* [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider
2019-01-08 13:50 [PATCH RESEND v9 0/4] clk: meson: add a sub EMMC clock controller support Jianxin Pan
@ 2019-01-08 13:50 ` Jianxin Pan
2019-01-22 9:25 ` Jerome Brunet
2019-01-08 13:50 ` [PATCH v9 2/4] clk: meson: add emmc sub clock phase delay driver Jianxin Pan
` (2 subsequent siblings)
3 siblings, 1 reply; 12+ messages in thread
From: Jianxin Pan @ 2019-01-08 13:50 UTC (permalink / raw)
To: Jerome Brunet, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, Jianxin Pan, devicetree,
Stephen Boyd, Kevin Hilman, Michael Turquette, Yixun Lan,
linux-kernel, Boris Brezillon, Liang Yang, Jian Hu,
Miquel Raynal, Carlo Caione, linux-amlogic, Martin Blumenstingl,
linux-clk, linux-arm-kernel, Qiufang Dai
When CLK_DIVIDER_ONE_BASED flag is set, the sclk divider will be:
one based divider (div = val), and zero value gates the clock
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
---
drivers/clk/meson/Makefile | 3 ++-
drivers/clk/meson/clkc-audio.h | 8 ------
drivers/clk/meson/clkc.h | 10 ++++++-
drivers/clk/meson/sclk-div.c | 59 ++++++++++++++++++++++++++++--------------
4 files changed, 50 insertions(+), 30 deletions(-)
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index a849aa8..acd8694 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -4,7 +4,8 @@
obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-pll.o clk-mpll.o clk-phase.o vid-pll-div.o
obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-input.o
-obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o sclk-div.o
+obj-$(CONFIG_COMMON_CLK_AMLOGIC) += sclk-div.o
+obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o
obj-$(CONFIG_COMMON_CLK_MESON_AO) += meson-aoclk.o
obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o gxbb-aoclk-32k.o
diff --git a/drivers/clk/meson/clkc-audio.h b/drivers/clk/meson/clkc-audio.h
index 0a7c157..286ff12 100644
--- a/drivers/clk/meson/clkc-audio.h
+++ b/drivers/clk/meson/clkc-audio.h
@@ -15,14 +15,6 @@ struct meson_clk_triphase_data {
struct parm ph2;
};
-struct meson_sclk_div_data {
- struct parm div;
- struct parm hi;
- unsigned int cached_div;
- struct clk_duty cached_duty;
-};
-
extern const struct clk_ops meson_clk_triphase_ops;
-extern const struct clk_ops meson_sclk_div_ops;
#endif /* __MESON_CLKC_AUDIO_H */
diff --git a/drivers/clk/meson/clkc.h b/drivers/clk/meson/clkc.h
index 6183b22..00b3320 100644
--- a/drivers/clk/meson/clkc.h
+++ b/drivers/clk/meson/clkc.h
@@ -27,6 +27,14 @@ struct parm {
u8 width;
};
+struct meson_sclk_div_data {
+ struct parm div;
+ struct parm hi;
+ unsigned int cached_div;
+ struct clk_duty cached_duty;
+ u8 flags;
+};
+
static inline unsigned int meson_parm_read(struct regmap *map, struct parm *p)
{
unsigned int val;
@@ -118,10 +126,10 @@ struct clk_regmap _name = { \
extern const struct clk_ops meson_clk_mpll_ops;
extern const struct clk_ops meson_clk_phase_ops;
extern const struct clk_ops meson_vid_pll_div_ro_ops;
+extern const struct clk_ops meson_sclk_div_ops;
struct clk_hw *meson_clk_hw_register_input(struct device *dev,
const char *of_name,
const char *clk_name,
unsigned long flags);
-
#endif /* __CLKC_H */
diff --git a/drivers/clk/meson/sclk-div.c b/drivers/clk/meson/sclk-div.c
index bc64019..a6c425b 100644
--- a/drivers/clk/meson/sclk-div.c
+++ b/drivers/clk/meson/sclk-div.c
@@ -4,42 +4,60 @@
* Author: Jerome Brunet <jbrunet@baylibre.com>
*
* Sample clock generator divider:
- * This HW divider gates with value 0 but is otherwise a zero based divider:
+ * This HW divider gates with value 0
*
* val >= 1
- * divider = val + 1
+ * divider = val + 1 if ONE_BASED is not set, otherwise divider = val.
*
* The duty cycle may also be set for the LR clock variant. The duty cycle
* ratio is:
*
* hi = [0 - val]
- * duty_cycle = (1 + hi) / (1 + val)
+ * duty_cycle = (1 + hi) / (1 + val) if ONE_BASED is not set, otherwise:
+ * duty_cycle = hi / (1 + val)
*/
-#include "clkc-audio.h"
+#include "clkc.h"
-static inline struct meson_sclk_div_data *
-meson_sclk_div_data(struct clk_regmap *clk)
+static inline int get_reg(int val, unsigned char flag)
{
- return (struct meson_sclk_div_data *)clk->data;
+ WARN_ON(val < 1);
+ if ((flag & CLK_DIVIDER_ONE_BASED) || !val)
+ return val;
+ else
+ return val - 1;
+}
+
+static inline int get_value(int reg, unsigned char flag)
+{
+ if (flag & CLK_DIVIDER_ONE_BASED)
+ return reg;
+ else
+ return reg + 1;
}
-static int sclk_div_maxval(struct meson_sclk_div_data *sclk)
+static inline struct meson_sclk_div_data *
+meson_sclk_div_data(struct clk_regmap *clk)
{
- return (1 << sclk->div.width) - 1;
+ return (struct meson_sclk_div_data *)clk->data;
}
static int sclk_div_maxdiv(struct meson_sclk_div_data *sclk)
{
- return sclk_div_maxval(sclk) + 1;
+ unsigned int reg = clk_div_mask(sclk->div.width);
+
+ return get_value(reg, sclk->flags);
}
static int sclk_div_getdiv(struct clk_hw *hw, unsigned long rate,
unsigned long prate, int maxdiv)
{
int div = DIV_ROUND_CLOSEST_ULL((u64)prate, rate);
+ struct clk_regmap *clk = to_clk_regmap(hw);
+ struct meson_sclk_div_data *sclk = meson_sclk_div_data(clk);
+ int mindiv = get_value(1, sclk->flags);
- return clamp(div, 2, maxdiv);
+ return clamp(div, mindiv, maxdiv);
}
static int sclk_div_bestdiv(struct clk_hw *hw, unsigned long rate,
@@ -47,7 +65,7 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned long rate,
struct meson_sclk_div_data *sclk)
{
struct clk_hw *parent = clk_hw_get_parent(hw);
- int bestdiv = 0, i;
+ int bestdiv = 0, i, mindiv;
unsigned long maxdiv, now, parent_now;
unsigned long best = 0, best_parent = 0;
@@ -64,8 +82,9 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned long rate,
* unsigned long in rate * i below
*/
maxdiv = min(ULONG_MAX / rate, maxdiv);
+ mindiv = get_value(1, sclk->flags);
- for (i = 2; i <= maxdiv; i++) {
+ for (i = mindiv; i <= maxdiv; i++) {
/*
* It's the most ideal case if the requested rate can be
* divided from parent clock without needing to change
@@ -111,10 +130,7 @@ static void sclk_apply_ratio(struct clk_regmap *clk,
sclk->cached_duty.num,
sclk->cached_duty.den);
- if (hi)
- hi -= 1;
-
- meson_parm_write(clk->map, &sclk->hi, hi);
+ meson_parm_write(clk->map, &sclk->hi, get_reg(hi, sclk->flags));
}
static int sclk_div_set_duty_cycle(struct clk_hw *hw,
@@ -145,7 +161,7 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
}
hi = meson_parm_read(clk->map, &sclk->hi);
- duty->num = hi + 1;
+ duty->num = get_value(hi, sclk->flags);
duty->den = sclk->cached_div;
return 0;
}
@@ -153,10 +169,13 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
