Linux-ACPI Archive on lore.kernel.org
 help / color / Atom feed
From: Hans de Goede <hdegoede@redhat.com>
To: "Thierry Reding" <thierry.reding@gmail.com>,
	"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
	"Jani Nikula" <jani.nikula@linux.intel.com>,
	"Joonas Lahtinen" <joonas.lahtinen@linux.intel.com>,
	"Rodrigo Vivi" <rodrigo.vivi@intel.com>,
	"Ville Syrjälä" <ville.syrjala@linux.intel.com>,
	"Rafael J . Wysocki" <rjw@rjwysocki.net>,
	"Len Brown" <lenb@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>,
	linux-pwm@vger.kernel.org,
	intel-gfx <intel-gfx@lists.freedesktop.org>,
	dri-devel@lists.freedesktop.org,
	Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
	Mika Westerberg <mika.westerberg@linux.intel.com>,
	linux-acpi@vger.kernel.org,
	"Rafael J . Wysocki" <rafael.j.wysocki@intel.com>
Subject: [PATCH v5 02/16] ACPI / LPSS: Save Cherry Trail PWM ctx registers only once (at activation)
Date: Fri, 17 Jul 2020 15:37:39 +0200
Message-ID: <20200717133753.127282-3-hdegoede@redhat.com> (raw)
In-Reply-To: <20200717133753.127282-1-hdegoede@redhat.com>

The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets turned off from the _PS3 method of the graphics-card dev:

            Method (_PS3, 0, Serialized)  // _PS3: Power State 3
            {
                ...
                            PWMB = PWMC /* \_SB_.PCI0.GFX0.PWMC */
                            PSAT |= 0x03
                            Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
                ...
            }

Where PSAT is the power-status register of the PWM controller.

Since the i915 driver will do a pwm_get on the pwm device as it uses it to
control the LCD panel backlight, there is a device-link marking the i915
device as a consumer of the pwm device. So that the PWM controller will
always be suspended after the i915 driver suspends (which is the right
thing to do). This causes the above GFX0 PS3 AML code to run before
acpi_lpss.c calls acpi_lpss_save_ctx().

So on these devices the PWM controller will already be off when
acpi_lpss_save_ctx() runs. This causes it to read/save all 1-s (0xffffffff)
as ctx register values.

When these bogus values get restored on resume the PWM controller actually
keeps working, since most bits are reserved, but this does set bit 3 of
the LPSS General purpose register, which for the PWM controller has the
following function: "This bit is re-used to support 32kHz slow mode.
Default is 19.2MHz as PWM source clock".

This causes the clock of the PWM controller to switch from 19.2MHz to
32KHz, which is a slow-down of a factor 600. Surprisingly enough so far
there have been few bug reports about this. This is likely because the
i915 driver was hardcoding the PWM frequency to 46 KHz, which divided
by 600 would result in a PWM frequency of approx. 78 Hz, which mostly
still works fine. There are some bug reports about the LCD backlight
flickering after suspend/resume which are likely caused by this issue.

But with the upcoming patch-series to finally switch the i915 drivers
code for external PWM controllers to use the atomic API and to honor
the PWM frequency specified in the video BIOS (VBT), this becomes a much
bigger problem. On most cases the VBT specifies either 200 Hz or 20
KHz as PWM frequency, which with the mentioned issue ends up being either
1/3 Hz, where the backlight actually visible blinks on and off every 3s,
or in 33 Hz and horrible flickering of the backlight.

There are a number of possible solutions to this problem:

1. Make acpi_lpss_save_ctx() run before GFX0._PS3
 Pro: Clean solution from pov of not medling with save/restore ctx code
 Con: As mentioned the current ordering is the right thing to do
 Con: Requires assymmetry in at what suspend/resume phase we do the save vs
      restore, requiring more suspend/resume ordering hacks in already
      convoluted acpi_lpss.c suspend/resume code.
2. Do some sort of save once mode for the LPSS ctx
 Pro: Reasonably clean
 Con: Needs a new LPSS flag + code changes to handle the flag
3. Detect we have failed to save the ctx registers and do not restore them
 Pro: Not PWM specific, might help with issues on other LPSS devices too
 Con: If we can get away with not restoring the ctx why bother with it at
      all?
4. Do not save the ctx for CHT PWM controllers
 Pro: Clean, as simple as dropping a flag?
 Con: Not so simple as dropping a flag, needs a new flag to ensure that
      we still do lpss_deassert_reset() on device activation.
5. Make the pwm-lpss code fixup the LPSS-context registers
 Pro: Keeps acpi_lpss.c code clean
 Con: Moves knowledge of LPSS-context into the pwm-lpss.c code

1 and 5 both do not seem to be a desirable way forward.

3 and 4 seem ok, but they both assume that restoring the LPSS-context
registers is not necessary. I have done a couple of test and those do
show that restoring the LPSS-context indeed does not seem to be necessary
on devices using s2idle suspend (and successfully reaching S0i3). But I
have no hardware to test deep / S3 suspend. So I'm not sure that not
restoring the context is safe.

That leaves solution 2, which is about as simple / clean as 3 and 4,
so this commit fixes the described problem by implementing a new
LPSS_SAVE_CTX_ONCE flag and setting that for the CHT PWM controllers.

Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
- Move #define LPSS_SAVE_CTX_ONCE define to group it with LPSS_SAVE_CTX
---
 drivers/acpi/acpi_lpss.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

diff --git a/drivers/acpi/acpi_lpss.c b/drivers/acpi/acpi_lpss.c
index 67892fc0b822..a8d7d83ac761 100644
--- a/drivers/acpi/acpi_lpss.c
+++ b/drivers/acpi/acpi_lpss.c
@@ -67,7 +67,15 @@ ACPI_MODULE_NAME("acpi_lpss");
 #define LPSS_CLK_DIVIDER		BIT(2)
 #define LPSS_LTR			BIT(3)
 #define LPSS_SAVE_CTX			BIT(4)
-#define LPSS_NO_D3_DELAY		BIT(5)
+/*
+ * For some devices the DSDT AML code for another device turns off the device
+ * before our suspend handler runs, causing us to read/save all 1-s (0xffffffff)
+ * as ctx register values.
+ * Luckily these devices always use the same ctx register values, so we can
+ * work around this by saving the ctx registers once on activation.
+ */
+#define LPSS_SAVE_CTX_ONCE		BIT(5)
+#define LPSS_NO_D3_DELAY		BIT(6)
 
 struct lpss_private_data;
 
@@ -254,7 +262,7 @@ static const struct lpss_device_desc byt_pwm_dev_desc = {
 };
 
 static const struct lpss_device_desc bsw_pwm_dev_desc = {
-	.flags = LPSS_SAVE_CTX | LPSS_NO_D3_DELAY,
+	.flags = LPSS_SAVE_CTX_ONCE | LPSS_NO_D3_DELAY,
 	.prv_offset = 0x800,
 	.setup = bsw_pwm_setup,
 	.resume_from_noirq = true,
@@ -885,9 +893,14 @@ static int acpi_lpss_activate(struct device *dev)
 	 * we have to deassert reset line to be sure that ->probe() will
 	 * recognize the device.
 	 */
-	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+	if (pdata->dev_desc->flags & (LPSS_SAVE_CTX | LPSS_SAVE_CTX_ONCE))
 		lpss_deassert_reset(pdata);
 
+#ifdef CONFIG_PM
+	if (pdata->dev_desc->flags & LPSS_SAVE_CTX_ONCE)
+		acpi_lpss_save_ctx(dev, pdata);
+#endif
+
 	return 0;
 }
 
@@ -1031,7 +1044,7 @@ static int acpi_lpss_resume(struct device *dev)
 
 	acpi_lpss_d3_to_d0_delay(pdata);
 
-	if (pdata->dev_desc->flags & LPSS_SAVE_CTX)
+	if (pdata->dev_desc->flags & (LPSS_SAVE_CTX | LPSS_SAVE_CTX_ONCE))
 		acpi_lpss_restore_ctx(dev, pdata);
 
 	return 0;
-- 
2.26.2


  parent reply index

Thread overview: 40+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-17 13:37 [PATCH v5 00/16] acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API Hans de Goede
2020-07-17 13:37 ` [PATCH v5 01/16] ACPI / LPSS: Resume Cherry Trail PWM controller in no-irq phase Hans de Goede
2020-07-17 13:37 ` Hans de Goede [this message]
2020-07-17 13:37 ` [PATCH v5 03/16] pwm: lpss: Fix off by one error in base_unit math in pwm_lpss_prepare() Hans de Goede
2020-07-17 13:37 ` [PATCH v5 04/16] pwm: lpss: Add range limit check for the base_unit register value Hans de Goede
2020-07-17 13:37 ` [PATCH v5 05/16] pwm: lpss: Add pwm_lpss_prepare_enable() helper Hans de Goede
2020-07-28 18:45   ` Andy Shevchenko
2020-07-28 19:49     ` Hans de Goede
2020-07-17 13:37 ` [PATCH v5 06/16] pwm: lpss: Use pwm_lpss_apply() when restoring state on resume Hans de Goede
2020-07-28 18:57   ` Andy Shevchenko
2020-07-28 19:55     ` Hans de Goede
2020-07-29  8:12       ` Andy Shevchenko
2020-08-02 20:51         ` Hans de Goede
2020-08-03  8:41           ` Andy Shevchenko
2020-07-17 13:37 ` [PATCH v5 07/16] pwm: crc: Fix period / duty_cycle times being off by a factor of 256 Hans de Goede
2020-07-28 19:36   ` Andy Shevchenko
2020-07-28 20:00     ` Hans de Goede
2020-07-29  8:13   ` Andy Shevchenko
2020-07-17 13:37 ` [PATCH v5 08/16] pwm: crc: Fix off-by-one error in the clock-divider calculations Hans de Goede
2020-07-29 10:28   ` Andy Shevchenko
2020-07-17 13:37 ` [PATCH v5 09/16] pwm: crc: Fix period changes not having any effect Hans de Goede
2020-07-29 10:30   ` Andy Shevchenko
2020-07-17 13:37 ` [PATCH v5 10/16] pwm: crc: Enable/disable PWM output on enable/disable Hans de Goede
2020-07-29 10:32   ` Andy Shevchenko
2020-07-17 13:37 ` [PATCH v5 11/16] pwm: crc: Implement apply() method to support the new atomic PWM API Hans de Goede
2020-07-29 10:51   ` Andy Shevchenko
2020-07-17 13:37 ` [PATCH v5 12/16] pwm: crc: Implement get_state() method Hans de Goede
2020-07-17 13:37 ` [PATCH v5 13/16] drm/i915: panel: Add get_vbt_pwm_freq() helper Hans de Goede
2020-07-17 13:37 ` [PATCH v5 14/16] drm/i915: panel: Honor the VBT PWM frequency for devs with an external PWM controller Hans de Goede
2020-07-17 13:44 ` [PATCH v5 15/16] drm/i915: panel: Honor the VBT PWM min setting " Hans de Goede
2020-07-17 13:44   ` [PATCH v5 16/16] drm/i915: panel: Use atomic PWM API " Hans de Goede
2020-07-27  7:41 ` [PATCH v5 00/16] acpi/pwm/i915: Convert pwm-crc and i915 driver's PWM code to use the atomic PWM API Thierry Reding
2020-07-29  8:23   ` Andy Shevchenko
2020-07-29  9:32     ` Hans de Goede
2020-07-30  9:26       ` Thierry Reding
2020-08-01 14:33         ` Hans de Goede
2020-07-29 10:54 ` Andy Shevchenko
2020-08-01 14:38   ` Hans de Goede
2020-08-02 11:25     ` Andy Shevchenko
2020-08-02 19:43       ` Hans de Goede

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200717133753.127282-3-hdegoede@redhat.com \
    --to=hdegoede@redhat.com \
    --cc=andriy.shevchenko@linux.intel.com \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=intel-gfx@lists.freedesktop.org \
    --cc=jani.nikula@linux.intel.com \
    --cc=joonas.lahtinen@linux.intel.com \
    --cc=lenb@kernel.org \
    --cc=linux-acpi@vger.kernel.org \
    --cc=linux-pwm@vger.kernel.org \
    --cc=mika.westerberg@linux.intel.com \
    --cc=rafael.j.wysocki@intel.com \
    --cc=rjw@rjwysocki.net \
    --cc=rodrigo.vivi@intel.com \
    --cc=thierry.reding@gmail.com \
    --cc=u.kleine-koenig@pengutronix.de \
    --cc=ville.syrjala@linux.intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ACPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-acpi/0 linux-acpi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-acpi linux-acpi/ https://lore.kernel.org/linux-acpi \
		linux-acpi@vger.kernel.org
	public-inbox-index linux-acpi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-acpi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git