[PATCH v6 5/7] phy: amlogic: Add Amlogic AXG MIPI/PCIE analog PHY Driver

[Remi Pommarel <repk@triplefau.lt>]

This adds support for the MIPI analog PHY which is also used for PCIE
found in the Amlogic AXG SoC Family.

MIPI or PCIE selection is done by the #phy-cells, making the mode
static and exclusive.

For now only PCIE fonctionality is supported.

This PHY will be used to replace the mipi_enable clock gating logic
which was mistakenly added in the clock subsystem. This also activate
a non documented band gap bit in those registers that allows reliable
PCIE clock signal generation on AXG platforms.

Signed-off-by: Remi Pommarel <repk@triplefau.lt>
---
 drivers/phy/amlogic/Kconfig                   |  11 +
 drivers/phy/amlogic/Makefile                  |  11 +-
 .../amlogic/phy-meson-axg-mipi-pcie-analog.c  | 188 ++++++++++++++++++
 3 files changed, 205 insertions(+), 5 deletions(-)
 create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c

diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
index af774ac2b934..8c9cf2403591 100644
--- a/drivers/phy/amlogic/Kconfig
+++ b/drivers/phy/amlogic/Kconfig
@@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
 	  Enable this to support the Meson USB3 + PCIE Combo PHY found
 	  in Meson G12A SoCs.
 	  If unsure, say N.
+
+config PHY_MESON_AXG_MIPI_PCIE_ANALOG
+	tristate "Meson AXG MIPI + PCIE analog PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Enable this to support the Meson MIPI + PCIE analog PHY
+	  found in Meson AXG SoCs.
+	  If unsure, say N.
diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
index 11d1c42ac2be..0aecf92d796a 100644
--- a/drivers/phy/amlogic/Makefile
+++ b/drivers/phy/amlogic/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
-obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
-obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
-obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
-obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
-obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
+obj-$(CONFIG_PHY_MESON8B_USB2)			+= phy-meson8b-usb2.o
+obj-$(CONFIG_PHY_MESON_GXL_USB2)		+= phy-meson-gxl-usb2.o
+obj-$(CONFIG_PHY_MESON_G12A_USB2)		+= phy-meson-g12a-usb2.o
+obj-$(CONFIG_PHY_MESON_GXL_USB3)		+= phy-meson-gxl-usb3.o
+obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)		+= phy-meson-g12a-usb3-pcie.o
+obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG)	+= phy-meson-axg-mipi-pcie-analog.o
diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
new file mode 100644
index 000000000000..1431cbf885e1
--- /dev/null
+++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Amlogic AXG MIPI + PCIE analog PHY driver
+ *
+ * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
+ */
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/phy/phy.h>
+
+#define HHI_MIPI_CNTL0 0x00
+#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
+#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
+#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
+#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
+#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
+
+#define HHI_MIPI_CNTL1 0x01
+#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
+#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
+#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
+#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
+#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
+#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
+
+#define HHI_MIPI_CNTL2 0x02
+#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
+#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
+#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
+#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
+#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
+#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
+#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
+
+struct phy_axg_mipi_pcie_analog_priv {
+	struct phy *phy;
+	unsigned int mode;
+	struct regmap *regmap;
+};
+
+static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = HHI_MIPI_CNTL2,
+};
+
+static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
+{
+	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
+
+	/* MIPI not supported yet */
+	if (priv->mode != PHY_TYPE_PCIE)
+		return -EINVAL;
+
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
+
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
+	return 0;
+}
+
+static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
+{
+	struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
+
+	/* MIPI not supported yet */
+	if (priv->mode != PHY_TYPE_PCIE)
+		return -EINVAL;
+
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_BANDGAP, 0);
+	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
+			   HHI_MIPI_CNTL0_ENABLE, 0);
+	return 0;
+}
+
+static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
+{
+	return 0;
+}
+
+static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
+{
+	return 0;
+}
+
+static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
+	.init = phy_axg_mipi_pcie_analog_init,
+	.exit = phy_axg_mipi_pcie_analog_exit,
+	.power_on = phy_axg_mipi_pcie_analog_power_on,
+	.power_off = phy_axg_mipi_pcie_analog_power_off,
+	.owner = THIS_MODULE,
+};
+
+static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
+						  struct of_phandle_args *args)
+{
+	struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
+	unsigned int mode;
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of arguments\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	mode = args->args[0];
+
+	/* MIPI mode is not supported yet */
+	if (mode != PHY_TYPE_PCIE) {
+		dev_err(dev, "invalid phy mode select argument\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	priv->mode = mode;
+	return priv->phy;
+}
+
+static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy;
+	struct device *dev = &pdev->dev;
+	struct phy_axg_mipi_pcie_analog_priv *priv;
+	struct device_node *np = dev->of_node;
+	struct regmap *map;
+	struct resource *res;
+	void __iomem *base;
+	int ret;
+
+	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base)) {
+		dev_err(dev, "failed to get regmap base\n");
+		return PTR_ERR(base);
+	}
+
+	map = devm_regmap_init_mmio(dev, base,
+				    &phy_axg_mipi_pcie_analog_regmap_conf);
+	if (IS_ERR(map)) {
+		dev_err(dev, "failed to get HHI regmap\n");
+		return PTR_ERR(map);
+	}
+	priv->regmap = map;
+
+	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
+	if (IS_ERR(priv->phy)) {
+		ret = PTR_ERR(priv->phy);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "failed to create PHY\n");
+		return ret;
+	}
+
+	phy_set_drvdata(priv->phy, priv);
+	dev_set_drvdata(dev, priv);
+
+	phy = devm_of_phy_provider_register(dev,
+					    phy_axg_mipi_pcie_analog_xlate);
+
+	return PTR_ERR_OR_ZERO(phy);
+}
+
+static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
+	{
+		.compatible = "amlogic,axg-mipi-pcie-analog-phy",
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
+
+static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
+	.probe = phy_axg_mipi_pcie_analog_probe,
+	.driver = {
+		.name = "phy-axg-mipi-pcie-analog",
+		.of_match_table = phy_axg_mipi_pcie_analog_of_match,
+	},
+};
+module_platform_driver(phy_axg_mipi_pcie_analog_driver);
+
+MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
+MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
2.24.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic