[PATCH v7 0/5] add imx8dxl evk support

[PATCH v7 0/5] add imx8dxl evk support

[Shenwei Wang]

i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.

The series of patches is to add the imx8dxl soc and its evk board
support.

changes in V7:
  - move the fec1 reset gpio into its phy node

changes in V6:
  - The V6 changes mainly respond to the comments from Shawn
  - Separate the V5 patch into SoC and Board commits
  - Remove the unnecessary properties of "max-frequency"
    in usdhc2 node
  - Remove the unnecessary properties of "clk_csr" in eqos node
  - Fix several coding style problems

changes in V5:
  - change the "scu" node name to "system-controller"
  - fix the typo in the comments for imx8dxl evk board

changes in V4:
  - move i2c/mmc/serial aliases from soc to board
  - correct the node names to follow the generic names recommendation
  - remove some unused nodes in the evk board dts

changes in V3:
  - re-order the commit sequence according to Krzysztof's feedback
  - correct the syntax and styple problems pointed by Krzysztof
    (Thank you for the detailed review, Krzysztof!)
  - remove the unused nodes in imx8dxl-evk.dts
  - dt_binding_check passed

Changes in V2:
  - removed the edma2 device node because the edma v3 driver hasn't been
    upstreamed yet.
  - removed the imx8dxl_cm4 alias to fix the compile error.
  - removed the extra blank lines at EOF.
  - dt_binding_check passed.

Shenwei Wang (5):
  dt-bindings: firmware: add missing resource IDs for imx8dxl
  dt-bindings: arm: imx: update fsl.yaml for imx8dxl
  arm64: dts: imx8: add a node label to ddr-pmu
  arm64: dts: freescale: add i.MX8DXL SoC support
  arm64: dts: freescale: add support for i.MX8DXL EVK board

 .../devicetree/bindings/arm/fsl.yaml          |   6 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../arm64/boot/dts/freescale/imx8-ss-ddr.dtsi |   2 +-
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 426 ++++++++++++++++++
 .../boot/dts/freescale/imx8dxl-ss-adma.dtsi   |  52 +++
 .../boot/dts/freescale/imx8dxl-ss-conn.dtsi   | 142 ++++++
 .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi    |   9 +
 .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi   |  74 +++
 arch/arm64/boot/dts/freescale/imx8dxl.dtsi    | 238 ++++++++++
 include/dt-bindings/firmware/imx/rsrc.h       |   7 +
 10 files changed, 956 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi

--
2.25.1

[PATCH v7 1/3] arm64: dts: imx8: add a node label to ddr-pmu

[Shenwei Wang]

The ddr-pmu on i.mx8dxl has a different interrupt number.
Add a node label to ddr-pmu so that it could be referred
and changed in i.mx8dxl dts.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
index 8b5cad4e2700..7d5183c6c5be 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
@@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 {
 	#size-cells = <1>;
 	ranges = <0x5c000000 0x0 0x5c000000 0x1000000>;
 
-	ddr-pmu@5c020000 {
+	ddr_pmu0: ddr-pmu@5c020000 {
 		compatible = "fsl,imx8-ddr-pmu";
 		reg = <0x5c020000 0x10000>;
 		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.25.1

[PATCH v7 1/5] dt-bindings: firmware: add missing resource IDs for imx8dxl

[Shenwei Wang]

