intel-gfx.lists.freedesktop.org archive mirror
 help / color / mirror / Atom feed
From: Chris Wilson <chris@chris-wilson.co.uk>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: intel-gfx@lists.freedesktop.org
Subject: [PATCH] drm/i915: Use TILECTL on SNB to detect swizzle mode
Date: Fri, 11 Feb 2011 09:25:17 +0000	[thread overview]
Message-ID: <1297416317-9476-1-git-send-email-chris@chris-wilson.co.uk> (raw)

We're meant to set this bit based on DRAM configuration...

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
---

Jesse, does this suggest anything unusual for TILECLT on your weird system?
Also do you know which DRAM config bits it is referring to?
-Chris

---
 drivers/gpu/drm/i915/i915_gem_tiling.c |   29 ++++++++++++++++++++++++++++-
 drivers/gpu/drm/i915/i915_reg.h        |    3 +++
 drivers/gpu/drm/i915/intel_display.c   |    8 ++++++--
 3 files changed, 37 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_gem_tiling.c b/drivers/gpu/drm/i915/i915_gem_tiling.c
index 22a32b9..bc19fb2 100644
--- a/drivers/gpu/drm/i915/i915_gem_tiling.c
+++ b/drivers/gpu/drm/i915/i915_gem_tiling.c
@@ -92,7 +92,34 @@ i915_gem_detect_bit_6_swizzle(struct drm_device *dev)
 	uint32_t swizzle_x = I915_BIT_6_SWIZZLE_UNKNOWN;
 	uint32_t swizzle_y = I915_BIT_6_SWIZZLE_UNKNOWN;
 
-	if (IS_GEN5(dev) || IS_GEN6(dev)) {
+	if (IS_GEN6(dev)) {
+		/* TILECTL 0x10100 (uncore):
+		 * [1:0] Address Swizzling for Tiled-Surfaces (SWZCTL):
+		 * This register location is updated via GFX Driver prior to
+		 * enabling DRAM accesses.  The Driver needs to obtain the need
+		 * for memory address swizzling via DRAM configuration registers
+		 * and set the following bits.
+		 *
+		 * 00b - No Address Swizzling
+		 * 01b - Address bit [6] needs to be swizzled for tiled surfaces
+		 * 10b - Reserved
+		 * 11b - Reserved
+		 */
+		printk(KERN_ERR "tilectl = %x\n", I915_READ(GEN6_TILECTL));
+		switch (I915_READ(GEN6_TILECTL) & 0x3) {
+		default:
+			DRM_ERROR("unknown swizzle mode for tiled surfaces: %x\n",
+				  I915_READ(GEN6_TILECTL));
+		case 0:
+			swizzle_x = I915_BIT_6_SWIZZLE_NONE;
+			swizzle_y = I915_BIT_6_SWIZZLE_NONE;
+			break;
+		case 1:
+			swizzle_x = I915_BIT_6_SWIZZLE_9_10;
+			swizzle_y = I915_BIT_6_SWIZZLE_9;
+			break;
+		}
+	} else if (IS_GEN5(dev)) {
 		/* On Ironlake whatever DRAM config, GPU always do
 		 * same swizzling setup.
 		 */
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 15d94c6..49bae1a 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -2781,8 +2781,11 @@
 
 #define DISP_ARB_CTL	0x45000
 #define  DISP_TILE_SURFACE_SWIZZLING	(1<<13)
+#define  DISP_TILE_MASK			(3<<13)
 #define  DISP_FBC_WM_DIS		(1<<15)
 
+#define GEN6_TILECTL 0x101000
+
 /* PCH */
 
 /* south display engine interrupt */
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 3b00653..94b6030 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -4457,10 +4457,14 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 
 	intel_wait_for_vblank(dev, pipe);
 
+	/* enable address swizzle for tiling scanout */
 	if (IS_GEN5(dev)) {
-		/* enable address swizzle for tiling buffer */
-		temp = I915_READ(DISP_ARB_CTL);
+		temp = I915_READ(DISP_ARB_CTL) & ~DISP_TILE_MASK;
 		I915_WRITE(DISP_ARB_CTL, temp | DISP_TILE_SURFACE_SWIZZLING);
+	} else if (IS_GEN6 (dev)) {
+		temp = I915_READ(DISP_ARB_CTL) & ~DISP_TILE_MASK;
+		temp |= (I915_READ(GEN6_TILECTL) & 0x3) << 13;
+		I915_WRITE(DISP_ARB_CTL, temp);
 	}
 
 	I915_WRITE(DSPCNTR(plane), dspcntr);
-- 
1.7.2.3

             reply	other threads:[~2011-02-11  9:25 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-02-11  9:25 Chris Wilson [this message]
2011-02-11 17:42 ` [PATCH] drm/i915: Use TILECTL on SNB to detect swizzle mode Jesse Barnes

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1297416317-9476-1-git-send-email-chris@chris-wilson.co.uk \
    --to=chris@chris-wilson.co.uk \
    --cc=intel-gfx@lists.freedesktop.org \
    --cc=jbarnes@virtuousgeek.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).