From: Marek Vasut <marek.vasut@gmail.com>
To: Simon Horman <horms@verge.net.au>
Cc: linux-pci@vger.kernel.org,
Marek Vasut <marek.vasut+renesas@gmail.com>,
Geert Uytterhoeven <geert+renesas@glider.be>,
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
Wolfram Sang <wsa@the-dreams.de>,
linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH V3 2/3] PCI: rcar: Do not abort on too many inbound dma-ranges
Date: Fri, 16 Aug 2019 19:41:37 +0200 [thread overview]
Message-ID: <e78c29b7-fe26-5fa6-3813-11a87ac811fa@gmail.com> (raw)
In-Reply-To: <20190816133816.4l463artoaswknj2@verge.net.au>
On 8/16/19 3:38 PM, Simon Horman wrote:
> On Fri, Aug 16, 2019 at 03:28:04PM +0200, Marek Vasut wrote:
>> On 8/16/19 3:23 PM, Simon Horman wrote:
>>> On Fri, Aug 09, 2019 at 07:57:40PM +0200, marek.vasut@gmail.com wrote:
>>>> From: Marek Vasut <marek.vasut+renesas@gmail.com>
>>>>
>>>> In case the "dma-ranges" DT property contains either too many ranges
>>>> or the range start address is unaligned in such a way that populating
>>>> the range into the controller requires multiple entries, a situation
>>>> may occur where all ranges cannot be loaded into the controller.
>>>>
>>>> Currently, the driver refuses to probe in such a situation. Relax this
>>>> behavior, load as many ranges as possible and warn if some ranges do
>>>> not fit anymore.
>>>
>>> What is the motivation for relaxing this?
>>
>> U-Boot can fill the ranges in properly now, the list would be longer in
>> such a case and the driver would fail to probe (because the list is
>> longer than what the hardware can support).
>
> Thanks, I think that would be worth adding to the changelog.
It does describe exactly what I just said -- if there are too many
ranges or they start in a way that cannot be easily fully programmed
into the HW, this patch applies.
> Regardless,
>
> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
>
--
Best regards,
Marek Vasut
next prev parent reply other threads:[~2019-08-16 17:50 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-09 17:57 [PATCH V3 1/3] PCI: rcar: Move the inbound index check marek.vasut
2019-08-09 17:57 ` [PATCH V3 2/3] PCI: rcar: Do not abort on too many inbound dma-ranges marek.vasut
2019-08-16 13:23 ` Simon Horman
2019-08-16 13:28 ` Marek Vasut
2019-08-16 13:38 ` Simon Horman
2019-08-16 17:41 ` Marek Vasut [this message]
2019-10-21 10:18 ` Andrew Murray
2019-10-26 18:03 ` Marek Vasut
2019-10-26 20:36 ` Andrew Murray
2019-10-26 21:06 ` Andrew Murray
2019-11-06 23:37 ` Marek Vasut
2019-11-07 14:19 ` Andrew Murray
2019-11-16 15:48 ` Marek Vasut
2019-11-18 18:42 ` Robin Murphy
2019-12-22 7:46 ` Marek Vasut
2019-10-16 15:00 ` Lorenzo Pieralisi
2019-10-16 15:10 ` Marek Vasut
2019-10-16 15:26 ` Lorenzo Pieralisi
2019-10-16 15:29 ` Marek Vasut
2019-10-16 16:18 ` Lorenzo Pieralisi
2019-10-16 18:12 ` Rob Herring
2019-10-16 18:17 ` Marek Vasut
2019-10-16 20:25 ` Rob Herring
2019-10-16 21:15 ` Marek Vasut
2019-10-16 22:26 ` Rob Herring
2019-10-16 22:33 ` Marek Vasut
2019-10-17 7:06 ` Geert Uytterhoeven
2019-10-17 10:55 ` Marek Vasut
2019-10-17 13:06 ` Robin Murphy
2019-10-17 14:00 ` Marek Vasut
2019-10-17 14:36 ` Rob Herring
2019-10-17 15:01 ` Marek Vasut
2019-10-18 9:53 ` Lorenzo Pieralisi
2019-10-18 12:22 ` Marek Vasut
2019-10-18 12:53 ` Robin Murphy
2019-10-18 14:26 ` Marek Vasut
2019-10-18 15:44 ` Robin Murphy
2019-10-18 16:44 ` Marek Vasut
2019-10-18 17:35 ` Robin Murphy
2019-10-18 18:44 ` Marek Vasut
2019-10-21 8:32 ` Geert Uytterhoeven
2019-11-19 12:10 ` Robin Murphy
2019-10-18 10:06 ` Andrew Murray
2019-10-18 10:17 ` Geert Uytterhoeven
2019-10-18 11:40 ` Andrew Murray
2019-08-09 17:57 ` [PATCH V3 3/3] PCI: rcar: Recalculate inbound range alignment for each controller entry marek.vasut
2019-10-21 10:39 ` Andrew Murray
2019-08-16 10:52 ` [PATCH V3 1/3] PCI: rcar: Move the inbound index check Lorenzo Pieralisi
2019-08-16 10:59 ` Marek Vasut
2019-08-16 11:10 ` Lorenzo Pieralisi
2019-10-15 20:14 ` Marek Vasut
2019-10-21 10:11 ` Andrew Murray
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e78c29b7-fe26-5fa6-3813-11a87ac811fa@gmail.com \
--to=marek.vasut@gmail.com \
--cc=geert+renesas@glider.be \
--cc=horms@verge.net.au \
--cc=linux-pci@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=marek.vasut+renesas@gmail.com \
--cc=wsa@the-dreams.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.