Add the missing resource IDs for imx8dxl.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 include/dt-bindings/firmware/imx/rsrc.h | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/include/dt-bindings/firmware/imx/rsrc.h b/include/dt-bindings/firmware/imx/rsrc.h
index 43885056557c..1675de05ad33 100644
--- a/include/dt-bindings/firmware/imx/rsrc.h
+++ b/include/dt-bindings/firmware/imx/rsrc.h
@@ -37,10 +37,14 @@
 #define IMX_SC_R_DC_0_BLIT2		21
 #define IMX_SC_R_DC_0_BLIT_OUT		22
 #define IMX_SC_R_PERF			23
+#define IMX_SC_R_USB_1_PHY		24
 #define IMX_SC_R_DC_0_WARP		25
+#define IMX_SC_R_V2X_MU_0		26
+#define IMX_SC_R_V2X_MU_1		27
 #define IMX_SC_R_DC_0_VIDEO0		28
 #define IMX_SC_R_DC_0_VIDEO1		29
 #define IMX_SC_R_DC_0_FRAC0		30
+#define IMX_SC_R_V2X_MU_2		31
 #define IMX_SC_R_DC_0			32
 #define IMX_SC_R_GPU_2_PID0		33
 #define IMX_SC_R_DC_0_PLL_0		34
@@ -49,7 +53,10 @@
 #define IMX_SC_R_DC_1_BLIT1		37
 #define IMX_SC_R_DC_1_BLIT2		38
 #define IMX_SC_R_DC_1_BLIT_OUT		39
+#define IMX_SC_R_V2X_MU_3		40
+#define IMX_SC_R_V2X_MU_4		41
 #define IMX_SC_R_DC_1_WARP		42
+#define IMX_SC_R_SECVIO			44
 #define IMX_SC_R_DC_1_VIDEO0		45
 #define IMX_SC_R_DC_1_VIDEO1		46
 #define IMX_SC_R_DC_1_FRAC0		47
-- 
2.25.1

[PATCH v7 2/3] arm64: dts: freescale: add i.MX8DXL SoC support

[Shenwei Wang]

i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.

This patch adds the basic support for i.MX8DXL SoC.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
---
 .../boot/dts/freescale/imx8dxl-ss-adma.dtsi   |  52 ++++
 .../boot/dts/freescale/imx8dxl-ss-conn.dtsi   | 142 +++++++++++
 .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi    |   9 +
 .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi   |  74 ++++++
 arch/arm64/boot/dts/freescale/imx8dxl.dtsi    | 238 ++++++++++++++++++
 5 files changed, 515 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi

diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
new file mode 100644
index 000000000000..795d1d472fae
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+&audio_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&dma_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&i2c0 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c1 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c2 {
+	compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c3 {
+	compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart0 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart1 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart2 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart3 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
new file mode 100644
index 000000000000..69c4849f2132
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+/delete-node/ &enet1_lpcg;
+/delete-node/ &fec2;
+
+&conn_subsys {
+	conn_enet0_root_clk: clock-conn-enet0-root {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <250000000>;
+		clock-output-names = "conn_enet0_root_clk";
+	};
+
+	eqos: ethernet@5b050000 {
+		compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a";
+		reg = <0x5b050000 0x10000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "eth_wake_irq", "macirq";
+		clocks = <&eqos_lpcg IMX_LPCG_CLK_4>,
+			 <&eqos_lpcg IMX_LPCG_CLK_6>,
+			 <&eqos_lpcg IMX_LPCG_CLK_0>,
+			 <&eqos_lpcg IMX_LPCG_CLK_5>,
+			 <&eqos_lpcg IMX_LPCG_CLK_2>;
+		clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem";
+		assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <125000000>;
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+		status = "disabled";
+	};
+
+	usbotg2: usb@5b0e0000 {
+		compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb";
+		reg = <0x5b0e0000 0x200>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+		fsl,usbphy = <&usbphy2>;
+		fsl,usbmisc = <&usbmisc2 0>;
+		/*
+		 * usbotg1 and usbotg2 share one clcok.
+		 * scu firmware disables the access to the clock and keeps
+		 * it always on in case other core (M4) uses one of these.
+		 */
+		clocks = <&clk_dummy>;
+		ahb-burst-config = <0x0>;
+		tx-burst-size-dword = <0x10>;
+		rx-burst-size-dword = <0x10>;
+		#stream-id-cells = <1>;
+		power-domains = <&pd IMX_SC_R_USB_1>;
+		status = "disabled";
+
+		clk_dummy: clock-dummy {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+			clock-output-names = "clk_dummy";
+		};
+	};
+
+	usbmisc2: usbmisc@5b0e0200 {
+		#index-cells = <1>;
+		compatible = "fsl,imx7ulp-usbmisc";
+		reg = <0x5b0e0200 0x200>;
+	};
+
+	usbphy2: usbphy@0x5b110000 {
+		compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy";
+		reg = <0x5b110000 0x1000>;
+		clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>;
+		power-domains = <&pd IMX_SC_R_USB_1_PHY>;
+		status = "disabled";
+	};
+
+	eqos_lpcg: clock-controller@5b240000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b240000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&conn_enet0_root_clk>,
+			 <&conn_axi_clk>,
+			 <&conn_axi_clk>,
+			 <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
+			 <&conn_ipg_clk>;
+		clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>,
+				<IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>,
+				<IMX_LPCG_CLK_6>;
+		clock-output-names = "eqos_ptp",
+				     "eqos_mem_clk",
+				     "eqos_aclk",
+				     "eqos_clk",
+				     "eqos_csr_clk";
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+	};
+
+	usb2_2_lpcg: clock-controller@5b280000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b280000 0x10000>;
+		#clock-cells = <1>;
+		clock-indices = <IMX_LPCG_CLK_7>;
+		clocks = <&conn_ipg_clk>;
+		clock-output-names = "usboh3_2_phy_ipg_clk";
+		power-domains = <&pd IMX_SC_R_USB_1_PHY>;
+	};
+
+};
+
+&enet0_lpcg {
+	clocks = <&conn_enet0_root_clk>,
+		 <&conn_enet0_root_clk>,
+		 <&conn_axi_clk>,
+		 <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>,
+		 <&conn_ipg_clk>,
+		 <&conn_ipg_clk>;
+};
+
+&fec1 {
+	compatible = "fsl,imx8qm-fec";
+	interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+	assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>;
+	assigned-clock-rates = <125000000>;
+};
+
+&usdhc1 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc2 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc3 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
