[PATCH v3 0/2] Switch MSR_MISC_FEATURES_ENABLES and one optimization

[PATCH v3 0/2] Switch MSR_MISC_FEATURES_ENABLES and one optimization

[Xiaoyao Li]

Patch 1 switches MSR_MISC_FEATURES_ENABLE between host and guest to avoid
cpuid faulting and ring3mwait of host leaking to guest. Because cpuid
faulting eanbled in host may potentially cause guest boot failure, and kvm
doesn't expose ring3mwait to guest yet, it should be leaked to guest.

Patch 2 optimizes the switch of MSR_MISC_FEATURES_ENABLES by avoiding WRMSR
whenever possible to save cycles.

==changelog==
v2->v3:
- use msr_misc_features_shadow instead of reading hardware msr, from Sean
Christopherson
- avoid WRMSR whenever possible, from Sean Christopherson.

v1->v2: 
- move the save/restore of cpuid faulting bit to
vmx_prepare_swich_to_guest/vmx_prepare_swich_to_host to avoid every
vmentry RDMSR, based on Paolo's comment.

Xiaoyao Li (2):
  kvm/vmx: Switch MSR_MISC_FEATURES_ENABLES between host and guest
  x86/vmx: optimize MSR_MISC_FEATURES_ENABLES switch

 arch/x86/include/asm/kvm_host.h |  2 ++
 arch/x86/kernel/process.c       |  1 +
 arch/x86/kvm/vmx/vmx.c          | 31 +++++++++++++++++++++++++++++++
 arch/x86/kvm/x86.c              | 15 ++++++++++++---
 4 files changed, 46 insertions(+), 3 deletions(-)

-- 
2.19.1

[PATCH v3 1/2] kvm/vmx: Switch MSR_MISC_FEATURES_ENABLES between host and guest

[Xiaoyao Li]

There are two defined bits in MSR_MISC_FEATURES_ENABLES, bit 0 for cpuid
faulting and bit 1 for ring3mwait.

== cpuid Faulting ==
cpuid faulting is a feature about CPUID instruction. When cpuid faulting
is enabled, all execution of the CPUID instruction outside system-management
mode (SMM) cause a general-protection (#GP) if the CPL > 0.

About this feature, detailed information can be found at
https://www.intel.com/content/dam/www/public/us/en/documents/application-notes/virtualization-technology-flexmigration-application-note.pdf

Current KVM provides software emulation of this feature for guest.
However, because cpuid faulting takes higher priority over CPUID vm exit (Intel
SDM vol3.25.1.1), there is a risk of leaking cpuid faulting to guest when host
enables it. If host enables cpuid faulting by setting the bit 0 of
MSR_MISC_FEATURES_ENABLES, it will pass to guest since there is no switch of
MSR_MISC_FEATURES_ENABLES yet. As a result, when guest calls CPUID instruction
in CPL > 0, it will generate a #GP instead of CPUID vm eixt.

This issue will cause guest boot failure when guest uses *modprobe*
to load modules. *modprobe* calls CPUID instruction, thus causing #GP in
guest. Since there is no handling of cpuid faulting in #GP handler, guest
fails boot.

== ring3mwait ==
Ring3mwait is a Xeon-Phi Product Family x200 series specific feature,
which allows the MONITOR and MWAIT instructions to be executed in rings
other than ring 0. The feature can be enabled by setting bit 1 in
MSR_MISC_FEATURES_ENABLES. The register can also be read to determine
whether the instructions are enabled at other than ring 0.

About this feature, description can be found at
https://software.intel.com/en-us/blogs/2016/10/06/intel-xeon-phi-product-family-x200-knl-user-mode-ring-3-monitor-and-mwait

Current kvm doesn't expose feature ring3mwait to guest. However, there is also
a risk of leaking ring3mwait to guest if host enables it since there is no
switch of MSR_MISC_FEATURES_ENABLES.

== solution ==
>From above analysis, both cpuid faulting and ring3mwait can be leaked to guest.
To fix this issue, MSR_MISC_FEATURES_ENABLES should be switched between host
and guest. Since MSR_MISC_FEATURES_ENABLES is intel-specific, this patch
implement the switching only in vmx.