static void sclk_apply_divider(struct clk_regmap *clk,
struct meson_sclk_div_data *sclk)
{
+ unsigned int div;
+
if (MESON_PARM_APPLICABLE(&sclk->hi))
sclk_apply_ratio(clk, sclk);
- meson_parm_write(clk->map, &sclk->div, sclk->cached_div - 1);
+ div = get_reg(sclk->cached_div, sclk->flags);
+ meson_parm_write(clk->map, &sclk->div, div);
}
static int sclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
@@ -224,7 +243,7 @@ static void sclk_div_init(struct clk_hw *hw)
if (!val)
sclk->cached_div = sclk_div_maxdiv(sclk);
else
- sclk->cached_div = val + 1;
+ sclk->cached_div = get_value(val, sclk->flags);
sclk_div_get_duty_cycle(hw, &sclk->cached_duty);
}
--
1.9.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider
2019-01-08 13:50 ` [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider Jianxin Pan
@ 2019-01-22 9:25 ` Jerome Brunet
2019-01-24 9:10 ` Jianxin Pan
0 siblings, 1 reply; 12+ messages in thread
From: Jerome Brunet @ 2019-01-22 9:25 UTC (permalink / raw)
To: Jianxin Pan, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, devicetree, Stephen Boyd,
Kevin Hilman, Michael Turquette, Yixun Lan, linux-kernel,
Boris Brezillon, Liang Yang, Jian Hu, Miquel Raynal,
Carlo Caione, linux-amlogic, Martin Blumenstingl, linux-clk,
linux-arm-kernel, Qiufang Dai
On Tue, 2019-01-08 at 21:50 +0800, Jianxin Pan wrote:
> When CLK_DIVIDER_ONE_BASED flag is set, the sclk divider will be:
> one based divider (div = val), and zero value gates the clock
>
> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
> ---
> drivers/clk/meson/Makefile | 3 ++-
> drivers/clk/meson/clkc-audio.h | 8 ------
> drivers/clk/meson/clkc.h | 10 ++++++-
> drivers/clk/meson/sclk-div.c | 59 ++++++++++++++++++++++++++++-----------
> ---
> 4 files changed, 50 insertions(+), 30 deletions(-)
>
> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
> index a849aa8..acd8694 100644
> --- a/drivers/clk/meson/Makefile
> +++ b/drivers/clk/meson/Makefile
> @@ -4,7 +4,8 @@
>
> obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-pll.o clk-mpll.o clk-phase.o vid-
> pll-div.o
> obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-input.o
> -obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o sclk-div.o
> +obj-$(CONFIG_COMMON_CLK_AMLOGIC) += sclk-div.o
> +obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o
> obj-$(CONFIG_COMMON_CLK_MESON_AO) += meson-aoclk.o
> obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o gxbb-aoclk-
> 32k.o
> diff --git a/drivers/clk/meson/clkc-audio.h b/drivers/clk/meson/clkc-audio.h
> index 0a7c157..286ff12 100644
> --- a/drivers/clk/meson/clkc-audio.h
> +++ b/drivers/clk/meson/clkc-audio.h
> @@ -15,14 +15,6 @@ struct meson_clk_triphase_data {
> struct parm ph2;
> };
>
> -struct meson_sclk_div_data {
> - struct parm div;
> - struct parm hi;
> - unsigned int cached_div;
> - struct clk_duty cached_duty;
> -};
> -
> extern const struct clk_ops meson_clk_triphase_ops;
> -extern const struct clk_ops meson_sclk_div_ops;
>
> #endif /* __MESON_CLKC_AUDIO_H */
> diff --git a/drivers/clk/meson/clkc.h b/drivers/clk/meson/clkc.h
> index 6183b22..00b3320 100644
> --- a/drivers/clk/meson/clkc.h
> +++ b/drivers/clk/meson/clkc.h
> @@ -27,6 +27,14 @@ struct parm {
> u8 width;
> };
>
> +struct meson_sclk_div_data {
> + struct parm div;
> + struct parm hi;
> + unsigned int cached_div;
> + struct clk_duty cached_duty;
> + u8 flags;
> +};
> +
> static inline unsigned int meson_parm_read(struct regmap *map, struct parm
> *p)
> {
> unsigned int val;
> @@ -118,10 +126,10 @@ struct clk_regmap _name = {
> \
> extern const struct clk_ops meson_clk_mpll_ops;
> extern const struct clk_ops meson_clk_phase_ops;
> extern const struct clk_ops meson_vid_pll_div_ro_ops;
> +extern const struct clk_ops meson_sclk_div_ops;
>
> struct clk_hw *meson_clk_hw_register_input(struct device *dev,
> const char *of_name,
> const char *clk_name,
> unsigned long flags);
> -
> #endif /* __CLKC_H */
> diff --git a/drivers/clk/meson/sclk-div.c b/drivers/clk/meson/sclk-div.c
> index bc64019..a6c425b 100644
> --- a/drivers/clk/meson/sclk-div.c
> +++ b/drivers/clk/meson/sclk-div.c
> @@ -4,42 +4,60 @@
> * Author: Jerome Brunet <jbrunet@baylibre.com>
> *
> * Sample clock generator divider:
> - * This HW divider gates with value 0 but is otherwise a zero based
> divider:
> + * This HW divider gates with value 0
> *
> * val >= 1
> - * divider = val + 1
> + * divider = val + 1 if ONE_BASED is not set, otherwise divider = val.
> *
> * The duty cycle may also be set for the LR clock variant. The duty cycle
> * ratio is:
> *
> * hi = [0 - val]
> - * duty_cycle = (1 + hi) / (1 + val)
> + * duty_cycle = (1 + hi) / (1 + val) if ONE_BASED is not set, otherwise:
> + * duty_cycle = hi / (1 + val)
> */
>
> -#include "clkc-audio.h"
> +#include "clkc.h"
>
> -static inline struct meson_sclk_div_data *
> -meson_sclk_div_data(struct clk_regmap *clk)
> +static inline int get_reg(int val, unsigned char flag)
s/get_reg/sclk_get_reg
> {
> - return (struct meson_sclk_div_data *)clk->data;
> + WARN_ON(val < 1);
I don't think this WARN is justified, especially since you are using this
function to set the hi value.
> + if ((flag & CLK_DIVIDER_ONE_BASED) || !val)
I don't like that you make a dependency on the generic divider just for this.
Please make your own flag like MESON_SCLK_ONE_BASED
> + return val;
> + else
> + return val - 1;
> +}
> +
> +static inline int get_value(int reg, unsigned char flag)
s/get_value/sclk_get_divider
> +{
> + if (flag & CLK_DIVIDER_ONE_BASED)
> + return reg;
> + else
> + return reg + 1;
> }
>
> -static int sclk_div_maxval(struct meson_sclk_div_data *sclk)
> +static inline struct meson_sclk_div_data *
> +meson_sclk_div_data(struct clk_regmap *clk)
> {
> - return (1 << sclk->div.width) - 1;
> + return (struct meson_sclk_div_data *)clk->data;
> }
>
> static int sclk_div_maxdiv(struct meson_sclk_div_data *sclk)
> {
> - return sclk_div_maxval(sclk) + 1;
> + unsigned int reg = clk_div_mask(sclk->div.width);
same here, leave the generic divider alone.
`(1 << sclk->div.width) - 1` was fine to get max register value.
> +
> + return get_value(reg, sclk->flags);
> }
>
> static int sclk_div_getdiv(struct clk_hw *hw, unsigned long rate,
> unsigned long prate, int maxdiv)
> {
> int div = DIV_ROUND_CLOSEST_ULL((u64)prate, rate);
> + struct clk_regmap *clk = to_clk_regmap(hw);
> + struct meson_sclk_div_data *sclk = meson_sclk_div_data(clk);
> + int mindiv = get_value(1, sclk->flags);
maxdiv is provided as a param while mindiv is computed inside this function.
let's be coherent and pick one approach.