new file mode 100644
index 000000000000..550f513708d8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2020 NXP
+ */
+
+&ddr_pmu0 {
+	compatible = "fsl,imx8-ddr-pmu";
+	interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
new file mode 100644
index 000000000000..815bd987b09b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+&lsio_gpio0 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio1 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio2 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio3 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio4 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio5 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio6 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio7 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu0 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu1 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu2 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu3 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu4 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu5 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
new file mode 100644
index 000000000000..5ddbda0b4def
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+#include <dt-bindings/clock/imx8-clock.h>
+#include <dt-bindings/firmware/imx/rsrc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/pads-imx8dxl.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &eqos;
+		gpio0 = &lsio_gpio0;
+		gpio1 = &lsio_gpio1;
+		gpio2 = &lsio_gpio2;
+		gpio3 = &lsio_gpio3;
+		gpio4 = &lsio_gpio4;
+		gpio5 = &lsio_gpio5;
+		gpio6 = &lsio_gpio6;
+		gpio7 = &lsio_gpio7;
+		mu1 = &lsio_mu1;
+	};
+
+	cpus: cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		/* We have 1 clusters with 2 Cortex-A35 cores */
+		A35_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_L2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	a35_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-900000000 {
+			opp-hz = /bits/ 64 <900000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
+		};
+	};
+
+	gic: interrupt-controller@51a00000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */
+		      <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_reserved: dsp@92400000 {
+			reg = <0 0x92400000 0 0x2000000>;
+			no-map;
+		};
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	system-controller {
+		compatible = "fsl,imx-scu";
+		mbox-names = "tx0",
+			     "rx0",
+			     "gip3";
+		mboxes = <&lsio_mu1 0 0
+			  &lsio_mu1 1 0
+			  &lsio_mu1 3 3>;
+
+		pd: power-controller {
+			compatible = "fsl,scu-pd";
+			#power-domain-cells = <1>;
+			wakeup-irq = <160 163 235 236 237 228 229 230 231 238
+				     239 240 166 169>;
+		};
+
+		clk: clock-controller {
+			compatible = "fsl,imx8dxl-clk", "fsl,scu-clk";
+			#clock-cells = <2>;
+			clocks = <&xtal32k &xtal24m>;
+			clock-names = "xtal_32KHz", "xtal_24Mhz";
+		};
+
+		iomuxc: pinctrl {
+			compatible = "fsl,imx8dxl-iomuxc";
+		};
+
+		ocotp: ocotp {
+			compatible = "fsl,imx8qxp-scu-ocotp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			fec_mac0: mac@2c4 {
+				reg = <0x2c4 6>;
+			};
+
+			fec_mac1: mac@2c6 {
+				reg = <0x2c6 6>;
+			};
+		};
+
+		rtc: rtc {
+			compatible = "fsl,imx8qxp-sc-rtc";
+		};
+
+		sc_pwrkey: keys {
+			compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key";
+			linux,keycode = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		watchdog {
+			compatible = "fsl,imx-sc-wdt";
+			timeout-sec = <60>;
+		};
+
+		tsens: thermal-sensor {
+			compatible = "fsl,imx-sc-thermal";
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */
+	};
+
+	thermal_zones: thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <107000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <127000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	/* The two values below cannot be changed by the board */
+	xtal32k: clock-xtal32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xtal_32KHz";
+	};
+
+	xtal24m: clock-xtal24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal_24MHz";
+	};
+
+	/* sorted in register address */
+	#include "imx8-ss-adma.dtsi"
+	#include "imx8-ss-conn.dtsi"
+	#include "imx8-ss-ddr.dtsi"
+	#include "imx8-ss-lsio.dtsi"
+};
+
+#include "imx8dxl-ss-adma.dtsi"
+#include "imx8dxl-ss-conn.dtsi"
+#include "imx8dxl-ss-lsio.dtsi"
+#include "imx8dxl-ss-ddr.dtsi"
-- 
2.25.1

[PATCH v7 2/5] dt-bindings: arm: imx: update fsl.yaml for imx8dxl

[Shenwei Wang]

i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 7431579ab0e8..4f4c9c0a1315 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1034,6 +1034,12 @@ properties:
               - toradex,colibri-imx8x     # Colibri iMX8X Modules
           - const: fsl,imx8qxp
 
+      - description: i.MX8DXL based Boards
+        items:
+          - enum:
+              - fsl,imx8dxl-evk           # i.MX8DXL EVK Board
+          - const: fsl,imx8dxl
+
       - description: i.MX8QXP Boards with Toradex Coilbri iMX8X Modules
         items:
           - enum:
-- 
2.25.1

[PATCH v7 3/3] arm64: dts: freescale: add support for i.MX8DXL EVK board

[Shenwei Wang]

This is to support the EVK (Evaluation Kit Board) for the i.MX8DXL.
The patch has enabled the serial console, SD/EMMC interface, and
the eqos and fec ethernet network.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 426 ++++++++++++++++++
 2 files changed, 427 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 8bf7f7ecebaa..2741205efe84 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-85bb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb
 
+dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
new file mode 100644
index 000000000000..868c75945af3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8dxl.dtsi"
+
+/ {
+	model = "Freescale i.MX8DXL EVK";
+	compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl";
+
+	aliases {
+		i2c2 = &i2c2;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		serial0 = &lpuart0;
+	};
+
+	chosen {
+		stdout-path = &lpuart0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000 0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * Memory reserved for optee usage. Please do not use.
+		 * This will be automatically added to dtb if OP-TEE is installed.
+		 * optee@96000000 {
+		 *     reg = <0 0x96000000 0 0x2000000>;
+		 *     no-map;
+		 * };
+		 */
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0 0x14000000>;
+			alloc-ranges = <0 0x98000000 0 0x14000000>;
+			linux,cma-default;
+		};
+	};
+
+	mux3_en: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "mux3_en";
+		gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	reg_fec1_sel: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec1_supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		status = "disabled";
+	};
+
+	reg_fec1_io: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec1_io_supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&max7322 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		status = "disabled";
+	};
+
+	reg_usdhc2_vmmc: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SD1_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		off-on-delay-us = <3480>;
+	};
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	nvmem-cells = <&fec_mac1>;
+	nvmem-cell-names = "mac-address";
+	snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>;
+	snps,reset-delays-us = <10 20 200000>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			eee-broken-1000t;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio0>;
+
+			vddio0: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+/*
+ * fec1 shares the some PINs with usdhc2.
+ * by default usdhc2 is enabled in this dts.
+ * Please disable usdhc2 to enable fec1
+ */
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-txid";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	rx-internal-delay-ps = <2000>;
+	nvmem-cells = <&fec_mac0>;
+	nvmem-cell-names = "mac-address";
+	status = "disabled";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio1>;
+
+			vddio1: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pca6416_1: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca6416_2: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9548_1: i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			max7322: gpio@68 {
+				compatible = "maxim,max7322";
+				reg = <0x68>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+	};
+};
+
+&lpuart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+&lsio_gpio4 {
+	status = "okay";
+};
+
+&lsio_gpio5 {
+	status = "okay";
+};
+
+&thermal_zones {
+	pmic-thermal0 {
+		polling-delay-passive = <250>;
+		polling-delay = <2000>;
+		thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
+
+		trips {
+			pmic_alert0: trip0 {
+				temperature = <110000>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+
+			pmic_crit0: trip1 {
+				temperature = <125000>;
+				hysteresis = <2000>;
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&pmic_alert0>;
+				cooling-device =
+					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD	0x000514a0
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD	0x000014a0
+			IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1		0x0600004c
+			IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN	0x0600004c
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR		0x00000021
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR		0x00000021
+		>;
+	};
+
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			IMX8DXL_ENET0_MDC_CONN_EQOS_MDC				0x06000020
+			IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO			0x06000020
+			IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3		0x06000020
+			IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL	0x06000020
+			IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3		0x06000020
+			IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL	0x06000020
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD		0x000014a0
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD		0x000014a0
+			IMX8DXL_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+			IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+			IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3		0x00000060
+			IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x00000060
+			IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3		0x00000060
+			IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x00000060
+		>;
+	};
+
+	pinctrl_lpspi3: lpspi3grp {
+		fsl,pins = <
+			IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK		0x6000040
+			IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO		0x6000040
+			IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI		0x6000040
+			IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1		0x6000040
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA		0x06000021
+			IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL		0x06000021
+		>;
+	};
+
+	pinctrl_cm40_lpuart: cm40lpuartgrp {
+		fsl,pins = <
+			IMX8DXL_ADC_IN2_M40_UART0_RX		0x06000020
+			IMX8DXL_ADC_IN3_M40_UART0_TX		0x06000020
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA		0x06000021
+			IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL		0x06000021
+		>;
+	};
+
+	pinctrl_lpuart0: lpuart0grp {
+		fsl,pins = <
+			IMX8DXL_UART0_RX_ADMA_UART0_RX		0x06000020
+			IMX8DXL_UART0_TX_ADMA_UART0_TX		0x06000020
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK	0x06000041
+			IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD	0x00000021
+			IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+			IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+			IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+			IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+			IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+			IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+			IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+			IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+			IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30	0x00000040 /* RESET_B */
+			IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00	0x00000021 /* WP */
+			IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01	0x00000021 /* CD */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK		0x06000041
+			IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3	0x00000021
+			IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT	0x00000021
+		>;
+	};
+};
-- 
2.25.1

[PATCH v7 3/5] arm64: dts: imx8: add a node label to ddr-pmu

[Shenwei Wang]

The ddr-pmu on i.mx8dxl has a different interrupt number.
Add a node label to ddr-pmu so that it could be referred
and changed in i.mx8dxl dts.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
index 8b5cad4e2700..7d5183c6c5be 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
@@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 {
 	#size-cells = <1>;
 	ranges = <0x5c000000 0x0 0x5c000000 0x1000000>;
 
-	ddr-pmu@5c020000 {
+	ddr_pmu0: ddr-pmu@5c020000 {
 		compatible = "fsl,imx8-ddr-pmu";
 		reg = <0x5c020000 0x10000>;
 		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.25.1

[PATCH v7 4/5] arm64: dts: freescale: add i.MX8DXL SoC support

[Shenwei Wang]

i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.

This patch adds the basic support for i.MX8DXL SoC.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
---
 .../boot/dts/freescale/imx8dxl-ss-adma.dtsi   |  52 ++++
 .../boot/dts/freescale/imx8dxl-ss-conn.dtsi   | 142 +++++++++++
 .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi    |   9 +
 .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi   |  74 ++++++
 arch/arm64/boot/dts/freescale/imx8dxl.dtsi    | 238 ++++++++++++++++++
 5 files changed, 515 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi

diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
new file mode 100644
index 000000000000..795d1d472fae
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+&audio_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&dma_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&i2c0 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c1 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c2 {
+	compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c3 {
+	compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart0 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart1 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart2 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart3 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
new file mode 100644
index 000000000000..69c4849f2132
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+/delete-node/ &enet1_lpcg;
+/delete-node/ &fec2;
+
+&conn_subsys {
+	conn_enet0_root_clk: clock-conn-enet0-root {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <250000000>;
+		clock-output-names = "conn_enet0_root_clk";
+	};
+
+	eqos: ethernet@5b050000 {
+		compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a";
+		reg = <0x5b050000 0x10000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "eth_wake_irq", "macirq";
+		clocks = <&eqos_lpcg IMX_LPCG_CLK_4>,
+			 <&eqos_lpcg IMX_LPCG_CLK_6>,
+			 <&eqos_lpcg IMX_LPCG_CLK_0>,
+			 <&eqos_lpcg IMX_LPCG_CLK_5>,
+			 <&eqos_lpcg IMX_LPCG_CLK_2>;
+		clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem";
+		assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <125000000>;
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+		status = "disabled";
+	};
+
+	usbotg2: usb@5b0e0000 {
+		compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb";
+		reg = <0x5b0e0000 0x200>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+		fsl,usbphy = <&usbphy2>;
+		fsl,usbmisc = <&usbmisc2 0>;
+		/*
+		 * usbotg1 and usbotg2 share one clcok.
+		 * scu firmware disables the access to the clock and keeps
+		 * it always on in case other core (M4) uses one of these.
+		 */
+		clocks = <&clk_dummy>;
+		ahb-burst-config = <0x0>;
+		tx-burst-size-dword = <0x10>;
+		rx-burst-size-dword = <0x10>;
+		#stream-id-cells = <1>;
+		power-domains = <&pd IMX_SC_R_USB_1>;
+		status = "disabled";
+
+		clk_dummy: clock-dummy {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+			clock-output-names = "clk_dummy";
+		};
+	};
+
+	usbmisc2: usbmisc@5b0e0200 {
+		#index-cells = <1>;
+		compatible = "fsl,imx7ulp-usbmisc";
+		reg = <0x5b0e0200 0x200>;
+	};
+
+	usbphy2: usbphy@0x5b110000 {
+		compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy";
+		reg = <0x5b110000 0x1000>;
+		clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>;
+		power-domains = <&pd IMX_SC_R_USB_1_PHY>;
+		status = "disabled";
+	};
+
+	eqos_lpcg: clock-controller@5b240000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b240000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&conn_enet0_root_clk>,
+			 <&conn_axi_clk>,
+			 <&conn_axi_clk>,
+			 <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
+			 <&conn_ipg_clk>;
+		clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>,
+				<IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>,
+				<IMX_LPCG_CLK_6>;
+		clock-output-names = "eqos_ptp",
+				     "eqos_mem_clk",
+				     "eqos_aclk",
+				     "eqos_clk",
+				     "eqos_csr_clk";
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+	};
+
+	usb2_2_lpcg: clock-controller@5b280000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b280000 0x10000>;
+		#clock-cells = <1>;
+		clock-indices = <IMX_LPCG_CLK_7>;
+		clocks = <&conn_ipg_clk>;
+		clock-output-names = "usboh3_2_phy_ipg_clk";
+		power-domains = <&pd IMX_SC_R_USB_1_PHY>;
+	};
+
+};
+
+&enet0_lpcg {
+	clocks = <&conn_enet0_root_clk>,
+		 <&conn_enet0_root_clk>,
+		 <&conn_axi_clk>,
+		 <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>,
+		 <&conn_ipg_clk>,
+		 <&conn_ipg_clk>;
+};
+
+&fec1 {
+	compatible = "fsl,imx8qm-fec";
+	interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+	assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>;
+	assigned-clock-rates = <125000000>;
+};
+
+&usdhc1 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc2 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc3 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
