* [PATCH 0/6] arm64: g12a: add support for DVFS
@ 2019-07-29 13:26 Neil Armstrong
2019-07-29 13:26 ` [PATCH 1/6] arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi Neil Armstrong
` (6 more replies)
0 siblings, 7 replies; 11+ messages in thread
From: Neil Armstrong @ 2019-07-29 13:26 UTC (permalink / raw)
To: khilman; +Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
The G12A & G12B SoCs has kernel controllable CPU clocks and PWMs for
voltage regulators.
This patchsets moves the meson-g12a.dtsi to meson-g12-common.dtsi to simplify
handling the G12A & G12B differences in the meson-g12a.dtsi & meson-g12b.dtsi
files, like the OPPs and CPU nodes.
Then G12A & G12B OPP tables are added, followed by the CPU voltages regulators
in each boards DT.
It was voluntary chosen to enabled DVFS (CPU regulator and CPU clocks) only
in boards, to make sure only tested boards has DVFS enabled.
This patchset :
- moves the G12A DT to a common g12a-common dtsi
- adds the G12A and G12B OPPs
- enables DVFS on all supported boards
Dependencies:
- None
Changes since RFT/RFC v3 at [3]:
- Rebased on v5.3/fixes branch to take in order the last g12a.dtsi changes.
- added Martin's review tags
Changes since RFT/RFC v2 at [2]:
- Rebased on linux-amlogic v5.3/dt64
Changes since RFT/RFC v1 at [1]:
- Fixed G12B dtsi by adding back the sdio quirk
- Fixed G12A dtsi unwanted sdio quirk removal
[1] https://patchwork.kernel.org/cover/11006929/
[2] https://patchwork.kernel.org/cover/11017273/
[3] https://patchwork.kernel.org/cover/11025309/
Neil Armstrong (6):
arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi
arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux
arm64: dts: meson-g12a: add cpus OPP table
arm64: dts: meson-g12a: enable DVFS on G12A boards
arm64: dts: meson-g12b: add cpus OPP tables
arm64: dts: meson-g12b-odroid-n2: enable DVFS
.../boot/dts/amlogic/meson-g12-common.dtsi | 2417 ++++++++++++++++
.../boot/dts/amlogic/meson-g12a-sei510.dts | 55 +
.../boot/dts/amlogic/meson-g12a-u200.dts | 54 +
.../boot/dts/amlogic/meson-g12a-x96-max.dts | 52 +
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 2418 +----------------
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 96 +
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 145 +-
7 files changed, 2856 insertions(+), 2381 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 1/6] arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
@ 2019-07-29 13:26 ` Neil Armstrong
2019-07-29 13:26 ` [PATCH 2/6] arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux Neil Armstrong
` (5 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Neil Armstrong @ 2019-07-29 13:26 UTC (permalink / raw)
To: khilman; +Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
To simplify the representation of differences betweem the G12A and G12B
SoCs, move the common nodes into a meson-g12-common.dtsi file and
express the CPU nodes and differences in meson-g12a.dtsi and meson-g12b.dtsi.
This separation will help for DVFS and future Amlogic SM1 Family support.
The sd_emmc_a quirk is added in the g12a/g12b since since it's already
known the sd_emmc_a controller is fixed in the next SM1 SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../boot/dts/amlogic/meson-g12-common.dtsi | 2409 +++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 2406 +---------------
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 30 +-
3 files changed, 2440 insertions(+), 2405 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
new file mode 100644
index 000000000000..06e186ca41e3
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -0,0 +1,2409 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/axg-audio-clkc.h>
+#include <dt-bindings/clock/g12a-clkc.h>
+#include <dt-bindings/clock/g12a-aoclkc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
+#include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ tdmif_a: audio-controller-0 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_A";
+ clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_A_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_A_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
+ tdmif_b: audio-controller-1 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_B";
+ clocks = <&clkc_audio AUD_CLKID_MST_B_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
+ tdmif_c: audio-controller-2 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_C";
+ clocks = <&clkc_audio AUD_CLKID_MST_C_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_C_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_C_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
+ efuse: efuse {
+ compatible = "amlogic,meson-gxbb-efuse";
+ clocks = <&clkc CLKID_EFUSE>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ read-only;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 3 MiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@5000000 {
+ reg = <0x0 0x05000000 0x0 0x300000>;
+ no-map;
+ };
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ size = <0x0 0x10000000>;
+ alignment = <0x0 0x400000>;
+ linux,cma-default;
+ };
+ };
+
+ sm: secure-monitor {
+ compatible = "amlogic,meson-gxbb-sm";
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ethmac: ethernet@ff3f0000 {
+ compatible = "amlogic,meson-axg-dwmac",
+ "snps,dwmac-3.70a",
+ "snps,dwmac";
+ reg = <0x0 0xff3f0000 0x0 0x10000
+ 0x0 0xff634540 0x0 0x8>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&clkc CLKID_ETH>,
+ <&clkc CLKID_FCLK_DIV2>,
+ <&clkc CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
+ status = "disabled";
+
+ mdio0: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ };
+ };
+
+ apb: bus@ff600000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xff600000 0x0 0x200000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>;
+
+ hdmi_tx: hdmi-tx@0 {
+ compatible = "amlogic,meson-g12a-dw-hdmi";
+ reg = <0x0 0x0 0x0 0x10000>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
+ resets = <&reset RESET_HDMITX_CAPB3>,
+ <&reset RESET_HDMITX_PHY>,
+ <&reset RESET_HDMITX>;
+ reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
+ clocks = <&clkc CLKID_HDMI>,
+ <&clkc CLKID_HTX_PCLK>,
+ <&clkc CLKID_VPU_INTR>;
+ clock-names = "isfr", "iahb", "venci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <0>;
+ status = "disabled";
+
+ /* VPU VENC Input */
+ hdmi_tx_venc_port: port@0 {
+ reg = <0>;
+
+ hdmi_tx_in: endpoint {
+ remote-endpoint = <&hdmi_tx_out>;
+ };
+ };
+
+ /* TMDS Output */
+ hdmi_tx_tmds_port: port@1 {
+ reg = <1>;
+ };
+ };
+
+ apb_efuse: bus@30000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x30000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x30000 0x0 0x2000>;
+
+ hwrng: rng@218 {
+ compatible = "amlogic,meson-rng";
+ reg = <0x0 0x218 0x0 0x4>;
+ };
+ };
+
+ periphs: bus@34400 {
+ compatible = "simple-bus";
+ reg = <0x0 0x34400 0x0 0x400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x34400 0x0 0x400>;
+
+ periphs_pinctrl: pinctrl@40 {
+ compatible = "amlogic,meson-g12a-periphs-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio: bank@40 {
+ reg = <0x0 0x40 0x0 0x4c>,
+ <0x0 0xe8 0x0 0x18>,
+ <0x0 0x120 0x0 0x18>,
+ <0x0 0x2c0 0x0 0x40>,
+ <0x0 0x340 0x0 0x1c>;
+ reg-names = "gpio",
+ "pull",
+ "pull-enable",
+ "mux",
+ "ds";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&periphs_pinctrl 0 0 86>;
+ };
+
+ cec_ao_a_h_pins: cec_ao_a_h {
+ mux {
+ groups = "cec_ao_a_h";
+ function = "cec_ao_a_h";
+ bias-disable;
+ };
+ };
+
+ cec_ao_b_h_pins: cec_ao_b_h {
+ mux {
+ groups = "cec_ao_b_h";
+ function = "cec_ao_b_h";
+ bias-disable;
+ };
+ };
+
+ emmc_pins: emmc {
+ mux-0 {
+ groups = "emmc_nand_d0",
+ "emmc_nand_d1",
+ "emmc_nand_d2",
+ "emmc_nand_d3",
+ "emmc_nand_d4",
+ "emmc_nand_d5",
+ "emmc_nand_d6",
+ "emmc_nand_d7",
+ "emmc_cmd";
+ function = "emmc";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+
+ mux-1 {
+ groups = "emmc_clk";
+ function = "emmc";
+ bias-disable;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ emmc_ds_pins: emmc-ds {
+ mux {
+ groups = "emmc_nand_ds";
+ function = "emmc";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ hdmitx_ddc_pins: hdmitx_ddc {
+ mux {
+ groups = "hdmitx_sda",
+ "hdmitx_sck";
+ function = "hdmitx";
+ bias-disable;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ hdmitx_hpd_pins: hdmitx_hpd {
+ mux {
+ groups = "hdmitx_hpd_in";
+ function = "hdmitx";
+ bias-disable;
+ };
+ };
+
+
+ i2c0_sda_c_pins: i2c0-sda-c {
+ mux {
+ groups = "i2c0_sda_c";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+
+ };
+ };
+
+ i2c0_sck_c_pins: i2c0-sck-c {
+ mux {
+ groups = "i2c0_sck_c";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z0_pins: i2c0-sda-z0 {
+ mux {
+ groups = "i2c0_sda_z0";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sck_z1_pins: i2c0-sck-z1 {
+ mux {
+ groups = "i2c0_sck_z1";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z7_pins: i2c0-sda-z7 {
+ mux {
+ groups = "i2c0_sda_z7";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_sda_z8_pins: i2c0-sda-z8 {
+ mux {
+ groups = "i2c0_sda_z8";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_x_pins: i2c1-sda-x {
+ mux {
+ groups = "i2c1_sda_x";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_x_pins: i2c1-sck-x {
+ mux {
+ groups = "i2c1_sck_x";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_h2_pins: i2c1-sda-h2 {
+ mux {
+ groups = "i2c1_sda_h2";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_h3_pins: i2c1-sck-h3 {
+ mux {
+ groups = "i2c1_sck_h3";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sda_h6_pins: i2c1-sda-h6 {
+ mux {
+ groups = "i2c1_sda_h6";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_sck_h7_pins: i2c1-sck-h7 {
+ mux {
+ groups = "i2c1_sck_h7";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sda_x_pins: i2c2-sda-x {
+ mux {
+ groups = "i2c2_sda_x";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sck_x_pins: i2c2-sck-x {
+ mux {
+ groups = "i2c2_sck_x";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sda_z_pins: i2c2-sda-z {
+ mux {
+ groups = "i2c2_sda_z";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_sck_z_pins: i2c2-sck-z {
+ mux {
+ groups = "i2c2_sck_z";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sda_h_pins: i2c3-sda-h {
+ mux {
+ groups = "i2c3_sda_h";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sck_h_pins: i2c3-sck-h {
+ mux {
+ groups = "i2c3_sck_h";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sda_a_pins: i2c3-sda-a {
+ mux {
+ groups = "i2c3_sda_a";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_sck_a_pins: i2c3-sck-a {
+ mux {
+ groups = "i2c3_sck_a";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ mclk0_a_pins: mclk0-a {
+ mux {
+ groups = "mclk0_a";
+ function = "mclk0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ mclk1_a_pins: mclk1-a {
+ mux {
+ groups = "mclk1_a";
+ function = "mclk1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ mclk1_x_pins: mclk1-x {
+ mux {
+ groups = "mclk1_x";
+ function = "mclk1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ mclk1_z_pins: mclk1-z {
+ mux {
+ groups = "mclk1_z";
+ function = "mclk1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ pdm_din0_a_pins: pdm-din0-a {
+ mux {
+ groups = "pdm_din0_a";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din0_c_pins: pdm-din0-c {
+ mux {
+ groups = "pdm_din0_c";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din0_x_pins: pdm-din0-x {
+ mux {
+ groups = "pdm_din0_x";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din0_z_pins: pdm-din0-z {
+ mux {
+ groups = "pdm_din0_z";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din1_a_pins: pdm-din1-a {
+ mux {
+ groups = "pdm_din1_a";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din1_c_pins: pdm-din1-c {
+ mux {
+ groups = "pdm_din1_c";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din1_x_pins: pdm-din1-x {
+ mux {
+ groups = "pdm_din1_x";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din1_z_pins: pdm-din1-z {
+ mux {
+ groups = "pdm_din1_z";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din2_a_pins: pdm-din2-a {
+ mux {
+ groups = "pdm_din2_a";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din2_c_pins: pdm-din2-c {
+ mux {
+ groups = "pdm_din2_c";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din2_x_pins: pdm-din2-x {
+ mux {
+ groups = "pdm_din2_x";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din2_z_pins: pdm-din2-z {
+ mux {
+ groups = "pdm_din2_z";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din3_a_pins: pdm-din3-a {
+ mux {
+ groups = "pdm_din3_a";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din3_c_pins: pdm-din3-c {
+ mux {
+ groups = "pdm_din3_c";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din3_x_pins: pdm-din3-x {
+ mux {
+ groups = "pdm_din3_x";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_din3_z_pins: pdm-din3-z {
+ mux {
+ groups = "pdm_din3_z";
+ function = "pdm";
+ bias-disable;
+ };
+ };
+
+ pdm_dclk_a_pins: pdm-dclk-a {
+ mux {
+ groups = "pdm_dclk_a";
+ function = "pdm";
+ bias-disable;
+ drive-strength-microamp = <500>;
+ };
+ };
+
+ pdm_dclk_c_pins: pdm-dclk-c {
+ mux {
+ groups = "pdm_dclk_c";
+ function = "pdm";
+ bias-disable;
+ drive-strength-microamp = <500>;
+ };
+ };
+
+ pdm_dclk_x_pins: pdm-dclk-x {
+ mux {
+ groups = "pdm_dclk_x";
+ function = "pdm";
+ bias-disable;
+ drive-strength-microamp = <500>;
+ };
+ };
+
+ pdm_dclk_z_pins: pdm-dclk-z {
+ mux {
+ groups = "pdm_dclk_z";
+ function = "pdm";
+ bias-disable;
+ drive-strength-microamp = <500>;
+ };
+ };
+
+ pwm_a_pins: pwm-a {
+ mux {
+ groups = "pwm_a";
+ function = "pwm_a";
+ bias-disable;
+ };
+ };
+
+ pwm_b_x7_pins: pwm-b-x7 {
+ mux {
+ groups = "pwm_b_x7";
+ function = "pwm_b";
+ bias-disable;
+ };
+ };
+
+ pwm_b_x19_pins: pwm-b-x19 {
+ mux {
+ groups = "pwm_b_x19";
+ function = "pwm_b";
+ bias-disable;
+ };
+ };
+
+ pwm_c_c_pins: pwm-c-c {
+ mux {
+ groups = "pwm_c_c";
+ function = "pwm_c";
+ bias-disable;
+ };
+ };
+
+ pwm_c_x5_pins: pwm-c-x5 {
+ mux {
+ groups = "pwm_c_x5";
+ function = "pwm_c";
+ bias-disable;
+ };
+ };
+
+ pwm_c_x8_pins: pwm-c-x8 {
+ mux {
+ groups = "pwm_c_x8";
+ function = "pwm_c";
+ bias-disable;
+ };
+ };
+
+ pwm_d_x3_pins: pwm-d-x3 {
+ mux {
+ groups = "pwm_d_x3";
+ function = "pwm_d";
+ bias-disable;
+ };
+ };
+
+ pwm_d_x6_pins: pwm-d-x6 {
+ mux {
+ groups = "pwm_d_x6";
+ function = "pwm_d";
+ bias-disable;
+ };
+ };
+
+ pwm_e_pins: pwm-e {
+ mux {
+ groups = "pwm_e";
+ function = "pwm_e";
+ bias-disable;
+ };
+ };
+
+ pwm_f_x_pins: pwm-f-x {
+ mux {
+ groups = "pwm_f_x";
+ function = "pwm_f";
+ bias-disable;
+ };
+ };
+
+ pwm_f_h_pins: pwm-f-h {
+ mux {
+ groups = "pwm_f_h";
+ function = "pwm_f";
+ bias-disable;
+ };
+ };
+
+ sdcard_c_pins: sdcard_c {
+ mux-0 {
+ groups = "sdcard_d0_c",
+ "sdcard_d1_c",
+ "sdcard_d2_c",
+ "sdcard_d3_c",
+ "sdcard_cmd_c";
+ function = "sdcard";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+
+ mux-1 {
+ groups = "sdcard_clk_c";
+ function = "sdcard";
+ bias-disable;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdcard_clk_gate_c_pins: sdcard_clk_gate_c {
+ mux {
+ groups = "GPIOC_4";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdcard_z_pins: sdcard_z {
+ mux-0 {
+ groups = "sdcard_d0_z",
+ "sdcard_d1_z",
+ "sdcard_d2_z",
+ "sdcard_d3_z",
+ "sdcard_cmd_z";
+ function = "sdcard";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+
+ mux-1 {
+ groups = "sdcard_clk_z";
+ function = "sdcard";
+ bias-disable;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdcard_clk_gate_z_pins: sdcard_clk_gate_z {
+ mux {
+ groups = "GPIOZ_6";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdio_pins: sdio {
+ mux {
+ groups = "sdio_d0",
+ "sdio_d1",
+ "sdio_d2",
+ "sdio_d3",
+ "sdio_clk",
+ "sdio_cmd";
+ function = "sdio";
+ bias-disable;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ spdif_in_a10_pins: spdif-in-a10 {
+ mux {
+ groups = "spdif_in_a10";
+ function = "spdif_in";
+ bias-disable;
+ };
+ };
+
+ spdif_in_a12_pins: spdif-in-a12 {
+ mux {
+ groups = "spdif_in_a12";
+ function = "spdif_in";
+ bias-disable;
+ };
+ };
+
+ spdif_in_h_pins: spdif-in-h {
+ mux {
+ groups = "spdif_in_h";
+ function = "spdif_in";
+ bias-disable;
+ };
+ };
+
+ spdif_out_h_pins: spdif-out-h {
+ mux {
+ groups = "spdif_out_h";
+ function = "spdif_out";
+ drive-strength-microamp = <500>;
+ bias-disable;
+ };
+ };
+
+ spdif_out_a11_pins: spdif-out-a11 {
+ mux {
+ groups = "spdif_out_a11";
+ function = "spdif_out";
+ drive-strength-microamp = <500>;
+ bias-disable;
+ };
+ };
+
+ spdif_out_a13_pins: spdif-out-a13 {
+ mux {
+ groups = "spdif_out_a13";
+ function = "spdif_out";
+ drive-strength-microamp = <500>;
+ bias-disable;
+ };
+ };
+
+ tdm_a_din0_pins: tdm-a-din0 {
+ mux {
+ groups = "tdm_a_din0";
+ function = "tdm_a";
+ bias-disable;
+ };
+ };
+
+
+ tdm_a_din1_pins: tdm-a-din1 {
+ mux {
+ groups = "tdm_a_din1";
+ function = "tdm_a";
+ bias-disable;
+ };
+ };
+
+ tdm_a_dout0_pins: tdm-a-dout0 {
+ mux {
+ groups = "tdm_a_dout0";
+ function = "tdm_a";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_a_dout1_pins: tdm-a-dout1 {
+ mux {
+ groups = "tdm_a_dout1";
+ function = "tdm_a";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_a_fs_pins: tdm-a-fs {
+ mux {
+ groups = "tdm_a_fs";
+ function = "tdm_a";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_a_sclk_pins: tdm-a-sclk {
+ mux {
+ groups = "tdm_a_sclk";
+ function = "tdm_a";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_a_slv_fs_pins: tdm-a-slv-fs {
+ mux {
+ groups = "tdm_a_slv_fs";
+ function = "tdm_a";
+ bias-disable;
+ };
+ };
+
+
+ tdm_a_slv_sclk_pins: tdm-a-slv-sclk {
+ mux {
+ groups = "tdm_a_slv_sclk";
+ function = "tdm_a";
+ bias-disable;
+ };
+ };
+
+ tdm_b_din0_pins: tdm-b-din0 {
+ mux {
+ groups = "tdm_b_din0";
+ function = "tdm_b";
+ bias-disable;
+ };
+ };
+
+ tdm_b_din1_pins: tdm-b-din1 {
+ mux {
+ groups = "tdm_b_din1";
+ function = "tdm_b";
+ bias-disable;
+ };
+ };
+
+ tdm_b_din2_pins: tdm-b-din2 {
+ mux {
+ groups = "tdm_b_din2";
+ function = "tdm_b";
+ bias-disable;
+ };
+ };
+
+ tdm_b_din3_a_pins: tdm-b-din3-a {
+ mux {
+ groups = "tdm_b_din3_a";
+ function = "tdm_b";
+ bias-disable;
+ };
+ };
+
+ tdm_b_din3_h_pins: tdm-b-din3-h {
+ mux {
+ groups = "tdm_b_din3_h";
+ function = "tdm_b";
+ bias-disable;
+ };
+ };
+
+ tdm_b_dout0_pins: tdm-b-dout0 {
+ mux {
+ groups = "tdm_b_dout0";
+ function = "tdm_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_b_dout1_pins: tdm-b-dout1 {
+ mux {
+ groups = "tdm_b_dout1";
+ function = "tdm_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_b_dout2_pins: tdm-b-dout2 {
+ mux {
+ groups = "tdm_b_dout2";
+ function = "tdm_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_b_dout3_a_pins: tdm-b-dout3-a {
+ mux {
+ groups = "tdm_b_dout3_a";
+ function = "tdm_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_b_dout3_h_pins: tdm-b-dout3-h {
+ mux {
+ groups = "tdm_b_dout3_h";
+ function = "tdm_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_b_fs_pins: tdm-b-fs {
+ mux {
+ groups = "tdm_b_fs";
+ function = "tdm_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_b_sclk_pins: tdm-b-sclk {
+ mux {
+ groups = "tdm_b_sclk";
+ function = "tdm_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_b_slv_fs_pins: tdm-b-slv-fs {
+ mux {
+ groups = "tdm_b_slv_fs";
+ function = "tdm_b";
+ bias-disable;
+ };
+ };
+
+ tdm_b_slv_sclk_pins: tdm-b-slv-sclk {
+ mux {
+ groups = "tdm_b_slv_sclk";
+ function = "tdm_b";
+ bias-disable;
+ };
+ };
+
+ tdm_c_din0_a_pins: tdm-c-din0-a {
+ mux {
+ groups = "tdm_c_din0_a";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_din0_z_pins: tdm-c-din0-z {
+ mux {
+ groups = "tdm_c_din0_z";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_din1_a_pins: tdm-c-din1-a {
+ mux {
+ groups = "tdm_c_din1_a";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_din1_z_pins: tdm-c-din1-z {
+ mux {
+ groups = "tdm_c_din1_z";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_din2_a_pins: tdm-c-din2-a {
+ mux {
+ groups = "tdm_c_din2_a";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ eth_leds_pins: eth-leds {
+ mux {
+ groups = "eth_link_led",
+ "eth_act_led";
+ function = "eth";
+ bias-disable;
+ };
+ };
+
+ eth_pins: eth {
+ mux {
+ groups = "eth_mdio",
+ "eth_mdc",
+ "eth_rgmii_rx_clk",
+ "eth_rx_dv",
+ "eth_rxd0",
+ "eth_rxd1",
+ "eth_txen",
+ "eth_txd0",
+ "eth_txd1";
+ function = "eth";
+ drive-strength-microamp = <4000>;
+ bias-disable;
+ };
+ };
+
+ eth_rgmii_pins: eth-rgmii {
+ mux {
+ groups = "eth_rxd2_rgmii",
+ "eth_rxd3_rgmii",
+ "eth_rgmii_tx_clk",
+ "eth_txd2_rgmii",
+ "eth_txd3_rgmii";
+ function = "eth";
+ drive-strength-microamp = <4000>;
+ bias-disable;
+ };
+ };
+
+ tdm_c_din2_z_pins: tdm-c-din2-z {
+ mux {
+ groups = "tdm_c_din2_z";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_din3_a_pins: tdm-c-din3-a {
+ mux {
+ groups = "tdm_c_din3_a";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_din3_z_pins: tdm-c-din3-z {
+ mux {
+ groups = "tdm_c_din3_z";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_dout0_a_pins: tdm-c-dout0-a {
+ mux {
+ groups = "tdm_c_dout0_a";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_dout0_z_pins: tdm-c-dout0-z {
+ mux {
+ groups = "tdm_c_dout0_z";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_dout1_a_pins: tdm-c-dout1-a {
+ mux {
+ groups = "tdm_c_dout1_a";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_dout1_z_pins: tdm-c-dout1-z {
+ mux {
+ groups = "tdm_c_dout1_z";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_dout2_a_pins: tdm-c-dout2-a {
+ mux {
+ groups = "tdm_c_dout2_a";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_dout2_z_pins: tdm-c-dout2-z {
+ mux {
+ groups = "tdm_c_dout2_z";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_dout3_a_pins: tdm-c-dout3-a {
+ mux {
+ groups = "tdm_c_dout3_a";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_dout3_z_pins: tdm-c-dout3-z {
+ mux {
+ groups = "tdm_c_dout3_z";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_fs_a_pins: tdm-c-fs-a {
+ mux {
+ groups = "tdm_c_fs_a";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_fs_z_pins: tdm-c-fs-z {
+ mux {
+ groups = "tdm_c_fs_z";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_sclk_a_pins: tdm-c-sclk-a {
+ mux {
+ groups = "tdm_c_sclk_a";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_sclk_z_pins: tdm-c-sclk-z {
+ mux {
+ groups = "tdm_c_sclk_z";
+ function = "tdm_c";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_c_slv_fs_a_pins: tdm-c-slv-fs-a {
+ mux {
+ groups = "tdm_c_slv_fs_a";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_slv_fs_z_pins: tdm-c-slv-fs-z {
+ mux {
+ groups = "tdm_c_slv_fs_z";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_slv_sclk_a_pins: tdm-c-slv-sclk-a {
+ mux {
+ groups = "tdm_c_slv_sclk_a";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ tdm_c_slv_sclk_z_pins: tdm-c-slv-sclk-z {
+ mux {
+ groups = "tdm_c_slv_sclk_z";
+ function = "tdm_c";
+ bias-disable;
+ };
+ };
+
+ uart_a_pins: uart-a {
+ mux {
+ groups = "uart_a_tx",
+ "uart_a_rx";
+ function = "uart_a";
+ bias-disable;
+ };
+ };
+
+ uart_a_cts_rts_pins: uart-a-cts-rts {
+ mux {
+ groups = "uart_a_cts",
+ "uart_a_rts";
+ function = "uart_a";
+ bias-disable;
+ };
+ };
+
+ uart_b_pins: uart-b {
+ mux {
+ groups = "uart_b_tx",
+ "uart_b_rx";
+ function = "uart_b";
+ bias-disable;
+ };
+ };
+
+ uart_c_pins: uart-c {
+ mux {
+ groups = "uart_c_tx",
+ "uart_c_rx";
+ function = "uart_c";
+ bias-disable;
+ };
+ };
+
+ uart_c_cts_rts_pins: uart-c-cts-rts {
+ mux {
+ groups = "uart_c_cts",
+ "uart_c_rts";
+ function = "uart_c";
+ bias-disable;
+ };
+ };
+ };
+ };
+
+ usb2_phy0: phy@36000 {
+ compatible = "amlogic,g12a-usb2-phy";
+ reg = <0x0 0x36000 0x0 0x2000>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
+ resets = <&reset RESET_USB_PHY20>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
+ dmc: bus@38000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x38000 0x0 0x400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>;
+
+ canvas: video-lut@48 {
+ compatible = "amlogic,canvas";
+ reg = <0x0 0x48 0x0 0x14>;
+ };
+ };
+
+ usb2_phy1: phy@3a000 {
+ compatible = "amlogic,g12a-usb2-phy";
+ reg = <0x0 0x3a000 0x0 0x2000>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
+ resets = <&reset RESET_USB_PHY21>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
+ hiu: bus@3c000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x3c000 0x0 0x1400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x3c000 0x0 0x1400>;
+
+ hhi: system-controller@0 {
+ compatible = "amlogic,meson-gx-hhi-sysctrl",
+ "simple-mfd", "syscon";
+ reg = <0 0 0 0x400>;
+
+ clkc: clock-controller {
+ compatible = "amlogic,g12a-clkc";
+ #clock-cells = <1>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
+ };
+ };
+ };
+
+ pdm: audio-controller@40000 {
+ compatible = "amlogic,g12a-pdm",
+ "amlogic,axg-pdm";
+ reg = <0x0 0x40000 0x0 0x34>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "PDM";
+ clocks = <&clkc_audio AUD_CLKID_PDM>,
+ <&clkc_audio AUD_CLKID_PDM_DCLK>,
+ <&clkc_audio AUD_CLKID_PDM_SYSCLK>;
+ clock-names = "pclk", "dclk", "sysclk";
+ status = "disabled";
+ };
+
+ audio: bus@42000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x42000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x42000 0x0 0x2000>;
+
+ clkc_audio: clock-controller@0 {
+ status = "disabled";
+ compatible = "amlogic,g12a-audio-clkc";
+ reg = <0x0 0x0 0x0 0xb4>;
+ #clock-cells = <1>;
+
+ clocks = <&clkc CLKID_AUDIO>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>,
+ <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL3>,
+ <&clkc CLKID_HIFI_PLL>,
+ <&clkc CLKID_FCLK_DIV3>,
+ <&clkc CLKID_FCLK_DIV4>,
+ <&clkc CLKID_GP0_PLL>;
+ clock-names = "pclk",
+ "mst_in0",
+ "mst_in1",
+ "mst_in2",
+ "mst_in3",
+ "mst_in4",
+ "mst_in5",
+ "mst_in6",
+ "mst_in7";
+
+ resets = <&reset RESET_AUDIO>;
+ };
+
+ toddr_a: audio-controller@100 {
+ compatible = "amlogic,g12a-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x100 0x0 0x1c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_A";
+ interrupts = <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_A>;
+ resets = <&arb AXG_ARB_TODDR_A>;
+ status = "disabled";
+ };
+
+ toddr_b: audio-controller@140 {
+ compatible = "amlogic,g12a-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x140 0x0 0x1c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_B";
+ interrupts = <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_B>;
+ resets = <&arb AXG_ARB_TODDR_B>;
+ status = "disabled";
+ };
+
+ toddr_c: audio-controller@180 {
+ compatible = "amlogic,g12a-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x180 0x0 0x1c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_C";
+ interrupts = <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_C>;
+ resets = <&arb AXG_ARB_TODDR_C>;
+ status = "disabled";
+ };
+
+ frddr_a: audio-controller@1c0 {
+ compatible = "amlogic,g12a-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x1c0 0x0 0x1c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_A";
+ interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
+ resets = <&arb AXG_ARB_FRDDR_A>;
+ status = "disabled";
+ };
+
+ frddr_b: audio-controller@200 {
+ compatible = "amlogic,g12a-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x200 0x0 0x1c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_B";
+ interrupts = <GIC_SPI 153 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_B>;
+ resets = <&arb AXG_ARB_FRDDR_B>;
+ status = "disabled";
+ };
+
+ frddr_c: audio-controller@240 {
+ compatible = "amlogic,g12a-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x240 0x0 0x1c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_C";
+ interrupts = <GIC_SPI 154 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_C>;
+ resets = <&arb AXG_ARB_FRDDR_C>;
+ status = "disabled";
+ };
+
+ arb: reset-controller@280 {
+ status = "disabled";
+ compatible = "amlogic,meson-axg-audio-arb";
+ reg = <0x0 0x280 0x0 0x4>;
+ #reset-cells = <1>;
+ clocks = <&clkc_audio AUD_CLKID_DDR_ARB>;
+ };
+
+ tdmin_a: audio-controller@300 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x300 0x0 0x40>;
+ sound-name-prefix = "TDMIN_A";
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_A>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_b: audio-controller@340 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x340 0x0 0x40>;
+ sound-name-prefix = "TDMIN_B";
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_B>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_c: audio-controller@380 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x380 0x0 0x40>;
+ sound-name-prefix = "TDMIN_C";
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_C>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_lb: audio-controller@3c0 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x3c0 0x0 0x40>;
+ sound-name-prefix = "TDMIN_LB";
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_LB>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ spdifin: audio-controller@400 {
+ compatible = "amlogic,g12a-spdifin",
+ "amlogic,axg-spdifin";
+ reg = <0x0 0x400 0x0 0x30>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFIN";
+ interrupts = <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
+ <&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
+ clock-names = "pclk", "refclk";
+ status = "disabled";
+ };
+
+ spdifout: audio-controller@480 {
+ compatible = "amlogic,g12a-spdifout",
+ "amlogic,axg-spdifout";
+ reg = <0x0 0x480 0x0 0x50>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFOUT";
+ clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
+ <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
+ clock-names = "pclk", "mclk";
+ status = "disabled";
+ };
+
+ tdmout_a: audio-controller@500 {
+ compatible = "amlogic,g12a-tdmout";
+ reg = <0x0 0x500 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_A";
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmout_b: audio-controller@540 {
+ compatible = "amlogic,g12a-tdmout";
+ reg = <0x0 0x540 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_B";
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_B>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmout_c: audio-controller@580 {
+ compatible = "amlogic,g12a-tdmout";
+ reg = <0x0 0x580 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_C";
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_C>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ spdifout_b: audio-controller@680 {
+ compatible = "amlogic,g12a-spdifout",
+ "amlogic,axg-spdifout";
+ reg = <0x0 0x680 0x0 0x50>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFOUT_B";
+ clocks = <&clkc_audio AUD_CLKID_SPDIFOUT_B>,
+ <&clkc_audio AUD_CLKID_SPDIFOUT_B_CLK>;
+ clock-names = "pclk", "mclk";
+ status = "disabled";
+ };
+
+ tohdmitx: audio-controller@744 {
+ compatible = "amlogic,g12a-tohdmitx";
+ reg = <0x0 0x744 0x0 0x4>;
+ #sound-dai-cells = <1>;
+ sound-name-prefix = "TOHDMITX";
+ status = "disabled";
+ };
+ };
+
+ usb3_pcie_phy: phy@46000 {
+ compatible = "amlogic,g12a-usb3-pcie-phy";
+ reg = <0x0 0x46000 0x0 0x2000>;
+ clocks = <&clkc CLKID_PCIE_PLL>;
+ clock-names = "ref_clk";
+ resets = <&reset RESET_PCIE_PHY>;
+ reset-names = "phy";
+ assigned-clocks = <&clkc CLKID_PCIE_PLL>;
+ assigned-clock-rates = <100000000>;
+ #phy-cells = <1>;
+ };
+
+ eth_phy: mdio-multiplexer@4c000 {
+ compatible = "amlogic,g12a-mdio-mux";
+ reg = <0x0 0x4c000 0x0 0xa4>;
+ clocks = <&clkc CLKID_ETH_PHY>,
+ <&xtal>,
+ <&clkc CLKID_MPLL_50M>;
+ clock-names = "pclk", "clkin0", "clkin1";
+ mdio-parent-bus = <&mdio0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ext_mdio: mdio@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ int_mdio: mdio@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ internal_ephy: ethernet_phy@8 {
+ compatible = "ethernet-phy-id0180.3301",
+ "ethernet-phy-ieee802.3-c22";
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <8>;
+ max-speed = <100>;
+ };
+ };
+ };
+ };
+
+ aobus: bus@ff800000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xff800000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
+
+ rti: sys-ctrl@0 {
+ compatible = "amlogic,meson-gx-ao-sysctrl",
+ "simple-mfd", "syscon";
+ reg = <0x0 0x0 0x0 0x100>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x0 0x0 0x100>;
+
+ clkc_AO: clock-controller {
+ compatible = "amlogic,meson-g12a-aoclkc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ clocks = <&xtal>, <&clkc CLKID_CLK81>;
+ clock-names = "xtal", "mpeg-clk";
+ };
+
+ pwrc_vpu: power-controller-vpu {
+ compatible = "amlogic,meson-g12a-pwrc-vpu";
+ #power-domain-cells = <0>;
+ amlogic,hhi-sysctrl = <&hhi>;
+ resets = <&reset RESET_VIU>,
+ <&reset RESET_VENC>,
+ <&reset RESET_VCBUS>,
+ <&reset RESET_BT656>,
+ <&reset RESET_RDMA>,
+ <&reset RESET_VENCI>,
+ <&reset RESET_VENCP>,
+ <&reset RESET_VDAC>,
+ <&reset RESET_VDI6>,
+ <&reset RESET_VENCL>,
+ <&reset RESET_VID_LOCK>;
+ clocks = <&clkc CLKID_VPU>,
+ <&clkc CLKID_VAPB>;
+ clock-names = "vpu", "vapb";
+ /*
+ * VPU clocking is provided by two identical clock paths
+ * VPU_0 and VPU_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ * Same for VAPB but with a final gate after the glitch free mux.
+ */
+ assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_VPU>, /* Glitch free mux */
+ <&clkc CLKID_VAPB_0_SEL>,
+ <&clkc CLKID_VAPB_0>,
+ <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_FCLK_DIV4>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VAPB_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <666666666>,
+ <0>, /* Do Nothing */
+ <0>, /* Do Nothing */
+ <250000000>,
+ <0>; /* Do Nothing */
+ };
+
+ ao_pinctrl: pinctrl@14 {
+ compatible = "amlogic,meson-g12a-aobus-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio_ao: bank@14 {
+ reg = <0x0 0x14 0x0 0x8>,
+ <0x0 0x1c 0x0 0x8>,
+ <0x0 0x24 0x0 0x14>;
+ reg-names = "mux",
+ "ds",
+ "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&ao_pinctrl 0 0 15>;
+ };
+
+ i2c_ao_sck_pins: i2c_ao_sck_pins {
+ mux {
+ groups = "i2c_ao_sck";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sda_pins: i2c_ao_sda {
+ mux {
+ groups = "i2c_ao_sda";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sck_e_pins: i2c_ao_sck_e {
+ mux {
+ groups = "i2c_ao_sck_e";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c_ao_sda_e_pins: i2c_ao_sda_e {
+ mux {
+ groups = "i2c_ao_sda_e";
+ function = "i2c_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ mclk0_ao_pins: mclk0-ao {
+ mux {
+ groups = "mclk0_ao";
+ function = "mclk0_ao";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_ao_b_din0_pins: tdm-ao-b-din0 {
+ mux {
+ groups = "tdm_ao_b_din0";
+ function = "tdm_ao_b";
+ bias-disable;
+ };
+ };
+
+ spdif_ao_out_pins: spdif-ao-out {
+ mux {
+ groups = "spdif_ao_out";
+ function = "spdif_ao_out";
+ drive-strength-microamp = <500>;
+ bias-disable;
+ };
+ };
+
+ tdm_ao_b_din1_pins: tdm-ao-b-din1 {
+ mux {
+ groups = "tdm_ao_b_din1";
+ function = "tdm_ao_b";
+ bias-disable;
+ };
+ };
+
+ tdm_ao_b_din2_pins: tdm-ao-b-din2 {
+ mux {
+ groups = "tdm_ao_b_din2";
+ function = "tdm_ao_b";
+ bias-disable;
+ };
+ };
+
+ tdm_ao_b_dout0_pins: tdm-ao-b-dout0 {
+ mux {
+ groups = "tdm_ao_b_dout0";
+ function = "tdm_ao_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_ao_b_dout1_pins: tdm-ao-b-dout1 {
+ mux {
+ groups = "tdm_ao_b_dout1";
+ function = "tdm_ao_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_ao_b_dout2_pins: tdm-ao-b-dout2 {
+ mux {
+ groups = "tdm_ao_b_dout2";
+ function = "tdm_ao_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_ao_b_fs_pins: tdm-ao-b-fs {
+ mux {
+ groups = "tdm_ao_b_fs";
+ function = "tdm_ao_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_ao_b_sclk_pins: tdm-ao-b-sclk {
+ mux {
+ groups = "tdm_ao_b_sclk";
+ function = "tdm_ao_b";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ tdm_ao_b_slv_fs_pins: tdm-ao-b-slv-fs {
+ mux {
+ groups = "tdm_ao_b_slv_fs";
+ function = "tdm_ao_b";
+ bias-disable;
+ };
+ };
+
+ tdm_ao_b_slv_sclk_pins: tdm-ao-b-slv-sclk {
+ mux {
+ groups = "tdm_ao_b_slv_sclk";
+ function = "tdm_ao_b";
+ bias-disable;
+ };
+ };
+
+ uart_ao_a_pins: uart-a-ao {
+ mux {
+ groups = "uart_ao_a_tx",
+ "uart_ao_a_rx";
+ function = "uart_ao_a";
+ bias-disable;
+ };
+ };
+
+ uart_ao_a_cts_rts_pins: uart-ao-a-cts-rts {
+ mux {
+ groups = "uart_ao_a_cts",
+ "uart_ao_a_rts";
+ function = "uart_ao_a";
+ bias-disable;
+ };
+ };
+
+ pwm_ao_a_pins: pwm-ao-a {
+ mux {
+ groups = "pwm_ao_a";
+ function = "pwm_ao_a";
+ bias-disable;
+ };
+ };
+
+ pwm_ao_b_pins: pwm-ao-b {
+ mux {
+ groups = "pwm_ao_b";
+ function = "pwm_ao_b";
+ bias-disable;
+ };
+ };
+
+ pwm_ao_c_4_pins: pwm-ao-c-4 {
+ mux {
+ groups = "pwm_ao_c_4";
+ function = "pwm_ao_c";
+ bias-disable;
+ };
+ };
+
+ pwm_ao_c_6_pins: pwm-ao-c-6 {
+ mux {
+ groups = "pwm_ao_c_6";
+ function = "pwm_ao_c";
+ bias-disable;
+ };
+ };
+
+ pwm_ao_d_5_pins: pwm-ao-d-5 {
+ mux {
+ groups = "pwm_ao_d_5";
+ function = "pwm_ao_d";
+ bias-disable;
+ };
+ };
+
+ pwm_ao_d_10_pins: pwm-ao-d-10 {
+ mux {
+ groups = "pwm_ao_d_10";
+ function = "pwm_ao_d";
+ bias-disable;
+ };
+ };
+
+ pwm_ao_d_e_pins: pwm-ao-d-e {
+ mux {
+ groups = "pwm_ao_d_e";
+ function = "pwm_ao_d";
+ };
+ };
+
+ remote_input_ao_pins: remote-input-ao {
+ mux {
+ groups = "remote_ao_input";
+ function = "remote_ao_input";
+ bias-disable;
+ };
+ };
+ };
+ };
+
+ cec_AO: cec@100 {
+ compatible = "amlogic,meson-gx-ao-cec";
+ reg = <0x0 0x00100 0x0 0x14>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_AO CLKID_AO_CEC>;
+ clock-names = "core";
+ status = "disabled";
+ };
+
+ sec_AO: ao-secure@140 {
+ compatible = "amlogic,meson-gx-ao-secure", "syscon";
+ reg = <0x0 0x140 0x0 0x140>;
+ amlogic,has-chip-id;
+ };
+
+ cecb_AO: cec@280 {
+ compatible = "amlogic,meson-g12a-ao-cec";
+ reg = <0x0 0x00280 0x0 0x1c>;
+ interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>;
+ clock-names = "oscin";
+ status = "disabled";
+ };
+
+ pwm_AO_cd: pwm@2000 {
+ compatible = "amlogic,meson-g12a-ao-pwm-cd";
+ reg = <0x0 0x2000 0x0 0x20>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ uart_AO: serial@3000 {
+ compatible = "amlogic,meson-gx-uart",
+ "amlogic,meson-ao-uart";
+ reg = <0x0 0x3000 0x0 0x18>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&clkc_AO CLKID_AO_UART>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+
+ uart_AO_B: serial@4000 {
+ compatible = "amlogic,meson-gx-uart",
+ "amlogic,meson-ao-uart";
+ reg = <0x0 0x4000 0x0 0x18>;
+ interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+
+ i2c_AO: i2c@5000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x05000 0x0 0x20>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ pwm_AO_ab: pwm@7000 {
+ compatible = "amlogic,meson-g12a-ao-pwm-ab";
+ reg = <0x0 0x7000 0x0 0x20>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ ir: ir@8000 {
+ compatible = "amlogic,meson-gxbb-ir";
+ reg = <0x0 0x8000 0x0 0x20>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+
+ saradc: adc@9000 {
+ compatible = "amlogic,meson-g12a-saradc",
+ "amlogic,meson-saradc";
+ reg = <0x0 0x9000 0x0 0x48>;
+ #io-channel-cells = <1>;
+ interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>,
+ <&clkc_AO CLKID_AO_SAR_ADC>,
+ <&clkc_AO CLKID_AO_SAR_ADC_CLK>,
+ <&clkc_AO CLKID_AO_SAR_ADC_SEL>;
+ clock-names = "clkin", "core", "adc_clk", "adc_sel";
+ status = "disabled";
+ };
+ };
+
+ vpu: vpu@ff900000 {
+ compatible = "amlogic,meson-g12a-vpu";
+ reg = <0x0 0xff900000 0x0 0x100000>,
+ <0x0 0xff63c000 0x0 0x1000>;
+ reg-names = "vpu", "hhi";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ amlogic,canvas = <&canvas>;
+ power-domains = <&pwrc_vpu>;
+
+ /* CVBS VDAC output port */
+ cvbs_vdac_port: port@0 {
+ reg = <0>;
+ };
+
+ /* HDMI-TX output port */
+ hdmi_tx_port: port@1 {
+ reg = <1>;
+
+ hdmi_tx_out: endpoint {
+ remote-endpoint = <&hdmi_tx_in>;
+ };
+ };
+ };
+
+ gic: interrupt-controller@ffc01000 {
+ compatible = "arm,gic-400";
+ reg = <0x0 0xffc01000 0 0x1000>,
+ <0x0 0xffc02000 0 0x2000>,
+ <0x0 0xffc04000 0 0x2000>,
+ <0x0 0xffc06000 0 0x2000>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ cbus: bus@ffd00000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xffd00000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x100000>;
+
+ reset: reset-controller@1004 {
+ compatible = "amlogic,meson-g12a-reset",
+ "amlogic,meson-axg-reset";
+ reg = <0x0 0x1004 0x0 0x9c>;
+ #reset-cells = <1>;
+ };
+
+ gpio_intc: interrupt-controller@f080 {
+ compatible = "amlogic,meson-g12a-gpio-intc",
+ "amlogic,meson-gpio-intc";
+ reg = <0x0 0xf080 0x0 0x10>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
+ };
+
+ pwm_ef: pwm@19000 {
+ compatible = "amlogic,meson-g12a-ee-pwm";
+ reg = <0x0 0x19000 0x0 0x20>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_cd: pwm@1a000 {
+ compatible = "amlogic,meson-g12a-ee-pwm";
+ reg = <0x0 0x1a000 0x0 0x20>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_ab: pwm@1b000 {
+ compatible = "amlogic,meson-g12a-ee-pwm";
+ reg = <0x0 0x1b000 0x0 0x20>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@1c000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1c000 0x0 0x20>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c2: i2c@1d000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1d000 0x0 0x20>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c1: i2c@1e000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1e000 0x0 0x20>;
+ interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ i2c0: i2c@1f000 {
+ compatible = "amlogic,meson-axg-i2c";
+ status = "disabled";
+ reg = <0x0 0x1f000 0x0 0x20>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_I2C>;
+ };
+
+ clk_msr: clock-measure@18000 {
+ compatible = "amlogic,meson-g12a-clk-measure";
+ reg = <0x0 0x18000 0x0 0x10>;
+ };
+
+ uart_C: serial@22000 {
+ compatible = "amlogic,meson-gx-uart";
+ reg = <0x0 0x22000 0x0 0x18>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+
+ uart_B: serial@23000 {
+ compatible = "amlogic,meson-gx-uart";
+ reg = <0x0 0x23000 0x0 0x18>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+
+ uart_A: serial@24000 {
+ compatible = "amlogic,meson-gx-uart";
+ reg = <0x0 0x24000 0x0 0x18>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+ };
+
+ sd_emmc_a: sd@ffe03000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0xffe03000 0x0 0x800>;
+ interrupts = <GIC_SPI 189 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ clocks = <&clkc CLKID_SD_EMMC_A>,
+ <&clkc CLKID_SD_EMMC_A_CLK0>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ resets = <&reset RESET_SD_EMMC_A>;
+ };
+
+ sd_emmc_b: sd@ffe05000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0xffe05000 0x0 0x800>;
+ interrupts = <GIC_SPI 190 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ clocks = <&clkc CLKID_SD_EMMC_B>,
+ <&clkc CLKID_SD_EMMC_B_CLK0>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ resets = <&reset RESET_SD_EMMC_B>;
+ };
+
+ sd_emmc_c: mmc@ffe07000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0xffe07000 0x0 0x800>;
+ interrupts = <GIC_SPI 191 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ clocks = <&clkc CLKID_SD_EMMC_C>,
+ <&clkc CLKID_SD_EMMC_C_CLK0>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ resets = <&reset RESET_SD_EMMC_C>;
+ };
+
+ usb: usb@ffe09000 {
+ status = "disabled";
+ compatible = "amlogic,meson-g12a-usb-ctrl";
+ reg = <0x0 0xffe09000 0x0 0xa0>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&clkc CLKID_USB>;
+ resets = <&reset RESET_USB>;
+
+ dr_mode = "otg";
+
+ phys = <&usb2_phy0>, <&usb2_phy1>,
+ <&usb3_pcie_phy PHY_TYPE_USB3>;
+ phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
+
+ dwc2: usb@ff400000 {
+ compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+ reg = <0x0 0xff400000 0x0 0x40000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+ clock-names = "ddr";
+ phys = <&usb2_phy1>;
+ phy-names = "usb2-phy";
+ dr_mode = "peripheral";
+ g-rx-fifo-size = <192>;
+ g-np-tx-fifo-size = <128>;
+ g-tx-fifo-size = <128 128 16 16 16>;
+ };
+
+ dwc3: usb@ff500000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff500000 0x0 0x100000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "host";
+ snps,dis_u2_susphy_quirk;
+ snps,quirk-frame-length-adjustment;
+ };
+ };
+
+ mali: gpu@ffe40000 {
+ compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost";
+ reg = <0x0 0xffe40000 0x0 0x40000>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gpu", "mmu", "job";
+ clocks = <&clkc CLKID_MALI>;
+ resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>;
+
+ /*
+ * Mali clocking is provided by two identical clock paths
+ * MALI_0 and MALI_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ */
+ assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
+ <&clkc CLKID_MALI_0>,
+ <&clkc CLKID_MALI>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV2P5>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_MALI_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <800000000>,
+ <0>; /* Do Nothing */
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ xtal: xtal-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
index 1785552d450c..ac15967bb7fa 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -3,56 +3,11 @@
* Copyright (c) 2018 Amlogic, Inc. All rights reserved.
*/
-#include <dt-bindings/phy/phy.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/axg-audio-clkc.h>
-#include <dt-bindings/clock/g12a-clkc.h>
-#include <dt-bindings/clock/g12a-aoclkc.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
-#include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
+#include "meson-g12-common.dtsi"
/ {
compatible = "amlogic,g12a";
- interrupt-parent = <&gic>;
- #address-cells = <2>;
- #size-cells = <2>;
-
- tdmif_a: audio-controller-0 {
- compatible = "amlogic,axg-tdm-iface";
- #sound-dai-cells = <0>;
- sound-name-prefix = "TDM_A";
- clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>,
- <&clkc_audio AUD_CLKID_MST_A_SCLK>,
- <&clkc_audio AUD_CLKID_MST_A_LRCLK>;
- clock-names = "mclk", "sclk", "lrclk";
- status = "disabled";
- };
-
- tdmif_b: audio-controller-1 {
- compatible = "amlogic,axg-tdm-iface";
- #sound-dai-cells = <0>;
- sound-name-prefix = "TDM_B";
- clocks = <&clkc_audio AUD_CLKID_MST_B_MCLK>,
- <&clkc_audio AUD_CLKID_MST_B_SCLK>,
- <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
- clock-names = "mclk", "sclk", "lrclk";
- status = "disabled";
- };
-
- tdmif_c: audio-controller-2 {
- compatible = "amlogic,axg-tdm-iface";
- #sound-dai-cells = <0>;
- sound-name-prefix = "TDM_C";
- clocks = <&clkc_audio AUD_CLKID_MST_C_MCLK>,
- <&clkc_audio AUD_CLKID_MST_C_SCLK>,
- <&clkc_audio AUD_CLKID_MST_C_LRCLK>;
- clock-names = "mclk", "sclk", "lrclk";
- status = "disabled";
- };
-
cpus {
#address-cells = <0x2>;
#size-cells = <0x0>;
@@ -93,2361 +48,8 @@
compatible = "cache";
};
};
+};
- efuse: efuse {
- compatible = "amlogic,meson-gxbb-efuse";
- clocks = <&clkc CLKID_EFUSE>;
- #address-cells = <1>;
- #size-cells = <1>;
- read-only;
- };
-
- psci {
- compatible = "arm,psci-1.0";
- method = "smc";
- };
-
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- /* 3 MiB reserved for ARM Trusted Firmware (BL31) */
- secmon_reserved: secmon@5000000 {
- reg = <0x0 0x05000000 0x0 0x300000>;
- no-map;
- };
-
- linux,cma {
- compatible = "shared-dma-pool";
- reusable;
- size = <0x0 0x10000000>;
- alignment = <0x0 0x400000>;
- linux,cma-default;
- };
- };
-
- sm: secure-monitor {
- compatible = "amlogic,meson-gxbb-sm";
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- ethmac: ethernet@ff3f0000 {
- compatible = "amlogic,meson-axg-dwmac",
- "snps,dwmac-3.70a",
- "snps,dwmac";
- reg = <0x0 0xff3f0000 0x0 0x10000
- 0x0 0xff634540 0x0 0x8>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
- clocks = <&clkc CLKID_ETH>,
- <&clkc CLKID_FCLK_DIV2>,
- <&clkc CLKID_MPLL2>;
- clock-names = "stmmaceth", "clkin0", "clkin1";
- status = "disabled";
-
- mdio0: mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- };
- };
-
- apb: bus@ff600000 {
- compatible = "simple-bus";
- reg = <0x0 0xff600000 0x0 0x200000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>;
-
- hdmi_tx: hdmi-tx@0 {
- compatible = "amlogic,meson-g12a-dw-hdmi";
- reg = <0x0 0x0 0x0 0x10000>;
- interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
- resets = <&reset RESET_HDMITX_CAPB3>,
- <&reset RESET_HDMITX_PHY>,
- <&reset RESET_HDMITX>;
- reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
- clocks = <&clkc CLKID_HDMI>,
- <&clkc CLKID_HTX_PCLK>,
- <&clkc CLKID_VPU_INTR>;
- clock-names = "isfr", "iahb", "venci";
- #address-cells = <1>;
- #size-cells = <0>;
- #sound-dai-cells = <0>;
- status = "disabled";
-
- /* VPU VENC Input */
- hdmi_tx_venc_port: port@0 {
- reg = <0>;
-
- hdmi_tx_in: endpoint {
- remote-endpoint = <&hdmi_tx_out>;
- };
- };
-
- /* TMDS Output */
- hdmi_tx_tmds_port: port@1 {
- reg = <1>;
- };
- };
-
- apb_efuse: bus@30000 {
- compatible = "simple-bus";
- reg = <0x0 0x30000 0x0 0x2000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0x30000 0x0 0x2000>;
-
- hwrng: rng@218 {
- compatible = "amlogic,meson-rng";
- reg = <0x0 0x218 0x0 0x4>;
- };
- };
-
- periphs: bus@34400 {
- compatible = "simple-bus";
- reg = <0x0 0x34400 0x0 0x400>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0x34400 0x0 0x400>;
-
- periphs_pinctrl: pinctrl@40 {
- compatible = "amlogic,meson-g12a-periphs-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio: bank@40 {
- reg = <0x0 0x40 0x0 0x4c>,
- <0x0 0xe8 0x0 0x18>,
- <0x0 0x120 0x0 0x18>,
- <0x0 0x2c0 0x0 0x40>,
- <0x0 0x340 0x0 0x1c>;
- reg-names = "gpio",
- "pull",
- "pull-enable",
- "mux",
- "ds";
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&periphs_pinctrl 0 0 86>;
- };
-
- cec_ao_a_h_pins: cec_ao_a_h {
- mux {
- groups = "cec_ao_a_h";
- function = "cec_ao_a_h";
- bias-disable;
- };
- };
-
- cec_ao_b_h_pins: cec_ao_b_h {
- mux {
- groups = "cec_ao_b_h";
- function = "cec_ao_b_h";
- bias-disable;
- };
- };
-
- emmc_pins: emmc {
- mux-0 {
- groups = "emmc_nand_d0",
- "emmc_nand_d1",
- "emmc_nand_d2",
- "emmc_nand_d3",
- "emmc_nand_d4",
- "emmc_nand_d5",
- "emmc_nand_d6",
- "emmc_nand_d7",
- "emmc_cmd";
- function = "emmc";
- bias-pull-up;
- drive-strength-microamp = <4000>;
- };
-
- mux-1 {
- groups = "emmc_clk";
- function = "emmc";
- bias-disable;
- drive-strength-microamp = <4000>;
- };
- };
-
- emmc_ds_pins: emmc-ds {
- mux {
- groups = "emmc_nand_ds";
- function = "emmc";
- bias-pull-down;
- drive-strength-microamp = <4000>;
- };
- };
-
- emmc_clk_gate_pins: emmc_clk_gate {
- mux {
- groups = "BOOT_8";
- function = "gpio_periphs";
- bias-pull-down;
- drive-strength-microamp = <4000>;
- };
- };
-
- hdmitx_ddc_pins: hdmitx_ddc {
- mux {
- groups = "hdmitx_sda",
- "hdmitx_sck";
- function = "hdmitx";
- bias-disable;
- drive-strength-microamp = <4000>;
- };
- };
-
- hdmitx_hpd_pins: hdmitx_hpd {
- mux {
- groups = "hdmitx_hpd_in";
- function = "hdmitx";
- bias-disable;
- };
- };
-
-
- i2c0_sda_c_pins: i2c0-sda-c {
- mux {
- groups = "i2c0_sda_c";
- function = "i2c0";
- bias-disable;
- drive-strength-microamp = <3000>;
-
- };
- };
-
- i2c0_sck_c_pins: i2c0-sck-c {
- mux {
- groups = "i2c0_sck_c";
- function = "i2c0";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c0_sda_z0_pins: i2c0-sda-z0 {
- mux {
- groups = "i2c0_sda_z0";
- function = "i2c0";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c0_sck_z1_pins: i2c0-sck-z1 {
- mux {
- groups = "i2c0_sck_z1";
- function = "i2c0";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c0_sda_z7_pins: i2c0-sda-z7 {
- mux {
- groups = "i2c0_sda_z7";
- function = "i2c0";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c0_sda_z8_pins: i2c0-sda-z8 {
- mux {
- groups = "i2c0_sda_z8";
- function = "i2c0";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c1_sda_x_pins: i2c1-sda-x {
- mux {
- groups = "i2c1_sda_x";
- function = "i2c1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c1_sck_x_pins: i2c1-sck-x {
- mux {
- groups = "i2c1_sck_x";
- function = "i2c1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c1_sda_h2_pins: i2c1-sda-h2 {
- mux {
- groups = "i2c1_sda_h2";
- function = "i2c1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c1_sck_h3_pins: i2c1-sck-h3 {
- mux {
- groups = "i2c1_sck_h3";
- function = "i2c1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c1_sda_h6_pins: i2c1-sda-h6 {
- mux {
- groups = "i2c1_sda_h6";
- function = "i2c1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c1_sck_h7_pins: i2c1-sck-h7 {
- mux {
- groups = "i2c1_sck_h7";
- function = "i2c1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c2_sda_x_pins: i2c2-sda-x {
- mux {
- groups = "i2c2_sda_x";
- function = "i2c2";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c2_sck_x_pins: i2c2-sck-x {
- mux {
- groups = "i2c2_sck_x";
- function = "i2c2";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c2_sda_z_pins: i2c2-sda-z {
- mux {
- groups = "i2c2_sda_z";
- function = "i2c2";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c2_sck_z_pins: i2c2-sck-z {
- mux {
- groups = "i2c2_sck_z";
- function = "i2c2";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c3_sda_h_pins: i2c3-sda-h {
- mux {
- groups = "i2c3_sda_h";
- function = "i2c3";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c3_sck_h_pins: i2c3-sck-h {
- mux {
- groups = "i2c3_sck_h";
- function = "i2c3";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c3_sda_a_pins: i2c3-sda-a {
- mux {
- groups = "i2c3_sda_a";
- function = "i2c3";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c3_sck_a_pins: i2c3-sck-a {
- mux {
- groups = "i2c3_sck_a";
- function = "i2c3";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- mclk0_a_pins: mclk0-a {
- mux {
- groups = "mclk0_a";
- function = "mclk0";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- mclk1_a_pins: mclk1-a {
- mux {
- groups = "mclk1_a";
- function = "mclk1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- mclk1_x_pins: mclk1-x {
- mux {
- groups = "mclk1_x";
- function = "mclk1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- mclk1_z_pins: mclk1-z {
- mux {
- groups = "mclk1_z";
- function = "mclk1";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- pdm_din0_a_pins: pdm-din0-a {
- mux {
- groups = "pdm_din0_a";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din0_c_pins: pdm-din0-c {
- mux {
- groups = "pdm_din0_c";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din0_x_pins: pdm-din0-x {
- mux {
- groups = "pdm_din0_x";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din0_z_pins: pdm-din0-z {
- mux {
- groups = "pdm_din0_z";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din1_a_pins: pdm-din1-a {
- mux {
- groups = "pdm_din1_a";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din1_c_pins: pdm-din1-c {
- mux {
- groups = "pdm_din1_c";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din1_x_pins: pdm-din1-x {
- mux {
- groups = "pdm_din1_x";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din1_z_pins: pdm-din1-z {
- mux {
- groups = "pdm_din1_z";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din2_a_pins: pdm-din2-a {
- mux {
- groups = "pdm_din2_a";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din2_c_pins: pdm-din2-c {
- mux {
- groups = "pdm_din2_c";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din2_x_pins: pdm-din2-x {
- mux {
- groups = "pdm_din2_x";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din2_z_pins: pdm-din2-z {
- mux {
- groups = "pdm_din2_z";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din3_a_pins: pdm-din3-a {
- mux {
- groups = "pdm_din3_a";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din3_c_pins: pdm-din3-c {
- mux {
- groups = "pdm_din3_c";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din3_x_pins: pdm-din3-x {
- mux {
- groups = "pdm_din3_x";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_din3_z_pins: pdm-din3-z {
- mux {
- groups = "pdm_din3_z";
- function = "pdm";
- bias-disable;
- };
- };
-
- pdm_dclk_a_pins: pdm-dclk-a {
- mux {
- groups = "pdm_dclk_a";
- function = "pdm";
- bias-disable;
- drive-strength-microamp = <500>;
- };
- };
-
- pdm_dclk_c_pins: pdm-dclk-c {
- mux {
- groups = "pdm_dclk_c";
- function = "pdm";
- bias-disable;
- drive-strength-microamp = <500>;
- };
- };
-
- pdm_dclk_x_pins: pdm-dclk-x {
- mux {
- groups = "pdm_dclk_x";
- function = "pdm";
- bias-disable;
- drive-strength-microamp = <500>;
- };
- };
-
- pdm_dclk_z_pins: pdm-dclk-z {
- mux {
- groups = "pdm_dclk_z";
- function = "pdm";
- bias-disable;
- drive-strength-microamp = <500>;
- };
- };
-
- pwm_a_pins: pwm-a {
- mux {
- groups = "pwm_a";
- function = "pwm_a";
- bias-disable;
- };
- };
-
- pwm_b_x7_pins: pwm-b-x7 {
- mux {
- groups = "pwm_b_x7";
- function = "pwm_b";
- bias-disable;
- };
- };
-
- pwm_b_x19_pins: pwm-b-x19 {
- mux {
- groups = "pwm_b_x19";
- function = "pwm_b";
- bias-disable;
- };
- };
-
- pwm_c_c_pins: pwm-c-c {
- mux {
- groups = "pwm_c_c";
- function = "pwm_c";
- bias-disable;
- };
- };
-
- pwm_c_x5_pins: pwm-c-x5 {
- mux {
- groups = "pwm_c_x5";
- function = "pwm_c";
- bias-disable;
- };
- };
-
- pwm_c_x8_pins: pwm-c-x8 {
- mux {
- groups = "pwm_c_x8";
- function = "pwm_c";
- bias-disable;
- };
- };
-
- pwm_d_x3_pins: pwm-d-x3 {
- mux {
- groups = "pwm_d_x3";
- function = "pwm_d";
- bias-disable;
- };
- };
-
- pwm_d_x6_pins: pwm-d-x6 {
- mux {
- groups = "pwm_d_x6";
- function = "pwm_d";
- bias-disable;
- };
- };
-
- pwm_e_pins: pwm-e {
- mux {
- groups = "pwm_e";
- function = "pwm_e";
- bias-disable;
- };
- };
-
- pwm_f_x_pins: pwm-f-x {
- mux {
- groups = "pwm_f_x";
- function = "pwm_f";
- bias-disable;
- };
- };
-
- pwm_f_h_pins: pwm-f-h {
- mux {
- groups = "pwm_f_h";
- function = "pwm_f";
- bias-disable;
- };
- };
-
- sdcard_c_pins: sdcard_c {
- mux-0 {
- groups = "sdcard_d0_c",
- "sdcard_d1_c",
- "sdcard_d2_c",
- "sdcard_d3_c",
- "sdcard_cmd_c";
- function = "sdcard";
- bias-pull-up;
- drive-strength-microamp = <4000>;
- };
-
- mux-1 {
- groups = "sdcard_clk_c";
- function = "sdcard";
- bias-disable;
- drive-strength-microamp = <4000>;
- };
- };
-
- sdcard_clk_gate_c_pins: sdcard_clk_gate_c {
- mux {
- groups = "GPIOC_4";
- function = "gpio_periphs";
- bias-pull-down;
- drive-strength-microamp = <4000>;
- };
- };
-
- sdcard_z_pins: sdcard_z {
- mux-0 {
- groups = "sdcard_d0_z",
- "sdcard_d1_z",
- "sdcard_d2_z",
- "sdcard_d3_z",
- "sdcard_cmd_z";
- function = "sdcard";
- bias-pull-up;
- drive-strength-microamp = <4000>;
- };
-
- mux-1 {
- groups = "sdcard_clk_z";
- function = "sdcard";
- bias-disable;
- drive-strength-microamp = <4000>;
- };
- };
-
- sdcard_clk_gate_z_pins: sdcard_clk_gate_z {
- mux {
- groups = "GPIOZ_6";
- function = "gpio_periphs";
- bias-pull-down;
- drive-strength-microamp = <4000>;
- };
- };
-
- sdio_pins: sdio {
- mux {
- groups = "sdio_d0",
- "sdio_d1",
- "sdio_d2",
- "sdio_d3",
- "sdio_clk",
- "sdio_cmd";
- function = "sdio";
- bias-disable;
- drive-strength-microamp = <4000>;
- };
- };
-
- sdio_clk_gate_pins: sdio_clk_gate {
- mux {
- groups = "GPIOX_4";
- function = "gpio_periphs";
- bias-pull-down;
- drive-strength-microamp = <4000>;
- };
- };
-
- spdif_in_a10_pins: spdif-in-a10 {
- mux {
- groups = "spdif_in_a10";
- function = "spdif_in";
- bias-disable;
- };
- };
-
- spdif_in_a12_pins: spdif-in-a12 {
- mux {
- groups = "spdif_in_a12";
- function = "spdif_in";
- bias-disable;
- };
- };
-
- spdif_in_h_pins: spdif-in-h {
- mux {
- groups = "spdif_in_h";
- function = "spdif_in";
- bias-disable;
- };
- };
-
- spdif_out_h_pins: spdif-out-h {
- mux {
- groups = "spdif_out_h";
- function = "spdif_out";
- drive-strength-microamp = <500>;
- bias-disable;
- };
- };
-
- spdif_out_a11_pins: spdif-out-a11 {
- mux {
- groups = "spdif_out_a11";
- function = "spdif_out";
- drive-strength-microamp = <500>;
- bias-disable;
- };
- };
-
- spdif_out_a13_pins: spdif-out-a13 {
- mux {
- groups = "spdif_out_a13";
- function = "spdif_out";
- drive-strength-microamp = <500>;
- bias-disable;
- };
- };
-
- tdm_a_din0_pins: tdm-a-din0 {
- mux {
- groups = "tdm_a_din0";
- function = "tdm_a";
- bias-disable;
- };
- };
-
-
- tdm_a_din1_pins: tdm-a-din1 {
- mux {
- groups = "tdm_a_din1";
- function = "tdm_a";
- bias-disable;
- };
- };
-
- tdm_a_dout0_pins: tdm-a-dout0 {
- mux {
- groups = "tdm_a_dout0";
- function = "tdm_a";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_a_dout1_pins: tdm-a-dout1 {
- mux {
- groups = "tdm_a_dout1";
- function = "tdm_a";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_a_fs_pins: tdm-a-fs {
- mux {
- groups = "tdm_a_fs";
- function = "tdm_a";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_a_sclk_pins: tdm-a-sclk {
- mux {
- groups = "tdm_a_sclk";
- function = "tdm_a";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_a_slv_fs_pins: tdm-a-slv-fs {
- mux {
- groups = "tdm_a_slv_fs";
- function = "tdm_a";
- bias-disable;
- };
- };
-
-
- tdm_a_slv_sclk_pins: tdm-a-slv-sclk {
- mux {
- groups = "tdm_a_slv_sclk";
- function = "tdm_a";
- bias-disable;
- };
- };
-
- tdm_b_din0_pins: tdm-b-din0 {
- mux {
- groups = "tdm_b_din0";
- function = "tdm_b";
- bias-disable;
- };
- };
-
- tdm_b_din1_pins: tdm-b-din1 {
- mux {
- groups = "tdm_b_din1";
- function = "tdm_b";
- bias-disable;
- };
- };
-
- tdm_b_din2_pins: tdm-b-din2 {
- mux {
- groups = "tdm_b_din2";
- function = "tdm_b";
- bias-disable;
- };
- };
-
- tdm_b_din3_a_pins: tdm-b-din3-a {
- mux {
- groups = "tdm_b_din3_a";
- function = "tdm_b";
- bias-disable;
- };
- };
-
- tdm_b_din3_h_pins: tdm-b-din3-h {
- mux {
- groups = "tdm_b_din3_h";
- function = "tdm_b";
- bias-disable;
- };
- };
-
- tdm_b_dout0_pins: tdm-b-dout0 {
- mux {
- groups = "tdm_b_dout0";
- function = "tdm_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_b_dout1_pins: tdm-b-dout1 {
- mux {
- groups = "tdm_b_dout1";
- function = "tdm_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_b_dout2_pins: tdm-b-dout2 {
- mux {
- groups = "tdm_b_dout2";
- function = "tdm_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_b_dout3_a_pins: tdm-b-dout3-a {
- mux {
- groups = "tdm_b_dout3_a";
- function = "tdm_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_b_dout3_h_pins: tdm-b-dout3-h {
- mux {
- groups = "tdm_b_dout3_h";
- function = "tdm_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_b_fs_pins: tdm-b-fs {
- mux {
- groups = "tdm_b_fs";
- function = "tdm_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_b_sclk_pins: tdm-b-sclk {
- mux {
- groups = "tdm_b_sclk";
- function = "tdm_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_b_slv_fs_pins: tdm-b-slv-fs {
- mux {
- groups = "tdm_b_slv_fs";
- function = "tdm_b";
- bias-disable;
- };
- };
-
- tdm_b_slv_sclk_pins: tdm-b-slv-sclk {
- mux {
- groups = "tdm_b_slv_sclk";
- function = "tdm_b";
- bias-disable;
- };
- };
-
- tdm_c_din0_a_pins: tdm-c-din0-a {
- mux {
- groups = "tdm_c_din0_a";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_din0_z_pins: tdm-c-din0-z {
- mux {
- groups = "tdm_c_din0_z";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_din1_a_pins: tdm-c-din1-a {
- mux {
- groups = "tdm_c_din1_a";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_din1_z_pins: tdm-c-din1-z {
- mux {
- groups = "tdm_c_din1_z";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_din2_a_pins: tdm-c-din2-a {
- mux {
- groups = "tdm_c_din2_a";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- eth_leds_pins: eth-leds {
- mux {
- groups = "eth_link_led",
- "eth_act_led";
- function = "eth";
- bias-disable;
- };
- };
-
- eth_pins: eth {
- mux {
- groups = "eth_mdio",
- "eth_mdc",
- "eth_rgmii_rx_clk",
- "eth_rx_dv",
- "eth_rxd0",
- "eth_rxd1",
- "eth_txen",
- "eth_txd0",
- "eth_txd1";
- function = "eth";
- drive-strength-microamp = <4000>;
- bias-disable;
- };
- };
-
- eth_rgmii_pins: eth-rgmii {
- mux {
- groups = "eth_rxd2_rgmii",
- "eth_rxd3_rgmii",
- "eth_rgmii_tx_clk",
- "eth_txd2_rgmii",
- "eth_txd3_rgmii";
- function = "eth";
- drive-strength-microamp = <4000>;
- bias-disable;
- };
- };
-
- tdm_c_din2_z_pins: tdm-c-din2-z {
- mux {
- groups = "tdm_c_din2_z";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_din3_a_pins: tdm-c-din3-a {
- mux {
- groups = "tdm_c_din3_a";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_din3_z_pins: tdm-c-din3-z {
- mux {
- groups = "tdm_c_din3_z";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_dout0_a_pins: tdm-c-dout0-a {
- mux {
- groups = "tdm_c_dout0_a";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_dout0_z_pins: tdm-c-dout0-z {
- mux {
- groups = "tdm_c_dout0_z";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_dout1_a_pins: tdm-c-dout1-a {
- mux {
- groups = "tdm_c_dout1_a";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_dout1_z_pins: tdm-c-dout1-z {
- mux {
- groups = "tdm_c_dout1_z";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_dout2_a_pins: tdm-c-dout2-a {
- mux {
- groups = "tdm_c_dout2_a";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_dout2_z_pins: tdm-c-dout2-z {
- mux {
- groups = "tdm_c_dout2_z";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_dout3_a_pins: tdm-c-dout3-a {
- mux {
- groups = "tdm_c_dout3_a";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_dout3_z_pins: tdm-c-dout3-z {
- mux {
- groups = "tdm_c_dout3_z";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_fs_a_pins: tdm-c-fs-a {
- mux {
- groups = "tdm_c_fs_a";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_fs_z_pins: tdm-c-fs-z {
- mux {
- groups = "tdm_c_fs_z";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_sclk_a_pins: tdm-c-sclk-a {
- mux {
- groups = "tdm_c_sclk_a";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_sclk_z_pins: tdm-c-sclk-z {
- mux {
- groups = "tdm_c_sclk_z";
- function = "tdm_c";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_c_slv_fs_a_pins: tdm-c-slv-fs-a {
- mux {
- groups = "tdm_c_slv_fs_a";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_slv_fs_z_pins: tdm-c-slv-fs-z {
- mux {
- groups = "tdm_c_slv_fs_z";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_slv_sclk_a_pins: tdm-c-slv-sclk-a {
- mux {
- groups = "tdm_c_slv_sclk_a";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- tdm_c_slv_sclk_z_pins: tdm-c-slv-sclk-z {
- mux {
- groups = "tdm_c_slv_sclk_z";
- function = "tdm_c";
- bias-disable;
- };
- };
-
- uart_a_pins: uart-a {
- mux {
- groups = "uart_a_tx",
- "uart_a_rx";
- function = "uart_a";
- bias-disable;
- };
- };
-
- uart_a_cts_rts_pins: uart-a-cts-rts {
- mux {
- groups = "uart_a_cts",
- "uart_a_rts";
- function = "uart_a";
- bias-disable;
- };
- };
-
- uart_b_pins: uart-b {
- mux {
- groups = "uart_b_tx",
- "uart_b_rx";
- function = "uart_b";
- bias-disable;
- };
- };
-
- uart_c_pins: uart-c {
- mux {
- groups = "uart_c_tx",
- "uart_c_rx";
- function = "uart_c";
- bias-disable;
- };
- };
-
- uart_c_cts_rts_pins: uart-c-cts-rts {
- mux {
- groups = "uart_c_cts",
- "uart_c_rts";
- function = "uart_c";
- bias-disable;
- };
- };
- };
- };
-
- usb2_phy0: phy@36000 {
- compatible = "amlogic,g12a-usb2-phy";
- reg = <0x0 0x36000 0x0 0x2000>;
- clocks = <&xtal>;
- clock-names = "xtal";
- resets = <&reset RESET_USB_PHY20>;
- reset-names = "phy";
- #phy-cells = <0>;
- };
-
- dmc: bus@38000 {
- compatible = "simple-bus";
- reg = <0x0 0x38000 0x0 0x400>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>;
-
- canvas: video-lut@48 {
- compatible = "amlogic,canvas";
- reg = <0x0 0x48 0x0 0x14>;
- };
- };
-
- usb2_phy1: phy@3a000 {
- compatible = "amlogic,g12a-usb2-phy";
- reg = <0x0 0x3a000 0x0 0x2000>;
- clocks = <&xtal>;
- clock-names = "xtal";
- resets = <&reset RESET_USB_PHY21>;
- reset-names = "phy";
- #phy-cells = <0>;
- };
-
- hiu: bus@3c000 {
- compatible = "simple-bus";
- reg = <0x0 0x3c000 0x0 0x1400>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0x3c000 0x0 0x1400>;
-
- hhi: system-controller@0 {
- compatible = "amlogic,meson-gx-hhi-sysctrl",
- "simple-mfd", "syscon";
- reg = <0 0 0 0x400>;
-
- clkc: clock-controller {
- compatible = "amlogic,g12a-clkc";
- #clock-cells = <1>;
- clocks = <&xtal>;
- clock-names = "xtal";
- };
- };
- };
-
- pdm: audio-controller@40000 {
- compatible = "amlogic,g12a-pdm",
- "amlogic,axg-pdm";
- reg = <0x0 0x40000 0x0 0x34>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "PDM";
- clocks = <&clkc_audio AUD_CLKID_PDM>,
- <&clkc_audio AUD_CLKID_PDM_DCLK>,
- <&clkc_audio AUD_CLKID_PDM_SYSCLK>;
- clock-names = "pclk", "dclk", "sysclk";
- status = "disabled";
- };
-
- audio: bus@42000 {
- compatible = "simple-bus";
- reg = <0x0 0x42000 0x0 0x2000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0x42000 0x0 0x2000>;
-
- clkc_audio: clock-controller@0 {
- status = "disabled";
- compatible = "amlogic,g12a-audio-clkc";
- reg = <0x0 0x0 0x0 0xb4>;
- #clock-cells = <1>;
-
- clocks = <&clkc CLKID_AUDIO>,
- <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>,
- <&clkc CLKID_MPLL2>,
- <&clkc CLKID_MPLL3>,
- <&clkc CLKID_HIFI_PLL>,
- <&clkc CLKID_FCLK_DIV3>,
- <&clkc CLKID_FCLK_DIV4>,
- <&clkc CLKID_GP0_PLL>;
- clock-names = "pclk",
- "mst_in0",
- "mst_in1",
- "mst_in2",
- "mst_in3",
- "mst_in4",
- "mst_in5",
- "mst_in6",
- "mst_in7";
-
- resets = <&reset RESET_AUDIO>;
- };
-
- toddr_a: audio-controller@100 {
- compatible = "amlogic,g12a-toddr",
- "amlogic,axg-toddr";
- reg = <0x0 0x100 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "TODDR_A";
- interrupts = <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_TODDR_A>;
- resets = <&arb AXG_ARB_TODDR_A>;
- status = "disabled";
- };
-
- toddr_b: audio-controller@140 {
- compatible = "amlogic,g12a-toddr",
- "amlogic,axg-toddr";
- reg = <0x0 0x140 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "TODDR_B";
- interrupts = <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_TODDR_B>;
- resets = <&arb AXG_ARB_TODDR_B>;
- status = "disabled";
- };
-
- toddr_c: audio-controller@180 {
- compatible = "amlogic,g12a-toddr",
- "amlogic,axg-toddr";
- reg = <0x0 0x180 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "TODDR_C";