>
> - return clamp(div, 2, maxdiv);
> + return clamp(div, mindiv, maxdiv);
> }
>
> static int sclk_div_bestdiv(struct clk_hw *hw, unsigned long rate,
> @@ -47,7 +65,7 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
> long rate,
> struct meson_sclk_div_data *sclk)
> {
> struct clk_hw *parent = clk_hw_get_parent(hw);
> - int bestdiv = 0, i;
> + int bestdiv = 0, i, mindiv;
> unsigned long maxdiv, now, parent_now;
> unsigned long best = 0, best_parent = 0;
>
> @@ -64,8 +82,9 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
> long rate,
> * unsigned long in rate * i below
> */
> maxdiv = min(ULONG_MAX / rate, maxdiv);
> + mindiv = get_value(1, sclk->flags);
>
> - for (i = 2; i <= maxdiv; i++) {
> + for (i = mindiv; i <= maxdiv; i++) {
> /*
> * It's the most ideal case if the requested rate can be
> * divided from parent clock without needing to change
> @@ -111,10 +130,7 @@ static void sclk_apply_ratio(struct clk_regmap *clk,
> sclk->cached_duty.num,
> sclk->cached_duty.den);
>
> - if (hi)
> - hi -= 1;
> -
> - meson_parm_write(clk->map, &sclk->hi, hi);
> + meson_parm_write(clk->map, &sclk->hi, get_reg(hi, sclk->flags));
> }
>
> static int sclk_div_set_duty_cycle(struct clk_hw *hw,
> @@ -145,7 +161,7 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
> }
>
> hi = meson_parm_read(clk->map, &sclk->hi);
> - duty->num = hi + 1;
> + duty->num = get_value(hi, sclk->flags);
> duty->den = sclk->cached_div;
> return 0;
> }
> @@ -153,10 +169,13 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
> static void sclk_apply_divider(struct clk_regmap *clk,
> struct meson_sclk_div_data *sclk)
> {
> + unsigned int div;
> +
> if (MESON_PARM_APPLICABLE(&sclk->hi))
> sclk_apply_ratio(clk, sclk);
>
> - meson_parm_write(clk->map, &sclk->div, sclk->cached_div - 1);
> + div = get_reg(sclk->cached_div, sclk->flags);
> + meson_parm_write(clk->map, &sclk->div, div);
> }
>
> static int sclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
> @@ -224,7 +243,7 @@ static void sclk_div_init(struct clk_hw *hw)
> if (!val)
> sclk->cached_div = sclk_div_maxdiv(sclk);
> else
> - sclk->cached_div = val + 1;
> + sclk->cached_div = get_value(val, sclk->flags);
>
> sclk_div_get_duty_cycle(hw, &sclk->cached_duty);
> }
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider
2019-01-22 9:25 ` Jerome Brunet
@ 2019-01-24 9:10 ` Jianxin Pan
0 siblings, 0 replies; 12+ messages in thread
From: Jianxin Pan @ 2019-01-24 9:10 UTC (permalink / raw)
To: Jerome Brunet, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, devicetree, Stephen Boyd,
Kevin Hilman, Michael Turquette, Yixun Lan, linux-kernel,
Boris Brezillon, Liang Yang, Jian Hu, Miquel Raynal,
Carlo Caione, linux-amlogic, Martin Blumenstingl, linux-clk,
linux-arm-kernel, Qiufang Dai
Hi Jerome,
On 2019/1/22 17:25, Jerome Brunet wrote:
> On Tue, 2019-01-08 at 21:50 +0800, Jianxin Pan wrote:
>> When CLK_DIVIDER_ONE_BASED flag is set, the sclk divider will be:
>> one based divider (div = val), and zero value gates the clock
>>
>> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
>> ---
>> drivers/clk/meson/Makefile | 3 ++-
>> drivers/clk/meson/clkc-audio.h | 8 ------
>> drivers/clk/meson/clkc.h | 10 ++++++-
>> drivers/clk/meson/sclk-div.c | 59 ++++++++++++++++++++++++++++-----------
>> ---
>> 4 files changed, 50 insertions(+), 30 deletions(-)
>>
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index a849aa8..acd8694 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -4,7 +4,8 @@
>>
>> obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-pll.o clk-mpll.o clk-phase.o vid-
>> pll-div.o
>> obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-input.o
>> -obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o sclk-div.o
>> +obj-$(CONFIG_COMMON_CLK_AMLOGIC) += sclk-div.o
>> +obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o
>> obj-$(CONFIG_COMMON_CLK_MESON_AO) += meson-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o gxbb-aoclk-
>> 32k.o
>> diff --git a/drivers/clk/meson/clkc-audio.h b/drivers/clk/meson/clkc-audio.h
>> index 0a7c157..286ff12 100644
>> --- a/drivers/clk/meson/clkc-audio.h
>> +++ b/drivers/clk/meson/clkc-audio.h
>> @@ -15,14 +15,6 @@ struct meson_clk_triphase_data {
>> struct parm ph2;
>> };
>>
>> -struct meson_sclk_div_data {
>> - struct parm div;
>> - struct parm hi;
>> - unsigned int cached_div;
>> - struct clk_duty cached_duty;
>> -};
>> -
>> extern const struct clk_ops meson_clk_triphase_ops;
>> -extern const struct clk_ops meson_sclk_div_ops;
>>
>> #endif /* __MESON_CLKC_AUDIO_H */
>> diff --git a/drivers/clk/meson/clkc.h b/drivers/clk/meson/clkc.h
>> index 6183b22..00b3320 100644
>> --- a/drivers/clk/meson/clkc.h
>> +++ b/drivers/clk/meson/clkc.h
>> @@ -27,6 +27,14 @@ struct parm {
>> u8 width;
>> };
>>
>> +struct meson_sclk_div_data {
>> + struct parm div;
>> + struct parm hi;
>> + unsigned int cached_div;
>> + struct clk_duty cached_duty;
>> + u8 flags;
>> +};
>> +
>> static inline unsigned int meson_parm_read(struct regmap *map, struct parm
>> *p)
>> {
>> unsigned int val;
>> @@ -118,10 +126,10 @@ struct clk_regmap _name = {
>> \
>> extern const struct clk_ops meson_clk_mpll_ops;
>> extern const struct clk_ops meson_clk_phase_ops;
>> extern const struct clk_ops meson_vid_pll_div_ro_ops;
>> +extern const struct clk_ops meson_sclk_div_ops;
>>
>> struct clk_hw *meson_clk_hw_register_input(struct device *dev,
>> const char *of_name,
>> const char *clk_name,
>> unsigned long flags);
>> -
>> #endif /* __CLKC_H */
>> diff --git a/drivers/clk/meson/sclk-div.c b/drivers/clk/meson/sclk-div.c
>> index bc64019..a6c425b 100644
>> --- a/drivers/clk/meson/sclk-div.c
>> +++ b/drivers/clk/meson/sclk-div.c
>> @@ -4,42 +4,60 @@
>> * Author: Jerome Brunet <jbrunet@baylibre.com>
>> *
>> * Sample clock generator divider:
>> - * This HW divider gates with value 0 but is otherwise a zero based
>> divider:
>> + * This HW divider gates with value 0
>> *
>> * val >= 1
>> - * divider = val + 1
>> + * divider = val + 1 if ONE_BASED is not set, otherwise divider = val.
>> *
>> * The duty cycle may also be set for the LR clock variant. The duty cycle
>> * ratio is:
>> *
>> * hi = [0 - val]
>> - * duty_cycle = (1 + hi) / (1 + val)
>> + * duty_cycle = (1 + hi) / (1 + val) if ONE_BASED is not set, otherwise:
>> + * duty_cycle = hi / (1 + val)
>> */
>>
>> -#include "clkc-audio.h"
>> +#include "clkc.h"
>>
>> -static inline struct meson_sclk_div_data *
>> -meson_sclk_div_data(struct clk_regmap *clk)
>> +static inline int get_reg(int val, unsigned char flag)
>
> s/get_reg/sclk_get_reg
OK, I will rename get_reg and get_value in next version.
Thank you for the review.
>
>> {
>> - return (struct meson_sclk_div_data *)clk->data;
>> + WARN_ON(val < 1);
>
> I don't think this WARN is justified, especially since you are using this
> function to set the hi value.
OK, it will remove it. Thank you.
>
>> + if ((flag & CLK_DIVIDER_ONE_BASED) || !val)
>
> I don't like that you make a dependency on the generic divider just for this.
> Please make your own flag like MESON_SCLK_ONE_BASED
OK, I will define a new flag MESON_SCLK_ONE_BASED in drivers/clk/meson/clkc.h.
>
>> + return val;
>> + else
>> + return val - 1;
>> +}
>> +
>> +static inline int get_value(int reg, unsigned char flag)
>
> s/get_value/sclk_get_divider
OK, I will rename it.
>
>> +{
>> + if (flag & CLK_DIVIDER_ONE_BASED)
>> + return reg;
>> + else
>> + return reg + 1;
>> }
>>
>> -static int sclk_div_maxval(struct meson_sclk_div_data *sclk)
>> +static inline struct meson_sclk_div_data *
>> +meson_sclk_div_data(struct clk_regmap *clk)
>> {
>> - return (1 << sclk->div.width) - 1;
>> + return (struct meson_sclk_div_data *)clk->data;
>> }
>>
>> static int sclk_div_maxdiv(struct meson_sclk_div_data *sclk)
>> {
>> - return sclk_div_maxval(sclk) + 1;
>> + unsigned int reg = clk_div_mask(sclk->div.width);
>
> same here, leave the generic divider alone.
>
> `(1 << sclk->div.width) - 1` was fine to get max register value.
