + 1);
+
+ if (c > MAX_EDID_BLOCK)
+ c = 1;
+
+ return c;
+}
+
+static int edid_read(struct anx7625_data *ctx,
+ u8 offset, u8 *pblock_buf)
+{
+ int ret, cnt;
+ struct device *dev = &ctx->client->dev;
+
+ for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) {
+ sp_tx_aux_wr(ctx, offset);
+ /* set I2C read com 0x01 mot = 0 and read 16 bytes */
+ ret = sp_tx_aux_rd(ctx, 0xf1);
+
+ if (ret) {
+ sp_tx_rst_aux(ctx);
+ DRM_DEV_DEBUG_DRIVER(dev, "edid read failed, reset!\n");
+ } else {
+ ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_BUFF_START,
+ MAX_DPCD_BUFFER_SIZE,
+ pblock_buf);
+ if (ret > 0)
+ break;
+ }
+ }
+
+ if (cnt > EDID_TRY_CNT)
+ return -EIO;
+
+ return 0;
+}
+
+static int segments_edid_read(struct anx7625_data *ctx,
+ u8 segment, u8 *buf, u8 offset)
+{
+ u8 cnt;
+ int ret;
+ struct device *dev = &ctx->client->dev;
+
+ /* write address only */
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_7_0, 0x30);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_COMMAND, 0x04);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_CTRL_STATUS,
+ AP_AUX_CTRL_ADDRONLY | AP_AUX_CTRL_OP_EN);
+
+ ret |= wait_aux_op_finish(ctx);
+ /* write segment address */
+ ret |= sp_tx_aux_wr(ctx, segment);
+ /* data read */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_7_0, 0x50);
+ if (ret) {
+ DRM_ERROR("IO error : aux initial failed.\n");
+ return ret;
+ }
+
+ for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) {
+ sp_tx_aux_wr(ctx, offset);
+ /* set I2C read com 0x01 mot = 0 and read 16 bytes */
+ ret = sp_tx_aux_rd(ctx, 0xf1);
+
+ if (ret) {
+ ret = sp_tx_rst_aux(ctx);
+ DRM_DEV_ERROR(dev, "segment read failed, reset!\n");
+ } else {
+ ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_BUFF_START,
+ MAX_DPCD_BUFFER_SIZE, buf);
+ if (ret > 0)
+ break;
+ }
+ }
+
+ if (cnt > EDID_TRY_CNT)
+ return -EIO;
+
+ return 0;
+}
+
+static int sp_tx_edid_read(struct anx7625_data *ctx,
+ u8 *pedid_blocks_buf)
+{
+ u8 offset, edid_pos;
+ int count, blocks_num;
+ u8 pblock_buf[MAX_DPCD_BUFFER_SIZE];
+ u8 i, j;
+ u8 g_edid_break = 0;
+ int ret;
+ struct device *dev = &ctx->client->dev;
+
+ /* address initial */
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_7_0, 0x50);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_15_8, 0);
+ ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+ AP_AUX_ADDR_19_16, 0xf0);
+ if (ret < 0) {
+ DRM_ERROR("access aux channel IO error.\n");
+ return -EIO;
+ }
+
+ blocks_num = sp_tx_get_edid_block(ctx);
+ if (blocks_num < 0)
+ return blocks_num;
+
+ count = 0;
+
+ do {
+ switch (count) {
+ case 0:
+ case 1:
+ for (i = 0; i < 8; i++) {
+ offset = (i + count * 8) * MAX_DPCD_BUFFER_SIZE;
+ g_edid_break = edid_read(ctx, offset,
+ pblock_buf);
+
+ if (g_edid_break)
+ break;
+
+ memcpy(&pedid_blocks_buf[offset],
+ pblock_buf,
+ MAX_DPCD_BUFFER_SIZE);
+ }
+
+ break;
+ case 2:
+ offset = 0x00;
+
+ for (j = 0; j < 8; j++) {
+ edid_pos = (j + count * 8) *
+ MAX_DPCD_BUFFER_SIZE;
+
+ if (g_edid_break == 1)
+ break;
+
+ segments_edid_read(ctx, count / 2,
+ pblock_buf, offset);
+ memcpy(&pedid_blocks_buf[edid_pos],
+ pblock_buf,
+ MAX_DPCD_BUFFER_SIZE);
+ offset = offset + 0x10;
+ }
+
+ break;
+ case 3:
+ offset = 0x80;
+
+ for (j = 0; j < 8; j++) {
+ edid_pos = (j + count * 8) *
+ MAX_DPCD_BUFFER_SIZE;
+ if (g_edid_break == 1)
+ break;
+
+ segments_edid_read(ctx, count / 2,
+ pblock_buf, offset);
+ memcpy(&pedid_blocks_buf[edid_pos],
+ pblock_buf,
+ MAX_DPCD_BUFFER_SIZE);
+ offset = offset + 0x10;
+ }
+
+ break;
+ default:
+ break;
+ }
+
+ count++;
+
+ } while (blocks_num >= count);
+
+ /* check edid data */
+ if (!drm_edid_is_valid((struct edid *)pedid_blocks_buf)) {
+ DRM_DEV_ERROR(dev, "WARNING! edid check failed!\n");
+ return -EINVAL;
+ }
+
+ /* reset aux channel */
+ sp_tx_rst_aux(ctx);
+
+ return (blocks_num + 1);
+}
+
+static void anx7625_power_on(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+
+ if (!ctx->pdata.low_power_mode) {
+ DRM_DEV_DEBUG_DRIVER(dev, "Anx7625 not low power mode!\n");
+ return;
+ }
+
+ /* power on pin enable */
+ gpiod_set_value(ctx->pdata.gpio_p_on, 1);
+ usleep_range(10000, 11000);
+ /* power reset pin enable */
+ gpiod_set_value(ctx->pdata.gpio_reset, 1);
+ usleep_range(10000, 11000);
+
+ DRM_DEV_DEBUG_DRIVER(dev, "Anx7625 power on !\n");
+}
+
+static void anx7625_power_standby(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+
+ if (!ctx->pdata.low_power_mode) {
+ DRM_DEV_DEBUG_DRIVER(dev, "anx7625 not low power mode!\n");
+ return;
+ }
+
+ gpiod_set_value(ctx->pdata.gpio_reset, 0);
+ usleep_range(1000, 1100);
+ gpiod_set_value(ctx->pdata.gpio_p_on, 0);
+ usleep_range(1000, 1100);
+ DRM_DEV_DEBUG_DRIVER(dev, "anx7625 power down\n");
+}
+
+/* basic configurations of ANX7625 */
+static void anx7625_config(struct anx7625_data *ctx)
+{
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ XTAL_FRQ_SEL, XTAL_FRQ_27M);
+}
+
+static void anx7625_disable_pd_protocol(struct anx7625_data *ctx)
+{
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ /* reset main ocm */
+ ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x40);
+ /* Disable PD */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ AP_AV_STATUS, AP_DISABLE_PD);
+ /* release main ocm */
+ ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x00);
+
+ if (ret < 0)
+ DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature failed.\n");
