[PATCH 0/5] ASoC: meson: add hdmitx glue support

[PATCH 0/5] ASoC: meson: add hdmitx glue support

[Jerome Brunet]

On the Amlogic SoC, there is a glue between the SoC audio outputs and the
input of the embedded Synopsys HDMI controller.

On the g12a, this glue is mostly a couple of muxes to select the i2s and
spdif inputs of the hdmi controller. Each of these inputs may have
different hw_params and fmt which makes our life a little bit more
interesting, especially when switching between to active inputs.

This glue is modeled as codec driver and uses codec-to-codec links to
connect to the Synopsys controller. This allows to use the regular
hdmi-codec driver (used by dw-hdmi i2s).

To avoid glitches while switching input, the trick is to temporarily
force a disconnection of the mux output, which shutdowns the output dai
link. This also ensure that the stream parameters and fmt are updated
when the output is connected back.

Jerome Brunet (5):
  ASoC: meson: axg-card: set link name based on link node name
  ASoC: dapm: allow muxes to force a disconnect
  ASoC: meson: add tohdmitx DT bindings
  ASoC: meson: axg-card: add basic codec-to-codec link support
  ASoC: meson: add g12a tohdmitx control

 .../bindings/sound/amlogic,g12a-tohdmitx.txt  |  55 +++
 .../dt-bindings/sound/meson-g12a-tohdmitx.h   |  13 +
 sound/soc/meson/Kconfig                       |   8 +
 sound/soc/meson/Makefile                      |   2 +
 sound/soc/meson/axg-card.c                    |  31 +-
 sound/soc/meson/g12a-tohdmitx.c               | 413 ++++++++++++++++++
 sound/soc/soc-dapm.c                          |   2 +-
 7 files changed, 518 insertions(+), 6 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
 create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h
 create mode 100644 sound/soc/meson/g12a-tohdmitx.c

-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 1/5] ASoC: meson: axg-card: set link name based on link node name

[Jerome Brunet]

So far the link names of the axg sound card was derived from the cpu name
of the link. Since the dai link must be unique, it works as long as a
device does not provide more than one cpu dai. However, the 'tohdmitx'
does provide 2 dais used as cpu on codec-to-codec links

Instead of cpu name, use the node name of the dai link. DT already enforce
the uniqueness of this name

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 sound/soc/meson/axg-card.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/sound/soc/meson/axg-card.c b/sound/soc/meson/axg-card.c
index aa54d2c612c9..5c8deee8d512 100644
--- a/sound/soc/meson/axg-card.c
+++ b/sound/soc/meson/axg-card.c
@@ -80,10 +80,11 @@ static int axg_card_parse_dai(struct snd_soc_card *card,
 
 static int axg_card_set_link_name(struct snd_soc_card *card,
 				  struct snd_soc_dai_link *link,
+				  struct device_node *node,
 				  const char *prefix)
 {
 	char *name = devm_kasprintf(card->dev, GFP_KERNEL, "%s.%s",
-				    prefix, link->cpu_of_node->full_name);
+				    prefix, node->full_name);
 	if (!name)
 		return -ENOMEM;
 
@@ -474,7 +475,7 @@ static int axg_card_set_be_link(struct snd_soc_card *card,
 		codec++;
 	}
 
-	ret = axg_card_set_link_name(card, link, "be");
+	ret = axg_card_set_link_name(card, link, node, "be");
 	if (ret)
 		dev_err(card->dev, "error setting %pOFn link name\n", np);
 
@@ -483,6 +484,7 @@ static int axg_card_set_be_link(struct snd_soc_card *card,
 
 static int axg_card_set_fe_link(struct snd_soc_card *card,
 				struct snd_soc_dai_link *link,
+				struct device_node *node,
 				bool is_playback)
 {
 	link->dynamic = 1;
@@ -497,7 +499,7 @@ static int axg_card_set_fe_link(struct snd_soc_card *card,
 	else
 		link->dpcm_capture = 1;
 
-	return axg_card_set_link_name(card, link, "fe");
+	return axg_card_set_link_name(card, link, node, "fe");
 }
 
 static int axg_card_cpu_is_capture_fe(struct device_node *np)
@@ -527,9 +529,9 @@ static int axg_card_add_link(struct snd_soc_card *card, struct device_node *np,
 		return ret;
 
 	if (axg_card_cpu_is_playback_fe(dai_link->cpu_of_node))
-		ret = axg_card_set_fe_link(card, dai_link, true);
+		ret = axg_card_set_fe_link(card, dai_link, np, true);
 	else if (axg_card_cpu_is_capture_fe(dai_link->cpu_of_node))
-		ret = axg_card_set_fe_link(card, dai_link, false);
+		ret = axg_card_set_fe_link(card, dai_link, np, false);
 	else
 		ret = axg_card_set_be_link(card, dai_link, np);
 
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Applied "ASoC: meson: axg-card: set link name based on link node name" to the asoc tree

[Mark Brown]

The patch

   ASoC: meson: axg-card: set link name based on link node name

has been applied to the asoc tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From 1b74211011eb064914b8155a77a8aaae61cd27eb Mon Sep 17 00:00:00 2001
From: Jerome Brunet <jbrunet@baylibre.com>
Date: Wed, 15 May 2019 15:18:54 +0200
Subject: [PATCH] ASoC: meson: axg-card: set link name based on link node name

So far the link names of the axg sound card was derived from the cpu name
of the link. Since the dai link must be unique, it works as long as a
device does not provide more than one cpu dai. However, the 'tohdmitx'
does provide 2 dais used as cpu on codec-to-codec links

Instead of cpu name, use the node name of the dai link. DT already enforce
the uniqueness of this name

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 sound/soc/meson/axg-card.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/sound/soc/meson/axg-card.c b/sound/soc/meson/axg-card.c
index aa54d2c612c9..5c8deee8d512 100644
--- a/sound/soc/meson/axg-card.c
+++ b/sound/soc/meson/axg-card.c
@@ -80,10 +80,11 @@ static int axg_card_parse_dai(struct snd_soc_card *card,
 
 static int axg_card_set_link_name(struct snd_soc_card *card,
 				  struct snd_soc_dai_link *link,
+				  struct device_node *node,
 				  const char *prefix)
 {
 	char *name = devm_kasprintf(card->dev, GFP_KERNEL, "%s.%s",
-				    prefix, link->cpu_of_node->full_name);
+				    prefix, node->full_name);
 	if (!name)
 		return -ENOMEM;
 
@@ -474,7 +475,7 @@ static int axg_card_set_be_link(struct snd_soc_card *card,
 		codec++;
 	}
 
-	ret = axg_card_set_link_name(card, link, "be");
+	ret = axg_card_set_link_name(card, link, node, "be");
 	if (ret)
 		dev_err(card->dev, "error setting %pOFn link name\n", np);
 
@@ -483,6 +484,7 @@ static int axg_card_set_be_link(struct snd_soc_card *card,
 
 static int axg_card_set_fe_link(struct snd_soc_card *card,
 				struct snd_soc_dai_link *link,
+				struct device_node *node,
 				bool is_playback)
 {
 	link->dynamic = 1;
@@ -497,7 +499,7 @@ static int axg_card_set_fe_link(struct snd_soc_card *card,
 	else
 		link->dpcm_capture = 1;
 
-	return axg_card_set_link_name(card, link, "fe");
+	return axg_card_set_link_name(card, link, node, "fe");
 }
 
 static int axg_card_cpu_is_capture_fe(struct device_node *np)
@@ -527,9 +529,9 @@ static int axg_card_add_link(struct snd_soc_card *card, struct device_node *np,
 		return ret;
 
 	if (axg_card_cpu_is_playback_fe(dai_link->cpu_of_node))
-		ret = axg_card_set_fe_link(card, dai_link, true);
+		ret = axg_card_set_fe_link(card, dai_link, np, true);
 	else if (axg_card_cpu_is_capture_fe(dai_link->cpu_of_node))
-		ret = axg_card_set_fe_link(card, dai_link, false);
+		ret = axg_card_set_fe_link(card, dai_link, np, false);
 	else
 		ret = axg_card_set_be_link(card, dai_link, np);
 
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 2/5] ASoC: dapm: allow muxes to force a disconnect

[Jerome Brunet]

Let soc_dapm_mux_update_power() accept NULL as 'e' enum.