>
>> +
>> + return get_value(reg, sclk->flags);
>> }
>>
>> static int sclk_div_getdiv(struct clk_hw *hw, unsigned long rate,
>> unsigned long prate, int maxdiv)
>> {
>> int div = DIV_ROUND_CLOSEST_ULL((u64)prate, rate);
>> + struct clk_regmap *clk = to_clk_regmap(hw);
>> + struct meson_sclk_div_data *sclk = meson_sclk_div_data(clk);
>> + int mindiv = get_value(1, sclk->flags);
>
> maxdiv is provided as a param while mindiv is computed inside this function.
> let's be coherent and pick one approach.
OK, I will compute min and max in this function both.
Thank you for your review.
>
>>
>> - return clamp(div, 2, maxdiv);
>> + return clamp(div, mindiv, maxdiv);
>> }
>>
>> static int sclk_div_bestdiv(struct clk_hw *hw, unsigned long rate,
>> @@ -47,7 +65,7 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
>> long rate,
>> struct meson_sclk_div_data *sclk)
>> {
>> struct clk_hw *parent = clk_hw_get_parent(hw);
>> - int bestdiv = 0, i;
>> + int bestdiv = 0, i, mindiv;
>> unsigned long maxdiv, now, parent_now;
>> unsigned long best = 0, best_parent = 0;
>>
>> @@ -64,8 +82,9 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
>> long rate,
>> * unsigned long in rate * i below
>> */
>> maxdiv = min(ULONG_MAX / rate, maxdiv);
>> + mindiv = get_value(1, sclk->flags);
>>
>> - for (i = 2; i <= maxdiv; i++) {
>> + for (i = mindiv; i <= maxdiv; i++) {
>> /*
>> * It's the most ideal case if the requested rate can be
>> * divided from parent clock without needing to change
>> @@ -111,10 +130,7 @@ static void sclk_apply_ratio(struct clk_regmap *clk,
>> sclk->cached_duty.num,
>> sclk->cached_duty.den);
>>
>> - if (hi)
>> - hi -= 1;
>> -
>> - meson_parm_write(clk->map, &sclk->hi, hi);
>> + meson_parm_write(clk->map, &sclk->hi, get_reg(hi, sclk->flags));
>> }
>>
>> static int sclk_div_set_duty_cycle(struct clk_hw *hw,
>> @@ -145,7 +161,7 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
>> }
>>
>> hi = meson_parm_read(clk->map, &sclk->hi);
>> - duty->num = hi + 1;
>> + duty->num = get_value(hi, sclk->flags);
>> duty->den = sclk->cached_div;
>> return 0;
>> }
>> @@ -153,10 +169,13 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
>> static void sclk_apply_divider(struct clk_regmap *clk,
>> struct meson_sclk_div_data *sclk)
>> {
>> + unsigned int div;
>> +
>> if (MESON_PARM_APPLICABLE(&sclk->hi))
>> sclk_apply_ratio(clk, sclk);
>>
>> - meson_parm_write(clk->map, &sclk->div, sclk->cached_div - 1);
>> + div = get_reg(sclk->cached_div, sclk->flags);
>> + meson_parm_write(clk->map, &sclk->div, div);
>> }
>>
>> static int sclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
>> @@ -224,7 +243,7 @@ static void sclk_div_init(struct clk_hw *hw)
>> if (!val)
>> sclk->cached_div = sclk_div_maxdiv(sclk);
>> else
>> - sclk->cached_div = val + 1;
>> + sclk->cached_div = get_value(val, sclk->flags);
>>
>> sclk_div_get_duty_cycle(hw, &sclk->cached_duty);
>> }
>
>
> .
>
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v9 2/4] clk: meson: add emmc sub clock phase delay driver
2019-01-08 13:50 [PATCH RESEND v9 0/4] clk: meson: add a sub EMMC clock controller support Jianxin Pan
2019-01-08 13:50 ` [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider Jianxin Pan
@ 2019-01-08 13:50 ` Jianxin Pan
2019-01-08 13:50 ` [PATCH v9 3/4] clk: meson: add DT documentation for emmc clock controller Jianxin Pan
2019-01-08 13:50 ` [PATCH v9 4/4] clk: meson: add sub MMC clock controller driver Jianxin Pan
3 siblings, 0 replies; 12+ messages in thread
From: Jianxin Pan @ 2019-01-08 13:50 UTC (permalink / raw)
To: Jerome Brunet, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, Jianxin Pan, Stephen Boyd,
Kevin Hilman, Michael Turquette, Yixun Lan, linux-kernel,
Boris Brezillon, Liang Yang, Jian Hu, Miquel Raynal,
Carlo Caione, linux-amlogic, Martin Blumenstingl, linux-clk,
linux-arm-kernel, Qiufang Dai
From: Yixun Lan <yixun.lan@amlogic.com>
Export the emmc sub clock phase delay ops which will be used
by the emmc sub clock driver itself.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
---
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/clk-phase-delay.c | 73 +++++++++++++++++++++++++++++++++++++
drivers/clk/meson/clkc.h | 7 ++++
3 files changed, 81 insertions(+)
create mode 100644 drivers/clk/meson/clk-phase-delay.c
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index acd8694..d59620d 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -3,6 +3,7 @@
#
obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-pll.o clk-mpll.o clk-phase.o vid-pll-div.o
+obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-phase-delay.o
obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-input.o
obj-$(CONFIG_COMMON_CLK_AMLOGIC) += sclk-div.o
obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o
diff --git a/drivers/clk/meson/clk-phase-delay.c b/drivers/clk/meson/clk-phase-delay.c
new file mode 100644
index 0000000..a6e6600
--- /dev/null
+++ b/drivers/clk/meson/clk-phase-delay.c
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Amlogic Meson MMC Sub Clock Controller Driver
+ *
+ * Copyright (c) 2017 Baylibre SAS.
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ *
+ * Copyright (c) 2018 Amlogic, inc.
+ * Author: Yixun Lan <yixun.lan@amlogic.com>
+ * Author: Jianxin Pan <jianxin.pan@amlogic.com>
+ */
+
+#include <linux/clk-provider.h>
+#include "clkc.h"
+
+static inline struct meson_clk_phase_delay_data *
+meson_clk_get_phase_delay_data(struct clk_regmap *clk)
+{
+ return clk->data;
+}
+
+static int meson_clk_phase_delay_get_phase(struct clk_hw *hw)
+{
+ struct clk_regmap *clk = to_clk_regmap(hw);
+ struct meson_clk_phase_delay_data *ph;
+ unsigned long period_ps, p, d;
+ int degrees;
+
+ ph = meson_clk_get_phase_delay_data(clk);
+ p = meson_parm_read(clk->map, &ph->phase);
+ degrees = p * 360 / (1 << (ph->phase.width));
+
+ period_ps = DIV_ROUND_UP_ULL(NSEC_PER_SEC * 1000ull,
+ clk_hw_get_rate(hw));
+
+ d = meson_parm_read(clk->map, &ph->delay);
+ degrees += d * ph->delay_step_ps * 360 / period_ps;
+ degrees %= 360;
+
+ return degrees;
+}
+
+static int meson_clk_phase_delay_set_phase(struct clk_hw *hw, int degrees)
+{
+ struct clk_regmap *clk = to_clk_regmap(hw);
+ struct meson_clk_phase_delay_data *ph;
+ unsigned long period_ps, d = 0;
+ unsigned int p;
+
+ ph = meson_clk_get_phase_delay_data(clk);
+ period_ps = DIV_ROUND_UP_ULL(NSEC_PER_SEC * 1000ull,
+ clk_hw_get_rate(hw));
+
+ /*
+ * First compute the phase index (p), the remainder (r) is the
+ * part we'll try to acheive using the delays (d).
+ */
+ p = 360 / 1 << (ph->phase.width);
+ degrees = degrees / p;
+ d = DIV_ROUND_CLOSEST((degrees % p) * period_ps,
+ 360 * ph->delay_step_ps);
+ d = min(d, PMASK(ph->delay.width));
+
+ meson_parm_write(clk->map, &ph->phase, degrees);
+ meson_parm_write(clk->map, &ph->delay, d);
+ return 0;
+}
+
+const struct clk_ops meson_clk_phase_delay_ops = {
+ .get_phase = meson_clk_phase_delay_get_phase,
+ .set_phase = meson_clk_phase_delay_set_phase,
+};
+EXPORT_SYMBOL_GPL(meson_clk_phase_delay_ops);
diff --git a/drivers/clk/meson/clkc.h b/drivers/clk/meson/clkc.h
index 00b3320..e6f0905 100644
--- a/drivers/clk/meson/clkc.h
+++ b/drivers/clk/meson/clkc.h
@@ -118,6 +118,12 @@ struct clk_regmap _name = { \
}, \
};
+struct meson_clk_phase_delay_data {
+ struct parm phase;
+ struct parm delay;
+ unsigned int delay_step_ps;
+};
+
/* clk_ops */
extern const struct clk_ops meson_clk_pll_ro_ops;
extern const struct clk_ops meson_clk_pll_ops;
@@ -127,6 +133,7 @@ struct clk_regmap _name = { \
extern const struct clk_ops meson_clk_phase_ops;
extern const struct clk_ops meson_vid_pll_div_ro_ops;
extern const struct clk_ops meson_sclk_div_ops;
+extern const struct clk_ops meson_clk_phase_delay_ops;
struct clk_hw *meson_clk_hw_register_input(struct device *dev,
const char *of_name,
--
1.9.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v9 3/4] clk: meson: add DT documentation for emmc clock controller
2019-01-08 13:50 [PATCH RESEND v9 0/4] clk: meson: add a sub EMMC clock controller support Jianxin Pan
2019-01-08 13:50 ` [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider Jianxin Pan
2019-01-08 13:50 ` [PATCH v9 2/4] clk: meson: add emmc sub clock phase delay driver Jianxin Pan
@ 2019-01-08 13:50 ` Jianxin Pan
2019-01-22 9:27 ` Jerome Brunet
2019-01-08 13:50 ` [PATCH v9 4/4] clk: meson: add sub MMC clock controller driver Jianxin Pan
3 siblings, 1 reply; 12+ messages in thread
From: Jianxin Pan @ 2019-01-08 13:50 UTC (permalink / raw)
To: Jerome Brunet, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, Jianxin Pan, Stephen Boyd,
Kevin Hilman, Michael Turquette, Yixun Lan, linux-kernel,
Boris Brezillon, Liang Yang, Jian Hu, Miquel Raynal,
Carlo Caione, linux-amlogic, Martin Blumenstingl, linux-clk,
linux-arm-kernel, Qiufang Dai
From: Yixun Lan <yixun.lan@amlogic.com>
Document the MMC sub clock controller driver, the potential consumer
of this driver is MMC or NAND. Also add four clock bindings IDs which
provided by this driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
---
.../devicetree/bindings/clock/amlogic,mmc-clkc.txt | 39 ++++++++++++++++++++++
include/dt-bindings/clock/amlogic,mmc-clkc.h | 17 ++++++++++
2 files changed, 56 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,mmc-clkc.txt
create mode 100644 include/dt-bindings/clock/amlogic,mmc-clkc.h
diff --git a/Documentation/devicetree/bindings/clock/amlogic,mmc-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,mmc-clkc.txt
new file mode 100644
index 0000000..0f518e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/amlogic,mmc-clkc.txt
@@ -0,0 +1,39 @@
+* Amlogic MMC Sub Clock Controller Driver
+
+The Amlogic MMC clock controller generates and supplies clock to support
+MMC and NAND controller
+
+Required Properties:
+
+- compatible: should be:
+ "amlogic,gx-mmc-clkc"
+ "amlogic,axg-mmc-clkc"
+
+- #clock-cells: should be 1.
+- clocks: phandles to clocks corresponding to the clock-names property
+- clock-names: list of parent clock names
+ - "clkin0", "clkin1"
+
+- reg: address of emmc sub clock register
+
+Example: Clock controller node:
+
+sd_mmc_c_clkc: clock-controller@7000 {
+ compatible = "amlogic,axg-mmc-clkc", "syscon";
+ reg = <0x0 0x7000 0x0 0x4>;
+ #clock-cells = <1>;
+
+ clock-names = "clkin0", "clkin1";
+ clocks = <&clkc CLKID_SD_MMC_C_CLK0>,
+ <&clkc CLKID_FCLK_DIV2>;
+};
+
+sd_emmc_b_clkc: clock-controller@5000 {
+ compatible = "amlogic,axg-mmc-clkc", "syscon";
+ reg = <0x0 0x5000 0x0 0x4>;
+
+ #clock-cells = <1>;
+ clock-names = "clkin0", "clkin1";
+ clocks = <&clkc CLKID_SD_EMMC_B_CLK0>,
+ <&clkc CLKID_FCLK_DIV2>;
+};
diff --git a/include/dt-bindings/clock/amlogic,mmc-clkc.h b/include/dt-bindings/clock/amlogic,mmc-clkc.h
new file mode 100644
index 0000000..34a3c56
--- /dev/null
+++ b/include/dt-bindings/clock/amlogic,mmc-clkc.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Meson MMC sub clock tree IDs
+ *
+ * Copyright (c) 2018 Amlogic, Inc. All rights reserved.
+ * Author: Yixun Lan <yixun.lan@amlogic.com>
+ */
+
+#ifndef __MMC_CLKC_H
+#define __MMC_CLKC_H
+
+#define CLKID_MMC_DIV 0
+#define CLKID_MMC_PHASE_CORE 1
+#define CLKID_MMC_PHASE_TX 2
+#define CLKID_MMC_PHASE_RX 3
+
+#endif
--
1.9.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v9 3/4] clk: meson: add DT documentation for emmc clock controller
2019-01-08 13:50 ` [PATCH v9 3/4] clk: meson: add DT documentation for emmc clock controller Jianxin Pan
@ 2019-01-22 9:27 ` Jerome Brunet
0 siblings, 0 replies; 12+ messages in thread
From: Jerome Brunet @ 2019-01-22 9:27 UTC (permalink / raw)
To: Jianxin Pan, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, Stephen Boyd, Kevin Hilman,
Michael Turquette, Yixun Lan, linux-kernel, Boris Brezillon,
Liang Yang, Jian Hu, Miquel Raynal, Carlo Caione, linux-amlogic,
Martin Blumenstingl, linux-clk, linux-arm-kernel, Qiufang Dai
On Tue, 2019-01-08 at 21:50 +0800, Jianxin Pan wrote:
> From: Yixun Lan <yixun.lan@amlogic.com>
>
> Document the MMC sub clock controller driver, the potential consumer
> of this driver is MMC or NAND. Also add four clock bindings IDs which
> provided by this driver.
>
> Reviewed-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
> ---
> .../devicetree/bindings/clock/amlogic,mmc-clkc.txt | 39
> ++++++++++++++++++++++
> include/dt-bindings/clock/amlogic,mmc-clkc.h | 17 ++++++++++
> 2 files changed, 56 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/amlogic,mmc-
> clkc.txt
> create mode 100644 include/dt-bindings/clock/amlogic,mmc-clkc.h
>
> diff --git a/Documentation/devicetree/bindings/clock/amlogic,mmc-clkc.txt
> b/Documentation/devicetree/bindings/clock/amlogic,mmc-clkc.txt
> new file mode 100644
> index 0000000..0f518e6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/amlogic,mmc-clkc.txt
> @@ -0,0 +1,39 @@
> +* Amlogic MMC Sub Clock Controller Driver
> +
> +The Amlogic MMC clock controller generates and supplies clock to support
> +MMC and NAND controller
> +
> +Required Properties:
> +
> +- compatible: should be:
> + "amlogic,gx-mmc-clkc"
> + "amlogic,axg-mmc-clkc"
nitpick, missing is something to tell that only one is required, not both
for example `should be one of the following`
> +
> +- #clock-cells: should be 1.
> +- clocks: phandles to clocks corresponding to the clock-names property
> +- clock-names: list of parent clock names
> + - "clkin0", "clkin1"
> +
> +- reg: address of emmc sub clock register
> +
> +Example: Clock controller node:
> +
> +sd_mmc_c_clkc: clock-controller@7000 {
> + compatible = "amlogic,axg-mmc-clkc", "syscon";
> + reg = <0x0 0x7000 0x0 0x4>;
> + #clock-cells = <1>;
> +
> + clock-names = "clkin0", "clkin1";
> + clocks = <&clkc CLKID_SD_MMC_C_CLK0>,
> + <&clkc CLKID_FCLK_DIV2>;
> +};
> +
> +sd_emmc_b_clkc: clock-controller@5000 {
> + compatible = "amlogic,axg-mmc-clkc", "syscon";
> + reg = <0x0 0x5000 0x0 0x4>;
> +
> + #clock-cells = <1>;
> + clock-names = "clkin0", "clkin1";
> + clocks = <&clkc CLKID_SD_EMMC_B_CLK0>,
> + <&clkc CLKID_FCLK_DIV2>;
> +};
> diff --git a/include/dt-bindings/clock/amlogic,mmc-clkc.h b/include/dt-
> bindings/clock/amlogic,mmc-clkc.h
> new file mode 100644
> index 0000000..34a3c56
> --- /dev/null
> +++ b/include/dt-bindings/clock/amlogic,mmc-clkc.h
> @@ -0,0 +1,17 @@
> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
> +/*
> + * Meson MMC sub clock tree IDs
> + *
> + * Copyright (c) 2018 Amlogic, Inc. All rights reserved.
