Linux-ACPI Archive on lore.kernel.org
 help / color / Atom feed
From: Ben Widawsky <ben.widawsky@intel.com>
To: linux-cxl@vger.kernel.org
Cc: Ben Widawsky <ben.widawsky@intel.com>,
	linux-pci@vger.kernel.org, linux-acpi@vger.kernel.org,
	ira.weiny@intel.com, vishal.l.verma@intel.com,
	alison.schofield@intel.com, dan.j.williams@intel.com,
	linux-kernel@vger.kernel.org
Subject: [PATCH 3/7] cxl/mem: Move register locator logic into reg setup
Date: Wed,  7 Apr 2021 15:26:21 -0700
Message-ID: <20210407222625.320177-4-ben.widawsky@intel.com> (raw)
In-Reply-To: <20210407222625.320177-1-ben.widawsky@intel.com>

Start moving code around to ultimately get rid of @cxlm.base. The
@cxlm.base member serves no purpose other than intermediate storage of
the offset found in cxl_mem_map_regblock() later used by
cxl_mem_setup_regs(). Aside from wanting to get rid of this useless
member, it will help later when adding new register block identifiers.

While @cxlm.base still exists, it will become trivial to remove it in a
future patch.

No functional change is meant to be introduced in this patch.

Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
---
 drivers/cxl/mem.c | 135 +++++++++++++++++++++++-----------------------
 1 file changed, 68 insertions(+), 67 deletions(-)

diff --git a/drivers/cxl/mem.c b/drivers/cxl/mem.c
index 520edaf233d4..04b4f7445083 100644
--- a/drivers/cxl/mem.c
+++ b/drivers/cxl/mem.c
@@ -870,34 +870,6 @@ static int cxl_mem_mbox_send_cmd(struct cxl_mem *cxlm, u16 opcode,
 	return 0;
 }
 
-/**
- * cxl_mem_setup_regs() - Setup necessary MMIO.
- * @cxlm: The CXL memory device to communicate with.
- *
- * Return: 0 if all necessary registers mapped.
- *
- * A memory device is required by spec to implement a certain set of MMIO
- * regions. The purpose of this function is to enumerate and map those
- * registers.
- */
-static int cxl_mem_setup_regs(struct cxl_mem *cxlm)
-{
-	struct device *dev = &cxlm->pdev->dev;
-	struct cxl_regs *regs = &cxlm->regs;
-
-	cxl_setup_device_regs(dev, cxlm->base, &regs->device_regs);
-
-	if (!regs->status || !regs->mbox || !regs->memdev) {
-		dev_err(dev, "registers not found: %s%s%s\n",
-			!regs->status ? "status " : "",
-			!regs->mbox ? "mbox " : "",
-			!regs->memdev ? "memdev" : "");
-		return -ENXIO;
-	}
-
-	return 0;
-}
-
 static int cxl_mem_setup_mailbox(struct cxl_mem *cxlm)
 {
 	const int cap = readl(cxlm->regs.mbox + CXLDEV_MBOX_CAPS_OFFSET);
@@ -1005,6 +977,73 @@ static int cxl_mem_dvsec(struct pci_dev *pdev, int dvsec)
 	return 0;
 }
 
+/**
+ * cxl_mem_setup_regs() - Setup necessary MMIO.
+ * @cxlm: The CXL memory device to communicate with.
+ *
+ * Return: 0 if all necessary registers mapped.
+ *
+ * A memory device is required by spec to implement a certain set of MMIO
+ * regions. The purpose of this function is to enumerate and map those
+ * registers.
+ */
+static int cxl_mem_setup_regs(struct cxl_mem *cxlm)
+{
+	struct cxl_regs *regs = &cxlm->regs;
+	struct pci_dev *pdev = cxlm->pdev;
+	struct device *dev = &pdev->dev;
+	u32 regloc_size, regblocks;
+	int rc, regloc, i;
+
+	regloc = cxl_mem_dvsec(pdev, PCI_DVSEC_ID_CXL_REGLOC_OFFSET);
+	if (!regloc) {
+		dev_err(dev, "register location dvsec not found\n");
+		return -ENXIO;
+	}
+
+	/* Get the size of the Register Locator DVSEC */
+	pci_read_config_dword(pdev, regloc + PCI_DVSEC_HEADER1, &regloc_size);
+	regloc_size = FIELD_GET(PCI_DVSEC_HEADER1_LENGTH_MASK, regloc_size);
+
+	regloc += PCI_DVSEC_ID_CXL_REGLOC_BLOCK1_OFFSET;
+	regblocks = (regloc_size - PCI_DVSEC_ID_CXL_REGLOC_BLOCK1_OFFSET) / 8;
+
+	for (i = 0; i < regblocks; i++, regloc += 8) {
+		u32 reg_lo, reg_hi;
+		u8 reg_type;
+
+		/* "register low and high" contain other bits */
+		pci_read_config_dword(pdev, regloc, &reg_lo);
+		pci_read_config_dword(pdev, regloc + 4, &reg_hi);
+
+		reg_type = FIELD_GET(CXL_REGLOC_RBI_MASK, reg_lo);
+
+		if (reg_type == CXL_REGLOC_RBI_MEMDEV) {
+			rc = cxl_mem_map_regblock(cxlm, reg_lo, reg_hi);
+			if (rc)
+				return rc;
+			break;
+		}
+	}
+
+	if (i == regblocks) {
+		dev_err(dev, "Missing register locator for device registers\n");
+		return -ENXIO;
+	}
+
+	cxl_setup_device_regs(dev, cxlm->base, &regs->device_regs);
+
+	if (!regs->status || !regs->mbox || !regs->memdev) {
+		dev_err(dev, "registers not found: %s%s%s\n",
+			!regs->status ? "status " : "",
+			!regs->mbox ? "mbox " : "",
+			!regs->memdev ? "memdev" : "");
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
 static struct cxl_memdev *to_cxl_memdev(struct device *dev)
 {
 	return container_of(dev, struct cxl_memdev, dev);
@@ -1410,10 +1449,8 @@ static int cxl_mem_identify(struct cxl_mem *cxlm)
 