It makes the code a bit more robust and, more importantly, let the calling
mux force a disconnect of the output path if necessary.

This is useful if the dapm elements following the mux must be off
while updating the mux, to avoid glitches or force a (re)configuration.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 sound/soc/soc-dapm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/sound/soc/soc-dapm.c b/sound/soc/soc-dapm.c
index 81a7a12196ff..a4d6c068b545 100644
--- a/sound/soc/soc-dapm.c
+++ b/sound/soc/soc-dapm.c
@@ -2245,7 +2245,7 @@ static int soc_dapm_mux_update_power(struct snd_soc_card *card,
 	dapm_kcontrol_for_each_path(path, kcontrol) {
 		found = 1;
 		/* we now need to match the string in the enum to the path */
-		if (!(strcmp(path->name, e->texts[mux])))
+		if (e && !(strcmp(path->name, e->texts[mux])))
 			connect = true;
 		else
 			connect = false;
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Applied "ASoC: dapm: allow muxes to force a disconnect" to the asoc tree

[Mark Brown]

The patch

   ASoC: dapm: allow muxes to force a disconnect

has been applied to the asoc tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From c3456a4b2142550944f73a87a8f338074508b249 Mon Sep 17 00:00:00 2001
From: Jerome Brunet <jbrunet@baylibre.com>
Date: Wed, 15 May 2019 15:18:55 +0200
Subject: [PATCH] ASoC: dapm: allow muxes to force a disconnect

Let soc_dapm_mux_update_power() accept NULL as 'e' enum.

It makes the code a bit more robust and, more importantly, let the calling
mux force a disconnect of the output path if necessary.

This is useful if the dapm elements following the mux must be off
while updating the mux, to avoid glitches or force a (re)configuration.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 sound/soc/soc-dapm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/sound/soc/soc-dapm.c b/sound/soc/soc-dapm.c
index 81a7a12196ff..a4d6c068b545 100644
--- a/sound/soc/soc-dapm.c
+++ b/sound/soc/soc-dapm.c
@@ -2245,7 +2245,7 @@ static int soc_dapm_mux_update_power(struct snd_soc_card *card,
 	dapm_kcontrol_for_each_path(path, kcontrol) {
 		found = 1;
 		/* we now need to match the string in the enum to the path */
-		if (!(strcmp(path->name, e->texts[mux])))
+		if (e && !(strcmp(path->name, e->texts[mux])))
 			connect = true;
 		else
 			connect = false;
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 3/5] ASoC: meson: add tohdmitx DT bindings

[Jerome Brunet]

Add the bindings and the related documentation for the audio hdmitx
control glue of the Amlogic g12a SoC family

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 .../bindings/sound/amlogic,g12a-tohdmitx.txt  | 55 +++++++++++++++++++
 .../dt-bindings/sound/meson-g12a-tohdmitx.h   | 13 +++++
 2 files changed, 68 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
 create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h

diff --git a/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt b/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
new file mode 100644
index 000000000000..aa6c35570d31
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
@@ -0,0 +1,55 @@
+* Amlogic HDMI Tx control glue
+
+Required properties:
+- compatible: "amlogic,g12a-tohdmitx"
+- reg: physical base address of the controller and length of memory
+       mapped region.
+- #sound-dai-cells: should be 1.
+
+Example on the S905X2 SoC:
+
+tohdmitx: audio-controller@744 {
+	compatible = "amlogic,g12a-tohdmitx";
+	reg = <0x0 0x744 0x0 0x4>;
+	#sound-dai-cells = <1>;
+};
+
+Example of an 'amlogic,axg-sound-card':
+
+sound {
+	compatible = "amlogic,axg-sound-card";
+
+[...]
+
+	dai-link-x {
+		sound-dai = <&tdmif_a>;
+		dai-format = "i2s";
+		dai-tdm-slot-tx-mask-0 = <1 1>;
+
+		codec-0 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
+		};
+
+		codec-1 {
+			sound-dai = <&external_dac>;
+		};
+	};
+
+	dai-link-y {
+		sound-dai = <&tdmif_c>;
+		dai-format = "i2s";
+		dai-tdm-slot-tx-mask-0 = <1 1>;
+
+		codec {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_IN_C>;
+		};
+	};
+
+	dai-link-z {
+		sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+		codec {
+			sound-dai = <&hdmi_tx>;
+		};
+	};
+};
diff --git a/include/dt-bindings/sound/meson-g12a-tohdmitx.h b/include/dt-bindings/sound/meson-g12a-tohdmitx.h
new file mode 100644
index 000000000000..c5e1f48d30d0
--- /dev/null
+++ b/include/dt-bindings/sound/meson-g12a-tohdmitx.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DT_MESON_G12A_TOHDMITX_H
+#define __DT_MESON_G12A_TOHDMITX_H
+
+#define TOHDMITX_I2S_IN_A	0
+#define TOHDMITX_I2S_IN_B	1
+#define TOHDMITX_I2S_IN_C	2
+#define TOHDMITX_I2S_OUT	3
+#define TOHDMITX_SPDIF_IN_A	4
+#define TOHDMITX_SPDIF_IN_B	5
+#define TOHDMITX_SPDIF_OUT	6
+
+#endif /* __DT_MESON_G12A_TOHDMITX_H */
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Applied "ASoC: meson: add tohdmitx DT bindings" to the asoc tree

[Mark Brown]

The patch

   ASoC: meson: add tohdmitx DT bindings

has been applied to the asoc tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From e35f5ad6a965de5d301ca5957a1c48c53fe366fb Mon Sep 17 00:00:00 2001
From: Jerome Brunet <jbrunet@baylibre.com>
Date: Wed, 15 May 2019 15:18:56 +0200
Subject: [PATCH] ASoC: meson: add tohdmitx DT bindings

Add the bindings and the related documentation for the audio hdmitx
control glue of the Amlogic g12a SoC family

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 .../bindings/sound/amlogic,g12a-tohdmitx.txt  | 55 +++++++++++++++++++
 .../dt-bindings/sound/meson-g12a-tohdmitx.h   | 13 +++++
 2 files changed, 68 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
 create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h

diff --git a/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt b/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
new file mode 100644
index 000000000000..aa6c35570d31
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
@@ -0,0 +1,55 @@
+* Amlogic HDMI Tx control glue
+
+Required properties:
+- compatible: "amlogic,g12a-tohdmitx"
+- reg: physical base address of the controller and length of memory
+       mapped region.
+- #sound-dai-cells: should be 1.
+
+Example on the S905X2 SoC:
+
+tohdmitx: audio-controller@744 {
+	compatible = "amlogic,g12a-tohdmitx";
+	reg = <0x0 0x744 0x0 0x4>;
+	#sound-dai-cells = <1>;
+};
+
+Example of an 'amlogic,axg-sound-card':
+
+sound {
+	compatible = "amlogic,axg-sound-card";
+
+[...]
+
+	dai-link-x {
+		sound-dai = <&tdmif_a>;
+		dai-format = "i2s";
+		dai-tdm-slot-tx-mask-0 = <1 1>;
+
+		codec-0 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
+		};
+
+		codec-1 {
+			sound-dai = <&external_dac>;
+		};
+	};
+
+	dai-link-y {
+		sound-dai = <&tdmif_c>;
+		dai-format = "i2s";
+		dai-tdm-slot-tx-mask-0 = <1 1>;
+
+		codec {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_IN_C>;
+		};
+	};
+
+	dai-link-z {
+		sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+		codec {
+			sound-dai = <&hdmi_tx>;
+		};
+	};
+};
diff --git a/include/dt-bindings/sound/meson-g12a-tohdmitx.h b/include/dt-bindings/sound/meson-g12a-tohdmitx.h
new file mode 100644
index 000000000000..c5e1f48d30d0
--- /dev/null
+++ b/include/dt-bindings/sound/meson-g12a-tohdmitx.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DT_MESON_G12A_TOHDMITX_H
+#define __DT_MESON_G12A_TOHDMITX_H
+
+#define TOHDMITX_I2S_IN_A	0
+#define TOHDMITX_I2S_IN_B	1
+#define TOHDMITX_I2S_IN_C	2
+#define TOHDMITX_I2S_OUT	3
+#define TOHDMITX_SPDIF_IN_A	4
+#define TOHDMITX_SPDIF_IN_B	5
+#define TOHDMITX_SPDIF_OUT	6
+
+#endif /* __DT_MESON_G12A_TOHDMITX_H */
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 4/5] ASoC: meson: axg-card: add basic codec-to-codec link support

[Jerome Brunet]

Add basic support for codec-to-codec link in the axg sound card.
The cpu side of these links is expected to properly set the hw_params
and format of the link.

ATM, only the tohdmitx glue is supported but others (like the
internal DAC glue) should follow.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 sound/soc/meson/axg-card.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/sound/soc/meson/axg-card.c b/sound/soc/meson/axg-card.c
index 5c8deee8d512..db0a7fc18928 100644
--- a/sound/soc/meson/axg-card.c
+++ b/sound/soc/meson/axg-card.c
@@ -29,6 +29,18 @@ struct axg_dai_link_tdm_data {
 	struct axg_dai_link_tdm_mask *codec_masks;
 };
 
+/*
+ * Base params for the codec to codec links
+ * Those will be over-written by the CPU side of the link
+ */
+static const struct snd_soc_pcm_stream codec_params = {
+	.formats = SNDRV_PCM_FMTBIT_S24_LE,
+	.rate_min = 5525,
+	.rate_max = 192000,
+	.channels_min = 1,
+	.channels_max = 8,
+};
+
 #define PREFIX "amlogic,"
 
 static int axg_card_reallocate_links(struct axg_card *priv,
@@ -517,6 +529,11 @@ static int axg_card_cpu_is_tdm_iface(struct device_node *np)
 	return of_device_is_compatible(np, PREFIX "axg-tdm-iface");
 }
 
+static int axg_card_cpu_is_codec(struct device_node *np)
+{
+	return of_device_is_compatible(np, PREFIX "g12a-tohdmitx");
+}
+
 static int axg_card_add_link(struct snd_soc_card *card, struct device_node *np,
 			     int *index)
 {
@@ -540,6 +557,8 @@ static int axg_card_add_link(struct snd_soc_card *card, struct device_node *np,
 
 	if (axg_card_cpu_is_tdm_iface(dai_link->cpu_of_node))
 		ret = axg_card_parse_tdm(card, np, index);
+	else if (axg_card_cpu_is_codec(dai_link->cpu_of_node))
+		dai_link->params = &codec_params;
 
 	return ret;
 }
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Applied "ASoC: meson: axg-card: add basic codec-to-codec link support" to the asoc tree

[Mark Brown]

The patch

   ASoC: meson: axg-card: add basic codec-to-codec link support

has been applied to the asoc tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From 0a8f1117a6803398d361e7bd76fef59c636f143b Mon Sep 17 00:00:00 2001
From: Jerome Brunet <jbrunet@baylibre.com>
Date: Wed, 15 May 2019 15:18:57 +0200
Subject: [PATCH] ASoC: meson: axg-card: add basic codec-to-codec link support

Add basic support for codec-to-codec link in the axg sound card.
The cpu side of these links is expected to properly set the hw_params
and format of the link.

ATM, only the tohdmitx glue is supported but others (like the
internal DAC glue) should follow.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 sound/soc/meson/axg-card.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/sound/soc/meson/axg-card.c b/sound/soc/meson/axg-card.c
index 5c8deee8d512..db0a7fc18928 100644
--- a/sound/soc/meson/axg-card.c
+++ b/sound/soc/meson/axg-card.c
@@ -29,6 +29,18 @@ struct axg_dai_link_tdm_data {
 	struct axg_dai_link_tdm_mask *codec_masks;
 };
 
+/*
+ * Base params for the codec to codec links
+ * Those will be over-written by the CPU side of the link
+ */
+static const struct snd_soc_pcm_stream codec_params = {
+	.formats = SNDRV_PCM_FMTBIT_S24_LE,
+	.rate_min = 5525,
+	.rate_max = 192000,
+	.channels_min = 1,
+	.channels_max = 8,
+};
+
 #define PREFIX "amlogic,"
 
 static int axg_card_reallocate_links(struct axg_card *priv,
@@ -517,6 +529,11 @@ static int axg_card_cpu_is_tdm_iface(struct device_node *np)
 	return of_device_is_compatible(np, PREFIX "axg-tdm-iface");
 }
 
+static int axg_card_cpu_is_codec(struct device_node *np)
+{
+	return of_device_is_compatible(np, PREFIX "g12a-tohdmitx");
+}
+
 static int axg_card_add_link(struct snd_soc_card *card, struct device_node *np,
 			     int *index)
 {
@@ -540,6 +557,8 @@ static int axg_card_add_link(struct snd_soc_card *card, struct device_node *np,
 
 	if (axg_card_cpu_is_tdm_iface(dai_link->cpu_of_node))
 		ret = axg_card_parse_tdm(card, np, index);
+	else if (axg_card_cpu_is_codec(dai_link->cpu_of_node))
+		dai_link->params = &codec_params;
 
 	return ret;
 }
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 5/5] ASoC: meson: add g12a tohdmitx control

[Jerome Brunet]

Add support for the hdmitx control glue of the Amlogic g12a SoC family.
This glue links the 3 TDM and 2 SPDIF output interfaces of the SoC to
the related inputs of the Synopsys HDMI controller found in these SoCs.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 sound/soc/meson/Kconfig         |   8 +
 sound/soc/meson/Makefile        |   2 +
 sound/soc/meson/g12a-tohdmitx.c | 413 ++++++++++++++++++++++++++++++++
 3 files changed, 423 insertions(+)
 create mode 100644 sound/soc/meson/g12a-tohdmitx.c

diff --git a/sound/soc/meson/Kconfig b/sound/soc/meson/Kconfig
index 8779fe23671d..4e5b4d4f3531 100644
--- a/sound/soc/meson/Kconfig
+++ b/sound/soc/meson/Kconfig
@@ -56,6 +56,7 @@ config SND_MESON_AXG_SOUND_CARD
 	imply SND_MESON_AXG_SPDIFOUT
 	imply SND_MESON_AXG_SPDIFIN
 	imply SND_MESON_AXG_PDM
+	imply SND_MESON_G12A_TOHDMITX if DRM_MESON_DW_HDMI
 	help
 	  Select Y or M to add support for the AXG SoC sound card
 
@@ -82,4 +83,11 @@ config SND_MESON_AXG_PDM
 	help
 	  Select Y or M to add support for PDM input embedded
 	  in the Amlogic AXG SoC family
+
+config SND_MESON_G12A_TOHDMITX
+	tristate "Amlogic G12A To HDMI TX Control Support"
+	imply SND_SOC_HDMI_CODEC
+	help
+	  Select Y or M to add support for HDMI audio on the g12a SoC
+	  family
 endmenu
diff --git a/sound/soc/meson/Makefile b/sound/soc/meson/Makefile
index b45dfb9e2f88..1a8b1470ed84 100644
--- a/sound/soc/meson/Makefile
+++ b/sound/soc/meson/Makefile
@@ -11,6 +11,7 @@ snd-soc-meson-axg-sound-card-objs := axg-card.o
 snd-soc-meson-axg-spdifin-objs := axg-spdifin.o
 snd-soc-meson-axg-spdifout-objs := axg-spdifout.o
 snd-soc-meson-axg-pdm-objs := axg-pdm.o
+snd-soc-meson-g12a-tohdmitx-objs := g12a-tohdmitx.o
 
 obj-$(CONFIG_SND_MESON_AXG_FIFO) += snd-soc-meson-axg-fifo.o
 obj-$(CONFIG_SND_MESON_AXG_FRDDR) += snd-soc-meson-axg-frddr.o
@@ -23,3 +24,4 @@ obj-$(CONFIG_SND_MESON_AXG_SOUND_CARD) += snd-soc-meson-axg-sound-card.o
 obj-$(CONFIG_SND_MESON_AXG_SPDIFIN) += snd-soc-meson-axg-spdifin.o
 obj-$(CONFIG_SND_MESON_AXG_SPDIFOUT) += snd-soc-meson-axg-spdifout.o
 obj-$(CONFIG_SND_MESON_AXG_PDM) += snd-soc-meson-axg-pdm.o
+obj-$(CONFIG_SND_MESON_G12A_TOHDMITX) += snd-soc-meson-g12a-tohdmitx.o
diff --git a/sound/soc/meson/g12a-tohdmitx.c b/sound/soc/meson/g12a-tohdmitx.c
new file mode 100644
index 000000000000..707ccb192e4c
--- /dev/null
+++ b/sound/soc/meson/g12a-tohdmitx.c
@@ -0,0 +1,413 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (c) 2019 BayLibre, SAS.
+// Author: Jerome Brunet <jbrunet@baylibre.com>
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <sound/pcm_params.h>
+#include <linux/regmap.h>
+#include <sound/soc.h>
+#include <sound/soc-dai.h>
+
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+#define G12A_TOHDMITX_DRV_NAME "g12a-tohdmitx"
+
+#define TOHDMITX_CTRL0			0x0
+#define  CTRL0_ENABLE_SHIFT		31
+#define  CTRL0_I2S_DAT_SEL		GENMASK(13, 12)
+#define  CTRL0_I2S_LRCLK_SEL		GENMASK(9, 8)
+#define  CTRL0_I2S_BLK_CAP_INV		BIT(7)
+#define  CTRL0_I2S_BCLK_O_INV		BIT(6)
+#define  CTRL0_I2S_BCLK_SEL		GENMASK(5, 4)
+#define  CTRL0_SPDIF_CLK_CAP_INV	BIT(3)
+#define  CTRL0_SPDIF_CLK_O_INV		BIT(2)
+#define  CTRL0_SPDIF_SEL		BIT(1)
+#define  CTRL0_SPDIF_CLK_SEL		BIT(0)
+
+struct g12a_tohdmitx_input {
+	struct snd_pcm_hw_params params;
+	unsigned int fmt;
+};
+
+static struct snd_soc_dapm_widget *
+g12a_tohdmitx_get_input(struct snd_soc_dapm_widget *w)
+{
+	struct snd_soc_dapm_path *p = NULL;
+	struct snd_soc_dapm_widget *in;
+
+	snd_soc_dapm_widget_for_each_source_path(w, p) {
+		if (!p->connect)
+			continue;
+
+		/* Check that we still are in the same component */
+		if (snd_soc_dapm_to_component(w->dapm) !=
+		    snd_soc_dapm_to_component(p->source->dapm))
+			continue;
+
+		if (p->source->id == snd_soc_dapm_dai_in)
+			return p->source;
+
+		in = g12a_tohdmitx_get_input(p->source);
+		if (in)
+			return in;
+	}
+
+	return NULL;
+}
+
+static struct g12a_tohdmitx_input *
+g12a_tohdmitx_get_input_data(struct snd_soc_dapm_widget *w)
+{
+	struct snd_soc_dapm_widget *in =
+		g12a_tohdmitx_get_input(w);
+	struct snd_soc_dai *dai;
+
+	if (WARN_ON(!in))
+		return NULL;
+
+	dai = in->priv;
+
+	return dai->playback_dma_data;
+}
+
+static const char * const g12a_tohdmitx_i2s_mux_texts[] = {
+	"I2S A", "I2S B", "I2S C",
+};
+
+static SOC_ENUM_SINGLE_EXT_DECL(g12a_tohdmitx_i2s_mux_enum,
+				g12a_tohdmitx_i2s_mux_texts);
+
+static int g12a_tohdmitx_get_input_val(struct snd_soc_component *component,
+				       unsigned int mask)
+{
+	unsigned int val;
+
+	snd_soc_component_read(component, TOHDMITX_CTRL0, &val);
+	return (val & mask) >> __ffs(mask);
+}
+
+static int g12a_tohdmitx_i2s_mux_get_enum(struct snd_kcontrol *kcontrol,
+					  struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+
+	ucontrol->value.enumerated.item[0] =
+		g12a_tohdmitx_get_input_val(component, CTRL0_I2S_DAT_SEL);
+
+	return 0;
+}
+
+static int g12a_tohdmitx_i2s_mux_put_enum(struct snd_kcontrol *kcontrol,
+					  struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+	struct snd_soc_dapm_context *dapm =
+		snd_soc_dapm_kcontrol_dapm(kcontrol);
+	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
+	unsigned int mux = ucontrol->value.enumerated.item[0];
+	unsigned int val = g12a_tohdmitx_get_input_val(component,
+						       CTRL0_I2S_DAT_SEL);
+
+	/* Force disconnect of the mux while updating */
+	if (val != mux)
+		snd_soc_dapm_mux_update_power(dapm, kcontrol, 0, NULL, NULL);
+
+	snd_soc_component_update_bits(component, TOHDMITX_CTRL0,
+				      CTRL0_I2S_DAT_SEL |
+				      CTRL0_I2S_LRCLK_SEL |
+				      CTRL0_I2S_BCLK_SEL,
+				      FIELD_PREP(CTRL0_I2S_DAT_SEL, mux) |
+				      FIELD_PREP(CTRL0_I2S_LRCLK_SEL, mux) |
+				      FIELD_PREP(CTRL0_I2S_BCLK_SEL, mux));
+
+	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
+
+	return 0;
+}
+
+static const struct snd_kcontrol_new g12a_tohdmitx_i2s_mux =
+	SOC_DAPM_ENUM_EXT("I2S Source", g12a_tohdmitx_i2s_mux_enum,
+			  g12a_tohdmitx_i2s_mux_get_enum,
+			  g12a_tohdmitx_i2s_mux_put_enum);
+
+static const char * const g12a_tohdmitx_spdif_mux_texts[] = {
+	"SPDIF A", "SPDIF B",
+};
+
+static SOC_ENUM_SINGLE_EXT_DECL(g12a_tohdmitx_spdif_mux_enum,
+				g12a_tohdmitx_spdif_mux_texts);
+
+static int g12a_tohdmitx_spdif_mux_get_enum(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+
+	ucontrol->value.enumerated.item[0] =
+		g12a_tohdmitx_get_input_val(component, CTRL0_SPDIF_SEL);
+
+	return 0;
+}
+
+static int g12a_tohdmitx_spdif_mux_put_enum(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+	struct snd_soc_dapm_context *dapm =
+		snd_soc_dapm_kcontrol_dapm(kcontrol);
+	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
+	unsigned int mux = ucontrol->value.enumerated.item[0];
+	unsigned int val = g12a_tohdmitx_get_input_val(component,
+						       CTRL0_SPDIF_SEL);
+
+	/* Force disconnect of the mux while updating */
+	if (val != mux)
+		snd_soc_dapm_mux_update_power(dapm, kcontrol, 0, NULL, NULL);
+
+	snd_soc_component_update_bits(component, TOHDMITX_CTRL0,
+				      CTRL0_SPDIF_SEL |
+				      CTRL0_SPDIF_CLK_SEL,
+				      FIELD_PREP(CTRL0_SPDIF_SEL, mux) |
+				      FIELD_PREP(CTRL0_SPDIF_CLK_SEL, mux));
+
+	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
+
+	return 0;
+}
+
+static const struct snd_kcontrol_new g12a_tohdmitx_spdif_mux =
+	SOC_DAPM_ENUM_EXT("SPDIF Source", g12a_tohdmitx_spdif_mux_enum,
+			  g12a_tohdmitx_spdif_mux_get_enum,
+			  g12a_tohdmitx_spdif_mux_put_enum);
+
+static const struct snd_kcontrol_new g12a_tohdmitx_out_enable =
+	SOC_DAPM_SINGLE_AUTODISABLE("Switch", TOHDMITX_CTRL0,
+				    CTRL0_ENABLE_SHIFT, 1, 0);
+
+static const struct snd_soc_dapm_widget g12a_tohdmitx_widgets[] = {
+	SND_SOC_DAPM_MUX("I2S SRC", SND_SOC_NOPM, 0, 0,
+			 &g12a_tohdmitx_i2s_mux),
+	SND_SOC_DAPM_SWITCH("I2S OUT EN", SND_SOC_NOPM, 0, 0,
+			    &g12a_tohdmitx_out_enable),
+	SND_SOC_DAPM_MUX("SPDIF SRC", SND_SOC_NOPM, 0, 0,
+			 &g12a_tohdmitx_spdif_mux),
+	SND_SOC_DAPM_SWITCH("SPDIF OUT EN", SND_SOC_NOPM, 0, 0,
+			    &g12a_tohdmitx_out_enable),
+};
+
+static int g12a_tohdmitx_input_probe(struct snd_soc_dai *dai)
+{
+	struct g12a_tohdmitx_input *data;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	dai->playback_dma_data = data;
+	return 0;
+}
+
+static int g12a_tohdmitx_input_remove(struct snd_soc_dai *dai)
+{
+	kfree(dai->playback_dma_data);
+	return 0;
+}
+
+static int g12a_tohdmitx_input_hw_params(struct snd_pcm_substream *substream,
+					 struct snd_pcm_hw_params *params,
+					 struct snd_soc_dai *dai)
+{
+	struct g12a_tohdmitx_input *data = dai->playback_dma_data;
+
+	/* Save the stream params for the downstream link */
+	memcpy(&data->params, params, sizeof(*params));
+
+	return 0;
+}
+
+static int g12a_tohdmitx_output_hw_params(struct snd_pcm_substream *substream,
+					  struct snd_pcm_hw_params *params,
+					  struct snd_soc_dai *dai)
+{
+	struct g12a_tohdmitx_input *in_data =
+		g12a_tohdmitx_get_input_data(dai->capture_widget);
+
+	if (!in_data)
+		return -ENODEV;
+
+	memcpy(params, &in_data->params, sizeof(*params));
+
+	return 0;
+}
+
+static int g12a_tohdmitx_input_set_fmt(struct snd_soc_dai *dai,
+				       unsigned int fmt)
+{
+	struct g12a_tohdmitx_input *data = dai->playback_dma_data;
+
+	/* Save the source stream format for the downstream link */
+	data->fmt = fmt;
+	return 0;
+}
+
+static int g12a_tohdmitx_output_startup(struct snd_pcm_substream *substream,
+					struct snd_soc_dai *dai)
+{
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct g12a_tohdmitx_input *in_data =
+		g12a_tohdmitx_get_input_data(dai->capture_widget);
+
+	if (!in_data)
+		return -ENODEV;
+
+	if (!in_data->fmt)
+		return 0;
+
+	return snd_soc_runtime_set_dai_fmt(rtd, in_data->fmt);
+}
+
+static const struct snd_soc_dai_ops g12a_tohdmitx_input_ops = {
+	.hw_params	= g12a_tohdmitx_input_hw_params,
+	.set_fmt	= g12a_tohdmitx_input_set_fmt,
+};
+
+static const struct snd_soc_dai_ops g12a_tohdmitx_output_ops = {
+	.hw_params	= g12a_tohdmitx_output_hw_params,
+	.startup	= g12a_tohdmitx_output_startup,
+};
+
+#define TOHDMITX_SPDIF_FORMATS					\
+	(SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |	\
+	 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE)
+
+#define TOHDMITX_I2S_FORMATS					\
+	(SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |	\
+	 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE |	\
+	 SNDRV_PCM_FMTBIT_S32_LE)
+
+#define TOHDMITX_STREAM(xname, xsuffix, xfmt, xchmax)		\
+{								\
+	.stream_name	= xname " " xsuffix,			\
+	.channels_min	= 1,					\
+	.channels_max	= (xchmax),				\
+	.rate_min       = 8000,					\
+	.rate_max	= 192000,				\
+	.formats	= (xfmt),				\
+}
+
+#define TOHDMITX_IN(xname, xid, xfmt, xchmax) {				\
+	.name = xname,							\
+	.id = (xid),							\
+	.playback = TOHDMITX_STREAM(xname, "Playback", xfmt, xchmax),	\
+	.ops = &g12a_tohdmitx_input_ops,				\
+	.probe = g12a_tohdmitx_input_probe,				\
+	.remove = g12a_tohdmitx_input_remove,				\
+}
+
+#define TOHDMITX_OUT(xname, xid, xfmt, xchmax) {			\
+	.name = xname,							\
+	.id = (xid),							\
+	.capture = TOHDMITX_STREAM(xname, "Capture", xfmt, xchmax),	\
+	.ops = &g12a_tohdmitx_output_ops,				\
+}
+
+static struct snd_soc_dai_driver g12a_tohdmitx_dai_drv[] = {
+	TOHDMITX_IN("I2S IN A", TOHDMITX_I2S_IN_A,
+		    TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_IN("I2S IN B", TOHDMITX_I2S_IN_B,
+		    TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_IN("I2S IN C", TOHDMITX_I2S_IN_C,
+		    TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_OUT("I2S OUT", TOHDMITX_I2S_OUT,
+		     TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_IN("SPDIF IN A", TOHDMITX_SPDIF_IN_A,
+		    TOHDMITX_SPDIF_FORMATS, 2),
+	TOHDMITX_IN("SPDIF IN B", TOHDMITX_SPDIF_IN_B,
+		    TOHDMITX_SPDIF_FORMATS, 2),
+	TOHDMITX_OUT("SPDIF OUT", TOHDMITX_SPDIF_OUT,
+		     TOHDMITX_SPDIF_FORMATS, 2),
+};
+
+static int g12a_tohdmi_component_probe(struct snd_soc_component *c)
+{
+	/* Initialize the static clock parameters */
+	return snd_soc_component_write(c, TOHDMITX_CTRL0,
+		     CTRL0_I2S_BLK_CAP_INV | CTRL0_SPDIF_CLK_CAP_INV);
+}
+
+static const struct snd_soc_dapm_route g12a_tohdmitx_routes[] = {
+	{ "I2S SRC", "I2S A", "I2S IN A Playback" },
+	{ "I2S SRC", "I2S B", "I2S IN B Playback" },
+	{ "I2S SRC", "I2S C", "I2S IN C Playback" },
+	{ "I2S OUT EN", "Switch", "I2S SRC" },
+	{ "I2S OUT Capture", NULL, "I2S OUT EN" },
+	{ "SPDIF SRC", "SPDIF A", "SPDIF IN A Playback" },
+	{ "SPDIF SRC", "SPDIF B", "SPDIF IN B Playback" },
+	{ "SPDIF OUT EN", "Switch", "SPDIF SRC" },
+	{ "SPDIF OUT Capture", NULL, "SPDIF OUT EN" },
+};
+
+static const struct snd_soc_component_driver g12a_tohdmitx_component_drv = {
+	.probe			= g12a_tohdmi_component_probe,
+	.dapm_widgets		= g12a_tohdmitx_widgets,
+	.num_dapm_widgets	= ARRAY_SIZE(g12a_tohdmitx_widgets),
+	.dapm_routes		= g12a_tohdmitx_routes,
+	.num_dapm_routes	= ARRAY_SIZE(g12a_tohdmitx_routes),
+	.endianness		= 1,
+	.non_legacy_dai_naming	= 1,
+};
+
+static const struct regmap_config g12a_tohdmitx_regmap_cfg = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+};
+
+static const struct of_device_id g12a_tohdmitx_of_match[] = {
+	{ .compatible = "amlogic,g12a-tohdmitx", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, g12a_tohdmitx_of_match);
+
+static int g12a_tohdmitx_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	void __iomem *regs;
+	struct regmap *map;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(regs))
+		return PTR_ERR(regs);
+
+	map = devm_regmap_init_mmio(dev, regs, &g12a_tohdmitx_regmap_cfg);
+	if (IS_ERR(map)) {
+		dev_err(dev, "failed to init regmap: %ld\n",
+			PTR_ERR(map));
+		return PTR_ERR(map);
+	}
+
+	return devm_snd_soc_register_component(dev,
+			&g12a_tohdmitx_component_drv, g12a_tohdmitx_dai_drv,
+			ARRAY_SIZE(g12a_tohdmitx_dai_drv));
+}
+
+static struct platform_driver g12a_tohdmitx_pdrv = {
+	.driver = {
+		.name = G12A_TOHDMITX_DRV_NAME,
+		.of_match_table = g12a_tohdmitx_of_match,
+	},
+	.probe = g12a_tohdmitx_probe,
+};
+module_platform_driver(g12a_tohdmitx_pdrv);
+
+MODULE_AUTHOR("Jerome Brunet <jbrunet@baylibre.com>");
+MODULE_DESCRIPTION("Amlogic G12a To HDMI Tx Control Codec Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Applied "ASoC: meson: add g12a tohdmitx control" to the asoc tree

[Mark Brown]

The patch

   ASoC: meson: add g12a tohdmitx control

has been applied to the asoc tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From c8609f3870f7078fc7922eb816ed4908a9bd44f3 Mon Sep 17 00:00:00 2001
From: Jerome Brunet <jbrunet@baylibre.com>
Date: Wed, 15 May 2019 15:18:58 +0200
Subject: [PATCH] ASoC: meson: add g12a tohdmitx control

Add support for the hdmitx control glue of the Amlogic g12a SoC family.
This glue links the 3 TDM and 2 SPDIF output interfaces of the SoC to
the related inputs of the Synopsys HDMI controller found in these SoCs.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 sound/soc/meson/Kconfig         |   8 +
 sound/soc/meson/Makefile        |   2 +
 sound/soc/meson/g12a-tohdmitx.c | 413 ++++++++++++++++++++++++++++++++
 3 files changed, 423 insertions(+)
 create mode 100644 sound/soc/meson/g12a-tohdmitx.c

diff --git a/sound/soc/meson/Kconfig b/sound/soc/meson/Kconfig
index 8779fe23671d..4e5b4d4f3531 100644
--- a/sound/soc/meson/Kconfig
+++ b/sound/soc/meson/Kconfig
@@ -56,6 +56,7 @@ config SND_MESON_AXG_SOUND_CARD
 	imply SND_MESON_AXG_SPDIFOUT
 	imply SND_MESON_AXG_SPDIFIN
 	imply SND_MESON_AXG_PDM
+	imply SND_MESON_G12A_TOHDMITX if DRM_MESON_DW_HDMI
 	help
 	  Select Y or M to add support for the AXG SoC sound card
 
@@ -82,4 +83,11 @@ config SND_MESON_AXG_PDM
 	help
 	  Select Y or M to add support for PDM input embedded
 	  in the Amlogic AXG SoC family
+
+config SND_MESON_G12A_TOHDMITX
+	tristate "Amlogic G12A To HDMI TX Control Support"
+	imply SND_SOC_HDMI_CODEC
+	help
+	  Select Y or M to add support for HDMI audio on the g12a SoC
+	  family
 endmenu
diff --git a/sound/soc/meson/Makefile b/sound/soc/meson/Makefile
index b45dfb9e2f88..1a8b1470ed84 100644
--- a/sound/soc/meson/Makefile
+++ b/sound/soc/meson/Makefile
@@ -11,6 +11,7 @@ snd-soc-meson-axg-sound-card-objs := axg-card.o
 snd-soc-meson-axg-spdifin-objs := axg-spdifin.o
 snd-soc-meson-axg-spdifout-objs := axg-spdifout.o
 snd-soc-meson-axg-pdm-objs := axg-pdm.o
+snd-soc-meson-g12a-tohdmitx-objs := g12a-tohdmitx.o
 
 obj-$(CONFIG_SND_MESON_AXG_FIFO) += snd-soc-meson-axg-fifo.o
 obj-$(CONFIG_SND_MESON_AXG_FRDDR) += snd-soc-meson-axg-frddr.o
@@ -23,3 +24,4 @@ obj-$(CONFIG_SND_MESON_AXG_SOUND_CARD) += snd-soc-meson-axg-sound-card.o
 obj-$(CONFIG_SND_MESON_AXG_SPDIFIN) += snd-soc-meson-axg-spdifin.o
 obj-$(CONFIG_SND_MESON_AXG_SPDIFOUT) += snd-soc-meson-axg-spdifout.o
 obj-$(CONFIG_SND_MESON_AXG_PDM) += snd-soc-meson-axg-pdm.o
+obj-$(CONFIG_SND_MESON_G12A_TOHDMITX) += snd-soc-meson-g12a-tohdmitx.o
diff --git a/sound/soc/meson/g12a-tohdmitx.c b/sound/soc/meson/g12a-tohdmitx.c
new file mode 100644
index 000000000000..707ccb192e4c
--- /dev/null
+++ b/sound/soc/meson/g12a-tohdmitx.c
@@ -0,0 +1,413 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (c) 2019 BayLibre, SAS.
+// Author: Jerome Brunet <jbrunet@baylibre.com>
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <sound/pcm_params.h>
+#include <linux/regmap.h>
+#include <sound/soc.h>
+#include <sound/soc-dai.h>
+
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+#define G12A_TOHDMITX_DRV_NAME "g12a-tohdmitx"
+
+#define TOHDMITX_CTRL0			0x0
+#define  CTRL0_ENABLE_SHIFT		31
+#define  CTRL0_I2S_DAT_SEL		GENMASK(13, 12)
+#define  CTRL0_I2S_LRCLK_SEL		GENMASK(9, 8)
+#define  CTRL0_I2S_BLK_CAP_INV		BIT(7)
+#define  CTRL0_I2S_BCLK_O_INV		BIT(6)
+#define  CTRL0_I2S_BCLK_SEL		GENMASK(5, 4)
+#define  CTRL0_SPDIF_CLK_CAP_INV	BIT(3)
+#define  CTRL0_SPDIF_CLK_O_INV		BIT(2)
+#define  CTRL0_SPDIF_SEL		BIT(1)
+#define  CTRL0_SPDIF_CLK_SEL		BIT(0)
+
+struct g12a_tohdmitx_input {
+	struct snd_pcm_hw_params params;
+	unsigned int fmt;
+};
+
+static struct snd_soc_dapm_widget *
+g12a_tohdmitx_get_input(struct snd_soc_dapm_widget *w)
+{
+	struct snd_soc_dapm_path *p = NULL;
+	struct snd_soc_dapm_widget *in;
+
+	snd_soc_dapm_widget_for_each_source_path(w, p) {
+		if (!p->connect)
+			continue;
+
+		/* Check that we still are in the same component */
+		if (snd_soc_dapm_to_component(w->dapm) !=
+		    snd_soc_dapm_to_component(p->source->dapm))
+			continue;
+
+		if (p->source->id == snd_soc_dapm_dai_in)
+			return p->source;
+
+		in = g12a_tohdmitx_get_input(p->source);
+		if (in)
+			return in;
+	}
+
+	return NULL;
+}
+
+static struct g12a_tohdmitx_input *
+g12a_tohdmitx_get_input_data(struct snd_soc_dapm_widget *w)
+{
+	struct snd_soc_dapm_widget *in =
+		g12a_tohdmitx_get_input(w);
+	struct snd_soc_dai *dai;
+
+	if (WARN_ON(!in))
+		return NULL;
+
+	dai = in->priv;
+
+	return dai->playback_dma_data;
+}
+
+static const char * const g12a_tohdmitx_i2s_mux_texts[] = {
+	"I2S A", "I2S B", "I2S C",
+};
+
+static SOC_ENUM_SINGLE_EXT_DECL(g12a_tohdmitx_i2s_mux_enum,
+				g12a_tohdmitx_i2s_mux_texts);
+
+static int g12a_tohdmitx_get_input_val(struct snd_soc_component *component,
+				       unsigned int mask)
+{
+	unsigned int val;
+
+	snd_soc_component_read(component, TOHDMITX_CTRL0, &val);
+	return (val & mask) >> __ffs(mask);
+}
+
+static int g12a_tohdmitx_i2s_mux_get_enum(struct snd_kcontrol *kcontrol,
+					  struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+
+	ucontrol->value.enumerated.item[0] =
+		g12a_tohdmitx_get_input_val(component, CTRL0_I2S_DAT_SEL);
+
+	return 0;
+}
+
+static int g12a_tohdmitx_i2s_mux_put_enum(struct snd_kcontrol *kcontrol,
+					  struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+	struct snd_soc_dapm_context *dapm =
+		snd_soc_dapm_kcontrol_dapm(kcontrol);
+	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
+	unsigned int mux = ucontrol->value.enumerated.item[0];
+	unsigned int val = g12a_tohdmitx_get_input_val(component,
+						       CTRL0_I2S_DAT_SEL);
+
+	/* Force disconnect of the mux while updating */
+	if (val != mux)
+		snd_soc_dapm_mux_update_power(dapm, kcontrol, 0, NULL, NULL);
+
+	snd_soc_component_update_bits(component, TOHDMITX_CTRL0,
+				      CTRL0_I2S_DAT_SEL |
+				      CTRL0_I2S_LRCLK_SEL |
+				      CTRL0_I2S_BCLK_SEL,
+				      FIELD_PREP(CTRL0_I2S_DAT_SEL, mux) |
+				      FIELD_PREP(CTRL0_I2S_LRCLK_SEL, mux) |
+				      FIELD_PREP(CTRL0_I2S_BCLK_SEL, mux));
+
+	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
+
+	return 0;
+}
+
+static const struct snd_kcontrol_new g12a_tohdmitx_i2s_mux =
+	SOC_DAPM_ENUM_EXT("I2S Source", g12a_tohdmitx_i2s_mux_enum,
+			  g12a_tohdmitx_i2s_mux_get_enum,
+			  g12a_tohdmitx_i2s_mux_put_enum);
+
+static const char * const g12a_tohdmitx_spdif_mux_texts[] = {
+	"SPDIF A", "SPDIF B",
+};
+
+static SOC_ENUM_SINGLE_EXT_DECL(g12a_tohdmitx_spdif_mux_enum,
+				g12a_tohdmitx_spdif_mux_texts);
+
+static int g12a_tohdmitx_spdif_mux_get_enum(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+
+	ucontrol->value.enumerated.item[0] =
+		g12a_tohdmitx_get_input_val(component, CTRL0_SPDIF_SEL);
+
+	return 0;
+}
+
+static int g12a_tohdmitx_spdif_mux_put_enum(struct snd_kcontrol *kcontrol,
+					    struct snd_ctl_elem_value *ucontrol)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_kcontrol_component(kcontrol);
+	struct snd_soc_dapm_context *dapm =
+		snd_soc_dapm_kcontrol_dapm(kcontrol);
+	struct soc_enum *e = (struct soc_enum *)kcontrol->private_value;
+	unsigned int mux = ucontrol->value.enumerated.item[0];
+	unsigned int val = g12a_tohdmitx_get_input_val(component,
+						       CTRL0_SPDIF_SEL);
+
+	/* Force disconnect of the mux while updating */
+	if (val != mux)
+		snd_soc_dapm_mux_update_power(dapm, kcontrol, 0, NULL, NULL);
+
+	snd_soc_component_update_bits(component, TOHDMITX_CTRL0,
+				      CTRL0_SPDIF_SEL |
+				      CTRL0_SPDIF_CLK_SEL,
+				      FIELD_PREP(CTRL0_SPDIF_SEL, mux) |
+				      FIELD_PREP(CTRL0_SPDIF_CLK_SEL, mux));
+
+	snd_soc_dapm_mux_update_power(dapm, kcontrol, mux, e, NULL);
+
+	return 0;
+}
+
+static const struct snd_kcontrol_new g12a_tohdmitx_spdif_mux =
+	SOC_DAPM_ENUM_EXT("SPDIF Source", g12a_tohdmitx_spdif_mux_enum,
+			  g12a_tohdmitx_spdif_mux_get_enum,
+			  g12a_tohdmitx_spdif_mux_put_enum);
+
+static const struct snd_kcontrol_new g12a_tohdmitx_out_enable =
+	SOC_DAPM_SINGLE_AUTODISABLE("Switch", TOHDMITX_CTRL0,
+				    CTRL0_ENABLE_SHIFT, 1, 0);
+
+static const struct snd_soc_dapm_widget g12a_tohdmitx_widgets[] = {
+	SND_SOC_DAPM_MUX("I2S SRC", SND_SOC_NOPM, 0, 0,
+			 &g12a_tohdmitx_i2s_mux),
+	SND_SOC_DAPM_SWITCH("I2S OUT EN", SND_SOC_NOPM, 0, 0,
+			    &g12a_tohdmitx_out_enable),
+	SND_SOC_DAPM_MUX("SPDIF SRC", SND_SOC_NOPM, 0, 0,
+			 &g12a_tohdmitx_spdif_mux),
+	SND_SOC_DAPM_SWITCH("SPDIF OUT EN", SND_SOC_NOPM, 0, 0,
+			    &g12a_tohdmitx_out_enable),
+};
+
+static int g12a_tohdmitx_input_probe(struct snd_soc_dai *dai)
+{
+	struct g12a_tohdmitx_input *data;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	dai->playback_dma_data = data;
+	return 0;
+}
+
+static int g12a_tohdmitx_input_remove(struct snd_soc_dai *dai)
+{
+	kfree(dai->playback_dma_data);
+	return 0;
+}
+
+static int g12a_tohdmitx_input_hw_params(struct snd_pcm_substream *substream,
+					 struct snd_pcm_hw_params *params,
+					 struct snd_soc_dai *dai)
+{
+	struct g12a_tohdmitx_input *data = dai->playback_dma_data;
+
+	/* Save the stream params for the downstream link */
+	memcpy(&data->params, params, sizeof(*params));
+
+	return 0;
+}
+
+static int g12a_tohdmitx_output_hw_params(struct snd_pcm_substream *substream,
+					  struct snd_pcm_hw_params *params,
+					  struct snd_soc_dai *dai)
+{
+	struct g12a_tohdmitx_input *in_data =
+		g12a_tohdmitx_get_input_data(dai->capture_widget);
+
+	if (!in_data)
+		return -ENODEV;
+
+	memcpy(params, &in_data->params, sizeof(*params));
+
+	return 0;
+}
+
+static int g12a_tohdmitx_input_set_fmt(struct snd_soc_dai *dai,
+				       unsigned int fmt)
+{
+	struct g12a_tohdmitx_input *data = dai->playback_dma_data;
+
+	/* Save the source stream format for the downstream link */
+	data->fmt = fmt;
+	return 0;
+}
+
+static int g12a_tohdmitx_output_startup(struct snd_pcm_substream *substream,
+					struct snd_soc_dai *dai)
+{
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct g12a_tohdmitx_input *in_data =
+		g12a_tohdmitx_get_input_data(dai->capture_widget);
+
+	if (!in_data)
+		return -ENODEV;
+
+	if (!in_data->fmt)
+		return 0;
+
+	return snd_soc_runtime_set_dai_fmt(rtd, in_data->fmt);
+}
+
+static const struct snd_soc_dai_ops g12a_tohdmitx_input_ops = {
+	.hw_params	= g12a_tohdmitx_input_hw_params,
+	.set_fmt	= g12a_tohdmitx_input_set_fmt,
+};
+
+static const struct snd_soc_dai_ops g12a_tohdmitx_output_ops = {
+	.hw_params	= g12a_tohdmitx_output_hw_params,
+	.startup	= g12a_tohdmitx_output_startup,
+};
+
+#define TOHDMITX_SPDIF_FORMATS					\
+	(SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |	\
+	 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE)
+
+#define TOHDMITX_I2S_FORMATS					\
+	(SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |	\
+	 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE |	\
+	 SNDRV_PCM_FMTBIT_S32_LE)
+
+#define TOHDMITX_STREAM(xname, xsuffix, xfmt, xchmax)		\
+{								\
+	.stream_name	= xname " " xsuffix,			\
+	.channels_min	= 1,					\
+	.channels_max	= (xchmax),				\
+	.rate_min       = 8000,					\
+	.rate_max	= 192000,				\
+	.formats	= (xfmt),				\
+}
+
+#define TOHDMITX_IN(xname, xid, xfmt, xchmax) {				\
+	.name = xname,							\
+	.id = (xid),							\
+	.playback = TOHDMITX_STREAM(xname, "Playback", xfmt, xchmax),	\
+	.ops = &g12a_tohdmitx_input_ops,				\
+	.probe = g12a_tohdmitx_input_probe,				\
+	.remove = g12a_tohdmitx_input_remove,				\
+}
+
+#define TOHDMITX_OUT(xname, xid, xfmt, xchmax) {			\
+	.name = xname,							\
+	.id = (xid),							\
+	.capture = TOHDMITX_STREAM(xname, "Capture", xfmt, xchmax),	\
+	.ops = &g12a_tohdmitx_output_ops,				\
+}
+
+static struct snd_soc_dai_driver g12a_tohdmitx_dai_drv[] = {
+	TOHDMITX_IN("I2S IN A", TOHDMITX_I2S_IN_A,
+		    TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_IN("I2S IN B", TOHDMITX_I2S_IN_B,
+		    TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_IN("I2S IN C", TOHDMITX_I2S_IN_C,
+		    TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_OUT("I2S OUT", TOHDMITX_I2S_OUT,
+		     TOHDMITX_I2S_FORMATS, 8),
+	TOHDMITX_IN("SPDIF IN A", TOHDMITX_SPDIF_IN_A,
+		    TOHDMITX_SPDIF_FORMATS, 2),
+	TOHDMITX_IN("SPDIF IN B", TOHDMITX_SPDIF_IN_B,
+		    TOHDMITX_SPDIF_FORMATS, 2),
+	TOHDMITX_OUT("SPDIF OUT", TOHDMITX_SPDIF_OUT,
+		     TOHDMITX_SPDIF_FORMATS, 2),
+};
+
+static int g12a_tohdmi_component_probe(struct snd_soc_component *c)
+{
+	/* Initialize the static clock parameters */
+	return snd_soc_component_write(c, TOHDMITX_CTRL0,
+		     CTRL0_I2S_BLK_CAP_INV | CTRL0_SPDIF_CLK_CAP_INV);
+}
+
+static const struct snd_soc_dapm_route g12a_tohdmitx_routes[] = {
+	{ "I2S SRC", "I2S A", "I2S IN A Playback" },
+	{ "I2S SRC", "I2S B", "I2S IN B Playback" },
+	{ "I2S SRC", "I2S C", "I2S IN C Playback" },
+	{ "I2S OUT EN", "Switch", "I2S SRC" },
+	{ "I2S OUT Capture", NULL, "I2S OUT EN" },
+	{ "SPDIF SRC", "SPDIF A", "SPDIF IN A Playback" },
+	{ "SPDIF SRC", "SPDIF B", "SPDIF IN B Playback" },
+	{ "SPDIF OUT EN", "Switch", "SPDIF SRC" },
+	{ "SPDIF OUT Capture", NULL, "SPDIF OUT EN" },
+};
+
+static const struct snd_soc_component_driver g12a_tohdmitx_component_drv = {
+	.probe			= g12a_tohdmi_component_probe,
+	.dapm_widgets		= g12a_tohdmitx_widgets,
+	.num_dapm_widgets	= ARRAY_SIZE(g12a_tohdmitx_widgets),
+	.dapm_routes		= g12a_tohdmitx_routes,
+	.num_dapm_routes	= ARRAY_SIZE(g12a_tohdmitx_routes),
+	.endianness		= 1,
+	.non_legacy_dai_naming	= 1,
+};
+
+static const struct regmap_config g12a_tohdmitx_regmap_cfg = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+};
+
+static const struct of_device_id g12a_tohdmitx_of_match[] = {
+	{ .compatible = "amlogic,g12a-tohdmitx", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, g12a_tohdmitx_of_match);
+
+static int g12a_tohdmitx_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	void __iomem *regs;
+	struct regmap *map;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(regs))
+		return PTR_ERR(regs);
+
+	map = devm_regmap_init_mmio(dev, regs, &g12a_tohdmitx_regmap_cfg);
+	if (IS_ERR(map)) {
+		dev_err(dev, "failed to init regmap: %ld\n",
+			PTR_ERR(map));
+		return PTR_ERR(map);
+	}
+
+	return devm_snd_soc_register_component(dev,
+			&g12a_tohdmitx_component_drv, g12a_tohdmitx_dai_drv,
+			ARRAY_SIZE(g12a_tohdmitx_dai_drv));
+}
+
+static struct platform_driver g12a_tohdmitx_pdrv = {
+	.driver = {
+		.name = G12A_TOHDMITX_DRV_NAME,
+		.of_match_table = g12a_tohdmitx_of_match,
+	},
+	.probe = g12a_tohdmitx_probe,
+};
+module_platform_driver(g12a_tohdmitx_pdrv);
+
+MODULE_AUTHOR("Jerome Brunet <jbrunet@baylibre.com>");
+MODULE_DESCRIPTION("Amlogic G12a To HDMI Tx Control Codec Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.20.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 0/5] ASoC: meson: add hdmitx glue support

[Neil Armstrong]

On 15/05/2019 15:18, Jerome Brunet wrote:
> On the Amlogic SoC, there is a glue between the SoC audio outputs and the
> input of the embedded Synopsys HDMI controller.
> 
> On the g12a, this glue is mostly a couple of muxes to select the i2s and
> spdif inputs of the hdmi controller. Each of these inputs may have
> different hw_params and fmt which makes our life a little bit more
> interesting, especially when switching between to active inputs.
> 
> This glue is modeled as codec driver and uses codec-to-codec links to
> connect to the Synopsys controller. This allows to use the regular
> hdmi-codec driver (used by dw-hdmi i2s).
> 
> To avoid glitches while switching input, the trick is to temporarily
> force a disconnection of the mux output, which shutdowns the output dai
> link. This also ensure that the stream parameters and fmt are updated
> when the output is connected back.
> 
> Jerome Brunet (5):
>   ASoC: meson: axg-card: set link name based on link node name
>   ASoC: dapm: allow muxes to force a disconnect
>   ASoC: meson: add tohdmitx DT bindings
>   ASoC: meson: axg-card: add basic codec-to-codec link support
>   ASoC: meson: add g12a tohdmitx control
> 
>  .../bindings/sound/amlogic,g12a-tohdmitx.txt  |  55 +++
>  .../dt-bindings/sound/meson-g12a-tohdmitx.h   |  13 +
>  sound/soc/meson/Kconfig                       |   8 +
>  sound/soc/meson/Makefile                      |   2 +
>  sound/soc/meson/axg-card.c                    |  31 +-
>  sound/soc/meson/g12a-tohdmitx.c               | 413 ++++++++++++++++++
>  sound/soc/soc-dapm.c                          |   2 +-
>  7 files changed, 518 insertions(+), 6 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/sound/amlogic,g12a-tohdmitx.txt
>  create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h
>  create mode 100644 sound/soc/meson/g12a-tohdmitx.c
> 

Tested-by: Neil Armstrong <narmstrong@baylibre.com>

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 0/5] ASoC: meson: add hdmitx glue support

[Kevin Hilman]

Jerome Brunet <jbrunet@baylibre.com> writes:

> On the Amlogic SoC, there is a glue between the SoC audio outputs and the
> input of the embedded Synopsys HDMI controller.
>
> On the g12a, this glue is mostly a couple of muxes to select the i2s and
> spdif inputs of the hdmi controller. Each of these inputs may have
> different hw_params and fmt which makes our life a little bit more
> interesting, especially when switching between to active inputs.
>
> This glue is modeled as codec driver and uses codec-to-codec links to
> connect to the Synopsys controller. This allows to use the regular
> hdmi-codec driver (used by dw-hdmi i2s).
>
> To avoid glitches while switching input, the trick is to temporarily
> force a disconnection of the mux output, which shutdowns the output dai
> link. This also ensure that the stream parameters and fmt are updated
> when the output is connected back.

Tested-by: Kevin Hilman <khilman@baylibre.com>

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic