Linux-Amlogic Archive on lore.kernel.org
 help / color / Atom feed
From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To: narmstrong@baylibre.com, jbrunet@baylibre.com,
	linux-amlogic@lists.infradead.org, khilman@baylibre.com
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
	Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
	linux-kernel@vger.kernel.org, robh+dt@kernel.org,
	linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 2/5] clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller
Date: Sun, 27 Oct 2019 17:23:25 +0100
Message-ID: <20191027162328.1177402-3-martin.blumenstingl@googlemail.com> (raw)
In-Reply-To: <20191027162328.1177402-1-martin.blumenstingl@googlemail.com>

The Meson8/Meson8b/Meson8m2 SoCs embed a DDR clock controller in the
MMCBUS registers. There is no public documentation, but the u-boot GPL
sources from the Amlogic BSP show that the DDR clock controller is
identical on all three SoCs:
  #define CFG_DDR_CLK 792
  #define CFG_PLL_M (((CFG_DDR_CLK/12)*12)/24)
  #define CFG_PLL_N 1
  #define CFG_PLL_OD 1

  // from set_ddr_clock:
  t_ddr_pll_cntl= (CFG_PLL_OD << 16)|(CFG_PLL_N<<9)|(CFG_PLL_M<<0)
  writel(timing_reg->t_ddr_pll_cntl|(1<<29),AM_DDR_PLL_CNTL);
  writel(readl(AM_DDR_PLL_CNTL) & (~(1<<29)),AM_DDR_PLL_CNTL);

  // from hx_ddr_power_down_enter: shut down DDR PLL
  writel(readl(AM_DDR_PLL_CNTL)|(1<<30),AM_DDR_PLL_CNTL);

  do { ... } while((readl(AM_DDR_PLL_CNTL)&(1<<31))==0)

This translates to:
- AM_DDR_PLL_CNTL[29] is the reset bit
- AM_DDR_PLL_CNTL[30] is the enable bit
- AM_DDR_PLL_CNTL[31] is the lock bit
- AM_DDR_PLL_CNTL[8:0] is the m value (assuming the width is 9 bits
  based on the start of the n value)
- AM_DDR_PLL_CNTL[13:9] is the n value (assuming the width is 5 bits
  based on the start of the od)
- AM_DDR_PLL_CNTL[17:16] is the od (assuming the width is 2 bits based
  on other PLLs on this SoC)

Add a driver for this PLL setup because it's used as one of the inputs
of the audio clocks. There may be more clocks inside that clock
controller - those can be added in subsequent patches.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 drivers/clk/meson/Makefile     |   2 +-
 drivers/clk/meson/meson8-ddr.c | 152 +++++++++++++++++++++++++++++++++
 2 files changed, 153 insertions(+), 1 deletion(-)
 create mode 100644 drivers/clk/meson/meson8-ddr.c

diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 3939f218587a..6eca2a406ee3 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -18,4 +18,4 @@ obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
 obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
 obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
 obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
-obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
+obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o meson8-ddr.o
diff --git a/drivers/clk/meson/meson8-ddr.c b/drivers/clk/meson/meson8-ddr.c
new file mode 100644
index 000000000000..4aefcc5bdaae
--- /dev/null
+++ b/drivers/clk/meson/meson8-ddr.c
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Amlogic Meson8 DDR clock controller
+ *
+ * Copyright (C) 2019 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ */
+
+#include <dt-bindings/clock/meson8-ddr-clkc.h>
+
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+
+#include "clk-regmap.h"
+#include "clk-pll.h"
+
+#define AM_DDR_PLL_CNTL			0x00
+#define AM_DDR_PLL_CNTL1		0x04
+#define AM_DDR_PLL_CNTL2		0x08
+#define AM_DDR_PLL_CNTL3		0x0c
+#define AM_DDR_PLL_CNTL4		0x10
+#define AM_DDR_PLL_STS			0x14
+#define DDR_CLK_CNTL			0x18
+#define DDR_CLK_STS			0x1c
+
+static struct clk_regmap meson8_ddr_pll_dco = {
+	.data = &(struct meson_clk_pll_data){
+		.en = {
+			.reg_off = AM_DDR_PLL_CNTL,
+			.shift   = 30,
+			.width   = 1,
+		},
+		.m = {
+			.reg_off = AM_DDR_PLL_CNTL,
+			.shift   = 0,
+			.width   = 9,
+		},
+		.n = {
+			.reg_off = AM_DDR_PLL_CNTL,
+			.shift   = 9,
+			.width   = 5,
+		},
+		.l = {
+			.reg_off = AM_DDR_PLL_CNTL,
+			.shift   = 31,
+			.width   = 1,
+		},
+		.rst = {
+			.reg_off = AM_DDR_PLL_CNTL,
+			.shift   = 29,
+			.width   = 1,
+		},
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "ddr_pll_dco",
+		.ops = &meson_clk_pll_ro_ops,
+		.parent_data = &(const struct clk_parent_data) {
+			.fw_name = "xtal",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap meson8_ddr_pll = {
+	.data = &(struct clk_regmap_div_data){
+		.offset = AM_DDR_PLL_CNTL,
+		.shift = 16,
+		.width = 2,
+		.flags = CLK_DIVIDER_POWER_OF_TWO,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "ddr_pll",
+		.ops = &clk_regmap_divider_ro_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&meson8_ddr_pll_dco.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_hw_onecell_data meson8_ddr_clk_hw_onecell_data = {
+	.hws = {
+		[DDR_CLKID_DDR_PLL_DCO]		= &meson8_ddr_pll_dco.hw,
+		[DDR_CLKID_DDR_PLL]		= &meson8_ddr_pll.hw,
+	},
+	.num = 2,
+};
+
+static struct clk_regmap *const meson8_ddr_clk_regmaps[] = {
+	&meson8_ddr_pll_dco,
+	&meson8_ddr_pll,
+};
+
+static const struct regmap_config meson8_ddr_clkc_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = DDR_CLK_STS,
+};
+
+static int meson8_ddr_clkc_probe(struct platform_device *pdev)
+{
+	struct regmap *regmap;
+	struct resource *res;
+	void __iomem *base;
+	struct clk_hw *hw;
+	int ret, i;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	regmap = devm_regmap_init_mmio(&pdev->dev, base,
+				       &meson8_ddr_clkc_regmap_config);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	/* Populate regmap */
+	for (i = 0; i < ARRAY_SIZE(meson8_ddr_clk_regmaps); i++)
+		meson8_ddr_clk_regmaps[i]->map = regmap;
+
+	/* Register all clks */
+	for (i = 0; i < meson8_ddr_clk_hw_onecell_data.num; i++) {
+		hw = meson8_ddr_clk_hw_onecell_data.hws[i];
+
+		ret = devm_clk_hw_register(&pdev->dev, hw);
+		if (ret) {
+			dev_err(&pdev->dev, "Clock registration failed\n");
+			return ret;
+		}
+	}
+
+	return devm_of_clk_add_hw_provider(&pdev->dev, of_clk_hw_onecell_get,
+					   &meson8_ddr_clk_hw_onecell_data);
+}
+
+static const struct of_device_id meson8_ddr_clkc_match_table[] = {
+	{ .compatible = "amlogic,meson8-ddr-clkc" },
+	{ .compatible = "amlogic,meson8b-ddr-clkc" },
+	{ /* sentinel */ },
+};
+
+static struct platform_driver meson8_ddr_clkc_driver = {
+	.probe		= meson8_ddr_clkc_probe,
+	.driver		= {
+		.name	= "meson8-ddr-clkc",
+		.of_match_table = meson8_ddr_clkc_match_table,
+	},
+};
+
+builtin_platform_driver(meson8_ddr_clkc_driver);
-- 
2.23.0


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

  parent reply index

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-27 16:23 [PATCH v2 0/5] add the DDR clock controller on Meson8 and Meson8b Martin Blumenstingl
2019-10-27 16:23 ` [PATCH v2 1/5] dt-bindings: clock: add the Amlogic Meson8 DDR clock controller binding Martin Blumenstingl
2019-11-08 22:07   ` Stephen Boyd
2019-10-27 16:23 ` Martin Blumenstingl [this message]
2019-11-08 22:16   ` [PATCH v2 2/5] clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller Stephen Boyd
2019-11-12 17:20     ` Jerome Brunet
2019-11-12 20:52       ` Martin Blumenstingl
2019-11-16 16:52         ` Martin Blumenstingl
2019-10-27 16:23 ` [PATCH v2 3/5] clk: meson: meson8b: use of_clk_hw_register to register the clocks Martin Blumenstingl
2019-11-08 22:07   ` Stephen Boyd
2019-10-27 16:23 ` [PATCH v2 4/5] ARM: dts: meson8: add the DDR clock controller Martin Blumenstingl
2019-10-27 16:23 ` [PATCH v2 5/5] ARM: dts: meson8b: " Martin Blumenstingl

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191027162328.1177402-3-martin.blumenstingl@googlemail.com \
    --to=martin.blumenstingl@googlemail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=jbrunet@baylibre.com \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=narmstrong@baylibre.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Amlogic Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-amlogic/0 linux-amlogic/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-amlogic linux-amlogic/ https://lore.kernel.org/linux-amlogic \
		linux-amlogic@lists.infradead.org
	public-inbox-index linux-amlogic

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-amlogic


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git