Linux-Amlogic Archive on lore.kernel.org
 help / color / Atom feed
From: guillaume La Roque <glaroque@baylibre.com>
To: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
	khilman@baylibre.com, linus.walleij@linaro.org,
	linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
	robh+dt@kernel.org, linux-amlogic@lists.infradead.org
Subject: Re: [PATCH v2 4/4] pinctrl: meson: add support of drive-strength-uA
Date: Tue, 30 Apr 2019 09:20:39 +0200
Message-ID: <163fa4df-1017-d230-b264-51ea71236df9@baylibre.com> (raw)
In-Reply-To: <CAFBinCDNz1txJ7_aQU8MwjpeVFC6BgyG_gkg-jJRnnerSjbP9A@mail.gmail.com>

Hi Martin,


thanks for your feedback.


On 4/27/19 9:44 PM, Martin Blumenstingl wrote:
> Hi Guillaume,
>
> On Thu, Apr 18, 2019 at 2:48 PM Guillaume La Roque
> <glaroque@baylibre.com> wrote:
>> drive-strength-uA is a new feature needed for G12A SoC.
>> the default DS setting after boot is usually 500uA and it is not enough for
>> many functions. We need to be able to set the drive strength to reliably
>> enable things like MMC, I2C, etc ...
>>
>> Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
> I gave this a go on Meson8m2 (meaning I applied all four patches from
> this series and booted the result on my board):
> [Meson8m2 doesn't support drive strength and still boots without any
> crashes or obvious regressions]
> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>
>> ---
>>  drivers/pinctrl/meson/pinctrl-meson-g12a.c |  36 ++---
>>  drivers/pinctrl/meson/pinctrl-meson.c      | 166 ++++++++++++++++-----
>>  drivers/pinctrl/meson/pinctrl-meson.h      |  20 ++-
> personally I would have split this into two separate patches:
> - one for the generic pinctrl-meson part which adds drive-strength-uA support
> - another patch for enabling this on G12A
>
> if nobody else wants you to split this then it's fine for me as well


why not if i send new series i will do.