new file mode 100644
index 000000000000..550f513708d8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2020 NXP
+ */
+
+&ddr_pmu0 {
+	compatible = "fsl,imx8-ddr-pmu";
+	interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
new file mode 100644
index 000000000000..815bd987b09b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+&lsio_gpio0 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio1 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio2 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio3 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio4 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio5 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio6 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio7 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu0 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu1 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu2 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu3 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu4 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu5 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
new file mode 100644
index 000000000000..5ddbda0b4def
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+#include <dt-bindings/clock/imx8-clock.h>
+#include <dt-bindings/firmware/imx/rsrc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/pads-imx8dxl.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &eqos;
+		gpio0 = &lsio_gpio0;
+		gpio1 = &lsio_gpio1;
+		gpio2 = &lsio_gpio2;
+		gpio3 = &lsio_gpio3;
+		gpio4 = &lsio_gpio4;
+		gpio5 = &lsio_gpio5;
+		gpio6 = &lsio_gpio6;
+		gpio7 = &lsio_gpio7;
+		mu1 = &lsio_mu1;
+	};
+
+	cpus: cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		/* We have 1 clusters with 2 Cortex-A35 cores */
+		A35_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_L2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	a35_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-900000000 {
+			opp-hz = /bits/ 64 <900000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
+		};
+	};
+
+	gic: interrupt-controller@51a00000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */
+		      <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_reserved: dsp@92400000 {
+			reg = <0 0x92400000 0 0x2000000>;
+			no-map;
+		};
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	system-controller {
+		compatible = "fsl,imx-scu";
+		mbox-names = "tx0",
+			     "rx0",
+			     "gip3";
+		mboxes = <&lsio_mu1 0 0
+			  &lsio_mu1 1 0
+			  &lsio_mu1 3 3>;
+
+		pd: power-controller {
+			compatible = "fsl,scu-pd";
+			#power-domain-cells = <1>;
+			wakeup-irq = <160 163 235 236 237 228 229 230 231 238
+				     239 240 166 169>;
+		};
+
+		clk: clock-controller {
+			compatible = "fsl,imx8dxl-clk", "fsl,scu-clk";
+			#clock-cells = <2>;
+			clocks = <&xtal32k &xtal24m>;
+			clock-names = "xtal_32KHz", "xtal_24Mhz";
+		};
+
+		iomuxc: pinctrl {
+			compatible = "fsl,imx8dxl-iomuxc";
+		};
+
+		ocotp: ocotp {
+			compatible = "fsl,imx8qxp-scu-ocotp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			fec_mac0: mac@2c4 {
+				reg = <0x2c4 6>;
+			};
+
+			fec_mac1: mac@2c6 {
+				reg = <0x2c6 6>;
+			};
+		};
+
+		rtc: rtc {
+			compatible = "fsl,imx8qxp-sc-rtc";
+		};
+
+		sc_pwrkey: keys {
+			compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key";
+			linux,keycode = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		watchdog {
+			compatible = "fsl,imx-sc-wdt";
+			timeout-sec = <60>;
+		};
+
+		tsens: thermal-sensor {
+			compatible = "fsl,imx-sc-thermal";
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */
+	};
+
+	thermal_zones: thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <107000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <127000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	/* The two values below cannot be changed by the board */
+	xtal32k: clock-xtal32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xtal_32KHz";
+	};
+
+	xtal24m: clock-xtal24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal_24MHz";
+	};
+
+	/* sorted in register address */
+	#include "imx8-ss-adma.dtsi"
+	#include "imx8-ss-conn.dtsi"
+	#include "imx8-ss-ddr.dtsi"
+	#include "imx8-ss-lsio.dtsi"
+};
+
+#include "imx8dxl-ss-adma.dtsi"
+#include "imx8dxl-ss-conn.dtsi"
+#include "imx8dxl-ss-lsio.dtsi"
+#include "imx8dxl-ss-ddr.dtsi"
-- 
2.25.1

[PATCH v7 5/5] arm64: dts: freescale: add support for i.MX8DXL EVK board

[Shenwei Wang]

This is to support the EVK (Evaluation Kit Board) for the i.MX8DXL.
The patch has enabled the serial console, SD/EMMC interface, and
the eqos and fec ethernet network.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 426 ++++++++++++++++++
 2 files changed, 427 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 8bf7f7ecebaa..2741205efe84 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-85bb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb
 
+dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
new file mode 100644
index 000000000000..868c75945af3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8dxl.dtsi"
+
+/ {
+	model = "Freescale i.MX8DXL EVK";
+	compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl";
+
+	aliases {
+		i2c2 = &i2c2;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		serial0 = &lpuart0;
+	};
+
+	chosen {
+		stdout-path = &lpuart0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000 0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * Memory reserved for optee usage. Please do not use.
+		 * This will be automatically added to dtb if OP-TEE is installed.
+		 * optee@96000000 {
+		 *     reg = <0 0x96000000 0 0x2000000>;
+		 *     no-map;
+		 * };
+		 */
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0 0x14000000>;
+			alloc-ranges = <0 0x98000000 0 0x14000000>;
+			linux,cma-default;
+		};
+	};
+
+	mux3_en: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "mux3_en";
+		gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	reg_fec1_sel: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec1_supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		status = "disabled";
+	};
+
+	reg_fec1_io: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec1_io_supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&max7322 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		status = "disabled";
+	};
+
+	reg_usdhc2_vmmc: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SD1_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		off-on-delay-us = <3480>;
+	};
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	nvmem-cells = <&fec_mac1>;
+	nvmem-cell-names = "mac-address";
+	snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>;
+	snps,reset-delays-us = <10 20 200000>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			eee-broken-1000t;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio0>;
+
+			vddio0: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+/*
+ * fec1 shares the some PINs with usdhc2.
+ * by default usdhc2 is enabled in this dts.
+ * Please disable usdhc2 to enable fec1
+ */
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-txid";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	rx-internal-delay-ps = <2000>;
+	nvmem-cells = <&fec_mac0>;
+	nvmem-cell-names = "mac-address";
+	status = "disabled";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio1>;
+
+			vddio1: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pca6416_1: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca6416_2: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9548_1: i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			max7322: gpio@68 {
+				compatible = "maxim,max7322";
+				reg = <0x68>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+	};
+};
+
+&lpuart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+&lsio_gpio4 {
+	status = "okay";
+};
+
+&lsio_gpio5 {
+	status = "okay";
+};
+
+&thermal_zones {
+	pmic-thermal0 {
+		polling-delay-passive = <250>;
+		polling-delay = <2000>;
+		thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
+
+		trips {
+			pmic_alert0: trip0 {
+				temperature = <110000>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+
+			pmic_crit0: trip1 {
+				temperature = <125000>;
+				hysteresis = <2000>;
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&pmic_alert0>;
+				cooling-device =
+					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD	0x000514a0
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD	0x000014a0
+			IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1		0x0600004c
+			IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN	0x0600004c
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR		0x00000021
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR		0x00000021
+		>;
+	};
+
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			IMX8DXL_ENET0_MDC_CONN_EQOS_MDC				0x06000020
+			IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO			0x06000020
+			IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3		0x06000020
+			IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL	0x06000020
+			IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3		0x06000020
+			IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL	0x06000020
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD		0x000014a0
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD		0x000014a0
+			IMX8DXL_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+			IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+			IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3		0x00000060
+			IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x00000060
+			IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3		0x00000060
+			IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x00000060
+		>;
+	};
+
+	pinctrl_lpspi3: lpspi3grp {
+		fsl,pins = <
+			IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK		0x6000040
+			IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO		0x6000040
+			IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI		0x6000040
+			IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1		0x6000040
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA		0x06000021
+			IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL		0x06000021
+		>;
+	};
+
+	pinctrl_cm40_lpuart: cm40lpuartgrp {
+		fsl,pins = <
+			IMX8DXL_ADC_IN2_M40_UART0_RX		0x06000020
+			IMX8DXL_ADC_IN3_M40_UART0_TX		0x06000020
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA		0x06000021
+			IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL		0x06000021
+		>;
+	};
+
+	pinctrl_lpuart0: lpuart0grp {
+		fsl,pins = <
+			IMX8DXL_UART0_RX_ADMA_UART0_RX		0x06000020
+			IMX8DXL_UART0_TX_ADMA_UART0_TX		0x06000020
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK	0x06000041
+			IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD	0x00000021
+			IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+			IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+			IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+			IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+			IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+			IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+			IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+			IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+			IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30	0x00000040 /* RESET_B */
+			IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00	0x00000021 /* WP */
+			IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01	0x00000021 /* CD */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK		0x06000041
+			IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3	0x00000021
+			IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT	0x00000021
+		>;
+	};
+};
-- 
2.25.1