For the reason that kvm provides the software emulation of cpuid faulting and
kvm doesn't expose ring3mwait to guest. MSR_MISC_FEATURES_ENABLES can be just
cleared to zero for guest when any of the features is enabled in host.

Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
---
 arch/x86/kernel/process.c |  1 +
 arch/x86/kvm/vmx/vmx.c    | 24 ++++++++++++++++++++++++
 2 files changed, 25 insertions(+)

diff --git a/arch/x86/kernel/process.c b/arch/x86/kernel/process.c
index 1bba1a3c0b01..94a566e79b6c 100644
--- a/arch/x86/kernel/process.c
+++ b/arch/x86/kernel/process.c
@@ -191,6 +191,7 @@ int set_tsc_mode(unsigned int val)
 }
 
 DEFINE_PER_CPU(u64, msr_misc_features_shadow);
+EXPORT_PER_CPU_SYMBOL_GPL(msr_misc_features_shadow);
 
 static void set_cpuid_faulting(bool on)
 {
diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
index 270c6566fd5a..65aa947947ba 100644
--- a/arch/x86/kvm/vmx/vmx.c
+++ b/arch/x86/kvm/vmx/vmx.c
@@ -1031,6 +1031,16 @@ static void pt_guest_exit(struct vcpu_vmx *vmx)
 	wrmsrl(MSR_IA32_RTIT_CTL, vmx->pt_desc.host.ctl);
 }
 
+static void vmx_prepare_guest_misc_features_enables(struct vcpu_vmx *vmx)
+{
+	u64 msrval = this_cpu_read(msr_misc_features_shadow);
+
+	if (!msrval)
+		return;
+
+	wrmsrl(MSR_MISC_FEATURES_ENABLES, 0ULL);
+}
+
 void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
 {
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
@@ -1064,6 +1074,8 @@ void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
 	vmx->loaded_cpu_state = vmx->loaded_vmcs;
 	host_state = &vmx->loaded_cpu_state->host_state;
 
+	vmx_prepare_guest_misc_features_enables(vmx);
+
 	/*
 	 * Set host fs and gs selectors.  Unfortunately, 22.2.3 does not
 	 * allow segment selectors with cpl > 0 or ti == 1.
@@ -1120,6 +1132,16 @@ void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
 	}
 }
 
+static void vmx_load_host_misc_features_enables(struct vcpu_vmx *vmx)
+{
+	u64 msrval = this_cpu_read(msr_misc_features_shadow);
+
+	if (!msrval)
+		return;
+
+	wrmsrl(MSR_MISC_FEATURES_ENABLES, msrval);
+}
+
 static void vmx_prepare_switch_to_host(struct vcpu_vmx *vmx)
 {
 	struct vmcs_host_state *host_state;
@@ -1133,6 +1155,8 @@ static void vmx_prepare_switch_to_host(struct vcpu_vmx *vmx)
 	++vmx->vcpu.stat.host_state_reload;
 	vmx->loaded_cpu_state = NULL;
 
+	vmx_load_host_misc_features_enables(vmx);
+
 #ifdef CONFIG_X86_64
 	rdmsrl(MSR_KERNEL_GS_BASE, vmx->msr_guest_kernel_gs_base);
 #endif
-- 
2.19.1

[PATCH v3 2/2] x86/vmx: optimize MSR_MISC_FEATURES_ENABLES switch

[Xiaoyao Li]

KVM needs to switch MSR_MISC_FEATURES_ENABLES between host and guest in
every pcpu/vcpu context switch. Since WRMSR is expensive, this patch tries
to save cycles by avoiding WRMSR MSR_MISC_FEATURES_ENABLES whenever possible.

If host's value is zero, nothing needs to be done, since guest can use
kvm emulated cpuid faulting.

If host's value is non-zero, it need not clear MSR_MISC_FEATURES_ENABLES
unconditionally. We can use hardware cpuid faulting if guest's
value is equal to host'value, thus avoid WRMSR
MSR_MISC_FEATURES_ENABLES.

Since hardware cpuid faulting takes higher priority than CPUID vm exit,
it should be updated to hardware while guest wrmsr and hardware cpuid
faulting is used for guest.

Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
---
 arch/x86/include/asm/kvm_host.h |  2 ++
 arch/x86/kvm/vmx/vmx.c          | 13 ++++++++++---
 arch/x86/kvm/x86.c              | 15 ++++++++++++---
 3 files changed, 24 insertions(+), 6 deletions(-)

diff --git a/arch/x86/include/asm/kvm_host.h b/arch/x86/include/asm/kvm_host.h
index 2c53df4a5a2a..9bcb444b903d 100644
--- a/arch/x86/include/asm/kvm_host.h
+++ b/arch/x86/include/asm/kvm_host.h
@@ -1343,6 +1343,8 @@ void kvm_lmsw(struct kvm_vcpu *vcpu, unsigned long msw);
 void kvm_get_cs_db_l_bits(struct kvm_vcpu *vcpu, int *db, int *l);
 int kvm_set_xcr(struct kvm_vcpu *vcpu, u32 index, u64 xcr);
 
+int kvm_supported_msr_misc_features_enables(struct kvm_vcpu *vcpu, u64 data);
+
 int kvm_get_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr);
 int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr);
 
diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
index 65aa947947ba..73bb11f74b36 100644
--- a/arch/x86/kvm/vmx/vmx.c
+++ b/arch/x86/kvm/vmx/vmx.c
@@ -1035,10 +1035,10 @@ static void vmx_prepare_guest_misc_features_enables(struct vcpu_vmx *vmx)
 {
 	u64 msrval = this_cpu_read(msr_misc_features_shadow);
 
-	if (!msrval)
+	if (!msrval || msrval == vmx->vcpu.arch.msr_misc_features_enables)
 		return;
 
-	wrmsrl(MSR_MISC_FEATURES_ENABLES, 0ULL);
+	wrmsrl(MSR_MISC_FEATURES_ENABLES, vmx->vcpu.arch.msr_misc_features_enables);
 }
 
 void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
@@ -1136,7 +1136,7 @@ static void vmx_load_host_misc_features_enables(struct vcpu_vmx *vmx)
 {
 	u64 msrval = this_cpu_read(msr_misc_features_shadow);
 
-	if (!msrval)
+	if (!msrval || msrval == vmx->vcpu.arch.msr_misc_features_enables)
 		return;
 
 	wrmsrl(MSR_MISC_FEATURES_ENABLES, msrval);
@@ -2043,6 +2043,13 @@ static int vmx_set_msr(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
 		else
 			vmx->pt_desc.guest.addr_a[index / 2] = data;
 		break;
+	case MSR_MISC_FEATURES_ENABLES:
+		if (!kvm_supported_msr_misc_features_enables(vcpu, data))
+			return 1;
+		if (this_cpu_read(msr_misc_features_shadow) && vmx->loaded_cpu_state)
+			wrmsrl(MSR_MISC_FEATURES_ENABLES, data);
+		vcpu->arch.msr_misc_features_enables = data;
+		break;
 	case MSR_TSC_AUX:
 		if (!msr_info->host_initiated &&
 		    !guest_cpuid_has(vcpu, X86_FEATURE_RDTSCP))
diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index ad1df965574e..d2af90422a51 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -2449,6 +2449,17 @@ static void record_steal_time(struct kvm_vcpu *vcpu)
 		&vcpu->arch.st.steal, sizeof(struct kvm_steal_time));
 }
 
+int kvm_supported_msr_misc_features_enables(struct kvm_vcpu *vcpu, u64 data)
+{
+	if (data & ~MSR_MISC_FEATURES_ENABLES_CPUID_FAULT ||
+	    (data & MSR_MISC_FEATURES_ENABLES_CPUID_FAULT &&
+	     !supports_cpuid_fault(vcpu)))
+		return 0;
+	else
+		return 1;
+}
+EXPORT_SYMBOL_GPL(kvm_supported_msr_misc_features_enables);
+
 int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
 {
 	bool pr = false;
@@ -2669,9 +2680,7 @@ int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
 		vcpu->arch.msr_platform_info = data;
 		break;
 	case MSR_MISC_FEATURES_ENABLES:
-		if (data & ~MSR_MISC_FEATURES_ENABLES_CPUID_FAULT ||
-		    (data & MSR_MISC_FEATURES_ENABLES_CPUID_FAULT &&
-		     !supports_cpuid_fault(vcpu)))
+		if (!kvm_supported_msr_misc_features_enables(vcpu, data))
 			return 1;
 		vcpu->arch.msr_misc_features_enables = data;
 		break;
-- 
2.19.1