+ else
+ DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature succeeded.\n");
+}
+
+static void anx7625_power_on_init(struct anx7625_data *ctx)
+{
+ int retry_count, i;
+ int ret;
+ struct device *dev = &ctx->client->dev;
+
+ for (retry_count = 0; retry_count < 3; retry_count++) {
+ anx7625_power_on(ctx);
+ anx7625_config(ctx);
+
+ for (i = 0; i < OCM_LOADING_TIME; i++) {
+ /* check interface workable */
+ ret = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+ FLASH_LOAD_STA);
+ if (ret < 0) {
+ DRM_ERROR("IO error : access flash load.\n");
+ return;
+ }
+ if ((ret & FLASH_LOAD_STA_CHK) == FLASH_LOAD_STA_CHK) {
+ anx7625_disable_pd_protocol(ctx);
+ DRM_DEV_DEBUG_DRIVER(dev,
+ "Firmware ver %02x%02x,",
+ anx7625_reg_read(ctx,
+ ctx->i2c.rx_p0_client,
+ OCM_FW_VERSION),
+ anx7625_reg_read(ctx,
+ ctx->i2c.rx_p0_client,
+ OCM_FW_REVERSION));
+ DRM_DEV_DEBUG_DRIVER(dev, "Driver version %s\n",
+ ANX7625_DRV_VERSION);
+
+ return;
+ }
+ usleep_range(1000, 1100);
+ }
+ anx7625_power_standby(ctx);
+ }
+}
+
+static int anx7625_extcon_notifier(struct notifier_block *nb,
+ unsigned long event, void *ptr)
+{
+ struct anx7625_data *ctx =
+ container_of(nb, struct anx7625_data, event_nb);
+
+ schedule_work(&ctx->extcon_wq);
+ return NOTIFY_DONE;
+}
+
+static void anx7625_chip_control(struct anx7625_data *ctx, int state)
+{
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "before set, power_state(%d).\n",
+ atomic_read(&ctx->power_status));
+
+ if (!ctx->pdata.low_power_mode)
+ return;
+
+ if (state) {
+ atomic_inc(&ctx->power_status);
+ if (atomic_read(&ctx->power_status) == 1)
+ anx7625_power_on_init(ctx);
+ } else {
+ if (atomic_read(&ctx->power_status)) {
+ atomic_dec(&ctx->power_status);
+
+ if (atomic_read(&ctx->power_status) == 0)
+ anx7625_power_standby(ctx);
+ }
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, "after set, power_state(%d).\n",
+ atomic_read(&ctx->power_status));
+}
+
+static void anx7625_extcon_work(struct work_struct *work)
+{
+ struct anx7625_data *ctx =
+ container_of(work, struct anx7625_data, extcon_wq);
+ int state = extcon_get_state(ctx->extcon, EXTCON_DISP_DP);
+
+ mutex_lock(&ctx->lock);
+ anx7625_chip_control(ctx, state);
+ mutex_unlock(&ctx->lock);
+}
+
+static int anx7625_extcon_notifier_init(struct anx7625_data *ctx)
+{
+ int ret;
+ struct device *dev = &ctx->client->dev;
+
+ ctx->event_nb.notifier_call = anx7625_extcon_notifier;
+ INIT_WORK(&ctx->extcon_wq, anx7625_extcon_work);
+ ret = devm_extcon_register_notifier(&ctx->client->dev, ctx->extcon,
+ EXTCON_DISP_DP, &ctx->event_nb);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "failed to register notifier for DP");
+ return ret;
+ }
+ return 0;
+}
+
+static void anx7625_init_gpio(struct anx7625_data *platform)
+{
+ struct device *dev = &platform->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "anx7625 init gpio\n");
+
+ /* gpio for chip power enable */
+ platform->pdata.gpio_p_on =
+ devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW);
+ /* gpio for chip reset */
+ platform->pdata.gpio_reset =
+ devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+
+ if (platform->pdata.gpio_p_on && platform->pdata.gpio_reset) {
+ platform->pdata.low_power_mode = 1;
+ DRM_DEV_DEBUG_DRIVER(dev, "low power mode, pon %d, reset %d.\n",
+ desc_to_gpio(platform->pdata.gpio_p_on),
+ desc_to_gpio(platform->pdata.gpio_reset));
+ } else {
+ platform->pdata.low_power_mode = 0;
+ DRM_DEV_DEBUG_DRIVER(dev, "not low power mode.\n");
+ }
+}
+
+static void anx7625_stop_dp_work(struct anx7625_data *ctx)
+{
+ ctx->hpd_status = 0;
+ ctx->hpd_high_cnt = 0;
+ ctx->display_timing_valid = 0;
+
+ ctx->slimport_edid_p.edid_block_num = -1;
+
+ if (ctx->pdata.low_power_mode == 0)
+ anx7625_disable_pd_protocol(ctx);
+}
+
+static void anx7625_start_dp_work(struct anx7625_data *ctx)
+{
+ int ret;
+ struct device *dev = &ctx->client->dev;
+
+ if (ctx->hpd_high_cnt >= 2) {
+ DRM_DEV_DEBUG_DRIVER(dev, "anx7625 filter useless HPD\n");
+ return;
+ }
+
+ ctx->hpd_high_cnt++;
+
+ /* not support HDCP */
+ ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f);
+
+ /* try auth flag */
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
+ /* interrupt for DRM */
+ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
+ if (ret < 0)
+ return;
+
+ ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86);
+ if (ret < 0)
+ return;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "Secure OCM version=%02x\n", ret);
+}
+
+static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx)
+{
+ return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS);
+}
+
+static void anx7625_hpd_polling(struct anx7625_data *ctx)
+{
+ int ret, val;
+ struct device *dev = &ctx->client->dev;
+
+ if (atomic_read(&ctx->power_status) != 1) {
+ DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
+ return;
+ }
+
+ ret = readx_poll_timeout(anx7625_read_hpd_status_p0,
+ ctx, val,
+ ((val & HPD_STATUS) || (val < 0)),
+ 5000,
+ 5000 * 100);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "HPD polling timeout!\n");
+ } else {
+ DRM_DEV_DEBUG_DRIVER(dev, "HPD raise up.\n");
+ anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+ INTR_ALERT_1, 0xFF);
+ anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ INTERFACE_CHANGE_INT, 0);
+ }
+
+ anx7625_start_dp_work(ctx);
+}
+
+static void anx7625_disconnect_check(struct anx7625_data *ctx)
+{
+ if (atomic_read(&ctx->power_status) == 0)
+ anx7625_stop_dp_work(ctx);
+}
+
+static void anx7625_low_power_mode_check(struct anx7625_data *ctx,
+ int state)
+{
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "low power mode check, state(%d).\n", state);
+
+ if (ctx->pdata.low_power_mode) {
+ anx7625_chip_control(ctx, state);
+ if (state)
+ anx7625_hpd_polling(ctx);
+ else
+ anx7625_disconnect_check(ctx);
+ }
+}
+
+static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
+{
+ struct device *dev = &ctx->client->dev;
+
+ /* hpd changed */
+ DRM_DEV_DEBUG_DRIVER(dev, "dp_hpd_change_default_func: %d\n",
+ (u32)on);
+
+ if (on == 0) {
+ DRM_DEV_DEBUG_DRIVER(dev, " HPD low\n");
+ anx7625_stop_dp_work(ctx);
+ } else {
+ DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n");
+ anx7625_start_dp_work(ctx);
+ }
+
+ ctx->hpd_status = 1;
+}
+
+static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
+{
+ int intr_vector, status;
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "power_status=%d\n",
+ (u32)atomic_read(&ctx->power_status));
+
+ status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client,
+ INTR_ALERT_1, 0xFF);
+ if (status < 0) {
+ DRM_ERROR("IO error : clear alert register.\n");
+ return status;
+ }
+
+ intr_vector = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+ INTERFACE_CHANGE_INT);
+ if (intr_vector < 0) {
+ DRM_ERROR("IO error : access interrupt change register.\n");
+ return intr_vector;
+ }
+ DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x44=%x\n", intr_vector);
+ status = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+ INTERFACE_CHANGE_INT,
+ intr_vector & (~intr_vector));
+ if (status < 0) {
+ DRM_ERROR("IO error : clear interrupt change register.\n");
+ return status;
+ }
+
+ if (!(intr_vector & HPD_STATUS_CHANGE))
+ return -ENOENT;
+
+ status = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client,
+ SYSTEM_STSTUS);
+ if (status < 0) {
+ DRM_ERROR("IO error : clear interrupt status.\n");
+ return status;
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x45=%x\n", status);
+ dp_hpd_change_handler(ctx, status & HPD_STATUS);
+
+ return 0;
+}
+
+static void anx7625_work_func(struct work_struct *work)
+{
+ int event;
+ struct anx7625_data *ctx = container_of(work,
+ struct anx7625_data, work);
+
+ mutex_lock(&ctx->lock);
+ event = anx7625_hpd_change_detect(ctx);
+ mutex_unlock(&ctx->lock);
+
+ if (event < 0)
+ return;
+
+ if (ctx->bridge_attached)
+ drm_helper_hpd_irq_event(ctx->connector.dev);
+}
+
+static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
+{
+ struct anx7625_data *ctx = (struct anx7625_data *)data;
+
+ if (atomic_read(&ctx->power_status) != 1)
+ return IRQ_NONE;
+
+ queue_work(ctx->workqueue, &ctx->work);
+
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_OF
+static int anx7625_parse_dt(struct device *dev,
+ struct anx7625_platform_data *pdata)
+{
+ struct device_node *np = dev->of_node;
+ struct device_node *panel_node, *out_ep;
+
+ of_property_read_u32(dev->of_node, "panel_flags",
+ &pdata->panel_flags);
+ DRM_DEV_DEBUG_DRIVER(dev, "panel_flags : %d\n", pdata->panel_flags);
+
+ if (pdata->panel_flags == 1)
+ pdata->internal_panel = 1;
+ else if (pdata->panel_flags == 2)
+ pdata->extcon_supported = 1;
+ DRM_DEV_DEBUG_DRIVER(dev, "%s support extcon, %s internal panel\n",
+ pdata->extcon_supported ? "" : "not",
+ pdata->internal_panel ? "has" : "no");
+
+ pdata->node.mipi_dsi_host_node = of_graph_get_remote_node(np, 0, 0);
+ if (pdata->node.mipi_dsi_host_node) {
+ of_node_put(pdata->node.mipi_dsi_host_node);
+ pdata->dsi_supported = 1;
+ DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n");
+ } else {
+ pdata->node.mipi_dpi_host_node =
+ of_graph_get_remote_node(np, 1, 0);
+
+ if (pdata->node.mipi_dpi_host_node) {
+ of_node_put(pdata->node.mipi_dpi_host_node);
+ DRM_DEV_DEBUG_DRIVER(dev, "found dpi host node.\n");
+ }
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, "dsi_supported : %d\n", pdata->dsi_supported);
+
+ pdata->node.panel_node = of_graph_get_port_by_id(np, 2);
+ if (pdata->node.panel_node) {
+ of_node_put(pdata->node.panel_node);
+ out_ep = of_get_child_by_name(pdata->node.panel_node,
+ "endpoint");
+ if (!out_ep) {
+ DRM_DEV_DEBUG_DRIVER(dev, "cannot get endpoint.\n");
+ return -EPROBE_DEFER;
+ }
+
+ panel_node = of_graph_get_remote_port_parent(out_ep);
+ of_node_put(out_ep);
+
+ pdata->panel = of_drm_find_panel(panel_node);
+ DRM_DEV_DEBUG_DRIVER(dev, "get panel node.\n");
+ of_node_put(panel_node);
+ if (IS_ERR_OR_NULL(pdata->panel))
+ return -EPROBE_DEFER;
+ } else {
+ if (pdata->internal_panel) {
+ DRM_ERROR("failed to get internal panel.\n");
+ return -EPROBE_DEFER;
+ }
+ }
+
+ return 0;
+}
+#else
+static int anx7625_parse_dt(struct device *dev,
+ struct anx7625_platform_data *pdata)
+{
+ return -ENODEV;
+}
+#endif
+
+static inline struct anx7625_data *connector_to_anx7625(struct drm_connector *c)
+{
+ return container_of(c, struct anx7625_data, connector);
+}
+
+static inline struct anx7625_data *bridge_to_anx7625(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct anx7625_data, bridge);
+}
+
+static void anx7625_post_disable(struct drm_bridge *bridge)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "post disable\n");
+
+ if (!ctx->pdata.panel)
+ return;
+
+ ret = drm_panel_unprepare(ctx->pdata.panel);
+ if (ret)
+ DRM_ERROR("failed to unprepare panel: %d\n", ret);
+ else
+ DRM_DEV_DEBUG_DRIVER(dev, "backlight unprepared.\n");
+
+ atomic_set(&ctx->panel_power, 0);
+}
+
+static void anx7625_pre_enable(struct drm_bridge *bridge)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "pre enable\n");
+
+ if (!ctx->pdata.panel)
+ return;
+
+ ret = drm_panel_prepare(ctx->pdata.panel);
+ if (ret < 0)
+ DRM_ERROR("failed to prepare panel: %d\n", ret);
+ else
+ DRM_DEV_DEBUG_DRIVER(dev, "backlight prepared.\n");
+ atomic_set(&ctx->panel_power, 1);
+}
+
+static int anx7625_get_modes(struct drm_connector *connector)
+{
+ struct anx7625_data *ctx = connector_to_anx7625(connector);
+ int err, num_modes = 0;
+ int turn_off_flag = 0;
+ struct s_edid_data *p_edid = &ctx->slimport_edid_p;
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm get modes\n");
+
+ if (ctx->slimport_edid_p.edid_block_num > 0)
+ goto out;
+
+ mutex_lock(&ctx->lock);
+
+ if (ctx->pdata.panel && atomic_read(&ctx->panel_power) == 0) {
+ turn_off_flag = 1;
+ anx7625_pre_enable(&ctx->bridge);
+ }
+
+ anx7625_low_power_mode_check(ctx, 1);
+
+ p_edid->edid_block_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data);
+
+ err = -EIO;
+ if (p_edid->edid_block_num < 0) {
+ DRM_ERROR("Failed to read EDID.\n");
+ goto fail;
+ }
+
+ err = drm_connector_update_edid_property(connector,
+ (struct edid *)
+ &p_edid->edid_raw_data);
+
+ if (err)
+ DRM_ERROR("Failed to update EDID property: %d\n", err);
+
+fail:
+ mutex_unlock(&ctx->lock);
+ anx7625_low_power_mode_check(ctx, 0);
+ if (ctx->pdata.panel && turn_off_flag == 1)
+ anx7625_post_disable(&ctx->bridge);
+
+ if (err)
+ return err;
+
+out:
+ num_modes = drm_add_edid_modes(connector,
+ (struct edid *)&p_edid->edid_raw_data);
+ DRM_DEV_DEBUG_DRIVER(dev, "num_modes(%d)\n", num_modes);
+
+ return num_modes;
+}
+
+static enum drm_mode_status
+anx7625_connector_mode_valid(struct drm_connector *connector,
+ struct drm_display_mode *mode)
+{
+ struct anx7625_data *ctx = connector_to_anx7625(connector);
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm modes valid verify\n");
+
+ if (mode->clock > SUPPORT_PIXEL_CLOCK)
+ return MODE_CLOCK_HIGH;
+
+ return MODE_OK;
+}
+
+static struct drm_connector_helper_funcs anx7625_connector_helper_funcs = {
+ .get_modes = anx7625_get_modes,
+ .mode_valid = anx7625_connector_mode_valid,
+};
+
+static enum drm_connector_status anx7625_detect(struct drm_connector *connector,
+ bool force)
+{
+ struct anx7625_data *ctx = connector_to_anx7625(connector);
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm detect\n");
+
+ if (ctx->pdata.internal_panel)
+ return connector_status_connected;
+
+ if (!ctx->hpd_status)
+ return connector_status_disconnected;
+
+ return connector_status_connected;
+}
+
+static const struct drm_connector_funcs anx7625_connector_funcs = {
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = anx7625_detect,
+ .destroy = drm_connector_cleanup,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static int anx7625_attach_dsi(struct anx7625_data *ctx)
+{
+ struct mipi_dsi_host *host;
+ struct mipi_dsi_device *dsi;
+ struct device_node *mipi_host_node;
+ struct device *dev = &ctx->client->dev;
+ const struct mipi_dsi_device_info info = {
+ .type = "anx7625",
+ .channel = 0,
+ .node = NULL,
+ };
+
+ DRM_DEV_DEBUG_DRIVER(dev, "attach dsi\n");
+
+ if (ctx->pdata.dsi_supported)
+ mipi_host_node = ctx->pdata.node.mipi_dsi_host_node;
+ else
+ mipi_host_node = ctx->pdata.node.mipi_dpi_host_node;
+
+ if (!mipi_host_node) {
+ DRM_ERROR("dsi host is not configured.\n");
+ return -EINVAL;
+ }
+
+ host = of_find_mipi_dsi_host_by_node(mipi_host_node);
+ if (!host) {
+ DRM_ERROR("failed to find dsi host.\n");
+ return -EINVAL;
+ }
+
+ dsi = mipi_dsi_device_register_full(host, &info);
+ if (IS_ERR(dsi)) {
+ DRM_ERROR("failed to create dsi device.\n");
+ return -EINVAL;
+ }
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
+ MIPI_DSI_MODE_EOT_PACKET |
+ MIPI_DSI_MODE_VIDEO_HSE;
+
+ if (mipi_dsi_attach(dsi) < 0) {
+ DRM_ERROR("failed to attach dsi to host.\n");
+ mipi_dsi_device_unregister(dsi);
+ return -EINVAL;
+ }
+
+ ctx->dsi = dsi;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "attach dsi succeeded.\n");
+
+ return 0;
+}
+
+static void anx7625_bridge_detach(struct drm_bridge *bridge)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+
+ if (ctx->dsi) {
+ mipi_dsi_detach(ctx->dsi);
+ mipi_dsi_device_unregister(ctx->dsi);
+ }
+
+ if (ctx->bridge_attached)
+ drm_connector_unregister(&ctx->connector);
+}
+
+static int anx7625_bridge_attach(struct drm_bridge *bridge)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+ int err;
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm attach\n");
+ if (!bridge->encoder) {
+ DRM_ERROR("Parent encoder object not found");
+ return -ENODEV;
+ }
+
+ err = drm_connector_init(bridge->dev, &ctx->connector,
+ &anx7625_connector_funcs,
+ DRM_MODE_CONNECTOR_DisplayPort);
+ if (err) {
+ DRM_ERROR("Failed to initialize connector: %d\n", err);
+ return err;
+ }
+
+ drm_connector_helper_add(&ctx->connector,
+ &anx7625_connector_helper_funcs);
+
+ err = drm_connector_register(&ctx->connector);
+ if (err) {
+ DRM_ERROR("Failed to register connector: %d\n", err);
+ return err;
+ }
+
+ ctx->connector.polled = DRM_CONNECTOR_POLL_HPD;
+
+ err = drm_connector_attach_encoder(&ctx->connector, bridge->encoder);
