linux-amlogic.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Carlo Caione <ccaione@baylibre.com>
To: robh+dt@kernel.org, mark.rutland@arm.com, khilman@baylibre.com,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-amlogic@lists.infradead.org,
	martin.blumenstingl@googlemail.com, ingrassia@epigenesys.com
Cc: Carlo Caione <ccaione@baylibre.com>
Subject: [PATCH v2 1/2] arm64: dts: meson: Fix IRQ trigger type for macirq
Date: Fri,  7 Dec 2018 10:52:30 +0000	[thread overview]
Message-ID: <20181207105231.25593-2-ccaione@baylibre.com> (raw)
In-Reply-To: <20181207105231.25593-1-ccaione@baylibre.com>

A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.

After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.

The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.

Fixes: feb3cbea0946 ("ARM64: dts: meson-gxbb-odroidc2: fix GbE tx link breakage")
Fixes: 6d28d577510f ("ARM64: dts: meson-axg: fix ethernet stability issue")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
---
 arch/arm64/boot/dts/amlogic/meson-axg-s400.dts      | 1 -
 arch/arm64/boot/dts/amlogic/meson-axg.dtsi          | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gx.dtsi           | 2 +-
 arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 1 -
 arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi   | 1 -
 5 files changed, 2 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
index 18778ada7bd3..4d57363ac536 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
@@ -357,7 +357,6 @@
 		eth_phy0: ethernet-phy@0 {
 			/* Realtek RTL8211F (0x001cc916) */
 			reg = <0>;
-			eee-broken-1000t;
 		};
 	};
 };
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
index df017dbd2e57..b1a42e99cb67 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
@@ -143,7 +143,7 @@
 			compatible = "amlogic,meson-axg-dwmac", "snps,dwmac";
 			reg = <0x0 0xff3f0000 0x0 0x10000
 			       0x0 0xff634540 0x0 0x8>;
-			interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			clocks = <&clkc CLKID_ETH>,
 				 <&clkc CLKID_FCLK_DIV2>,
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
index f1e5cdbade5e..58e6bcaac1d8 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -462,7 +462,7 @@
 			compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
 			reg = <0x0 0xc9410000 0x0 0x10000
 			       0x0 0xc8834540 0x0 0x4>;
-			interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			status = "disabled";
 		};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 54954b314a45..f8d1cedbe600 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -143,7 +143,6 @@
 			interrupt-parent = <&gpio_intc>;
 			/* MAC_INTR on GPIOZ_15 */
 			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
-			eee-broken-1000t;
 		};
 	};
 };
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
index 70325b273bd2..ec09bb5792b7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
@@ -142,7 +142,6 @@
 		eth_phy0: ethernet-phy@0 {
 			/* Realtek RTL8211F (0x001cc916) */
 			reg = <0>;
-			eee-broken-1000t;
 		};
 	};
 };
-- 
2.19.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

  reply	other threads:[~2018-12-07 10:53 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-12-07 10:52 [PATCH v2 0/2] meson: Fix IRQ trigger type Carlo Caione
2018-12-07 10:52 ` Carlo Caione [this message]
2018-12-08  0:20   ` [PATCH v2 1/2] arm64: dts: meson: Fix IRQ trigger type for macirq Kevin Hilman
2018-12-07 10:52 ` [PATCH v2 2/2] arm: " Carlo Caione
2018-12-07 18:51   ` Emiliano Ingrassia
2018-12-08 10:46     ` Carlo Caione
2018-12-12 10:49       ` Emiliano Ingrassia
2018-12-07 22:06   ` Martin Blumenstingl
2018-12-29  0:17   ` Martin Blumenstingl
2019-01-11  0:21     ` Kevin Hilman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181207105231.25593-2-ccaione@baylibre.com \
    --to=ccaione@baylibre.com \
    --cc=devicetree@vger.kernel.org \
    --cc=ingrassia@epigenesys.com \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=mark.rutland@arm.com \
    --cc=martin.blumenstingl@googlemail.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).