 static int cxl_mem_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
-	struct device *dev = &pdev->dev;
-	u32 regloc_size, regblocks;
 	struct cxl_mem *cxlm;
-	int rc, regloc, i;
+	int rc;
 
 	rc = pcim_enable_device(pdev);
 	if (rc)
@@ -1423,42 +1460,6 @@ static int cxl_mem_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	if (IS_ERR(cxlm))
 		return PTR_ERR(cxlm);
 
-	regloc = cxl_mem_dvsec(pdev, PCI_DVSEC_ID_CXL_REGLOC_OFFSET);
-	if (!regloc) {
-		dev_err(dev, "register location dvsec not found\n");
-		return -ENXIO;
-	}
-
-	/* Get the size of the Register Locator DVSEC */
-	pci_read_config_dword(pdev, regloc + PCI_DVSEC_HEADER1, &regloc_size);
-	regloc_size = FIELD_GET(PCI_DVSEC_HEADER1_LENGTH_MASK, regloc_size);
-
-	regloc += PCI_DVSEC_ID_CXL_REGLOC_BLOCK1_OFFSET;
-	regblocks = (regloc_size - PCI_DVSEC_ID_CXL_REGLOC_BLOCK1_OFFSET) / 8;
-
-	for (i = 0; i < regblocks; i++, regloc += 8) {
-		u32 reg_lo, reg_hi;
-		u8 reg_type;
-
-		/* "register low and high" contain other bits */
-		pci_read_config_dword(pdev, regloc, &reg_lo);
-		pci_read_config_dword(pdev, regloc + 4, &reg_hi);
-
-		reg_type = FIELD_GET(CXL_REGLOC_RBI_MASK, reg_lo);
-
-		if (reg_type == CXL_REGLOC_RBI_MEMDEV) {
-			rc = cxl_mem_map_regblock(cxlm, reg_lo, reg_hi);
-			if (rc)
-				return rc;
-			break;
-		}
-	}
-
-	if (i == regblocks) {
-		dev_err(dev, "Missing register locator for device registers\n");
-		return -ENXIO;
-	}
-
 	rc = cxl_mem_setup_regs(cxlm);
 	if (rc)
 		return rc;
-- 
2.31.1


  parent reply index

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-04-07 22:26 [PATCH 0/7] Enumerate HDM Decoder registers Ben Widawsky
2021-04-07 22:26 ` [PATCH 1/7] cxl/mem: Use dev instead of pdev->dev Ben Widawsky
2021-04-08 17:08   ` Jonathan Cameron
2021-04-07 22:26 ` [PATCH 2/7] cxl/mem: Split creation from mapping in probe Ben Widawsky
2021-04-08 17:13   ` Jonathan Cameron
2021-04-07 22:26 ` Ben Widawsky [this message]
2021-04-08 17:27   ` [PATCH 3/7] cxl/mem: Move register locator logic into reg setup Jonathan Cameron
2021-04-07 22:26 ` [PATCH 4/7] cxl/mem: Get rid of @cxlm.base Ben Widawsky
2021-04-08 17:26   ` Jonathan Cameron
2021-04-13 16:17     ` Ben Widawsky
2021-04-14  9:24       ` Jonathan Cameron
2021-05-20 21:29       ` [PATCH v2 " Ben Widawsky
2021-04-07 22:26 ` [PATCH 5/7] cxl/mem: Move device register setup Ben Widawsky
2021-04-08 17:28   ` Jonathan Cameron
2021-04-07 22:26 ` [PATCH 6/7] cxl/mem: Create a helper to setup device regs Ben Widawsky
2021-04-08 17:33   ` Jonathan Cameron
2021-04-15 22:54   ` Dan Williams
2021-04-07 22:26 ` [PATCH 7/7] cxl: Add HDM decoder capbilities Ben Widawsky
2021-04-08 17:57   ` Jonathan Cameron
2021-04-15 23:27   ` Dan Williams
2021-04-15 23:50     ` Ben Widawsky
2021-04-16  0:25       ` Dan Williams

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210407222625.320177-4-ben.widawsky@intel.com \
    --to=ben.widawsky@intel.com \
    --cc=alison.schofield@intel.com \
    --cc=dan.j.williams@intel.com \
    --cc=ira.weiny@intel.com \
    --cc=linux-acpi@vger.kernel.org \
    --cc=linux-cxl@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=vishal.l.verma@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-ACPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-acpi/0 linux-acpi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-acpi linux-acpi/ https://lore.kernel.org/linux-acpi \
		linux-acpi@vger.kernel.org
	public-inbox-index linux-acpi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-acpi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git