>
>>  3 files changed, 163 insertions(+), 59 deletions(-)
>>
>> diff --git a/drivers/pinctrl/meson/pinctrl-meson-g12a.c b/drivers/pinctrl/meson/pinctrl-meson-g12a.c
>> index d494492e98e9..3475cd7bd2af 100644
>> --- a/drivers/pinctrl/meson/pinctrl-meson-g12a.c
>> +++ b/drivers/pinctrl/meson/pinctrl-meson-g12a.c
>> @@ -1304,28 +1304,28 @@ static struct meson_pmx_func meson_g12a_aobus_functions[] = {
>>  };
>>
>>  static struct meson_bank meson_g12a_periphs_banks[] = {
>> -       /* name  first  last  irq  pullen  pull  dir  out  in */
>> -       BANK("Z",    GPIOZ_0,    GPIOZ_15, 12, 27,
>> -            4,  0,  4,  0,  12,  0,  13, 0,  14, 0),
>> -       BANK("H",    GPIOH_0,    GPIOH_8, 28, 36,
>> -            3,  0,  3,  0,  9,  0,  10,  0,  11,  0),
>> -       BANK("BOOT", BOOT_0,     BOOT_15,  37, 52,
>> -            0,  0,  0,  0,  0, 0,  1, 0,  2, 0),
>> -       BANK("C",    GPIOC_0,    GPIOC_7,  53, 60,
>> -            1,  0,  1,  0,  3, 0,  4, 0,  5, 0),
>> -       BANK("A",    GPIOA_0,    GPIOA_15,  61, 76,
>> -            5,  0,  5,  0,  16,  0,  17,  0,  18,  0),
>> -       BANK("X",    GPIOX_0,    GPIOX_19,   77, 96,
>> -            2,  0,  2,  0,  6,  0,  7,  0,  8,  0),
>> +       /* name  first  last  irq  pullen  pull  dir  out  in  ds */
>> +       BANK_DS("Z",    GPIOZ_0,    GPIOZ_15, 12, 27,
>> +               4,  0,  4,  0,  12,  0,  13, 0,  14, 0, 5, 0),
>> +       BANK_DS("H",    GPIOH_0,    GPIOH_8, 28, 36,
>> +               3,  0,  3,  0,  9,  0,  10,  0,  11,  0, 4, 0),
>> +       BANK_DS("BOOT", BOOT_0,     BOOT_15,  37, 52,
>> +               0,  0,  0,  0,  0, 0,  1, 0,  2, 0, 0, 0),
>> +       BANK_DS("C",    GPIOC_0,    GPIOC_7,  53, 60,
>> +               1,  0,  1,  0,  3, 0,  4, 0,  5, 0, 1, 0),
>> +       BANK_DS("A",    GPIOA_0,    GPIOA_15,  61, 76,
>> +               5,  0,  5,  0,  16,  0,  17,  0,  18,  0, 6, 0),
>> +       BANK_DS("X",    GPIOX_0,    GPIOX_19,   77, 96,
>> +               2,  0,  2,  0,  6,  0,  7,  0,  8,  0, 2, 0),
>>  };
>>
>>  static struct meson_bank meson_g12a_aobus_banks[] = {
>> -       /* name  first  last  irq  pullen  pull  dir  out  in  */
>> -       BANK("AO",   GPIOAO_0,  GPIOAO_11,  0, 11,
>> -            3,  0,  2, 0,  0,  0,  4, 0,  1,  0),
>> +       /* name  first  last  irq  pullen  pull  dir  out  in  ds */
>> +       BANK_DS("AO", GPIOAO_0, GPIOAO_11, 0, 11, 3, 0, 2, 0, 0, 0, 4, 0, 1, 0,
>> +               0, 0),
>>         /* GPIOE actually located in the AO bank */
>> -       BANK("E",   GPIOE_0,  GPIOE_2,   97, 99,
>> -            3,  16,  2, 16,  0,  16,  4, 16,  1,  16),
>> +       BANK_DS("E", GPIOE_0, GPIOE_2, 97, 99, 3, 16, 2, 16, 0, 16, 4, 16, 1,
>> +               16, 1, 0),
>>  };
> these definitions are really hard to read, but it's been like this
> even before your patch
>
>>  static struct meson_pmx_bank meson_g12a_periphs_pmx_banks[] = {
>> diff --git a/drivers/pinctrl/meson/pinctrl-meson.c b/drivers/pinctrl/meson/pinctrl-meson.c
>> index 96a4a72708e4..5108e5aa6514 100644
>> --- a/drivers/pinctrl/meson/pinctrl-meson.c
>> +++ b/drivers/pinctrl/meson/pinctrl-meson.c
>> @@ -174,62 +174,106 @@ int meson_pmx_get_groups(struct pinctrl_dev *pcdev, unsigned selector,
>>         return 0;
>>  }
>>
>> -static int meson_pinconf_set(struct pinctrl_dev *pcdev, unsigned int pin,
>> -                            unsigned long *configs, unsigned num_configs)
>> +static int meson_pinconf_set_bias(struct meson_pinctrl *pc, unsigned int pin,
>> +                                 enum pin_config_param conf)
> can you please confirm that I understood the purpose of this correctly:
> I think you introduce this to make setting the bias consistent with
> how you set the drive-strength.
> if so then it would be great to have a separate patch which describes
> that it's only a code-style change and a functional no-op


you  are right, i will separate this changes.


>
> additionally the function arguments are not consistent with
> meson_pinconf_get_drive_strength():
> - here you pass the pinctrl subsystem specific parameters (enum
> pin_config_param conf)
> - in meson_pinconf_get_drive_strength the conversion for pinctrl
> subsystem specific values (pinconf_to_config_argument) is part of
> meson_pinconf_set


for param i'm not sure i understand what you want, if you talk about difference between set_bias and set_drive arg , it's difficult to align it.

if it's about diff between get_bias and get_drive i think i can return drive stength value instead of using an u16 arg input param.


> I'm wondering whether two separate functions
> (meson_pinconf_disable_bias and meson_pinconf_enable_bias) would make
> things easier to read. I haven't tried whether this would really make
> things better, so I'd like to hear your opinion on this Guillaume!


no special opinion on this, if you think it's better for understanding i can separate  set_bias function.


>
> [...]
>> +static int meson_pinconf_set_drive_strength(struct meson_pinctrl *pc,
>> +                                           unsigned int pin, u16 arg)
>>  {
>> -       struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev);
>>         struct meson_bank *bank;
>> -       enum pin_config_param param;
>>         unsigned int reg, bit;
>> -       int i, ret;
>> +       unsigned int ds_val;
>> +       int ret;
>> +
>> +       if (!pc->reg_ds) {
>> +               dev_err(pc->dev, "drive-strength not supported\n");
>> +               return -ENOTSUPP;
> in meson_pinconf_set() we don't complain (with a dev_err) for this case.
> I'm not sure what the best-practice is for the pinctrl subsystem,
> maybe Linus can comment on this
>

this check is to be sure it's possible to set drive stength,

if no register bank is setting in DT but drive-stength properties are setting on pins i need to generate an error

because something is wrong.


>> +       }
>>
>>         ret = meson_get_bank(pc, pin, &bank);
>>         if (ret)
>>                 return ret;
>>
>> +       meson_calc_reg_and_bit(bank, pin, REG_DS, &reg, &bit);
>> +       bit = bit << 1;
>> +
>> +       if (arg <= 500) {
>> +               ds_val = MESON_PINCONF_DRV_500UA;
>> +       } else if (arg <= 2500) {
>> +               ds_val = MESON_PINCONF_DRV_2500UA;
>> +       } else if (arg <= 3000) {
>> +               ds_val = MESON_PINCONF_DRV_3000UA;
>> +       } else if (arg <= 4000) {
>> +               ds_val = MESON_PINCONF_DRV_4000UA;
>> +       } else {
>> +               dev_warn_once(pc->dev,
>> +                             "pin %u: invalid drive-strength : %d , default to 4mA\n",
>> +                             pin, arg);
>> +               ds_val = MESON_PINCONF_DRV_4000UA;
> why not return -EINVAL here? (my assumption is that the pinctrl
> subsystem would like to have -EINVAL instead of drivers doing
> fallbacks if the values are out-of-range, but I'm not 100% sure about
> this)
>
> [...]


i choose to set a default value instead of generating an error,

in this case it's only if you ask a value upper than 4000uA so it's not really a risk to set 4000uA by default.


>> +static int meson_pinconf_get_drive_strength(struct meson_pinctrl *pc,
>> +                                           unsigned int pin, u16 *arg)
>> +{
>> +       struct meson_bank *bank;
>> +       unsigned int reg, bit;
>> +       unsigned int val;
>> +       int ret;
>> +
> do you need to return -ENOTSUPP here if pc->reg_ds is NULL, similar to
> what you already have in meson_pinconf_set_drive_strength()?

depending of linux comment on your feedback on meson_pinconf_set_drive_strength

i will update this part .


>
>
> Regards
> Martin


Regards

Guillaume


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

  reply index

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-04-18 12:47 [PATCH v2 0/4] Add drive-strength in Meson pinctrl driver Guillaume La Roque
2019-04-18 12:47 ` [PATCH v2 1/4] dt-bindings: pinctrl: add a 'drive-strength-uA' property Guillaume La Roque
2019-04-23 11:13   ` Linus Walleij
2019-04-27 19:19   ` Martin Blumenstingl
2019-04-29 19:19   ` Kevin Hilman
2019-04-30 15:12   ` Rob Herring
2019-04-30 15:24     ` guillaume La Roque
2019-04-18 12:47 ` [PATCH v2 2/4] pinctrl: generic: add new 'drive-strength-uA' property support Guillaume La Roque
2019-04-18 12:47 ` [PATCH v2 3/4] dt-bindings: pinctrl: meson: Add drive-strength-uA property Guillaume La Roque
2019-04-27 19:21   ` Martin Blumenstingl
2019-04-30  6:38     ` guillaume La Roque
2019-04-18 12:47 ` [PATCH v2 4/4] pinctrl: meson: add support of drive-strength-uA Guillaume La Roque
2019-04-27 19:44   ` Martin Blumenstingl
2019-04-30  7:20     ` guillaume La Roque [this message]
2019-04-30 20:28       ` Martin Blumenstingl
2019-05-06 13:16         ` guillaume La Roque
2019-04-23 11:13 ` [PATCH v2 0/4] Add drive-strength in Meson pinctrl driver Linus Walleij
2019-04-27 19:46   ` Martin Blumenstingl

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=163fa4df-1017-d230-b264-51ea71236df9@baylibre.com \
    --to=glaroque@baylibre.com \
    --cc=devicetree@vger.kernel.org \
    --cc=khilman@baylibre.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=martin.blumenstingl@googlemail.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Amlogic Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-amlogic/0 linux-amlogic/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-amlogic linux-amlogic/ https://lore.kernel.org/linux-amlogic \
		linux-amlogic@lists.infradead.org linux-amlogic@archiver.kernel.org
	public-inbox-index linux-amlogic


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-amlogic


AGPL code for this site: git clone https://public-inbox.org/ public-inbox