Re: [PATCH v3 1/2] kvm/vmx: Switch MSR_MISC_FEATURES_ENABLES between host and guest

[Sean Christopherson]

On Mon, Mar 25, 2019 at 04:06:49PM +0800, Xiaoyao Li wrote:
> There are two defined bits in MSR_MISC_FEATURES_ENABLES, bit 0 for cpuid
> faulting and bit 1 for ring3mwait.
> 
> == cpuid Faulting ==
> cpuid faulting is a feature about CPUID instruction. When cpuid faulting
> is enabled, all execution of the CPUID instruction outside system-management
> mode (SMM) cause a general-protection (#GP) if the CPL > 0.
> 
> About this feature, detailed information can be found at
> https://www.intel.com/content/dam/www/public/us/en/documents/application-notes/virtualization-technology-flexmigration-application-note.pdf
> 
> Current KVM provides software emulation of this feature for guest.
> However, because cpuid faulting takes higher priority over CPUID vm exit (Intel
> SDM vol3.25.1.1), there is a risk of leaking cpuid faulting to guest when host
> enables it. If host enables cpuid faulting by setting the bit 0 of
> MSR_MISC_FEATURES_ENABLES, it will pass to guest since there is no switch of
> MSR_MISC_FEATURES_ENABLES yet. As a result, when guest calls CPUID instruction
> in CPL > 0, it will generate a #GP instead of CPUID vm eixt.
> 
> This issue will cause guest boot failure when guest uses *modprobe*
> to load modules. *modprobe* calls CPUID instruction, thus causing #GP in
> guest. Since there is no handling of cpuid faulting in #GP handler, guest
> fails boot.
> 
> == ring3mwait ==
> Ring3mwait is a Xeon-Phi Product Family x200 series specific feature,
> which allows the MONITOR and MWAIT instructions to be executed in rings
> other than ring 0. The feature can be enabled by setting bit 1 in
> MSR_MISC_FEATURES_ENABLES. The register can also be read to determine
> whether the instructions are enabled at other than ring 0.
> 
> About this feature, description can be found at
> https://software.intel.com/en-us/blogs/2016/10/06/intel-xeon-phi-product-family-x200-knl-user-mode-ring-3-monitor-and-mwait
> 
> Current kvm doesn't expose feature ring3mwait to guest. However, there is also
> a risk of leaking ring3mwait to guest if host enables it since there is no
> switch of MSR_MISC_FEATURES_ENABLES.
> 
> == solution ==
> From above analysis, both cpuid faulting and ring3mwait can be leaked to guest.
> To fix this issue, MSR_MISC_FEATURES_ENABLES should be switched between host
> and guest. Since MSR_MISC_FEATURES_ENABLES is intel-specific, this patch
> implement the switching only in vmx.
> 
> For the reason that kvm provides the software emulation of cpuid faulting and
> kvm doesn't expose ring3mwait to guest. MSR_MISC_FEATURES_ENABLES can be just
> cleared to zero for guest when any of the features is enabled in host.
> 
> Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
> ---
>  arch/x86/kernel/process.c |  1 +
>  arch/x86/kvm/vmx/vmx.c    | 24 ++++++++++++++++++++++++
>  2 files changed, 25 insertions(+)
> 
> diff --git a/arch/x86/kernel/process.c b/arch/x86/kernel/process.c
> index 1bba1a3c0b01..94a566e79b6c 100644
> --- a/arch/x86/kernel/process.c
> +++ b/arch/x86/kernel/process.c
> @@ -191,6 +191,7 @@ int set_tsc_mode(unsigned int val)
>  }
>  
>  DEFINE_PER_CPU(u64, msr_misc_features_shadow);
> +EXPORT_PER_CPU_SYMBOL_GPL(msr_misc_features_shadow);
>  
>  static void set_cpuid_faulting(bool on)
>  {
> diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
> index 270c6566fd5a..65aa947947ba 100644
> --- a/arch/x86/kvm/vmx/vmx.c
> +++ b/arch/x86/kvm/vmx/vmx.c
> @@ -1031,6 +1031,16 @@ static void pt_guest_exit(struct vcpu_vmx *vmx)
>  	wrmsrl(MSR_IA32_RTIT_CTL, vmx->pt_desc.host.ctl);
>  }
>  
> +static void vmx_prepare_guest_misc_features_enables(struct vcpu_vmx *vmx)

No need for @vmx.  My preference would be to drop the helpers entirely,
e.g. it's two lines of code, three if you count the declaration of msrval.

> +{
> +	u64 msrval = this_cpu_read(msr_misc_features_shadow);
> +
> +	if (!msrval)
> +		return;
> +
> +	wrmsrl(MSR_MISC_FEATURES_ENABLES, 0ULL);
> +}
> +
>  void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
>  {
>  	struct vcpu_vmx *vmx = to_vmx(vcpu);
> @@ -1064,6 +1074,8 @@ void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
>  	vmx->loaded_cpu_state = vmx->loaded_vmcs;
>  	host_state = &vmx->loaded_cpu_state->host_state;
>  
> +	vmx_prepare_guest_misc_features_enables(vmx);
> +
>  	/*
>  	 * Set host fs and gs selectors.  Unfortunately, 22.2.3 does not
>  	 * allow segment selectors with cpl > 0 or ti == 1.
> @@ -1120,6 +1132,16 @@ void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
>  	}
>  }
>  
> +static void vmx_load_host_misc_features_enables(struct vcpu_vmx *vmx)

Likewise, no need for @vmx.

> +{
> +	u64 msrval = this_cpu_read(msr_misc_features_shadow);
> +
> +	if (!msrval)
> +		return;
> +
> +	wrmsrl(MSR_MISC_FEATURES_ENABLES, msrval);
> +}
> +
>  static void vmx_prepare_switch_to_host(struct vcpu_vmx *vmx)
>  {
>  	struct vmcs_host_state *host_state;
> @@ -1133,6 +1155,8 @@ static void vmx_prepare_switch_to_host(struct vcpu_vmx *vmx)
>  	++vmx->vcpu.stat.host_state_reload;
>  	vmx->loaded_cpu_state = NULL;
>  
> +	vmx_load_host_misc_features_enables(vmx);
> +
>  #ifdef CONFIG_X86_64
>  	rdmsrl(MSR_KERNEL_GS_BASE, vmx->msr_guest_kernel_gs_base);
>  #endif
> -- 
> 2.19.1
> 

Re: [PATCH v3 2/2] x86/vmx: optimize MSR_MISC_FEATURES_ENABLES switch

[Sean Christopherson]

On Mon, Mar 25, 2019 at 04:06:50PM +0800, Xiaoyao Li wrote:
> KVM needs to switch MSR_MISC_FEATURES_ENABLES between host and guest in
> every pcpu/vcpu context switch. Since WRMSR is expensive, this patch tries
> to save cycles by avoiding WRMSR MSR_MISC_FEATURES_ENABLES whenever possible.
> 
> If host's value is zero, nothing needs to be done, since guest can use
> kvm emulated cpuid faulting.
> 
> If host's value is non-zero, it need not clear MSR_MISC_FEATURES_ENABLES
> unconditionally. We can use hardware cpuid faulting if guest's
> value is equal to host'value, thus avoid WRMSR
> MSR_MISC_FEATURES_ENABLES.
> 
> Since hardware cpuid faulting takes higher priority than CPUID vm exit,
> it should be updated to hardware while guest wrmsr and hardware cpuid
> faulting is used for guest.
> 
> Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
> ---
>  arch/x86/include/asm/kvm_host.h |  2 ++
>  arch/x86/kvm/vmx/vmx.c          | 13 ++++++++++---
>  arch/x86/kvm/x86.c              | 15 ++++++++++++---
>  3 files changed, 24 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/x86/include/asm/kvm_host.h b/arch/x86/include/asm/kvm_host.h
> index 2c53df4a5a2a..9bcb444b903d 100644
> --- a/arch/x86/include/asm/kvm_host.h
> +++ b/arch/x86/include/asm/kvm_host.h
> @@ -1343,6 +1343,8 @@ void kvm_lmsw(struct kvm_vcpu *vcpu, unsigned long msw);
>  void kvm_get_cs_db_l_bits(struct kvm_vcpu *vcpu, int *db, int *l);
>  int kvm_set_xcr(struct kvm_vcpu *vcpu, u32 index, u64 xcr);
>  
> +int kvm_supported_msr_misc_features_enables(struct kvm_vcpu *vcpu, u64 data);
> +
>  int kvm_get_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr);
>  int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr);
>  
> diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
> index 65aa947947ba..73bb11f74b36 100644
> --- a/arch/x86/kvm/vmx/vmx.c
> +++ b/arch/x86/kvm/vmx/vmx.c
> @@ -1035,10 +1035,10 @@ static void vmx_prepare_guest_misc_features_enables(struct vcpu_vmx *vmx)
>  {
>  	u64 msrval = this_cpu_read(msr_misc_features_shadow);
>  
> -	if (!msrval)
> +	if (!msrval || msrval == vmx->vcpu.arch.msr_misc_features_enables)
>  		return;
>  
> -	wrmsrl(MSR_MISC_FEATURES_ENABLES, 0ULL);
> +	wrmsrl(MSR_MISC_FEATURES_ENABLES, vmx->vcpu.arch.msr_misc_features_enables);
>  }
>  
>  void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
> @@ -1136,7 +1136,7 @@ static void vmx_load_host_misc_features_enables(struct vcpu_vmx *vmx)
>  {
>  	u64 msrval = this_cpu_read(msr_misc_features_shadow);
>  
> -	if (!msrval)
> +	if (!msrval || msrval == vmx->vcpu.arch.msr_misc_features_enables)
>  		return;
>  
>  	wrmsrl(MSR_MISC_FEATURES_ENABLES, msrval);
> @@ -2043,6 +2043,13 @@ static int vmx_set_msr(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
>  		else
>  			vmx->pt_desc.guest.addr_a[index / 2] = data;
>  		break;
> +	case MSR_MISC_FEATURES_ENABLES:
> +		if (!kvm_supported_msr_misc_features_enables(vcpu, data))
> +			return 1;
> +		if (this_cpu_read(msr_misc_features_shadow) && vmx->loaded_cpu_state)
> +			wrmsrl(MSR_MISC_FEATURES_ENABLES, data);
> +		vcpu->arch.msr_misc_features_enables = data;
> +		break;
>  	case MSR_TSC_AUX:
>  		if (!msr_info->host_initiated &&
>  		    !guest_cpuid_has(vcpu, X86_FEATURE_RDTSCP))
> diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
> index ad1df965574e..d2af90422a51 100644
> --- a/arch/x86/kvm/x86.c
> +++ b/arch/x86/kvm/x86.c
> @@ -2449,6 +2449,17 @@ static void record_steal_time(struct kvm_vcpu *vcpu)
>  		&vcpu->arch.st.steal, sizeof(struct kvm_steal_time));
>  }
>  
> +int kvm_supported_msr_misc_features_enables(struct kvm_vcpu *vcpu, u64 data)

The name kvm_supported_msr_misc_features_enables() is a bit confusing,
e.g. I expected it to return a bitmask of the supported features.  Maybe
kvm_misc_features_enables_msr_valid() to be consistent with
vmx_feature_control_msr_valid()?

> +{
> +	if (data & ~MSR_MISC_FEATURES_ENABLES_CPUID_FAULT ||
> +	    (data & MSR_MISC_FEATURES_ENABLES_CPUID_FAULT &&
> +	     !supports_cpuid_fault(vcpu)))
> +		return 0;
> +	else
> +		return 1;

No need for the if-else, you can simply do:

	return (data & ~MSR_MISC_FEATURES_ENABLES_CPUID_FAULT) ||
	       (data & MSR_MISC_FEATURES_ENABLES_CPUID_FAULT &&
		!supports_cpuid_fault(vcpu));

You could even shorten it to:

        return (data & ~MSR_MISC_FEATURES_ENABLES_CPUID_FAULT) ||
               (data && !supports_cpuid_fault(vcpu));

although that might be getting a bit too cute.

> +}
> +EXPORT_SYMBOL_GPL(kvm_supported_msr_misc_features_enables);
> +
>  int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
>  {
>  	bool pr = false;
> @@ -2669,9 +2680,7 @@ int kvm_set_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
>  		vcpu->arch.msr_platform_info = data;
>  		break;
>  	case MSR_MISC_FEATURES_ENABLES:
> -		if (data & ~MSR_MISC_FEATURES_ENABLES_CPUID_FAULT ||
> -		    (data & MSR_MISC_FEATURES_ENABLES_CPUID_FAULT &&
> -		     !supports_cpuid_fault(vcpu)))
> +		if (!kvm_supported_msr_misc_features_enables(vcpu, data))
>  			return 1;
>  		vcpu->arch.msr_misc_features_enables = data;
>  		break;
> -- 
> 2.19.1
> 

Re: [PATCH v3 1/2] kvm/vmx: Switch MSR_MISC_FEATURES_ENABLES between host and guest

[Xiaoyao Li]

On Mon, 2019-03-25 at 08:33 -0700, Sean Christopherson wrote:
> On Mon, Mar 25, 2019 at 04:06:49PM +0800, Xiaoyao Li wrote:
> > There are two defined bits in MSR_MISC_FEATURES_ENABLES, bit 0 for cpuid
> > faulting and bit 1 for ring3mwait.
> > 
> > == cpuid Faulting ==
> > cpuid faulting is a feature about CPUID instruction. When cpuid faulting
> > is enabled, all execution of the CPUID instruction outside system-management
> > mode (SMM) cause a general-protection (#GP) if the CPL > 0.
> > 
> > About this feature, detailed information can be found at
> > 
https://www.intel.com/content/dam/www/public/us/en/documents/application-notes/virtualization-technology-flexmigration-application-note.pdf
> > 
> > Current KVM provides software emulation of this feature for guest.
> > However, because cpuid faulting takes higher priority over CPUID vm exit
> > (Intel
> > SDM vol3.25.1.1), there is a risk of leaking cpuid faulting to guest when
> > host
> > enables it. If host enables cpuid faulting by setting the bit 0 of
> > MSR_MISC_FEATURES_ENABLES, it will pass to guest since there is no switch of
> > MSR_MISC_FEATURES_ENABLES yet. As a result, when guest calls CPUID
> > instruction
> > in CPL > 0, it will generate a #GP instead of CPUID vm eixt.
> > 
> > This issue will cause guest boot failure when guest uses *modprobe*
> > to load modules. *modprobe* calls CPUID instruction, thus causing #GP in
> > guest. Since there is no handling of cpuid faulting in #GP handler, guest
> > fails boot.
> > 
> > == ring3mwait ==
> > Ring3mwait is a Xeon-Phi Product Family x200 series specific feature,
> > which allows the MONITOR and MWAIT instructions to be executed in rings
> > other than ring 0. The feature can be enabled by setting bit 1 in
> > MSR_MISC_FEATURES_ENABLES. The register can also be read to determine
> > whether the instructions are enabled at other than ring 0.
> > 
> > About this feature, description can be found at
> > 
https://software.intel.com/en-us/blogs/2016/10/06/intel-xeon-phi-product-family-x200-knl-user-mode-ring-3-monitor-and-mwait
> > 
> > Current kvm doesn't expose feature ring3mwait to guest. However, there is
> > also
> > a risk of leaking ring3mwait to guest if host enables it since there is no
> > switch of MSR_MISC_FEATURES_ENABLES.
> > 
> > == solution ==
> > From above analysis, both cpuid faulting and ring3mwait can be leaked to
> > guest.
> > To fix this issue, MSR_MISC_FEATURES_ENABLES should be switched between host
> > and guest. Since MSR_MISC_FEATURES_ENABLES is intel-specific, this patch
> > implement the switching only in vmx.
> > 
> > For the reason that kvm provides the software emulation of cpuid faulting
> > and
> > kvm doesn't expose ring3mwait to guest. MSR_MISC_FEATURES_ENABLES can be
> > just
> > cleared to zero for guest when any of the features is enabled in host.
> > 
> > Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
> > ---
> >  arch/x86/kernel/process.c |  1 +
> >  arch/x86/kvm/vmx/vmx.c    | 24 ++++++++++++++++++++++++
> >  2 files changed, 25 insertions(+)
> > 
> > diff --git a/arch/x86/kernel/process.c b/arch/x86/kernel/process.c
> > index 1bba1a3c0b01..94a566e79b6c 100644
> > --- a/arch/x86/kernel/process.c
> > +++ b/arch/x86/kernel/process.c
> > @@ -191,6 +191,7 @@ int set_tsc_mode(unsigned int val)
> >  }
> >  
> >  DEFINE_PER_CPU(u64, msr_misc_features_shadow);
> > +EXPORT_PER_CPU_SYMBOL_GPL(msr_misc_features_shadow);
> >  
> >  static void set_cpuid_faulting(bool on)
> >  {
> > diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
> > index 270c6566fd5a..65aa947947ba 100644
> > --- a/arch/x86/kvm/vmx/vmx.c
> > +++ b/arch/x86/kvm/vmx/vmx.c
> > @@ -1031,6 +1031,16 @@ static void pt_guest_exit(struct vcpu_vmx *vmx)
> >  	wrmsrl(MSR_IA32_RTIT_CTL, vmx->pt_desc.host.ctl);
> >  }
> >  
> > +static void vmx_prepare_guest_misc_features_enables(struct vcpu_vmx *vmx)
> 
> No need for @vmx.  My preference would be to drop the helpers entirely,
> e.g. it's two lines of code, three if you count the declaration of msrval.

My mistake, @vmx should be removed and add in the next patch.

Well, my initial thought of using the helper is because the handling of
MSR_MISC_FEATURES_ENABLES might not be so simple if add the handling of
ring3wait bit. Although in this patch, it just clears the bit 1
of MSR_MISC_FEATURES_ENABLES since kvm doesn't expose ring3mwait to guest yet
and kvm doesn't allow guest to set ring3mwait bit, there indeed is an issue that
guest kernel will generate "unchecked MSR access error: WRMSR to 0x140" when we
use `-cpu host` in a Xeon Phi 200 series host. Since feature ring3mwait is
enumerated by FMS in current kernel code, using '-cpu host' makes guest kernel
think it has feature ring3wait too. However there is support of ring3mwait yet,
guest kernel will generate "unchecked MSR access error: WRMSR to 0x140" when it
setup ring3mwait.

Unfortunately, I didn't provide the emualtion and handling of ring3mwait in this
patchset, but keep the helper. You're right, it is really unnecessary in this
patchset. I will remove the helper in the next version. 

> > +{
> > +	u64 msrval = this_cpu_read(msr_misc_features_shadow);
> > +
> > +	if (!msrval)
> > +		return;
> > +
> > +	wrmsrl(MSR_MISC_FEATURES_ENABLES, 0ULL);
> > +}
> > +
> >  void vmx_prepare_switch_to_guest(struct kvm_vcpu *vcpu)
> >  {
> >  	struct vcpu_vmx *vmx = to_vmx(vcpu);
> > @@ -1064,6 +1074,8 @@ void vmx_prepare_switch_to_guest(struct kvm_vcpu
> > *vcpu)
> >  	vmx->loaded_cpu_state = vmx->loaded_vmcs;
> >  	host_state = &vmx->loaded_cpu_state->host_state;
> >  
> > +	vmx_prepare_guest_misc_features_enables(vmx);
> > +
> >  	/*
> >  	 * Set host fs and gs selectors.  Unfortunately, 22.2.3 does not
> >  	 * allow segment selectors with cpl > 0 or ti == 1.
> > @@ -1120,6 +1132,16 @@ void vmx_prepare_switch_to_guest(struct kvm_vcpu
> > *vcpu)
> >  	}
> >  }
> >  
> > +static void vmx_load_host_misc_features_enables(struct vcpu_vmx *vmx)
> 
> Likewise, no need for @vmx.
> 
> > +{
> > +	u64 msrval = this_cpu_read(msr_misc_features_shadow);
> > +
> > +	if (!msrval)
> > +		return;
> > +
> > +	wrmsrl(MSR_MISC_FEATURES_ENABLES, msrval);
> > +}
> > +
> >  static void vmx_prepare_switch_to_host(struct vcpu_vmx *vmx)
> >  {
> >  	struct vmcs_host_state *host_state;
> > @@ -1133,6 +1155,8 @@ static void vmx_prepare_switch_to_host(struct vcpu_vmx
> > *vmx)
> >  	++vmx->vcpu.stat.host_state_reload;
> >  	vmx->loaded_cpu_state = NULL;
> >  
> > +	vmx_load_host_misc_features_enables(vmx);
> > +
> >  #ifdef CONFIG_X86_64
> >  	rdmsrl(MSR_KERNEL_GS_BASE, vmx->msr_guest_kernel_gs_base);
> >  #endif
> > -- 
> > 2.19.1
> >