- interrupts = <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_TODDR_C>;
- resets = <&arb AXG_ARB_TODDR_C>;
- status = "disabled";
- };
-
- frddr_a: audio-controller@1c0 {
- compatible = "amlogic,g12a-frddr",
- "amlogic,axg-frddr";
- reg = <0x0 0x1c0 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "FRDDR_A";
- interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
- resets = <&arb AXG_ARB_FRDDR_A>;
- status = "disabled";
- };
-
- frddr_b: audio-controller@200 {
- compatible = "amlogic,g12a-frddr",
- "amlogic,axg-frddr";
- reg = <0x0 0x200 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "FRDDR_B";
- interrupts = <GIC_SPI 153 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_FRDDR_B>;
- resets = <&arb AXG_ARB_FRDDR_B>;
- status = "disabled";
- };
-
- frddr_c: audio-controller@240 {
- compatible = "amlogic,g12a-frddr",
- "amlogic,axg-frddr";
- reg = <0x0 0x240 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "FRDDR_C";
- interrupts = <GIC_SPI 154 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_FRDDR_C>;
- resets = <&arb AXG_ARB_FRDDR_C>;
- status = "disabled";
- };
-
- arb: reset-controller@280 {
- status = "disabled";
- compatible = "amlogic,meson-axg-audio-arb";
- reg = <0x0 0x280 0x0 0x4>;
- #reset-cells = <1>;
- clocks = <&clkc_audio AUD_CLKID_DDR_ARB>;
- };
-
- tdmin_a: audio-controller@300 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x300 0x0 0x40>;
- sound-name-prefix = "TDMIN_A";
- clocks = <&clkc_audio AUD_CLKID_TDMIN_A>,
- <&clkc_audio AUD_CLKID_TDMIN_A_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_A_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmin_b: audio-controller@340 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x340 0x0 0x40>;
- sound-name-prefix = "TDMIN_B";
- clocks = <&clkc_audio AUD_CLKID_TDMIN_B>,
- <&clkc_audio AUD_CLKID_TDMIN_B_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_B_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmin_c: audio-controller@380 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x380 0x0 0x40>;
- sound-name-prefix = "TDMIN_C";
- clocks = <&clkc_audio AUD_CLKID_TDMIN_C>,
- <&clkc_audio AUD_CLKID_TDMIN_C_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_C_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmin_lb: audio-controller@3c0 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x3c0 0x0 0x40>;
- sound-name-prefix = "TDMIN_LB";
- clocks = <&clkc_audio AUD_CLKID_TDMIN_LB>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- spdifin: audio-controller@400 {
- compatible = "amlogic,g12a-spdifin",
- "amlogic,axg-spdifin";
- reg = <0x0 0x400 0x0 0x30>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "SPDIFIN";
- interrupts = <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
- <&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
- clock-names = "pclk", "refclk";
- status = "disabled";
- };
-
- spdifout: audio-controller@480 {
- compatible = "amlogic,g12a-spdifout",
- "amlogic,axg-spdifout";
- reg = <0x0 0x480 0x0 0x50>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "SPDIFOUT";
- clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
- <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
- clock-names = "pclk", "mclk";
- status = "disabled";
- };
-
- tdmout_a: audio-controller@500 {
- compatible = "amlogic,g12a-tdmout";
- reg = <0x0 0x500 0x0 0x40>;
- sound-name-prefix = "TDMOUT_A";
- clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmout_b: audio-controller@540 {
- compatible = "amlogic,g12a-tdmout";
- reg = <0x0 0x540 0x0 0x40>;
- sound-name-prefix = "TDMOUT_B";
- clocks = <&clkc_audio AUD_CLKID_TDMOUT_B>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmout_c: audio-controller@580 {
- compatible = "amlogic,g12a-tdmout";
- reg = <0x0 0x580 0x0 0x40>;
- sound-name-prefix = "TDMOUT_C";
- clocks = <&clkc_audio AUD_CLKID_TDMOUT_C>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- spdifout_b: audio-controller@680 {
- compatible = "amlogic,g12a-spdifout",
- "amlogic,axg-spdifout";
- reg = <0x0 0x680 0x0 0x50>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "SPDIFOUT_B";
- clocks = <&clkc_audio AUD_CLKID_SPDIFOUT_B>,
- <&clkc_audio AUD_CLKID_SPDIFOUT_B_CLK>;
- clock-names = "pclk", "mclk";
- status = "disabled";
- };
-
- tohdmitx: audio-controller@744 {
- compatible = "amlogic,g12a-tohdmitx";
- reg = <0x0 0x744 0x0 0x4>;
- #sound-dai-cells = <1>;
- sound-name-prefix = "TOHDMITX";
- status = "disabled";
- };
- };
-
- usb3_pcie_phy: phy@46000 {
- compatible = "amlogic,g12a-usb3-pcie-phy";
- reg = <0x0 0x46000 0x0 0x2000>;
- clocks = <&clkc CLKID_PCIE_PLL>;
- clock-names = "ref_clk";
- resets = <&reset RESET_PCIE_PHY>;
- reset-names = "phy";
- assigned-clocks = <&clkc CLKID_PCIE_PLL>;
- assigned-clock-rates = <100000000>;
- #phy-cells = <1>;
- };
-
- eth_phy: mdio-multiplexer@4c000 {
- compatible = "amlogic,g12a-mdio-mux";
- reg = <0x0 0x4c000 0x0 0xa4>;
- clocks = <&clkc CLKID_ETH_PHY>,
- <&xtal>,
- <&clkc CLKID_MPLL_50M>;
- clock-names = "pclk", "clkin0", "clkin1";
- mdio-parent-bus = <&mdio0>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- ext_mdio: mdio@0 {
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- int_mdio: mdio@1 {
- reg = <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- internal_ephy: ethernet_phy@8 {
- compatible = "ethernet-phy-id0180.3301",
- "ethernet-phy-ieee802.3-c22";
- interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
- reg = <8>;
- max-speed = <100>;
- };
- };
- };
- };
-
- aobus: bus@ff800000 {
- compatible = "simple-bus";
- reg = <0x0 0xff800000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
-
- rti: sys-ctrl@0 {
- compatible = "amlogic,meson-gx-ao-sysctrl",
- "simple-mfd", "syscon";
- reg = <0x0 0x0 0x0 0x100>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0x0 0x0 0x100>;
-
- clkc_AO: clock-controller {
- compatible = "amlogic,meson-g12a-aoclkc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- clocks = <&xtal>, <&clkc CLKID_CLK81>;
- clock-names = "xtal", "mpeg-clk";
- };
-
- pwrc_vpu: power-controller-vpu {
- compatible = "amlogic,meson-g12a-pwrc-vpu";
- #power-domain-cells = <0>;
- amlogic,hhi-sysctrl = <&hhi>;
- resets = <&reset RESET_VIU>,
- <&reset RESET_VENC>,
- <&reset RESET_VCBUS>,
- <&reset RESET_BT656>,
- <&reset RESET_RDMA>,
- <&reset RESET_VENCI>,
- <&reset RESET_VENCP>,
- <&reset RESET_VDAC>,
- <&reset RESET_VDI6>,
- <&reset RESET_VENCL>,
- <&reset RESET_VID_LOCK>;
- clocks = <&clkc CLKID_VPU>,
- <&clkc CLKID_VAPB>;
- clock-names = "vpu", "vapb";
- /*
- * VPU clocking is provided by two identical clock paths
- * VPU_0 and VPU_1 muxed to a single clock by a glitch
- * free mux to safely change frequency while running.
- * Same for VAPB but with a final gate after the glitch free mux.
- */
- assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
- <&clkc CLKID_VPU_0>,
- <&clkc CLKID_VPU>, /* Glitch free mux */
- <&clkc CLKID_VAPB_0_SEL>,
- <&clkc CLKID_VAPB_0>,
- <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
- assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
- <0>, /* Do Nothing */
- <&clkc CLKID_VPU_0>,
- <&clkc CLKID_FCLK_DIV4>,
- <0>, /* Do Nothing */
- <&clkc CLKID_VAPB_0>;
- assigned-clock-rates = <0>, /* Do Nothing */
- <666666666>,
- <0>, /* Do Nothing */
- <0>, /* Do Nothing */
- <250000000>,
- <0>; /* Do Nothing */
- };
-
- ao_pinctrl: pinctrl@14 {
- compatible = "amlogic,meson-g12a-aobus-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio_ao: bank@14 {
- reg = <0x0 0x14 0x0 0x8>,
- <0x0 0x1c 0x0 0x8>,
- <0x0 0x24 0x0 0x14>;
- reg-names = "mux",
- "ds",
- "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&ao_pinctrl 0 0 15>;
- };
-
- i2c_ao_sck_pins: i2c_ao_sck_pins {
- mux {
- groups = "i2c_ao_sck";
- function = "i2c_ao";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c_ao_sda_pins: i2c_ao_sda {
- mux {
- groups = "i2c_ao_sda";
- function = "i2c_ao";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c_ao_sck_e_pins: i2c_ao_sck_e {
- mux {
- groups = "i2c_ao_sck_e";
- function = "i2c_ao";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- i2c_ao_sda_e_pins: i2c_ao_sda_e {
- mux {
- groups = "i2c_ao_sda_e";
- function = "i2c_ao";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- mclk0_ao_pins: mclk0-ao {
- mux {
- groups = "mclk0_ao";
- function = "mclk0_ao";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_ao_b_din0_pins: tdm-ao-b-din0 {
- mux {
- groups = "tdm_ao_b_din0";
- function = "tdm_ao_b";
- bias-disable;
- };
- };
-
- spdif_ao_out_pins: spdif-ao-out {
- mux {
- groups = "spdif_ao_out";
- function = "spdif_ao_out";
- drive-strength-microamp = <500>;
- bias-disable;
- };
- };
-
- tdm_ao_b_din1_pins: tdm-ao-b-din1 {
- mux {
- groups = "tdm_ao_b_din1";
- function = "tdm_ao_b";
- bias-disable;
- };
- };
-
- tdm_ao_b_din2_pins: tdm-ao-b-din2 {
- mux {
- groups = "tdm_ao_b_din2";
- function = "tdm_ao_b";
- bias-disable;
- };
- };
-
- tdm_ao_b_dout0_pins: tdm-ao-b-dout0 {
- mux {
- groups = "tdm_ao_b_dout0";
- function = "tdm_ao_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_ao_b_dout1_pins: tdm-ao-b-dout1 {
- mux {
- groups = "tdm_ao_b_dout1";
- function = "tdm_ao_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_ao_b_dout2_pins: tdm-ao-b-dout2 {
- mux {
- groups = "tdm_ao_b_dout2";
- function = "tdm_ao_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_ao_b_fs_pins: tdm-ao-b-fs {
- mux {
- groups = "tdm_ao_b_fs";
- function = "tdm_ao_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_ao_b_sclk_pins: tdm-ao-b-sclk {
- mux {
- groups = "tdm_ao_b_sclk";
- function = "tdm_ao_b";
- bias-disable;
- drive-strength-microamp = <3000>;
- };
- };
-
- tdm_ao_b_slv_fs_pins: tdm-ao-b-slv-fs {
- mux {
- groups = "tdm_ao_b_slv_fs";
- function = "tdm_ao_b";
- bias-disable;
- };
- };
-
- tdm_ao_b_slv_sclk_pins: tdm-ao-b-slv-sclk {
- mux {
- groups = "tdm_ao_b_slv_sclk";
- function = "tdm_ao_b";
- bias-disable;
- };
- };
-
- uart_ao_a_pins: uart-a-ao {
- mux {
- groups = "uart_ao_a_tx",
- "uart_ao_a_rx";
- function = "uart_ao_a";
- bias-disable;
- };
- };
-
- uart_ao_a_cts_rts_pins: uart-ao-a-cts-rts {
- mux {
- groups = "uart_ao_a_cts",
- "uart_ao_a_rts";
- function = "uart_ao_a";
- bias-disable;
- };
- };
-
- pwm_ao_a_pins: pwm-ao-a {
- mux {
- groups = "pwm_ao_a";
- function = "pwm_ao_a";
- bias-disable;
- };
- };
-
- pwm_ao_b_pins: pwm-ao-b {
- mux {
- groups = "pwm_ao_b";
- function = "pwm_ao_b";
- bias-disable;
- };
- };
-
- pwm_ao_c_4_pins: pwm-ao-c-4 {
- mux {
- groups = "pwm_ao_c_4";
- function = "pwm_ao_c";
- bias-disable;
- };
- };
-
- pwm_ao_c_6_pins: pwm-ao-c-6 {
- mux {
- groups = "pwm_ao_c_6";
- function = "pwm_ao_c";
- bias-disable;
- };
- };
-
- pwm_ao_d_5_pins: pwm-ao-d-5 {
- mux {
- groups = "pwm_ao_d_5";
- function = "pwm_ao_d";
- bias-disable;
- };
- };
-
- pwm_ao_d_10_pins: pwm-ao-d-10 {
- mux {
- groups = "pwm_ao_d_10";
- function = "pwm_ao_d";
- bias-disable;
- };
- };
-
- pwm_ao_d_e_pins: pwm-ao-d-e {
- mux {
- groups = "pwm_ao_d_e";
- function = "pwm_ao_d";
- };
- };
-
- remote_input_ao_pins: remote-input-ao {
- mux {
- groups = "remote_ao_input";
- function = "remote_ao_input";
- bias-disable;
- };
- };
- };
- };
-
- cec_AO: cec@100 {
- compatible = "amlogic,meson-gx-ao-cec";
- reg = <0x0 0x00100 0x0 0x14>;
- interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_AO CLKID_AO_CEC>;
- clock-names = "core";
- status = "disabled";
- };
-
- sec_AO: ao-secure@140 {
- compatible = "amlogic,meson-gx-ao-secure", "syscon";
- reg = <0x0 0x140 0x0 0x140>;
- amlogic,has-chip-id;
- };
-
- cecb_AO: cec@280 {
- compatible = "amlogic,meson-g12a-ao-cec";
- reg = <0x0 0x00280 0x0 0x1c>;
- interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>;
- clock-names = "oscin";
- status = "disabled";
- };
-
- pwm_AO_cd: pwm@2000 {
- compatible = "amlogic,meson-g12a-ao-pwm-cd";
- reg = <0x0 0x2000 0x0 0x20>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- uart_AO: serial@3000 {
- compatible = "amlogic,meson-gx-uart",
- "amlogic,meson-ao-uart";
- reg = <0x0 0x3000 0x0 0x18>;
- interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>, <&clkc_AO CLKID_AO_UART>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
- status = "disabled";
- };
-
- uart_AO_B: serial@4000 {
- compatible = "amlogic,meson-gx-uart",
- "amlogic,meson-ao-uart";
- reg = <0x0 0x4000 0x0 0x18>;
- interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
- status = "disabled";
- };
-
- i2c_AO: i2c@5000 {
- compatible = "amlogic,meson-axg-i2c";
- status = "disabled";
- reg = <0x0 0x05000 0x0 0x20>;
- interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clkc CLKID_I2C>;
- };
-
- pwm_AO_ab: pwm@7000 {
- compatible = "amlogic,meson-g12a-ao-pwm-ab";
- reg = <0x0 0x7000 0x0 0x20>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- ir: ir@8000 {
- compatible = "amlogic,meson-gxbb-ir";
- reg = <0x0 0x8000 0x0 0x20>;
- interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
- };
-
- saradc: adc@9000 {
- compatible = "amlogic,meson-g12a-saradc",
- "amlogic,meson-saradc";
- reg = <0x0 0x9000 0x0 0x48>;
- #io-channel-cells = <1>;
- interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>,
- <&clkc_AO CLKID_AO_SAR_ADC>,
- <&clkc_AO CLKID_AO_SAR_ADC_CLK>,
- <&clkc_AO CLKID_AO_SAR_ADC_SEL>;
- clock-names = "clkin", "core", "adc_clk", "adc_sel";
- status = "disabled";
- };
- };
-
- vpu: vpu@ff900000 {
- compatible = "amlogic,meson-g12a-vpu";
- reg = <0x0 0xff900000 0x0 0x100000>,
- <0x0 0xff63c000 0x0 0x1000>;
- reg-names = "vpu", "hhi";
- interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
- #address-cells = <1>;
- #size-cells = <0>;
- amlogic,canvas = <&canvas>;
- power-domains = <&pwrc_vpu>;
-
- /* CVBS VDAC output port */
- cvbs_vdac_port: port@0 {
- reg = <0>;
- };
-
- /* HDMI-TX output port */
- hdmi_tx_port: port@1 {
- reg = <1>;
-
- hdmi_tx_out: endpoint {
- remote-endpoint = <&hdmi_tx_in>;
- };
- };
- };
-
- gic: interrupt-controller@ffc01000 {
- compatible = "arm,gic-400";
- reg = <0x0 0xffc01000 0 0x1000>,
- <0x0 0xffc02000 0 0x2000>,
- <0x0 0xffc04000 0 0x2000>,
- <0x0 0xffc06000 0 0x2000>;
- interrupt-controller;
- interrupts = <GIC_PPI 9
- (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
- #interrupt-cells = <3>;
- #address-cells = <0>;
- };
-
- cbus: bus@ffd00000 {
- compatible = "simple-bus";
- reg = <0x0 0xffd00000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x100000>;
-
- reset: reset-controller@1004 {
- compatible = "amlogic,meson-g12a-reset",
- "amlogic,meson-axg-reset";
- reg = <0x0 0x1004 0x0 0x9c>;
- #reset-cells = <1>;
- };
-
- gpio_intc: interrupt-controller@f080 {
- compatible = "amlogic,meson-g12a-gpio-intc",
- "amlogic,meson-gpio-intc";
- reg = <0x0 0xf080 0x0 0x10>;
- interrupt-controller;
- #interrupt-cells = <2>;
- amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
- };
-
- pwm_ef: pwm@19000 {
- compatible = "amlogic,meson-g12a-ee-pwm";
- reg = <0x0 0x19000 0x0 0x20>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- pwm_cd: pwm@1a000 {
- compatible = "amlogic,meson-g12a-ee-pwm";
- reg = <0x0 0x1a000 0x0 0x20>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- pwm_ab: pwm@1b000 {
- compatible = "amlogic,meson-g12a-ee-pwm";
- reg = <0x0 0x1b000 0x0 0x20>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- i2c3: i2c@1c000 {
- compatible = "amlogic,meson-axg-i2c";
- status = "disabled";
- reg = <0x0 0x1c000 0x0 0x20>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clkc CLKID_I2C>;
- };
-
- i2c2: i2c@1d000 {
- compatible = "amlogic,meson-axg-i2c";
- status = "disabled";
- reg = <0x0 0x1d000 0x0 0x20>;
- interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clkc CLKID_I2C>;
- };
-
- i2c1: i2c@1e000 {
- compatible = "amlogic,meson-axg-i2c";
- status = "disabled";
- reg = <0x0 0x1e000 0x0 0x20>;
- interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clkc CLKID_I2C>;
- };
-
- i2c0: i2c@1f000 {
- compatible = "amlogic,meson-axg-i2c";
- status = "disabled";
- reg = <0x0 0x1f000 0x0 0x20>;
- interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&clkc CLKID_I2C>;
- };
-
- clk_msr: clock-measure@18000 {
- compatible = "amlogic,meson-g12a-clk-measure";
- reg = <0x0 0x18000 0x0 0x10>;
- };
-
- uart_C: serial@22000 {
- compatible = "amlogic,meson-gx-uart";
- reg = <0x0 0x22000 0x0 0x18>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
- status = "disabled";
- };
-
- uart_B: serial@23000 {
- compatible = "amlogic,meson-gx-uart";
- reg = <0x0 0x23000 0x0 0x18>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
- status = "disabled";
- };
-
- uart_A: serial@24000 {
- compatible = "amlogic,meson-gx-uart";
- reg = <0x0 0x24000 0x0 0x18>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
- clock-names = "xtal", "pclk", "baud";
- status = "disabled";
- };
- };
-
- sd_emmc_a: sd@ffe03000 {
- compatible = "amlogic,meson-axg-mmc";
- reg = <0x0 0xffe03000 0x0 0x800>;
- interrupts = <GIC_SPI 189 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
- clocks = <&clkc CLKID_SD_EMMC_A>,
- <&clkc CLKID_SD_EMMC_A_CLK0>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- resets = <&reset RESET_SD_EMMC_A>;
- amlogic,dram-access-quirk;
- };
-
- sd_emmc_b: sd@ffe05000 {
- compatible = "amlogic,meson-axg-mmc";
- reg = <0x0 0xffe05000 0x0 0x800>;
- interrupts = <GIC_SPI 190 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
- clocks = <&clkc CLKID_SD_EMMC_B>,
- <&clkc CLKID_SD_EMMC_B_CLK0>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- resets = <&reset RESET_SD_EMMC_B>;
- };
-
- sd_emmc_c: mmc@ffe07000 {
- compatible = "amlogic,meson-axg-mmc";
- reg = <0x0 0xffe07000 0x0 0x800>;
- interrupts = <GIC_SPI 191 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
- clocks = <&clkc CLKID_SD_EMMC_C>,
- <&clkc CLKID_SD_EMMC_C_CLK0>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- resets = <&reset RESET_SD_EMMC_C>;
- };
-
- usb: usb@ffe09000 {
- status = "disabled";
- compatible = "amlogic,meson-g12a-usb-ctrl";
- reg = <0x0 0xffe09000 0x0 0xa0>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- clocks = <&clkc CLKID_USB>;
- resets = <&reset RESET_USB>;
-
- dr_mode = "otg";
-
- phys = <&usb2_phy0>, <&usb2_phy1>,
- <&usb3_pcie_phy PHY_TYPE_USB3>;
- phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
-
- dwc2: usb@ff400000 {
- compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
- reg = <0x0 0xff400000 0x0 0x40000>;
- interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
- clock-names = "ddr";
- phys = <&usb2_phy1>;
- phy-names = "usb2-phy";
- dr_mode = "peripheral";
- g-rx-fifo-size = <192>;
- g-np-tx-fifo-size = <128>;
- g-tx-fifo-size = <128 128 16 16 16>;
- };
-
- dwc3: usb@ff500000 {
- compatible = "snps,dwc3";
- reg = <0x0 0xff500000 0x0 0x100000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- dr_mode = "host";
- snps,dis_u2_susphy_quirk;
- snps,quirk-frame-length-adjustment;
- };
- };
-
- mali: gpu@ffe40000 {
- compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost";
- reg = <0x0 0xffe40000 0x0 0x40000>;
- interrupt-parent = <&gic>;
- interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "gpu", "mmu", "job";
- clocks = <&clkc CLKID_MALI>;
- resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>;
-
- /*
- * Mali clocking is provided by two identical clock paths
- * MALI_0 and MALI_1 muxed to a single clock by a glitch
- * free mux to safely change frequency while running.
- */
- assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
- <&clkc CLKID_MALI_0>,
- <&clkc CLKID_MALI>; /* Glitch free mux */
- assigned-clock-parents = <&clkc CLKID_FCLK_DIV2P5>,
- <0>, /* Do Nothing */
- <&clkc CLKID_MALI_0>;
- assigned-clock-rates = <0>, /* Do Nothing */
- <800000000>,
- <0>; /* Do Nothing */
- };
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
- };
-
- xtal: xtal-clk {
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "xtal";
- #clock-cells = <0>;
- };
-
+&sd_emmc_a {
+ amlogic,dram-access-quirk;
};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
index 9e88e513b22d..d5edbc1a1991 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
@@ -4,12 +4,15 @@
* Author: Neil Armstrong <narmstrong@baylibre.com>
*/
-#include "meson-g12a.dtsi"
+#include "meson-g12-common.dtsi"
/ {
compatible = "amlogic,g12b";
cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
cpu-map {
cluster0 {
core0 {
@@ -40,8 +43,21 @@
};
};
- /delete-node/ cpu@2;
- /delete-node/ cpu@3;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
cpu100: cpu@100 {
device_type = "cpu";
@@ -74,9 +90,17 @@
enable-method = "psci";
next-level-cache = <&l2>;
};
+
+ l2: l2-cache0 {
+ compatible = "cache";
+ };
};
};
&clkc {
compatible = "amlogic,g12b-clkc";
};
+
+&sd_emmc_a {
+ amlogic,dram-access-quirk;
+};
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 2/6] arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
2019-07-29 13:26 ` [PATCH 1/6] arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi Neil Armstrong
@ 2019-07-29 13:26 ` Neil Armstrong
2019-07-29 13:26 ` [PATCH 3/6] arm64: dts: meson-g12a: add cpus OPP table Neil Armstrong
` (4 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Neil Armstrong @ 2019-07-29 13:26 UTC (permalink / raw)
To: khilman
Cc: Martin Blumenstingl, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
Add the ao_pinctrl subnode for the pwm_a function on GPIOE_2.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
index 06e186ca41e3..38d70ce1cfc7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -1970,6 +1970,14 @@
};
};
+ pwm_a_e_pins: pwm-a-e {
+ mux {
+ groups = "pwm_a_e";
+ function = "pwm_a_e";
+ bias-disable;
+ };
+ };
+
pwm_ao_a_pins: pwm-ao-a {
mux {
groups = "pwm_ao_a";
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 3/6] arm64: dts: meson-g12a: add cpus OPP table
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
2019-07-29 13:26 ` [PATCH 1/6] arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi Neil Armstrong
2019-07-29 13:26 ` [PATCH 2/6] arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux Neil Armstrong
@ 2019-07-29 13:26 ` Neil Armstrong
2019-07-29 13:26 ` [PATCH 4/6] arm64: dts: meson-g12a: enable DVFS on G12A boards Neil Armstrong
` (3 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Neil Armstrong @ 2019-07-29 13:26 UTC (permalink / raw)
To: khilman; +Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
Add the OPP table taken from the vendor u200 and u211 DTS.
The Amlogic G12A SoC seems to available in 3 types :
- low-speed: up to 1,8GHz
- mid-speed: up to 1,908GHz
- high-speed: up to 2.1GHz
And the S905X2 opp voltages are slightly higher than the S905D2
OPP voltages for the low-speed table.
This adds the conservative OPP table with the S905X2 higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an Amlogic U200 Reference Board,
SeiRobotics SEI510 and X96 Max Set-Top-Boxes running the arm64 cpuburn
at [1] and cycling between all the possible cpufreq translations and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 60 +++++++++++++++++++++
1 file changed, 60 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
index ac15967bb7fa..733a9d46fc4b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -48,6 +48,66 @@
compatible = "cache";
};
};
+
+ cpu_opp_table: opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-250000000 {
+ opp-hz = /bits/ 64 <250000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-667000000 {
+ opp-hz = /bits/ 64 <666666666>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-1398000000 {
+ opp-hz = /bits/ 64 <1398000000>;
+ opp-microvolt = <761000>;
+ };
+
+ opp-1512000000 {
+ opp-hz = /bits/ 64 <1512000000>;
+ opp-microvolt = <791000>;
+ };
+
+ opp-1608000000 {
+ opp-hz = /bits/ 64 <1608000000>;
+ opp-microvolt = <831000>;
+ };
+
+ opp-1704000000 {
+ opp-hz = /bits/ 64 <1704000000>;
+ opp-microvolt = <861000>;
+ };
+
+ opp-1800000000 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <981000>;
+ };
+ };
};
&sd_emmc_a {
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 4/6] arm64: dts: meson-g12a: enable DVFS on G12A boards
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
` (2 preceding siblings ...)
2019-07-29 13:26 ` [PATCH 3/6] arm64: dts: meson-g12a: add cpus OPP table Neil Armstrong
@ 2019-07-29 13:26 ` Neil Armstrong
2019-07-29 13:26 ` [PATCH 5/6] arm64: dts: meson-g12b: add cpus OPP tables Neil Armstrong
` (2 subsequent siblings)
6 siblings, 0 replies; 11+ messages in thread
From: Neil Armstrong @ 2019-07-29 13:26 UTC (permalink / raw)
To: khilman
Cc: Martin Blumenstingl, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
Enable DVFS for the U200, SEI520 and X96-Max Amlogic G12A based board
by setting the clock, OPP and supply for each CPU cores.
The CPU cluster power supply can achieve 0.73V to 1.01V using a PWM
output clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations and checking the final
frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../boot/dts/amlogic/meson-g12a-sei510.dts | 55 +++++++++++++++++++
.../boot/dts/amlogic/meson-g12a-u200.dts | 54 ++++++++++++++++++
.../boot/dts/amlogic/meson-g12a-x96-max.dts | 52 ++++++++++++++++++
3 files changed, 161 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
index 12aa7eaeaf68..c9fa23a56562 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -129,6 +129,25 @@
enable-active-high;
};
+ vddcpu: regulator-vddcpu {
+ /*
+ * SY8120B1ABC DC/DC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&dc_in>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vddio_ao1v8: regulator-vddio_ao1v8 {
compatible = "regulator-fixed";
regulator-name = "VDDIO_AO1V8";
@@ -297,6 +316,34 @@
status = "okay";
};
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
@@ -345,6 +392,14 @@
pinctrl-names = "default";
};
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
index 8551fbd4a488..2a324f0136e3 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
@@ -129,6 +129,24 @@
regulator-always-on;
};
+ vddcpu: regulator-vddcpu {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
};
&cec_AO {
@@ -145,6 +163,34 @@
hdmi-phandle = <&hdmi_tx>;
};
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
@@ -197,6 +243,14 @@
pinctrl-names = "default";
};
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
index fe4013cca876..c1e58a69d434 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
@@ -132,6 +132,22 @@
regulator-always-on;
};
+ vddcpu: regulator-vddcpu {
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&dc_in>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
sound {
compatible = "amlogic,axg-sound-card";
model = "G12A-X96-MAX";
@@ -242,6 +258,34 @@
status = "okay";
};
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
@@ -279,6 +323,14 @@
pinctrl-names = "default";
};
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
&ext_mdio {
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 5/6] arm64: dts: meson-g12b: add cpus OPP tables
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
` (3 preceding siblings ...)
2019-07-29 13:26 ` [PATCH 4/6] arm64: dts: meson-g12a: enable DVFS on G12A boards Neil Armstrong
@ 2019-07-29 13:26 ` Neil Armstrong
2019-07-29 13:26 ` [PATCH 6/6] arm64: dts: meson-g12b-odroid-n2: enable DVFS Neil Armstrong
2019-08-05 19:07 ` [PATCH 0/6] arm64: g12a: add support for DVFS Kevin Hilman
6 siblings, 0 replies; 11+ messages in thread
From: Neil Armstrong @ 2019-07-29 13:26 UTC (permalink / raw)
To: khilman; +Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
Add the OPP table taken from the HardKernel Odroid-N2 DTS.
The Amlogic G12B SoC seems to available in 2 types :
- low-speed: Cortex-A73 Cluster up to 1,704GHz
- high-speed: Cortex-A73 Cluster up to 2.208GHz
The Cortex-A73 Cluster can be clocked up to 1,896GHz for both types.
The Vendor Amlogic A311D OPP table are slighly different, with lower
voltages than the HardKernel S922X tables but seems to be high-speed type.
This adds the conservative OPP table with the S922X higher voltages
and the maximum low-speed OPP frequency.
The values were tested to be stable on an HardKernel Odroid-N2 board
running the arm64 cpuburn at [1] and cycling between all the possible
cpufreq translations for both clusters and checking the final frequency
using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 115 ++++++++++++++++++++
1 file changed, 115 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
index d5edbc1a1991..98ae8a7c8b41 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
@@ -95,6 +95,121 @@
compatible = "cache";
};
};
+
+ cpu_opp_table_0: opp-table-0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-250000000 {
+ opp-hz = /bits/ 64 <250000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-666666666 {
+ opp-hz = /bits/ 64 <666666666>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <731000>;
+ };
+
+ opp-1398000000 {
+ opp-hz = /bits/ 64 <1398000000>;
+ opp-microvolt = <761000>;
+ };
+
+ opp-1512000000 {
+ opp-hz = /bits/ 64 <1512000000>;
+ opp-microvolt = <791000>;
+ };
+
+ opp-1608000000 {
+ opp-hz = /bits/ 64 <1608000000>;
+ opp-microvolt = <831000>;
+ };
+
+ opp-1704000000 {
+ opp-hz = /bits/ 64 <1704000000>;
+ opp-microvolt = <861000>;
+ };
+
+ opp-1896000000 {
+ opp-hz = /bits/ 64 <1896000000>;
+ opp-microvolt = <981000>;
+ };
+ };
+
+ cpub_opp_table_1: opp-table-1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ opp-microvolt = <751000>;
+ };
+
+ opp-250000000 {
+ opp-hz = /bits/ 64 <250000000>;
+ opp-microvolt = <751000>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <751000>;
+ };
+
+ opp-666666666 {
+ opp-hz = /bits/ 64 <666666666>;
+ opp-microvolt = <751000>;
+ };
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <751000>;
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <771000>;
+ };
+
+ opp-1398000000 {
+ opp-hz = /bits/ 64 <1398000000>;
+ opp-microvolt = <791000>;
+ };
+
+ opp-1512000000 {
+ opp-hz = /bits/ 64 <1512000000>;
+ opp-microvolt = <821000>;
+ };
+
+ opp-1608000000 {
+ opp-hz = /bits/ 64 <1608000000>;
+ opp-microvolt = <861000>;
+ };
+
+ opp-1704000000 {
+ opp-hz = /bits/ 64 <1704000000>;
+ opp-microvolt = <891000>;
+ };
+ };
};
&clkc {
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH 6/6] arm64: dts: meson-g12b-odroid-n2: enable DVFS
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
` (4 preceding siblings ...)
2019-07-29 13:26 ` [PATCH 5/6] arm64: dts: meson-g12b: add cpus OPP tables Neil Armstrong
@ 2019-07-29 13:26 ` Neil Armstrong
2019-08-05 19:07 ` [PATCH 0/6] arm64: g12a: add support for DVFS Kevin Hilman
6 siblings, 0 replies; 11+ messages in thread
From: Neil Armstrong @ 2019-07-29 13:26 UTC (permalink / raw)
To: khilman
Cc: Martin Blumenstingl, linux-amlogic, linux-kernel,
linux-arm-kernel, Neil Armstrong
Enable DVFS for the Odroid-N2 by setting the clock, OPP and supply
for each cores of each CPU clusters.
The first cluster uses the "VDDCPU_B" power supply, and the second
cluster uses the "VDDCPU_A" power supply.
Each power supply can achieve 0.73V to 1.01V using 2 distinct PWM
outputs clocked at 800KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of each cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 96 +++++++++++++++++++
1 file changed, 96 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
index 4e916e1f71f7..777bfb938854 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts
@@ -115,6 +115,44 @@
/* FIXME: actually controlled by VDDCPU_B_EN */
};
+ vddcpu_a: regulator-vddcpu-a {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_A";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_ab 0 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddcpu_b: regulator-vddcpu-b {
+ /*
+ * Silergy SY8120B1ABC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_B";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
hub_5v: regulator-hub_5v {
compatible = "regulator-fixed";
regulator-name = "HUB_5V";
@@ -246,6 +284,48 @@
status = "okay";
};
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
&ext_mdio {
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
@@ -317,6 +397,22 @@
pinctrl-names = "default";
};
+&pwm_ab {
+ pinctrl-0 = <&pwm_a_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH 0/6] arm64: g12a: add support for DVFS
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
` (5 preceding siblings ...)
2019-07-29 13:26 ` [PATCH 6/6] arm64: dts: meson-g12b-odroid-n2: enable DVFS Neil Armstrong
@ 2019-08-05 19:07 ` Kevin Hilman
2019-08-08 23:56 ` Kevin Hilman
6 siblings, 1 reply; 11+ messages in thread
From: Kevin Hilman @ 2019-08-05 19:07 UTC (permalink / raw)
To: Neil Armstrong
Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
Neil Armstrong <narmstrong@baylibre.com> writes:
> The G12A & G12B SoCs has kernel controllable CPU clocks and PWMs for
> voltage regulators.
>
> This patchsets moves the meson-g12a.dtsi to meson-g12-common.dtsi to simplify
> handling the G12A & G12B differences in the meson-g12a.dtsi & meson-g12b.dtsi
> files, like the OPPs and CPU nodes.
>
> Then G12A & G12B OPP tables are added, followed by the CPU voltages regulators
> in each boards DT.
>
> It was voluntary chosen to enabled DVFS (CPU regulator and CPU clocks) only
> in boards, to make sure only tested boards has DVFS enabled.
>
> This patchset :
> - moves the G12A DT to a common g12a-common dtsi
> - adds the G12A and G12B OPPs
> - enables DVFS on all supported boards
>
> Dependencies:
> - None
Not quite. The last patch to enable DVFS on odroid-n2 has a build-time
dependency on the clock series that adds the CPUB clock.
I'll apply the rest of the series to v5.4/dt64 until there's a stable
clock tag I can use for the clocks.
Kevin
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 0/6] arm64: g12a: add support for DVFS
2019-08-05 19:07 ` [PATCH 0/6] arm64: g12a: add support for DVFS Kevin Hilman
@ 2019-08-08 23:56 ` Kevin Hilman
2019-08-09 18:21 ` Kevin Hilman
2019-08-12 20:54 ` Kevin Hilman
0 siblings, 2 replies; 11+ messages in thread
From: Kevin Hilman @ 2019-08-08 23:56 UTC (permalink / raw)
To: Neil Armstrong
Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
Kevin Hilman <khilman@baylibre.com> writes:
> Neil Armstrong <narmstrong@baylibre.com> writes:
>
>> The G12A & G12B SoCs has kernel controllable CPU clocks and PWMs for
>> voltage regulators.
>>
>> This patchsets moves the meson-g12a.dtsi to meson-g12-common.dtsi to simplify
>> handling the G12A & G12B differences in the meson-g12a.dtsi & meson-g12b.dtsi
>> files, like the OPPs and CPU nodes.
>>
>> Then G12A & G12B OPP tables are added, followed by the CPU voltages regulators
>> in each boards DT.
>>
>> It was voluntary chosen to enabled DVFS (CPU regulator and CPU clocks) only
>> in boards, to make sure only tested boards has DVFS enabled.
>>
>> This patchset :
>> - moves the G12A DT to a common g12a-common dtsi
>> - adds the G12A and G12B OPPs
>> - enables DVFS on all supported boards
>>
>> Dependencies:
>> - None
>
> Not quite. The last patch to enable DVFS on odroid-n2 has a build-time
> dependency on the clock series that adds the CPUB clock.
>
> I'll apply the rest of the series to v5.4/dt64 until there's a stable
> clock tag I can use for the clocks.
In order to test this, I noticed another dependency needed for the PWM
regulators to work:
https://lore.kernel.org/linux-amlogic/20190729125838.6498-1-narmstrong@baylibre.com/
With that and the clock deps, it's working well on my odroid-n2.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Thanks,
Kevin
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 0/6] arm64: g12a: add support for DVFS
2019-08-08 23:56 ` Kevin Hilman
@ 2019-08-09 18:21 ` Kevin Hilman
2019-08-12 20:54 ` Kevin Hilman
1 sibling, 0 replies; 11+ messages in thread
From: Kevin Hilman @ 2019-08-09 18:21 UTC (permalink / raw)
To: Neil Armstrong
Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
Kevin Hilman <khilman@baylibre.com> writes:
> Kevin Hilman <khilman@baylibre.com> writes:
>
>> Neil Armstrong <narmstrong@baylibre.com> writes:
>>
>>> The G12A & G12B SoCs has kernel controllable CPU clocks and PWMs for
>>> voltage regulators.
>>>
>>> This patchsets moves the meson-g12a.dtsi to meson-g12-common.dtsi to simplify
>>> handling the G12A & G12B differences in the meson-g12a.dtsi & meson-g12b.dtsi
>>> files, like the OPPs and CPU nodes.
>>>
>>> Then G12A & G12B OPP tables are added, followed by the CPU voltages regulators
>>> in each boards DT.
>>>
>>> It was voluntary chosen to enabled DVFS (CPU regulator and CPU clocks) only
>>> in boards, to make sure only tested boards has DVFS enabled.
>>>
>>> This patchset :
>>> - moves the G12A DT to a common g12a-common dtsi
>>> - adds the G12A and G12B OPPs
>>> - enables DVFS on all supported boards
>>>
>>> Dependencies:
>>> - None
>>
>> Not quite. The last patch to enable DVFS on odroid-n2 has a build-time
>> dependency on the clock series that adds the CPUB clock.
>>
>> I'll apply the rest of the series to v5.4/dt64 until there's a stable
>> clock tag I can use for the clocks.
>
> In order to test this, I noticed another dependency needed for the PWM
> regulators to work:
>
> https://lore.kernel.org/linux-amlogic/20190729125838.6498-1-narmstrong@baylibre.com/
>
> With that and the clock deps, it's working well on my odroid-n2.
>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
Also now tested on g12a: u200, x96-max and sei510 boards.
Kevin
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH 0/6] arm64: g12a: add support for DVFS
2019-08-08 23:56 ` Kevin Hilman
2019-08-09 18:21 ` Kevin Hilman
@ 2019-08-12 20:54 ` Kevin Hilman
1 sibling, 0 replies; 11+ messages in thread
From: Kevin Hilman @ 2019-08-12 20:54 UTC (permalink / raw)
To: Neil Armstrong
Cc: linux-amlogic, linux-kernel, linux-arm-kernel, Neil Armstrong
Kevin Hilman <khilman@baylibre.com> writes:
> Kevin Hilman <khilman@baylibre.com> writes:
>
>> Neil Armstrong <narmstrong@baylibre.com> writes:
>>
>>> The G12A & G12B SoCs has kernel controllable CPU clocks and PWMs for
>>> voltage regulators.
>>>
>>> This patchsets moves the meson-g12a.dtsi to meson-g12-common.dtsi to simplify
>>> handling the G12A & G12B differences in the meson-g12a.dtsi & meson-g12b.dtsi
>>> files, like the OPPs and CPU nodes.
>>>
>>> Then G12A & G12B OPP tables are added, followed by the CPU voltages regulators
>>> in each boards DT.
>>>
>>> It was voluntary chosen to enabled DVFS (CPU regulator and CPU clocks) only
>>> in boards, to make sure only tested boards has DVFS enabled.
>>>
>>> This patchset :
>>> - moves the G12A DT to a common g12a-common dtsi
>>> - adds the G12A and G12B OPPs
>>> - enables DVFS on all supported boards
>>>
>>> Dependencies:
>>> - None
>>
>> Not quite. The last patch to enable DVFS on odroid-n2 has a build-time
>> dependency on the clock series that adds the CPUB clock.
>>
>> I'll apply the rest of the series to v5.4/dt64 until there's a stable
>> clock tag I can use for the clocks.
>
> In order to test this, I noticed another dependency needed for the PWM
> regulators to work:
>
> https://lore.kernel.org/linux-amlogic/20190729125838.6498-1-narmstrong@baylibre.com/
>
> With that and the clock deps, it's working well on my odroid-n2.
>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
After merging Jerome's tag for clk DT, I've queued this for v5.4,
Thanks,
Kevin
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2019-08-12 20:55 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-29 13:26 [PATCH 0/6] arm64: g12a: add support for DVFS Neil Armstrong
2019-07-29 13:26 ` [PATCH 1/6] arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi Neil Armstrong
2019-07-29 13:26 ` [PATCH 2/6] arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux Neil Armstrong
2019-07-29 13:26 ` [PATCH 3/6] arm64: dts: meson-g12a: add cpus OPP table Neil Armstrong
2019-07-29 13:26 ` [PATCH 4/6] arm64: dts: meson-g12a: enable DVFS on G12A boards Neil Armstrong
2019-07-29 13:26 ` [PATCH 5/6] arm64: dts: meson-g12b: add cpus OPP tables Neil Armstrong
2019-07-29 13:26 ` [PATCH 6/6] arm64: dts: meson-g12b-odroid-n2: enable DVFS Neil Armstrong
2019-08-05 19:07 ` [PATCH 0/6] arm64: g12a: add support for DVFS Kevin Hilman
2019-08-08 23:56 ` Kevin Hilman
2019-08-09 18:21 ` Kevin Hilman
2019-08-12 20:54 ` Kevin Hilman
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).