> + * Author: Yixun Lan <yixun.lan@amlogic.com>
> + */
> +
> +#ifndef __MMC_CLKC_H
> +#define __MMC_CLKC_H
> +
> +#define CLKID_MMC_DIV 0
> +#define CLKID_MMC_PHASE_CORE 1
> +#define CLKID_MMC_PHASE_TX 2
> +#define CLKID_MMC_PHASE_RX 3
> +
> +#endif
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v9 4/4] clk: meson: add sub MMC clock controller driver
2019-01-08 13:50 [PATCH RESEND v9 0/4] clk: meson: add a sub EMMC clock controller support Jianxin Pan
` (2 preceding siblings ...)
2019-01-08 13:50 ` [PATCH v9 3/4] clk: meson: add DT documentation for emmc clock controller Jianxin Pan
@ 2019-01-08 13:50 ` Jianxin Pan
2019-01-22 9:25 ` Jerome Brunet
3 siblings, 1 reply; 12+ messages in thread
From: Jianxin Pan @ 2019-01-08 13:50 UTC (permalink / raw)
To: Jerome Brunet, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, Jianxin Pan, Stephen Boyd,
Kevin Hilman, Michael Turquette, Yixun Lan, linux-kernel,
Boris Brezillon, Liang Yang, Jian Hu, Miquel Raynal,
Carlo Caione, linux-amlogic, Martin Blumenstingl, linux-clk,
linux-arm-kernel, Qiufang Dai
From: Yixun Lan <yixun.lan@amlogic.com>
The patch will add a MMC clock controller driver which used by MMC or NAND,
It provide a mux and divider clock, and three phase clocks - core, tx, tx.
Two clocks are provided as the parent of MMC clock controller from
upper layer clock controller - eg "amlogic,axg-clkc" in AXG platform.
To specify which clock the MMC or NAND driver may consume,
the preprocessor macros in the dt-bindings/clock/amlogic,mmc-clkc.h header
can be used in the device tree sources.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
---
drivers/clk/meson/Kconfig | 10 ++
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/mmc-clkc.c | 304 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 315 insertions(+)
create mode 100644 drivers/clk/meson/mmc-clkc.c
diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index efaa70f..3555f9d 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -15,6 +15,16 @@ config COMMON_CLK_MESON_AO
select COMMON_CLK_REGMAP_MESON
select RESET_CONTROLLER
+config COMMON_CLK_MMC_MESON
+ tristate "Meson MMC Sub Clock Controller Driver"
+ depends on ARCH_MESON || COMPILE_TEST
+ select MFD_SYSCON
+ select COMMON_CLK_AMLOGIC
+ help
+ Support for the MMC sub clock controller on Amlogic Meson Platform,
+ which include S905 (GXBB, GXL), A113D/X (AXG) devices.
+ Say Y if you want this clock enabled.
+
config COMMON_CLK_REGMAP_MESON
bool
select REGMAP
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index d59620d..54416a2 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -12,4 +12,5 @@ obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o gxbb-aoclk-32k.o
obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
+obj-$(CONFIG_COMMON_CLK_MMC_MESON) += mmc-clkc.o
obj-$(CONFIG_COMMON_CLK_REGMAP_MESON) += clk-regmap.o
diff --git a/drivers/clk/meson/mmc-clkc.c b/drivers/clk/meson/mmc-clkc.c
new file mode 100644
index 0000000..2582a98
--- /dev/null
+++ b/drivers/clk/meson/mmc-clkc.c
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Amlogic Meson MMC Sub Clock Controller Driver
+ *
+ * Copyright (c) 2017 Baylibre SAS.
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ *
+ * Copyright (c) 2018 Amlogic, inc.
+ * Author: Yixun Lan <yixun.lan@amlogic.com>
+ * Author: Jianxin Pan <jianxin.pan@amlogic.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/of_device.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/clock/amlogic,mmc-clkc.h>
+
+#include "clkc.h"
+
+/* clock ID used by internal driver */
+
+#define SD_EMMC_CLOCK 0
+#define CLK_DELAY_STEP_PS 200
+#define MUX_CLK_NUM_PARENTS 2
+#define MMC_MAX_CLKS 4
+
+struct mmc_clkc_data {
+ struct meson_clk_phase_delay_data tx;
+ struct meson_clk_phase_delay_data rx;
+};
+
+static struct clk_regmap_mux_data mmc_clkc_mux_data = {
+ .offset = SD_EMMC_CLOCK,
+ .mask = 0x3,
+ .shift = 6,
+};
+
+static const struct meson_sclk_div_data mmc_clkc_div_data = {
+ .div = {
+ .reg_off = SD_EMMC_CLOCK,
+ .width = 6,
+ },
+ .flags = CLK_DIVIDER_ONE_BASED,
+};
+
+static struct meson_clk_phase_data mmc_clkc_core_phase = {
+ .ph = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 8,
+ .width = 2,
+ }
+};
+
+static const struct mmc_clkc_data mmc_clkc_gx_data = {
+ .tx = {
+ .phase = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 10,
+ .width = 2,
+ },
+ .delay = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 16,
+ .width = 4,
+ },
+ .delay_step_ps = CLK_DELAY_STEP_PS,
+ },
+ .rx = {
+ .phase = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 12,
+ .width = 2,
+ },
+ .delay = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 20,
+ .width = 4,
+ },
+ .delay_step_ps = CLK_DELAY_STEP_PS,
+ },
+};
+
+static const struct mmc_clkc_data mmc_clkc_axg_data = {
+ .tx = {
+ .phase = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 10,
+ .width = 2,
+ },
+ .delay = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 16,
+ .width = 6,
+ },
+ .delay_step_ps = CLK_DELAY_STEP_PS,
+ },
+ .rx = {
+ .phase = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 12,
+ .width = 2,
+ },
+ .delay = {
+ .reg_off = SD_EMMC_CLOCK,
+ .shift = 22,
+ .width = 6,
+ },
+ .delay_step_ps = CLK_DELAY_STEP_PS,
+ },
+};
+
+static const struct of_device_id mmc_clkc_match_table[] = {
+ {
+ .compatible = "amlogic,gx-mmc-clkc",
+ .data = &mmc_clkc_gx_data
+ },
+ {
+ .compatible = "amlogic,axg-mmc-clkc",
+ .data = &mmc_clkc_axg_data
+ },
+ {}
+};
+MODULE_DEVICE_TABLE(of, mmc_clkc_match_table);
+
+static struct clk_regmap *
+mmc_clkc_register_clk(struct device *dev, struct regmap *map,
+ struct clk_init_data *init,
+ const char *suffix, void *data)
+{
+ struct clk_regmap *clk;
+ char *name;
+ int ret;
+
+ clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
+ if (!clk)
+ return ERR_PTR(-ENOMEM);
+
+ name = kasprintf(GFP_KERNEL, "%s#%s", dev_name(dev), suffix);
+ if (!name)
+ return ERR_PTR(-ENOMEM);
+
+ init->name = name;
+ clk->map = map;
+ clk->data = data;
+ clk->hw.init = init;
+ ret = devm_clk_hw_register(dev, &clk->hw);
+ if (ret)
+ clk = ERR_PTR(ret);
+
+ kfree(name);
+ return clk;
+}
+
+static struct clk_regmap *mmc_clkc_register_mux(struct device *dev,
+ struct regmap *map)
+{
+ const char *parent_names[MUX_CLK_NUM_PARENTS];
+ struct clk_init_data init;
+ struct clk_regmap *mux;
+ struct clk *clk;
+ int i;
+
+ for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) {
+ char name[8];
+
+ snprintf(name, sizeof(name), "clkin%d", i);
+ clk = devm_clk_get(dev, name);
+ if (IS_ERR(clk)) {
+ if (clk != ERR_PTR(-EPROBE_DEFER))
+ dev_err(dev, "Missing clock %s\n", name);
+ return ERR_CAST(clk);
+ }
+
+ parent_names[i] = __clk_get_name(clk);
+ }
+
+ init.ops = &clk_regmap_mux_ops;
+ init.flags = CLK_SET_RATE_PARENT;
+ init.parent_names = parent_names;
+ init.num_parents = MUX_CLK_NUM_PARENTS;
+
+ mux = mmc_clkc_register_clk(dev, map, &init, "mux", &mmc_clkc_mux_data);
+ if (IS_ERR(mux))
+ dev_err(dev, "Mux clock registration failed\n");
+
+ return mux;
+}
+
+static struct clk_regmap *
+mmc_clkc_register_clk_with_parent(struct device *dev, struct regmap *map,
+ char *suffix, const struct clk_hw *hw,
+ unsigned long flags,
+ const struct clk_ops *ops, void *data)
+{
+ struct clk_init_data init;
+ struct clk_regmap *clk;
+ const char *parent_name = clk_hw_get_name(hw);
+
+ init.ops = ops;
+ init.flags = flags;
+ init.parent_names = &parent_name;
+ init.num_parents = 1;
+
+ clk = mmc_clkc_register_clk(dev, map, &init, suffix, data);
+ if (IS_ERR(clk))
+ dev_err(dev, "%s clock registration failed\n", suffix);
+
+ return clk;
+}
+
+static int mmc_clkc_probe(struct platform_device *pdev)
+{
+ struct clk_hw_onecell_data *onecell_data;
+ struct device *dev = &pdev->dev;
+ struct mmc_clkc_data *data;
+ struct regmap *map;
+ struct clk_regmap *clk, *core;
+ struct meson_sclk_div_data *div_data;
+
+ /*cast to drop the const in match->data*/
+ data = (struct mmc_clkc_data *)of_device_get_match_data(dev);
+ if (!data)
+ return -ENODEV;
+
+ map = syscon_node_to_regmap(dev->of_node);
+ if (IS_ERR(map)) {
+ dev_err(dev, "could not find mmc clock controller\n");
+ return PTR_ERR(map);
+ }
+
+ onecell_data = devm_kzalloc(dev, sizeof(*onecell_data) +
+ sizeof(*onecell_data->hws) * MMC_MAX_CLKS,
+ GFP_KERNEL);
+ if (!onecell_data)
+ return -ENOMEM;
+
+ clk = mmc_clkc_register_mux(dev, map);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ div_data = devm_kzalloc(dev, sizeof(*div_data), GFP_KERNEL);
+ if (!div_data)
+ return -ENOMEM;
+
+ memcpy(div_data, &mmc_clkc_div_data, sizeof(*div_data));
+ clk = mmc_clkc_register_clk_with_parent(dev, map, "div",
+ &clk->hw,
+ CLK_SET_RATE_PARENT,
+ &meson_sclk_div_ops,
+ div_data);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ onecell_data->hws[CLKID_MMC_DIV] = &clk->hw,
+
+ core = mmc_clkc_register_clk_with_parent(dev, map, "core",
+ &clk->hw,
+ CLK_SET_RATE_PARENT,
+ &meson_clk_phase_ops,
+ &mmc_clkc_core_phase);
+ if (IS_ERR(core))
+ return PTR_ERR(core);
+
+ onecell_data->hws[CLKID_MMC_PHASE_CORE] = &core->hw,
+
+ clk = mmc_clkc_register_clk_with_parent(dev, map, "rx",
+ &core->hw, 0,
+ &meson_clk_phase_delay_ops,
+ &data->rx);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ onecell_data->hws[CLKID_MMC_PHASE_RX] = &clk->hw,
+ clk = mmc_clkc_register_clk_with_parent(dev, map, "tx",
+ &core->hw, 0,
+ &meson_clk_phase_delay_ops,
+ &data->tx);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ onecell_data->hws[CLKID_MMC_PHASE_TX] = &clk->hw,
+ onecell_data->num = MMC_MAX_CLKS;
+ return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
+ onecell_data);
+}
+
+static struct platform_driver mmc_clkc_driver = {
+ .probe = mmc_clkc_probe,
+ .driver = {
+ .name = "meson-mmc-clkc",
+ .of_match_table = of_match_ptr(mmc_clkc_match_table),
+ },
+};
+
+module_platform_driver(mmc_clkc_driver);
+
+MODULE_DESCRIPTION("Amlogic AXG MMC clock driver");
+MODULE_AUTHOR("Jianxin Pan <jianxin.pan@amlogic.com>");
+MODULE_LICENSE("GPL v2");
--
1.9.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v9 4/4] clk: meson: add sub MMC clock controller driver
2019-01-08 13:50 ` [PATCH v9 4/4] clk: meson: add sub MMC clock controller driver Jianxin Pan
@ 2019-01-22 9:25 ` Jerome Brunet
0 siblings, 0 replies; 12+ messages in thread
From: Jerome Brunet @ 2019-01-22 9:25 UTC (permalink / raw)
To: Jianxin Pan, Neil Armstrong
Cc: Rob Herring, Hanjie Lin, Victor Wan, Stephen Boyd, Kevin Hilman,
Michael Turquette, Yixun Lan, linux-kernel, Boris Brezillon,
Liang Yang, Jian Hu, Miquel Raynal, Carlo Caione, linux-amlogic,
Martin Blumenstingl, linux-clk, linux-arm-kernel, Qiufang Dai
On Tue, 2019-01-08 at 21:50 +0800, Jianxin Pan wrote:
> From: Yixun Lan <yixun.lan@amlogic.com>
>
> The patch will add a MMC clock controller driver which used by MMC or NAND,
> It provide a mux and divider clock, and three phase clocks - core, tx, tx.
>
> Two clocks are provided as the parent of MMC clock controller from
> upper layer clock controller - eg "amlogic,axg-clkc" in AXG platform.
>
> To specify which clock the MMC or NAND driver may consume,
> the preprocessor macros in the dt-bindings/clock/amlogic,mmc-clkc.h header
> can be used in the device tree sources.
>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
> ---
> drivers/clk/meson/Kconfig | 10 ++
> drivers/clk/meson/Makefile | 1 +
> drivers/clk/meson/mmc-clkc.c | 304
> +++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 315 insertions(+)
> create mode 100644 drivers/clk/meson/mmc-clkc.c
>
> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
> index efaa70f..3555f9d 100644
> --- a/drivers/clk/meson/Kconfig
> +++ b/drivers/clk/meson/Kconfig
> @@ -15,6 +15,16 @@ config COMMON_CLK_MESON_AO
> select COMMON_CLK_REGMAP_MESON
> select RESET_CONTROLLER
>
> +config COMMON_CLK_MMC_MESON
> + tristate "Meson MMC Sub Clock Controller Driver"
> + depends on ARCH_MESON || COMPILE_TEST
> + select MFD_SYSCON
> + select COMMON_CLK_AMLOGIC
> + help
> + Support for the MMC sub clock controller on Amlogic Meson Platform,
> + which include S905 (GXBB, GXL), A113D/X (AXG) devices.
> + Say Y if you want this clock enabled.
> +
> config COMMON_CLK_REGMAP_MESON
> bool
> select REGMAP
> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
> index d59620d..54416a2 100644
> --- a/drivers/clk/meson/Makefile
> +++ b/drivers/clk/meson/Makefile
> @@ -12,4 +12,5 @@ obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o gxbb-aoclk-
> 32k.o
> obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
> obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
> +obj-$(CONFIG_COMMON_CLK_MMC_MESON) += mmc-clkc.o
> obj-$(CONFIG_COMMON_CLK_REGMAP_MESON) += clk-regmap.o
> diff --git a/drivers/clk/meson/mmc-clkc.c b/drivers/clk/meson/mmc-clkc.c
> new file mode 100644
> index 0000000..2582a98
> --- /dev/null
> +++ b/drivers/clk/meson/mmc-clkc.c
> @@ -0,0 +1,304 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Amlogic Meson MMC Sub Clock Controller Driver
> + *
> + * Copyright (c) 2017 Baylibre SAS.
> + * Author: Jerome Brunet <jbrunet@baylibre.com>
> + *
> + * Copyright (c) 2018 Amlogic, inc.
> + * Author: Yixun Lan <yixun.lan@amlogic.com>
> + * Author: Jianxin Pan <jianxin.pan@amlogic.com>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/of_device.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/platform_device.h>
> +#include <dt-bindings/clock/amlogic,mmc-clkc.h>
> +
> +#include "clkc.h"
> +
> +/* clock ID used by internal driver */
> +
> +#define SD_EMMC_CLOCK 0
> +#define CLK_DELAY_STEP_PS 200
> +#define MUX_CLK_NUM_PARENTS 2
> +#define MMC_MAX_CLKS 4
> +
> +struct mmc_clkc_data {
> + struct meson_clk_phase_delay_data tx;
> + struct meson_clk_phase_delay_data rx;
> +};
> +
> +static struct clk_regmap_mux_data mmc_clkc_mux_data = {
> + .offset = SD_EMMC_CLOCK,
> + .mask = 0x3,
> + .shift = 6,
> +};
> +
> +static const struct meson_sclk_div_data mmc_clkc_div_data = {
> + .div = {
> + .reg_off = SD_EMMC_CLOCK,
> + .width = 6,
> + },
> + .flags = CLK_DIVIDER_ONE_BASED,
> +};
> +
> +static struct meson_clk_phase_data mmc_clkc_core_phase = {
> + .ph = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 8,
> + .width = 2,
> + }
> +};
> +
> +static const struct mmc_clkc_data mmc_clkc_gx_data = {
> + .tx = {
> + .phase = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 10,
> + .width = 2,
> + },
> + .delay = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 16,
> + .width = 4,
> + },
> + .delay_step_ps = CLK_DELAY_STEP_PS,
> + },
> + .rx = {
> + .phase = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 12,
> + .width = 2,
> + },
> + .delay = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 20,
> + .width = 4,
> + },
> + .delay_step_ps = CLK_DELAY_STEP_PS,
> + },
> +};
> +
> +static const struct mmc_clkc_data mmc_clkc_axg_data = {
> + .tx = {
> + .phase = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 10,
> + .width = 2,
> + },
> + .delay = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 16,
> + .width = 6,
> + },
> + .delay_step_ps = CLK_DELAY_STEP_PS,
Please check this. The delay step is not 200ns on the AXG.
> + },
> + .rx = {
> + .phase = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 12,
> + .width = 2,
> + },
> + .delay = {
> + .reg_off = SD_EMMC_CLOCK,
> + .shift = 22,
> + .width = 6,
> + },
> + .delay_step_ps = CLK_DELAY_STEP_PS,
> + },
> +};
> +
> +static const struct of_device_id mmc_clkc_match_table[] = {
> + {
> + .compatible = "amlogic,gx-mmc-clkc",
> + .data = &mmc_clkc_gx_data
> + },
> + {
> + .compatible = "amlogic,axg-mmc-clkc",
> + .data = &mmc_clkc_axg_data
> + },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mmc_clkc_match_table);
> +
> +static struct clk_regmap *
> +mmc_clkc_register_clk(struct device *dev, struct regmap *map,
> + struct clk_init_data *init,
> + const char *suffix, void *data)
> +{
> + struct clk_regmap *clk;
> + char *name;
> + int ret;
> +
> + clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
> + if (!clk)
> + return ERR_PTR(-ENOMEM);
> +
> + name = kasprintf(GFP_KERNEL, "%s#%s", dev_name(dev), suffix);
> + if (!name)
> + return ERR_PTR(-ENOMEM);
> +
> + init->name = name;
> + clk->map = map;
> + clk->data = data;
> + clk->hw.init = init;
> + ret = devm_clk_hw_register(dev, &clk->hw);
> + if (ret)
> + clk = ERR_PTR(ret);
> +
> + kfree(name);
> + return clk;
> +}
> +
> +static struct clk_regmap *mmc_clkc_register_mux(struct device *dev,
> + struct regmap *map)
> +{
> + const char *parent_names[MUX_CLK_NUM_PARENTS];
> + struct clk_init_data init;
> + struct clk_regmap *mux;
> + struct clk *clk;
> + int i;
> +
> + for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) {
> + char name[8];
> +
> + snprintf(name, sizeof(name), "clkin%d", i);
> + clk = devm_clk_get(dev, name);
> + if (IS_ERR(clk)) {
> + if (clk != ERR_PTR(-EPROBE_DEFER))
> + dev_err(dev, "Missing clock %s\n", name);
> + return ERR_CAST(clk);
> + }
> +
> + parent_names[i] = __clk_get_name(clk);
> + }
> +
> + init.ops = &clk_regmap_mux_ops;
> + init.flags = CLK_SET_RATE_PARENT;
> + init.parent_names = parent_names;
> + init.num_parents = MUX_CLK_NUM_PARENTS;
> +
> + mux = mmc_clkc_register_clk(dev, map, &init, "mux",
> &mmc_clkc_mux_data);
> + if (IS_ERR(mux))
> + dev_err(dev, "Mux clock registration failed\n");
> +
> + return mux;
> +}
> +
> +static struct clk_regmap *
> +mmc_clkc_register_clk_with_parent(struct device *dev, struct regmap *map,
> + char *suffix, const struct clk_hw *hw,
> + unsigned long flags,
> + const struct clk_ops *ops, void *data)
> +{
> + struct clk_init_data init;
> + struct clk_regmap *clk;
> + const char *parent_name = clk_hw_get_name(hw);
> +
> + init.ops = ops;
> + init.flags = flags;
> + init.parent_names = &parent_name;
> + init.num_parents = 1;
> +
> + clk = mmc_clkc_register_clk(dev, map, &init, suffix, data);
> + if (IS_ERR(clk))
> + dev_err(dev, "%s clock registration failed\n", suffix);
> +
> + return clk;
> +}
> +
> +static int mmc_clkc_probe(struct platform_device *pdev)
> +{
> + struct clk_hw_onecell_data *onecell_data;
> + struct device *dev = &pdev->dev;
> + struct mmc_clkc_data *data;
> + struct regmap *map;
> + struct clk_regmap *clk, *core;
> + struct meson_sclk_div_data *div_data;
> +
> + /*cast to drop the const in match->data*/
> + data = (struct mmc_clkc_data *)of_device_get_match_data(dev);
> + if (!data)
> + return -ENODEV;
> +
> + map = syscon_node_to_regmap(dev->of_node);
> + if (IS_ERR(map)) {
> + dev_err(dev, "could not find mmc clock controller\n");
> + return PTR_ERR(map);
> + }
> +
> + onecell_data = devm_kzalloc(dev, sizeof(*onecell_data) +
> + sizeof(*onecell_data->hws) * MMC_MAX_CLKS,
> + GFP_KERNEL);
> + if (!onecell_data)
> + return -ENOMEM;
> +
> + clk = mmc_clkc_register_mux(dev, map);
> + if (IS_ERR(clk))
> + return PTR_ERR(clk);
> +
> + div_data = devm_kzalloc(dev, sizeof(*div_data), GFP_KERNEL);
> + if (!div_data)
> + return -ENOMEM;
> +
> + memcpy(div_data, &mmc_clkc_div_data, sizeof(*div_data));
> + clk = mmc_clkc_register_clk_with_parent(dev, map, "div",
> + &clk->hw,
> + CLK_SET_RATE_PARENT,
> + &meson_sclk_div_ops,
> + div_data);
> + if (IS_ERR(clk))
> + return PTR_ERR(clk);
> +
> + onecell_data->hws[CLKID_MMC_DIV] = &clk->hw,
> +
> + core = mmc_clkc_register_clk_with_parent(dev, map, "core",
> + &clk->hw,
> + CLK_SET_RATE_PARENT,
> + &meson_clk_phase_ops,
> + &mmc_clkc_core_phase);
> + if (IS_ERR(core))
> + return PTR_ERR(core);
> +
> + onecell_data->hws[CLKID_MMC_PHASE_CORE] = &core->hw,
> +
> + clk = mmc_clkc_register_clk_with_parent(dev, map, "rx",
> + &core->hw, 0,
> + &meson_clk_phase_delay_ops,
> + &data->rx);
> + if (IS_ERR(clk))
> + return PTR_ERR(clk);
> +
> + onecell_data->hws[CLKID_MMC_PHASE_RX] = &clk->hw,
> + clk = mmc_clkc_register_clk_with_parent(dev, map, "tx",
> + &core->hw, 0,
> + &meson_clk_phase_delay_ops,
> + &data->tx);
> + if (IS_ERR(clk))
> + return PTR_ERR(clk);
> +
> + onecell_data->hws[CLKID_MMC_PHASE_TX] = &clk->hw,
> + onecell_data->num = MMC_MAX_CLKS;
> + return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
> + onecell_data);
> +}
> +
> +static struct platform_driver mmc_clkc_driver = {
> + .probe = mmc_clkc_probe,
> + .driver = {
> + .name = "meson-mmc-clkc",
> + .of_match_table = of_match_ptr(mmc_clkc_match_table),
> + },
> +};
> +
> +module_platform_driver(mmc_clkc_driver);
> +
> +MODULE_DESCRIPTION("Amlogic AXG MMC clock driver");
> +MODULE_AUTHOR("Jianxin Pan <jianxin.pan@amlogic.com>");
> +MODULE_LICENSE("GPL v2");
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread