From: Andrew Murray <andrew.murray@arm.com>
To: Neil Armstrong <narmstrong@baylibre.com>
Cc: lorenzo.pieralisi@arm.com, khilman@baylibre.com,
linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
kishon@ti.com, repk@triplefau.lt, maz@kernel.org,
bhelgaas@google.com, linux-amlogic@lists.infradead.org,
yue.wang@Amlogic.com, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 6/6] arm64: dts: khadas-vim3: add commented support for PCIe
Date: Wed, 11 Sep 2019 14:11:11 +0100 [thread overview]
Message-ID: <20190911131111.GX9720@e119886-lin.cambridge.arm.com> (raw)
In-Reply-To: <bf7b735d-e682-52db-ea8c-4ccd786f0ed9@baylibre.com>
On Wed, Sep 11, 2019 at 02:58:18PM +0200, Neil Armstrong wrote:
> On 11/09/2019 14:50, Andrew Murray wrote:
> > On Sun, Sep 08, 2019 at 01:42:58PM +0000, Neil Armstrong wrote:
> >> The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
> >> lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
> >> an USB3.0 Type A connector and a M.2 Key M slot.
> >> The PHY driving these differential lines is shared between
> >> the USB3.0 controller and the PCIe Controller, thus only
> >> a single controller can use it.
> >>
> >> The needed DT configuration when the MCU is configured to mux
> >> the PCIe/USB3.0 differential lines to the M.2 Key M slot is
> >> added commented and may uncommented to disable USB3.0 from the
> >
> > *and may be*
> >
> >> USB Complex and enable the PCIe controller.
> >>
> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> >> ---
> >> .../amlogic/meson-g12b-a311d-khadas-vim3.dts | 22 +++++++++++++++++++
> >> .../amlogic/meson-g12b-s922x-khadas-vim3.dts | 22 +++++++++++++++++++
> >> .../boot/dts/amlogic/meson-khadas-vim3.dtsi | 4 ++++
> >> .../dts/amlogic/meson-sm1-khadas-vim3l.dts | 22 +++++++++++++++++++
> >> 4 files changed, 70 insertions(+)
> >>
> >> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
> >> index 3a6a1e0c1e32..0577b1435cbb 100644
> >> --- a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
> >> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
> >> @@ -14,3 +14,25 @@
> >> / {
> >> compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b";
> >> };
> >> +
> >> +/*
> >> + * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
> >> + * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
> >> + * an USB3.0 Type A connector and a M.2 Key M slot.
> >> + * The PHY driving these differential lines is shared between
> >> + * the USB3.0 controller and the PCIe Controller, thus only
> >> + * a single controller can use it.
> >> + * If the MCU is configured to mux the PCIe/USB3.0 differential lines
> >> + * to the M.2 Key M slot, uncomment the following block to disable
> >> + * USB3.0 from the USB Complex and enable the PCIe controller.
> >> + */
> >> +/*
> >> +&pcie {
> >> + status = "okay";
> >> +};
> >> +
> >> +&usb {
> >> + phys = <&usb2_phy0>, <&usb2_phy1>;
> >> + phy-names = "usb2-phy0", "usb2-phy1";
> >> +};
> >
> > I assume there is no way other way to determine from the hardware which way
> > the mux is set?
>
> No, it would be simpler :-/ The MUX is on-board and the MCU drives the MUX selection.
>
> You can look at the https://dl.khadas.com/Hardware/VIM3/Schematic/VIM3_V11_Sch.pdf
> The PCIE_EN signal is driven by the STM8S MCU.
Ah I see.
>
> >
> > Otherwise phy_g12a_usb3_pcie_xlate could determine the hardware mode, and
> > reject the phy instance with the wrong mode. Thus resulting in either the
> > PCI or USB to fail their probe. And avoiding the need to modify the DT on
> > boot.
>
> Yep, it would have been simpler this way. Maybe a board vendor will set a gpio ?
> who knows, but for actual boards it's static or with 0ohm resistors, and for the
> VIM3 we only know by asking the MCU.
>
> Maybe we could add a fake PHY as a MCU MFD subdevice, wrapping calls to the
> right PHY. But for now the MCU has no upstream driver anyway.
OK
Thanks,
Andrew Murray
>
> Neil
>
> >
> > Thanks,
> >
> > Andrew Murray
> >
> >> + */
> >> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
> >> index b73deb282120..1ef5c2f04f67 100644
> >> --- a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
> >> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
> >> @@ -14,3 +14,25 @@
> >> / {
> >> compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b";
> >> };
> >> +
> >> +/*
> >> + * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
> >> + * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
> >> + * an USB3.0 Type A connector and a M.2 Key M slot.
> >> + * The PHY driving these differential lines is shared between
> >> + * the USB3.0 controller and the PCIe Controller, thus only
> >> + * a single controller can use it.
> >> + * If the MCU is configured to mux the PCIe/USB3.0 differential lines
> >> + * to the M.2 Key M slot, uncomment the following block to disable
> >> + * USB3.0 from the USB Complex and enable the PCIe controller.
> >> + */
> >> +/*
> >> +&pcie {
> >> + status = "okay";
> >> +};
> >> +
> >> +&usb {
> >> + phys = <&usb2_phy0>, <&usb2_phy1>;
> >> + phy-names = "usb2-phy0", "usb2-phy1";
> >> +};
> >> + */
> >> diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
> >> index 8647da7d6609..eac5720dc15f 100644
> >> --- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
> >> +++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
> >> @@ -246,6 +246,10 @@
> >> linux,rc-map-name = "rc-khadas";
> >> };
> >>
> >> +&pcie {
> >> + reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>;
> >> +};
> >> +
> >> &pwm_ef {
> >> status = "okay";
> >> pinctrl-0 = <&pwm_e_pins>;
> >> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
> >> index 5233bd7cacfb..d9c7cbedce53 100644
> >> --- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
> >> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
> >> @@ -68,3 +68,25 @@
> >> clock-names = "clkin1";
> >> status = "okay";
> >> };
> >> +
> >> +/*
> >> + * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
> >> + * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
> >> + * an USB3.0 Type A connector and a M.2 Key M slot.
> >> + * The PHY driving these differential lines is shared between
> >> + * the USB3.0 controller and the PCIe Controller, thus only
> >> + * a single controller can use it.
> >> + * If the MCU is configured to mux the PCIe/USB3.0 differential lines
> >> + * to the M.2 Key M slot, uncomment the following block to disable
> >> + * USB3.0 from the USB Complex and enable the PCIe controller.
> >> + */
> >> +/*
> >> +&pcie {
> >> + status = "okay";
> >> +};
> >> +
> >> +&usb {
> >> + phys = <&usb2_phy0>, <&usb2_phy1>;
> >> + phy-names = "usb2-phy0", "usb2-phy1";
> >> +};
> >> + */
> >> --
> >> 2.17.1
> >>
>
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
prev parent reply other threads:[~2019-09-11 13:11 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-09-08 13:42 [PATCH 0/6] arm64: dts: meson-g12: add support for PCIe Neil Armstrong
2019-09-08 13:42 ` [PATCH 1/6] dt-bindings: pci: amlogic,meson-pcie: Add G12A bindings Neil Armstrong
2019-09-11 12:22 ` Andrew Murray
2019-09-11 12:30 ` Neil Armstrong
2019-09-13 14:36 ` [PATCH 1/6] dt-bindings: pci: amlogic, meson-pcie: " Rob Herring
2019-09-08 13:42 ` [PATCH 2/6] PCI: amlogic: Fix probed clock names Neil Armstrong
2019-09-11 10:59 ` Andrew Murray
2019-09-08 13:42 ` [PATCH 3/6] PCI: amlogic: meson: Add support for G12A Neil Armstrong
2019-09-11 11:36 ` Andrew Murray
2019-09-11 12:39 ` Neil Armstrong
2019-09-11 12:58 ` Andrew Murray
2019-09-08 13:42 ` [PATCH 4/6] phy: meson-g12a-usb3-pcie: Add support for PCIe mode Neil Armstrong
2019-09-11 12:19 ` Andrew Murray
2019-09-11 12:45 ` Neil Armstrong
2019-09-11 12:59 ` Andrew Murray
2019-09-08 13:42 ` [PATCH 5/6] arm64: dts: meson-g12a: Add PCIe node Neil Armstrong
2019-09-08 13:42 ` [PATCH 6/6] arm64: dts: khadas-vim3: add commented support for PCIe Neil Armstrong
2019-09-09 16:37 ` Marc Zyngier
2019-09-09 17:50 ` Neil Armstrong
2019-09-10 9:12 ` Marc Zyngier
2019-09-10 9:14 ` Neil Armstrong
2019-09-11 12:50 ` Andrew Murray
2019-09-11 12:58 ` Neil Armstrong
2019-09-11 13:11 ` Andrew Murray [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190911131111.GX9720@e119886-lin.cambridge.arm.com \
--to=andrew.murray@arm.com \
--cc=bhelgaas@google.com \
--cc=khilman@baylibre.com \
--cc=kishon@ti.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=maz@kernel.org \
--cc=narmstrong@baylibre.com \
--cc=repk@triplefau.lt \
--cc=yue.wang@Amlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).