+ if (err) {
+ DRM_ERROR("Failed to link up connector to encoder: %d\n", err);
+ drm_connector_unregister(&ctx->connector);
+ return err;
+ }
+
+ err = anx7625_attach_dsi(ctx);
+ if (err) {
+ DRM_ERROR("Failed to attach to dsi : %d\n", err);
+ drm_connector_unregister(&ctx->connector);
+ return err;
+ }
+
+ ctx->bridge_attached = 1;
+
+ return 0;
+}
+
+static enum drm_mode_status
+anx7625_bridge_mode_valid(struct drm_bridge *bridge,
+ const struct drm_display_mode *mode)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm mode checking\n");
+
+ /* Max 1200p at 5.4 Ghz, one lane, pixel clock 300M */
+ if (mode->clock > SUPPORT_PIXEL_CLOCK) {
+ DRM_DEV_DEBUG_DRIVER(dev,
+ "drm mode invalid, pixelclock too high.\n");
+ return MODE_CLOCK_HIGH;
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm mode valid.\n");
+
+ return MODE_OK;
+}
+
+static void anx7625_bridge_mode_set(struct drm_bridge *bridge,
+ const struct drm_display_mode *old_mode,
+ const struct drm_display_mode *mode)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+ struct device *dev = &ctx->client->dev;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm mode set\n");
+
+ mutex_lock(&ctx->lock);
+
+ ctx->dt.pixelclock.min = mode->clock;
+ ctx->dt.hactive.min = mode->hdisplay;
+ ctx->dt.hsync_len.min = mode->hsync_end - mode->hsync_start;
+ ctx->dt.hfront_porch.min = mode->hsync_start - mode->hdisplay;
+ ctx->dt.hback_porch.min = mode->htotal - mode->hsync_end;
+ ctx->dt.vactive.min = mode->vdisplay;
+ ctx->dt.vsync_len.min = mode->vsync_end - mode->vsync_start;
+ ctx->dt.vfront_porch.min = mode->vsync_start - mode->vdisplay;
+ ctx->dt.vback_porch.min = mode->vtotal - mode->vsync_end;
+
+ ctx->display_timing_valid = 1;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "pixelclock(%d).\n", ctx->dt.pixelclock.min);
+ DRM_DEV_DEBUG_DRIVER(dev, "hactive(%d), hsync(%d), hfp(%d), hbp(%d)\n",
+ ctx->dt.hactive.min,
+ ctx->dt.hsync_len.min,
+ ctx->dt.hfront_porch.min,
+ ctx->dt.hback_porch.min);
+ DRM_DEV_DEBUG_DRIVER(dev, "vactive(%d), vsync(%d), vfp(%d), vbp(%d)\n",
+ ctx->dt.vactive.min,
+ ctx->dt.vsync_len.min,
+ ctx->dt.vfront_porch.min,
+ ctx->dt.vback_porch.min);
+ DRM_DEV_DEBUG_DRIVER(dev, "hdisplay(%d),hsync_start(%d).\n",
+ mode->hdisplay,
+ mode->hsync_start);
+ DRM_DEV_DEBUG_DRIVER(dev, "hsync_end(%d),htotal(%d).\n",
+ mode->hsync_end,
+ mode->htotal);
+ DRM_DEV_DEBUG_DRIVER(dev, "vdisplay(%d),vsync_start(%d).\n",
+ mode->vdisplay,
+ mode->vsync_start);
+ DRM_DEV_DEBUG_DRIVER(dev, "vsync_end(%d),vtotal(%d).\n",
+ mode->vsync_end,
+ mode->vtotal);
+
+ mutex_unlock(&ctx->lock);
+}
+
+static void anx7625_bridge_enable(struct drm_bridge *bridge)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm enable\n");
+
+ anx7625_low_power_mode_check(ctx, 1);
+
+ if (WARN_ON(!atomic_read(&ctx->power_status)))
+ return;
+
+ if (ctx->pdata.panel) {
+ ret = drm_panel_enable(ctx->pdata.panel);
+ if (ret < 0) {
+ DRM_ERROR("failed to enable panel: %d.\n", ret);
+ return;
+ }
+ }
+
+ mutex_lock(&ctx->lock);
+ anx7625_dp_start(ctx);
+ mutex_unlock(&ctx->lock);
+}
+
+static void anx7625_bridge_disable(struct drm_bridge *bridge)
+{
+ struct anx7625_data *ctx = bridge_to_anx7625(bridge);
+ struct device *dev = &ctx->client->dev;
+ int ret;
+
+ if (WARN_ON(!atomic_read(&ctx->power_status)))
+ return;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
+
+ if (ctx->pdata.panel) {
+ ret = drm_panel_disable(ctx->pdata.panel);
+ if (ret < 0)
+ DRM_ERROR("failed to disable panel: %d.\n", ret);
+ }
+
+ DRM_DEV_DEBUG_DRIVER(dev, "drm disable\n");
+ mutex_lock(&ctx->lock);
+
+ anx7625_dp_stop(ctx);
+
+ anx7625_low_power_mode_check(ctx, 0);
+
+ mutex_unlock(&ctx->lock);
+}
+
+static const struct drm_bridge_funcs anx7625_bridge_funcs = {
+ .attach = anx7625_bridge_attach,
+ .detach = anx7625_bridge_detach,
+ .disable = anx7625_bridge_disable,
+ .post_disable = anx7625_post_disable,
+ .pre_enable = anx7625_pre_enable,
+ .mode_valid = anx7625_bridge_mode_valid,
+ .mode_set = anx7625_bridge_mode_set,
+ .enable = anx7625_bridge_enable,
+};
+
+static int anx7625_register_i2c_dummy_clients(struct anx7625_data *ctx,
+ struct i2c_client *client)
+{
+ ctx->i2c.tx_p0_client = i2c_new_dummy(client->adapter,
+ TX_P0_ADDR >> 1);
+ if (!ctx->i2c.tx_p0_client)
+ return -ENOMEM;
+
+ ctx->i2c.tx_p1_client = i2c_new_dummy(client->adapter,
+ TX_P1_ADDR >> 1);
+ if (!ctx->i2c.tx_p1_client)
+ goto free_tx_p0;
+
+ ctx->i2c.tx_p2_client = i2c_new_dummy(client->adapter,
+ TX_P2_ADDR >> 1);
+ if (!ctx->i2c.tx_p2_client)
+ goto free_tx_p1;
+
+ ctx->i2c.rx_p0_client = i2c_new_dummy(client->adapter,
+ RX_P0_ADDR >> 1);
+ if (!ctx->i2c.rx_p0_client)
+ goto free_tx_p2;
+
+ ctx->i2c.rx_p1_client = i2c_new_dummy(client->adapter,
+ RX_P1_ADDR >> 1);
+ if (!ctx->i2c.rx_p1_client)
+ goto free_rx_p0;
+
+ ctx->i2c.rx_p2_client = i2c_new_dummy(client->adapter,
+ RX_P2_ADDR >> 1);
+ if (!ctx->i2c.rx_p2_client)
+ goto free_rx_p1;
+
+ ctx->i2c.tcpc_client = i2c_new_dummy(client->adapter,
+ TCPC_INTERFACE_ADDR >> 1);
+ if (!ctx->i2c.tcpc_client)
+ goto free_rx_p2;
+
+ return 0;
+
+free_rx_p2:
+ i2c_unregister_device(ctx->i2c.rx_p2_client);
+free_rx_p1:
+ i2c_unregister_device(ctx->i2c.rx_p1_client);
+free_rx_p0:
+ i2c_unregister_device(ctx->i2c.rx_p0_client);
+free_tx_p2:
+ i2c_unregister_device(ctx->i2c.tx_p2_client);
+free_tx_p1:
+ i2c_unregister_device(ctx->i2c.tx_p1_client);
+free_tx_p0:
+ i2c_unregister_device(ctx->i2c.tx_p0_client);
+
+ return -ENOMEM;
+}
+
+static void anx7625_unregister_i2c_dummy_clients(struct anx7625_data *ctx)
+{
+ i2c_unregister_device(ctx->i2c.tx_p0_client);
+ i2c_unregister_device(ctx->i2c.tx_p1_client);
+ i2c_unregister_device(ctx->i2c.tx_p2_client);
+ i2c_unregister_device(ctx->i2c.rx_p0_client);
+ i2c_unregister_device(ctx->i2c.rx_p1_client);
+ i2c_unregister_device(ctx->i2c.rx_p2_client);
+ i2c_unregister_device(ctx->i2c.tcpc_client);
+}
+
+static int anx7625_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct anx7625_data *platform;
+ struct anx7625_platform_data *pdata;
+ int ret = 0;
+ struct device *dev = &client->dev;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_I2C_BLOCK)) {
+ DRM_DEV_ERROR(dev, "anx7625's i2c bus doesn't support\n");
+ return -ENODEV;
+ }
+
+ platform = kzalloc(sizeof(*platform), GFP_KERNEL);
+ if (!platform) {
+ DRM_DEV_ERROR(dev, "failed to allocate driver data\n");
+ return -ENOMEM;
+ }
+
+ pdata = &platform->pdata;
+
+ ret = anx7625_parse_dt(dev, pdata);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "failed to parse devicetree.\n");
+ goto free_platform;
+ }
+
+ platform->client = client;
+ i2c_set_clientdata(client, platform);
+
+ anx7625_init_gpio(platform);
+
+ if (platform->pdata.extcon_supported) {
+ /* get extcon device from DTS */
+ ret = -EINVAL;
+ platform->extcon = extcon_get_edev_by_phandle(dev, 0);
+ if (PTR_ERR(platform->extcon) == -EPROBE_DEFER)
+ goto free_platform;
+
+ if (IS_ERR(platform->extcon)) {
+ DRM_DEV_ERROR(dev,
+ "can not get extcon device!");
+ goto free_platform;
+ }
+
+ ret = anx7625_extcon_notifier_init(platform);
+ if (ret)
+ goto free_platform;
+ }
+
+ atomic_set(&platform->power_status, 0);
+
+ mutex_init(&platform->lock);
+
+ platform->pdata.intp_irq = client->irq;
+ if (platform->pdata.intp_irq) {
+ INIT_WORK(&platform->work, anx7625_work_func);
+ platform->workqueue = create_workqueue("anx7625_work");
+ if (!platform->workqueue) {
+ DRM_DEV_ERROR(dev, "failed to create work queue\n");
+ ret = -ENOMEM;
+ goto free_platform;
+ }
+
+ ret = devm_request_threaded_irq(dev, platform->pdata.intp_irq,
+ NULL, anx7625_intr_hpd_isr,
+ IRQF_TRIGGER_FALLING |
+ IRQF_ONESHOT,
+ "anx7625-intp", platform);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "failed to request irq\n");
+ goto free_wq;
+ }
+ }
+
+ if (anx7625_register_i2c_dummy_clients(platform, client) != 0) {
+ ret = -ENOMEM;
+ DRM_ERROR("Failed to reserve I2C bus.\n");
+ goto free_wq;
+ }
+
+ if (platform->pdata.low_power_mode == 0) {
+ anx7625_disable_pd_protocol(platform);
+ atomic_set(&platform->power_status, 1);
+ }
+
+ /* add work function */
+ if (platform->pdata.intp_irq)
+ queue_work(platform->workqueue, &platform->work);
+
+ platform->bridge.funcs = &anx7625_bridge_funcs;
+ if (IS_ENABLED(CONFIG_OF))
+ platform->bridge.of_node = client->dev.of_node;
+ drm_bridge_add(&platform->bridge);
+
+ DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");
+
+ return 0;
+
+free_wq:
+ if (platform->workqueue)
+ destroy_workqueue(platform->workqueue);
+
+free_platform:
+ kfree(platform);
+
+ return ret;
+}
+
+static int anx7625_i2c_remove(struct i2c_client *client)
+{
+ struct anx7625_data *platform = i2c_get_clientdata(client);
+
+ drm_bridge_remove(&platform->bridge);
+
+ if (platform->pdata.intp_irq)
+ destroy_workqueue(platform->workqueue);
+
+ if (platform->pdata.extcon_supported) {
+ devm_extcon_unregister_notifier(&platform->client->dev,
+ platform->extcon,
+ EXTCON_DISP_DP,
+ &platform->event_nb);
+ flush_work(&platform->extcon_wq);
+ }
+
+ anx7625_unregister_i2c_dummy_clients(platform);
+
+ kfree(platform);
+ return 0;
+}
+
+static const struct i2c_device_id anx7625_id[] = {
+ {"anx7625", 0},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, anx7625_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id anx_match_table[] = {
+ {.compatible = "analogix,anx7625",},
+ {},
+};
+#endif
+
+static struct i2c_driver anx7625_driver = {
+ .driver = {
+ .name = "anx7625",
+#ifdef CONFIG_OF
+ .of_match_table = anx_match_table,
+#endif
+ },
+ .probe = anx7625_i2c_probe,
+ .remove = anx7625_i2c_remove,
+
+ .id_table = anx7625_id,
+};
+
+module_i2c_driver(anx7625_driver);
+
+MODULE_DESCRIPTION("MIPI2DP anx7625 driver");
+MODULE_AUTHOR("Xin Ji <xji@analogixsemi.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_VERSION(ANX7625_DRV_VERSION);
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
new file mode 100644
index 0000000..c871a6c
--- /dev/null
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -0,0 +1,406 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright(c) 2016, Analogix Semiconductor. All rights reserved.
+ *
+ */
+
+#ifndef __ANX7625_H__
+#define __ANX7625_H__
+
+#ifndef LOG_TAG
+#define LOG_TAG "anx7625dp"
+#endif
+
+#define ANX7625_DRV_VERSION "0.1.04"
+
+/* Loading OCM re-trying times */
+#define OCM_LOADING_TIME 10
+
+/********* ANX7625 Register **********/
+#define TX_P0_ADDR 0x70
+#define TX_P1_ADDR 0x7A
+#define TX_P2_ADDR 0x72
+
+#define RX_P0_ADDR 0x7e
+#define RX_P1_ADDR 0x84
+#define RX_P2_ADDR 0x54
+
+#define RSVD_00_ADDR 0x00
+#define RSVD_D1_ADDR 0xD1
+#define RSVD_60_ADDR 0x60
+#define RSVD_39_ADDR 0x39
+#define RSVD_7F_ADDR 0x7F
+
+#define TCPC_INTERFACE_ADDR 0x58
+
+/* anx7625 clock frequency in Hz */
+#define XTAL_FRQ (27 * 1000000)
+
+#define POST_DIVIDER_MIN 1
+#define POST_DIVIDER_MAX 16
+#define PLL_OUT_FREQ_MIN 520000000UL
+#define PLL_OUT_FREQ_MAX 730000000UL
+#define PLL_OUT_FREQ_ABS_MIN 300000000UL
+#define PLL_OUT_FREQ_ABS_MAX 800000000UL
+#define MAX_UNSIGNED_24BIT 16777215UL
+
+/***************************************************************/
+/* Register definition of device address 0x58 */
+
+#define PRODUCT_ID_L 0x02
+#define PRODUCT_ID_H 0x03
+
+#define INTR_ALERT_1 0xCC
+#define INTR_SOFTWARE_INT BIT(3)
+#define INTR_RECEIVED_MSG BIT(5)
+
+#define SYSTEM_STSTUS 0x45
+#define INTERFACE_CHANGE_INT 0x44
+#define HPD_STATUS_CHANGE 0x80
+#define HPD_STATUS 0x80
+
+/******** END of I2C Address 0x58 ********/
+
+/***************************************************************/
+/* Register definition of device address 0x70 */
+#define I2C_ADDR_70_DPTX 0x70
+
+#define SP_TX_LINK_BW_SET_REG 0xA0
+#define SP_TX_LANE_COUNT_SET_REG 0xA1
+
+#define M_VID_0 0xC0
+#define M_VID_1 0xC1
+#define M_VID_2 0xC2
+#define N_VID_0 0xC3
+#define N_VID_1 0xC4
+#define N_VID_2 0xC5
+
+/***************************************************************/
+/* Register definition of device address 0x72 */
+#define AUX_RST 0x04
+#define RST_CTRL2 0x07
+
+#define SP_TX_TOTAL_LINE_STA_L 0x24
+#define SP_TX_TOTAL_LINE_STA_H 0x25
+#define SP_TX_ACT_LINE_STA_L 0x26
+#define SP_TX_ACT_LINE_STA_H 0x27
+#define SP_TX_V_F_PORCH_STA 0x28
+#define SP_TX_V_SYNC_STA 0x29
+#define SP_TX_V_B_PORCH_STA 0x2A
+#define SP_TX_TOTAL_PIXEL_STA_L 0x2B
+#define SP_TX_TOTAL_PIXEL_STA_H 0x2C
+#define SP_TX_ACT_PIXEL_STA_L 0x2D
+#define SP_TX_ACT_PIXEL_STA_H 0x2E
+#define SP_TX_H_F_PORCH_STA_L 0x2F
+#define SP_TX_H_F_PORCH_STA_H 0x30
+#define SP_TX_H_SYNC_STA_L 0x31
+#define SP_TX_H_SYNC_STA_H 0x32
+#define SP_TX_H_B_PORCH_STA_L 0x33
+#define SP_TX_H_B_PORCH_STA_H 0x34
+
+#define SP_TX_VID_CTRL 0x84
+#define SP_TX_BPC_MASK 0xE0
+#define SP_TX_BPC_6 0x00
+#define SP_TX_BPC_8 0x20
+#define SP_TX_BPC_10 0x40
+#define SP_TX_BPC_12 0x60
+
+#define VIDEO_BIT_MATRIX_12 0x4c
+
+#define AUDIO_CHANNEL_STATUS_1 0xd0
+#define AUDIO_CHANNEL_STATUS_2 0xd1
+#define AUDIO_CHANNEL_STATUS_3 0xd2
+#define AUDIO_CHANNEL_STATUS_4 0xd3
+#define AUDIO_CHANNEL_STATUS_5 0xd4
+#define AUDIO_CHANNEL_STATUS_6 0xd5
+#define TDM_SLAVE_MODE 0x10
+#define I2S_SLAVE_MODE 0x08
+
+#define AUDIO_CONTROL_REGISTER 0xe6
+#define TDM_TIMING_MODE 0x08
+
+#define I2C_ADDR_72_DPTX 0x72
+
+#define VIDEO_CONTROL_0 0x08
+
+#define ACTIVE_LINES_L 0x14
+#define ACTIVE_LINES_H 0x15 /* note: bit[7:6] are reserved */
+#define VERTICAL_FRONT_PORCH 0x16
+#define VERTICAL_SYNC_WIDTH 0x17
+#define VERTICAL_BACK_PORCH 0x18
+
+#define HORIZONTAL_TOTAL_PIXELS_L 0x19
+#define HORIZONTAL_TOTAL_PIXELS_H 0x1A /* note: bit[7:6] are reserved */
+#define HORIZONTAL_ACTIVE_PIXELS_L 0x1B
+#define HORIZONTAL_ACTIVE_PIXELS_H 0x1C /* note: bit[7:6] are reserved */
+#define HORIZONTAL_FRONT_PORCH_L 0x1D
+#define HORIZONTAL_FRONT_PORCH_H 0x1E /* note: bit[7:4] are reserved */
+#define HORIZONTAL_SYNC_WIDTH_L 0x1F
+#define HORIZONTAL_SYNC_WIDTH_H 0x20 /* note: bit[7:4] are reserved */
+#define HORIZONTAL_BACK_PORCH_L 0x21
+#define HORIZONTAL_BACK_PORCH_H 0x22 /* note: bit[7:4] are reserved */
+
+/******** END of I2C Address 0x72 *********/
+/***************************************************************/
+/* Register definition of device address 0x7e */
+
+#define I2C_ADDR_7E_FLASH_CONTROLLER 0x7E
+
+#define FLASH_LOAD_STA 0x05
+#define FLASH_LOAD_STA_CHK BIT(7)
+
+#define XTAL_FRQ_SEL 0x3F
+/* bit field positions */
+#define XTAL_FRQ_SEL_POS 5
+/* bit field values */
+#define XTAL_FRQ_19M2 (0 << XTAL_FRQ_SEL_POS)
+#define XTAL_FRQ_27M (4 << XTAL_FRQ_SEL_POS)
+
+#define R_DSC_CTRL_0 0x40
+#define READ_STATUS_EN 7
+#define CLK_1MEG_RB 6 /* 1MHz clock reset; 0=reset, 0=reset release */
+#define DSC_BIST_DONE 1 /* bit[5:1]: 1=DSC MBIST pass */
+#define DSC_EN 0x01 /* 1=DSC enabled, 0=DSC disabled */
+
+#define OCM_FW_VERSION 0x31
+#define OCM_FW_REVERSION 0x32
+
+#define AP_AUX_ADDR_7_0 0x11
+#define AP_AUX_ADDR_15_8 0x12
+#define AP_AUX_ADDR_19_16 0x13
+
+/* note: bit[0:3] AUX status, bit 4 op_en, bit 5 address only */
+#define AP_AUX_CTRL_STATUS 0x14
+#define AP_AUX_CTRL_OP_EN 0x10
+#define AP_AUX_CTRL_ADDRONLY 0x20
+
+#define AP_AUX_BUFF_START 0x15
+#define PIXEL_CLOCK_L 0x25
+#define PIXEL_CLOCK_H 0x26
+
+#define AP_AUX_COMMAND 0x27 /* com+len */
+/* bit 0&1: 3D video structure */
+/* 0x01: frame packing, 0x02:Line alternative, 0x03:Side-by-side(full) */
+#define AP_AV_STATUS 0x28
+#define AP_VIDEO_CHG BIT(2)
+#define AP_AUDIO_CHG BIT(3)
+#define AP_MIPI_MUTE BIT(4) /* 1:MIPI input mute, 0: ummute */
+#define AP_MIPI_RX_EN BIT(5) /* 1: MIPI RX input in 0: no RX in */
+#define AP_DISABLE_PD BIT(6)
+#define AP_DISABLE_DISPLAY BIT(7)
+/***************************************************************/
+/* Register definition of device address 0x84 */
+#define MIPI_PHY_CONTROL_3 0x03
+#define MIPI_HS_PWD_CLK 7
+#define MIPI_HS_RT_CLK 6
+#define MIPI_PD_CLK 5
+#define MIPI_CLK_RT_MANUAL_PD_EN 4
+#define MIPI_CLK_HS_MANUAL_PD_EN 3
+#define MIPI_CLK_DET_DET_BYPASS 2
+#define MIPI_CLK_MISS_CTRL 1
+#define MIPI_PD_LPTX_CH_MANUAL_PD_EN 0
+
+#define MIPI_LANE_CTRL_0 0x05
+#define MIPI_TIME_HS_PRPR 0x08
+
+/* After MIPI RX protocol layer received this many video frames, */
+/* protocol layer starts to reconstruct video stream from PHY */
+#define MIPI_VIDEO_STABLE_CNT 0x0A
+
+#define MIPI_LANE_CTRL_10 0x0F
+#define MIPI_DIGITAL_ADJ_1 0x1B
+
+#define MIPI_PLL_M_NUM_23_16 0x1E
+#define MIPI_PLL_M_NUM_15_8 0x1F
+#define MIPI_PLL_M_NUM_7_0 0x20
+#define MIPI_PLL_N_NUM_23_16 0x21
+#define MIPI_PLL_N_NUM_15_8 0x22
+#define MIPI_PLL_N_NUM_7_0 0x23
+
+#define MIPI_DIGITAL_PLL_6 0x2A
+/* bit[7:6]: VCO band control, only effective */
+/* when MIPI_PLL_FORCE_BAND_EN (0x84:0x2B[6]) is 1 */
+#define MIPI_M_NUM_READY 0x10
+#define MIPI_N_NUM_READY 0x08
+#define STABLE_INTEGER_CNT_EN 0x04
+#define MIPI_PLL_TEST_BIT 0
+/* bit[1:0]: test point output select - */
+/* 00: VCO power, 01: dvdd_pdt, 10: dvdd, 11: vcox */
+
+#define MIPI_DIGITAL_PLL_7 0x2B
+#define MIPI_PLL_FORCE_N_EN 7
+#define MIPI_PLL_FORCE_BAND_EN 6
+
+#define MIPI_PLL_VCO_TUNE_REG 4
+/* bit[5:4]: VCO metal capacitance - */
+/* 00: +20% fast, 01: +10% fast (default), 10: typical, 11: -10% slow */
+#define MIPI_PLL_VCO_TUNE_REG_VAL 0x30
+
+#define MIPI_PLL_PLL_LDO_BIT 2
+/* bit[3:2]: vco_v2i power - */
+/* 00: 1.40V, 01: 1.45V (default), 10: 1.50V, 11: 1.55V */
+#define MIPI_PLL_RESET_N 0x02
+#define MIPI_FRQ_FORCE_NDET 0
+
+#define MIPI_ALERT_CLR_0 0x2D
+#define HS_link_error_clear 7
+/* This bit itself is S/C, and it clears 0x84:0x31[7] */
+
+#define MIPI_ALERT_OUT_0 0x31
+#define check_sum_err_hs_sync 7
+/* This bit is cleared by 0x84:0x2D[7] */
+
+#define MIPI_DIGITAL_PLL_8 0x33
+#define MIPI_POST_DIV_VAL 4
+/* n means divided by (n+1), n = 0~15 */
+#define MIPI_EN_LOCK_FRZ 3
+#define MIPI_FRQ_COUNTER_RST 2
+#define MIPI_FRQ_SET_REG_8 1
+/* bit 0 is reserved */
+
+#define MIPI_DIGITAL_PLL_9 0x34
+
+#define MIPI_DIGITAL_PLL_16 0x3B
+#define MIPI_FRQ_FREEZE_NDET 7
+#define MIPI_FRQ_REG_SET_ENABLE 6
+#define MIPI_REG_FORCE_SEL_EN 5
+#define MIPI_REG_SEL_DIV_REG 4
+#define MIPI_REG_FORCE_PRE_DIV_EN 3
+/* bit 2 is reserved */
+#define MIPI_FREF_D_IND 1
+#define REF_CLK_27000KHZ 1
+#define REF_CLK_19200KHZ 0
+#define MIPI_REG_PLL_PLL_TEST_ENABLE 0
+
+#define MIPI_DIGITAL_PLL_18 0x3D
+#define FRQ_COUNT_RB_SEL 7
+#define REG_FORCE_POST_DIV_EN 6
+#define MIPI_DPI_SELECT 5
+#define SELECT_DSI 1
+#define SELECT_DPI 0
+#define REG_BAUD_DIV_RATIO 0
+
+#define H_BLANK_L 0x3E
+/* for DSC only */
+#define H_BLANK_H 0x3F
+/* for DSC only; note: bit[7:6] are reserved */
+#define MIPI_SWAP 0x4A
+#define MIPI_SWAP_CH0 7
+#define MIPI_SWAP_CH1 6
+#define MIPI_SWAP_CH2 5
+#define MIPI_SWAP_CH3 4
+#define MIPI_SWAP_CLK 3
+/* bit[2:0] are reserved */
+
+/******** END of I2C Address 0x84 *********/
+
+/* DPCD regs */
+#define DPCD_DPCD_REV 0x00
+#define DPCD_MAX_LINK_RATE 0x01
+#define DPCD_MAX_LANE_COUNT 0x02
+
+/********* ANX7625 Register End **********/
+
+/***************** Display *****************/
+enum audio_fs {
+ AUDIO_FS_441K = 0x00,
+ AUDIO_FS_48K = 0x02,
+ AUDIO_FS_32K = 0x03,
+ AUDIO_FS_882K = 0x08,
+ AUDIO_FS_96K = 0x0a,
+ AUDIO_FS_1764K = 0x0c,
+ AUDIO_FS_192K = 0x0e
+};
+
+enum audio_wd_len {
+ AUDIO_W_LEN_16_20MAX = 0x02,
+ AUDIO_W_LEN_18_20MAX = 0x04,
+ AUDIO_W_LEN_17_20MAX = 0x0c,
+ AUDIO_W_LEN_19_20MAX = 0x08,
+ AUDIO_W_LEN_20_20MAX = 0x0a,
+ AUDIO_W_LEN_20_24MAX = 0x03,
+ AUDIO_W_LEN_22_24MAX = 0x05,
+ AUDIO_W_LEN_21_24MAX = 0x0d,
+ AUDIO_W_LEN_23_24MAX = 0x09,
+ AUDIO_W_LEN_24_24MAX = 0x0b
+};
+
+#define I2S_CH_2 0x01
+#define TDM_CH_4 0x03
+#define TDM_CH_6 0x05
+#define TDM_CH_8 0x07
+
+#define MAX_DPCD_BUFFER_SIZE 16
+
+#define ONE_BLOCK_SIZE 128
+#define FOUR_BLOCK_SIZE (128 * 4)
+
+#define MAX_EDID_BLOCK 3
+#define EDID_TRY_CNT 3
+#define SUPPORT_PIXEL_CLOCK 300000
+
+struct s_edid_data {
+ int edid_block_num;
+ u8 edid_raw_data[FOUR_BLOCK_SIZE];
+};
+
+/***************** Display End *****************/
+
+struct anx7625_device_node {
+ struct device_node *mipi_dsi_host_node;
+ struct device_node *mipi_dpi_host_node;
+ struct device_node *panel_node;
+};
+
+struct anx7625_platform_data {
+ struct gpio_desc *gpio_p_on;
+ struct gpio_desc *gpio_reset;
+ struct drm_panel *panel;
+ int intp_irq;
+ u32 panel_flags;
+ u32 low_power_mode;
+ u32 dsi_supported;
+ u32 internal_panel;
+ u32 extcon_supported;
+ struct anx7625_device_node node;
+};
+
+struct anx7625_i2c_client {
+ struct i2c_client *tx_p0_client;
+ struct i2c_client *tx_p1_client;
+ struct i2c_client *tx_p2_client;
+ struct i2c_client *rx_p0_client;
+ struct i2c_client *rx_p1_client;
+ struct i2c_client *rx_p2_client;
+ struct i2c_client *tcpc_client;
+};
+
+struct anx7625_data {
+ struct anx7625_platform_data pdata;
+ atomic_t power_status;
+ atomic_t panel_power;
+ int hpd_status;
+ int hpd_high_cnt;
+ struct i2c_client *client;
+ struct anx7625_i2c_client i2c;
+ struct i2c_client *last_client;
+ struct s_edid_data slimport_edid_p;
+ struct work_struct work;
+ struct workqueue_struct *workqueue;
+ /* drm bridge mutex lock */
+ struct mutex lock;
+ char edid_block;
+ struct display_timing dt;
+ u8 display_timing_valid;
+ struct drm_bridge bridge;
+ u8 bridge_attached;
+ struct drm_connector connector;
+ struct mipi_dsi_device *dsi;
+ struct drm_dp_link link;
+ struct drm_display_mode vid_info;
+ struct notifier_block event_nb;
+ struct extcon_dev *extcon;
+ struct work_struct extcon_wq;
+};
+
+#endif /* __ANX7625_H__ */
--
2.7.4
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
^ permalink raw reply related [flat|nested] 3+ messages in thread