[PATCH v3 0/5] arm64: dts: meson: add W400 dtsi and GT-King/Pro devices

[PATCH v3 0/5] arm64: dts: meson: add W400 dtsi and GT-King/Pro devices

[Christian Hewitt]

This series combines patch 2 from [1] which converts the existing Ugoos
AM6 device-tree to a common W400 dtsi and dts, and then reworks the
Beelink GT-King/GT-King Pro serries from [2] to use the dtsi, but this
time without the offending common audio dtsi approach. I've carried
forwards acks on bindings from Rob as these did not change.

v3 - amend author full-name on bindings patch

[1] https://patchwork.kernel.org/patch/11497105/
[2] https://patchwork.kernel.org/project/linux-amlogic/list/?series=273483

Christian Hewitt (5):
  arm64: dts: meson: convert ugoos-am6 to common w400 dtsi
  dt-bindings: arm: amlogic: add support for the Beelink GT-King
  arm64: dts: meson-g12b-gtking: add initial device-tree
  dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro
  arm64: dts: meson-g12b-gtking-pro: add initial device-tree

 .../devicetree/bindings/arm/amlogic.yaml      |   2 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../dts/amlogic/meson-g12b-gtking-pro.dts     | 125 ++++++
 .../boot/dts/amlogic/meson-g12b-gtking.dts    | 145 ++++++
 .../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 410 +----------------
 .../boot/dts/amlogic/meson-g12b-w400.dtsi     | 423 ++++++++++++++++++
 6 files changed, 698 insertions(+), 409 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi

-- 
2.17.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH v3 1/5] arm64: dts: meson: convert ugoos-am6 to common w400 dtsi

[Christian Hewitt]

Convert the Ugoos AM6 dts into meson-g12b-w400.dtsi, and then create
a new AM6 dts that references it. This is in preparation for several
new G12B devices that will share the common w400 dtsi.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 .../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 410 +----------------
 .../boot/dts/amlogic/meson-g12b-w400.dtsi     | 423 ++++++++++++++++++
 2 files changed, 424 insertions(+), 409 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts
index fdaacfd96b97..73637de80c21 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts
@@ -7,42 +7,13 @@
 
 /dts-v1/;
 
-#include "meson-g12b.dtsi"
-#include "meson-g12b-s922x.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include "meson-g12b-w400.dtsi"
 #include <dt-bindings/sound/meson-g12a-tohdmitx.h>
 
 / {
 	compatible = "ugoos,am6", "amlogic,s922x", "amlogic,g12b";
 	model = "Ugoos AM6";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
-	sdio_pwrseq: sdio-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
-		clocks = <&wifi32k>;
-		clock-names = "ext_clock";
-	};
-
 	spdif_dit: audio-codec-1 {
 		#sound-dai-cells = <0>;
 		compatible = "linux,spdif-dit";
@@ -50,154 +21,6 @@
 		sound-name-prefix = "DIT";
 	};
 
-	flash_1v8: regulator-flash_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "FLASH_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	main_12v: regulator-main_12v {
-		compatible = "regulator-fixed";
-		regulator-name = "12V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-always-on;
-	};
-
-	vcc_5v: regulator-vcc_5v {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&main_12v>;
-
-		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-	};
-
-	vcc_1v8: regulator-vcc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	vcc_3v3: regulator-vcc_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-		/* FIXME: actually controlled by VDDCPU_B_EN */
-	};
-
-	vddcpu_a: regulator-vddcpu-a {
-		/*
-		 * MP1653 Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_A";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		vin-supply = <&main_12v>;
-
-		pwms = <&pwm_ab 0 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vddcpu_b: regulator-vddcpu-b {
-		/*
-		 * MP1652 Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU_B";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		vin-supply = <&main_12v>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	usb1_pow: regulator-usb1-pow {
-		compatible = "regulator-fixed";
-		regulator-name = "USB1_POW";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		/* connected to SY6280A Power Switch */
-		gpio = <&gpio GPIOA_8 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	usb_pwr_en: regulator-usb-pwr-en {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		/* Connected to USB3 Type-A Port power enable */
-		gpio = <&gpio GPIOAO_7 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vddao_1v8: regulator-vddao-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&main_12v>;
-		regulator-always-on;
-	};
-
-	cvbs-connector {
-		compatible = "composite-video-connector";
-
-		port {
-			cvbs_connector_in: endpoint {
-				remote-endpoint = <&cvbs_vdac_out>;
-			};
-		};
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "G12B-UGOOS-AM6";
@@ -277,110 +100,16 @@
 			};
 		};
 	};
-
-	wifi32k: wifi32k {
-		compatible = "pwm-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
-	};
 };
 
 &arb {
 	status = "okay";
 };
 
-&cec_AO {
-	pinctrl-0 = <&cec_ao_a_h_pins>;
-	pinctrl-names = "default";
-	status = "disabled";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
-&cecb_AO {
-	pinctrl-0 = <&cec_ao_b_h_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	hdmi-phandle = <&hdmi_tx>;
-};
-
 &clkc_audio {
 	status = "okay";
 };
 
-&cpu0 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu_b>;
-	operating-points-v2 = <&cpu_opp_table_0>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu100 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu101 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu102 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu103 {
-	cpu-supply = <&vddcpu_a>;
-	operating-points-v2 = <&cpub_opp_table_1>;
-	clocks = <&clkc CLKID_CPUB_CLK>;
-	clock-latency = <50000>;
-};
-
-&cvbs_vdac_port {
-	cvbs_vdac_out: endpoint {
-		remote-endpoint = <&cvbs_connector_in>;
-	};
-};
-
-&ext_mdio {
-	external_phy: ethernet-phy@0 {
-		/* Realtek RTL8211F (0x001cc916) */
-		reg = <0>;
-		max-speed = <1000>;
-
-		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
-		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
-
-		interrupt-parent = <&gpio_intc>;
-		/* MAC_INTR on GPIOZ_14 */
-		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii";
-	phy-handle = <&external_phy>;
-	amlogic,tx-delay-ns = <2>;
-};
-
 &frddr_a {
 	status = "okay";
 };
@@ -393,112 +122,10 @@
 	status = "okay";
 };
 
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&vcc_5v>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
 &ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
 	linux,rc-map-name = "rc-khadas";
 };
 
-&pwm_ab {
-	pinctrl-0 = <&pwm_a_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin0";
-	status = "okay";
-};
-
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&pwm_ef {
-	pinctrl-0 = <&pwm_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin0";
-	status = "okay";
-};
-
-/* SDIO */
-&sd_emmc_a {
-	status = "okay";
-	pinctrl-0 = <&sdio_pins>;
-	pinctrl-1 = <&sdio_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	sd-uhs-sdr50;
-	max-frequency = <100000000>;
-
-	non-removable;
-	disable-wp;
-
-	mmc-pwrseq = <&sdio_pwrseq>;
-
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&vddao_1v8>;
-
-	brcmf: wifi@1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-	};
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
-	disable-wp;
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&vddao_3v3>;
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	max-frequency = <100000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&flash_1v8>;
-};
-
 &spdifout {
 	pinctrl-0 = <&spdif_out_h_pins>;
 	pinctrl-names = "default";
@@ -520,38 +147,3 @@
 &tohdmitx {
 	status = "okay";
 };
-
-&uart_A {
-	status = "okay";
-	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
-	pinctrl-names = "default";
-	uart-has-rtscts;
-
-	bluetooth {
-		compatible = "brcm,bcm43438-bt";
-		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
-		max-speed = <2000000>;
-		clocks = <&wifi32k>;
-	clock-names = "lpo";
-	};
-};
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-	dr_mode = "host";
-	vbus-supply = <&usb_pwr_en>;
-};
-
-&usb2_phy0 {
-	phy-supply = <&usb1_pow>;
-};
-
-&usb2_phy1 {
-	phy-supply = <&usb1_pow>;
-};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
new file mode 100644
index 000000000000..98b70d216a6f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
@@ -0,0 +1,423 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include "meson-g12b-s922x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v>;
+
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	vddcpu_a: regulator-vddcpu-a {
+		/*
+		 * MP1653 Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU_A";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		vin-supply = <&main_12v>;
+
+		pwms = <&pwm_ab 0 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddcpu_b: regulator-vddcpu-b {
+		/*
+		 * MP1652 Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU_B";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		vin-supply = <&main_12v>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	usb1_pow: regulator-usb1-pow {
+		compatible = "regulator-fixed";
+		regulator-name = "USB1_POW";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* connected to SY6280A Power Switch */
+		gpio = <&gpio GPIOA_8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usb_pwr_en: regulator-usb-pwr-en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to USB3 Type-A Port power enable */
+		gpio = <&gpio GPIOAO_7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddao_1v8: regulator-vddao-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu_b>;
+	operating-points-v2 = <&cpu_opp_table_0>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu_b>;
+	operating-points-v2 = <&cpu_opp_table_0>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu100 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu101 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu102 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu103 {
+	cpu-supply = <&vddcpu_a>;
+	operating-points-v2 = <&cpub_opp_table_1>;
+	clocks = <&clkc CLKID_CPUB_CLK>;
+	clock-latency = <50000>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		reset-assert-us = <10000>;
+		reset-deassert-us = <30000>;
+		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	pinctrl-0 = <&pwm_a_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+	status = "okay";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&pwm_ef {
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+	status = "okay";
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_1v8>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+	clock-names = "lpo";
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+	vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+	phy-supply = <&usb1_pow>;
+};
+
+&usb2_phy1 {
+	phy-supply = <&usb1_pow>;
+};
-- 
2.17.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH v3 2/5] dt-bindings: arm: amlogic: add support for the Beelink GT-King

[Christian Hewitt]

The Shenzen AZW (Beelink) GT-King is based on the Amlogic W400 reference
board with an S922X chip.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 5180a548bd94..25e118b8a97b 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -151,6 +151,7 @@ properties:
       - description: Boards with the Amlogic Meson G12B S922X SoC
         items:
           - enum:
+              - azw,gtking
               - hardkernel,odroid-n2
               - khadas,vim3
               - ugoos,am6
-- 
2.17.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH v3 3/5] arm64: dts: meson-g12b-gtking: add initial device-tree

[Christian Hewitt]

The Shenzen AZW (Beelink) GT-King is based on the Amlogic W400 reference
board with an S922X chip.

- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- S/PDIF optical output
- Analogue audio output
- 1x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../boot/dts/amlogic/meson-g12b-gtking.dts    | 145 ++++++++++++++++++
 2 files changed, 146 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 01e32415e252..66691090b30c 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-tanix-tx5max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
new file mode 100644
index 000000000000..eeb7bc5539ef
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-w400.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "azw,gtking", "amlogic,g12b";
+	model = "Beelink GT-King";
+
+	spdif_dit: audio-codec-1 {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+		status = "okay";
+		sound-name-prefix = "DIT";
+	};
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "G12B-GTKING";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT",
+				"SPDIFOUT IN 0", "FRDDR_A OUT 3",
+				"SPDIFOUT IN 1", "FRDDR_B OUT 3",
+				"SPDIFOUT IN 2", "FRDDR_C OUT 3";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* spdif hdmi or toslink interface */
+		dai-link-4 {
+			sound-dai = <&spdifout>;
+
+			codec-0 {
+				sound-dai = <&spdif_dit>;
+			};
+
+			codec-1 {
+				sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_A>;
+			};
+		};
+
+		/* spdif hdmi interface */
+		dai-link-5 {
+			sound-dai = <&spdifout_b>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_SPDIF_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-6 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&spdifout {
+	pinctrl-0 = <&spdif_out_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&spdifout_b {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
-- 
2.17.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH v3 4/5] dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro

[Christian Hewitt]

The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400 reference
board with an S922X chip.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 25e118b8a97b..46cb6359f530 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -152,6 +152,7 @@ properties:
         items:
           - enum:
               - azw,gtking
+              - azw,gtking-pro
               - hardkernel,odroid-n2
               - khadas,vim3
               - ugoos,am6
-- 
2.17.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH v3 5/5] arm64: dts: meson-g12b-gtking-pro: add initial device-tree

[Christian Hewitt]

The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400
reference board with an S922X chip.

- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- Analogue audio output
- 1x RS232 port
- 2x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot
- 1x Power on/off button

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../dts/amlogic/meson-g12b-gtking-pro.dts     | 125 ++++++++++++++++++
 2 files changed, 126 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 66691090b30c..38bb1f6e6ef6 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12a-tanix-tx5max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
new file mode 100644
index 000000000000..f0c56a16af3d
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-w400.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "azw,gtking", "amlogic,g12b";
+	model = "Beelink GT-King Pro";
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <100>;
+
+		power-button {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		white {
+			label = "power:white";
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "G12B-GTKING-PRO";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
-- 
2.17.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH v3 0/5] arm64: dts: meson: add W400 dtsi and GT-King/Pro devices

[Kevin Hilman]

Hi Christian,

Christian Hewitt <christianshewitt@gmail.com> writes:

> This series combines patch 2 from [1] which converts the existing Ugoos
> AM6 device-tree to a common W400 dtsi and dts, and then reworks the
> Beelink GT-King/GT-King Pro serries from [2] to use the dtsi, but this
> time without the offending common audio dtsi approach. I've carried
> forwards acks on bindings from Rob as these did not change.

This looks good to me, thank you very much for reworking into a
w400-based include.

Unfortunately, it no longer applies on top of all the other stuff I have
queued for v5.8.

Could you please do a rebase on top of my v5.8/dt64 branch[1], and I'll
queue for v5.8.

Thanks,

Kevin

> v3 - amend author full-name on bindings patch
>
> [1] https://patchwork.kernel.org/patch/11497105/
> [2] https://patchwork.kernel.org/project/linux-amlogic/list/?series=273483
>
> Christian Hewitt (5):
>   arm64: dts: meson: convert ugoos-am6 to common w400 dtsi
>   dt-bindings: arm: amlogic: add support for the Beelink GT-King
>   arm64: dts: meson-g12b-gtking: add initial device-tree
>   dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro
>   arm64: dts: meson-g12b-gtking-pro: add initial device-tree
>
>  .../devicetree/bindings/arm/amlogic.yaml      |   2 +
>  arch/arm64/boot/dts/amlogic/Makefile          |   2 +
>  .../dts/amlogic/meson-g12b-gtking-pro.dts     | 125 ++++++
>  .../boot/dts/amlogic/meson-g12b-gtking.dts    | 145 ++++++
>  .../boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 410 +----------------
>  .../boot/dts/amlogic/meson-g12b-w400.dtsi     | 423 ++++++++++++++++++
>  6 files changed, 698 insertions(+), 409 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
>
> -- 
> 2.17.1

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic