Linux-Amlogic Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 0/3] ARM: dts: use the SDHC MMC controller for eMMC
@ 2020-06-20 16:36 Martin Blumenstingl
  2020-06-20 16:36 ` [PATCH 1/3] ARM: dts: meson: add the SDHC MMC controller Martin Blumenstingl
                   ` (2 more replies)
  0 siblings, 3 replies; 4+ messages in thread
From: Martin Blumenstingl @ 2020-06-20 16:36 UTC (permalink / raw)
  To: linux-amlogic, khilman
  Cc: Martin Blumenstingl, linux-kernel, linux-arm-kernel

Amlogic Meson6/8/8b/8m2 SoCs have two built-in MMC controllers:
- SDIO (which is supported on mainline for a long time now but is
  limited to ~40MHz bus frequency)
- SDHC (which supports up to HS-200 modes at ~100MHz bus frequency but
  for which we didn't have a driver)

Boards with NAND flash will now be able to use the SDIO controller for
SDIO based wifi cards and the SDHC controller for the SD card slot.
Boards with eMMC, SD card and SDIO wifi can only use two out of three
MMC based devices for now until the MMC core and Meson SDIO driver gain
support for multiple "mmc-slots" per controller.

Now that we have a driver for it, add the SDHC controller to meson.dtsi
and wire up the eMMC connection on the Endless Mini EC-100 and the
Odroid-C1.


Martin Blumenstingl (3):
  ARM: dts: meson: add the SDHC MMC controller
  ARM: dts: meson8b: ec100: enable the SDHC controller
  ARM: dts: meson8b: odroidc1: enable the SDHC controller

 arch/arm/boot/dts/meson.dtsi           |  7 +++++++
 arch/arm/boot/dts/meson8.dtsi          | 19 +++++++++++++++++++
 arch/arm/boot/dts/meson8b-ec100.dts    | 25 +++++++++++++++++++++++++
 arch/arm/boot/dts/meson8b-odroidc1.dts | 26 ++++++++++++++++++++++++++
 arch/arm/boot/dts/meson8b.dtsi         | 20 ++++++++++++++++++++
 arch/arm/boot/dts/meson8m2.dtsi        |  4 ++++
 6 files changed, 101 insertions(+)

-- 
2.27.0


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply	[flat|nested] 4+ messages in thread

* [PATCH 1/3] ARM: dts: meson: add the SDHC MMC controller
  2020-06-20 16:36 [PATCH 0/3] ARM: dts: use the SDHC MMC controller for eMMC Martin Blumenstingl
@ 2020-06-20 16:36 ` Martin Blumenstingl
  2020-06-20 16:36 ` [PATCH 2/3] ARM: dts: meson8b: ec100: enable the SDHC controller Martin Blumenstingl
  2020-06-20 16:36 ` [PATCH 3/3] ARM: dts: meson8b: odroidc1: " Martin Blumenstingl
  2 siblings, 0 replies; 4+ messages in thread
From: Martin Blumenstingl @ 2020-06-20 16:36 UTC (permalink / raw)
  To: linux-amlogic, khilman
  Cc: Martin Blumenstingl, linux-kernel, linux-arm-kernel

Meson6, Meson8, Meson8b and Meson8m2 are using a similar SDHC controller
IP which typically connects to an eMMC chip (because unlike the SDIO
controller the SDHC controller has an 8-bit bus interface).

On Meson8, Meson8b and Meson8m2 the clock inputs are all the same.
However, Meson8m2 seems to have an improved version of the SHDC
controller IP which doesn't require the driver to wait manually for a
flush of a DMA transfer. Thus every SoC has it's own compatible string
so if more difference are discovered they can be implemented.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 arch/arm/boot/dts/meson.dtsi    |  7 +++++++
 arch/arm/boot/dts/meson8.dtsi   | 19 +++++++++++++++++++
 arch/arm/boot/dts/meson8b.dtsi  | 20 ++++++++++++++++++++
 arch/arm/boot/dts/meson8m2.dtsi |  4 ++++
 4 files changed, 50 insertions(+)

diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi
index ae89deaa8c9c..464057989572 100644
--- a/arch/arm/boot/dts/meson.dtsi
+++ b/arch/arm/boot/dts/meson.dtsi
@@ -140,6 +140,13 @@ spifc: spi@8c80 {
 				status = "disabled";
 			};
 
+			sdhc: mmc@8e00 {
+				compatible = "amlogic,meson-mx-sdhc";
+				reg = <0x8e00 0x42>;
+				interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+			};
+
 			gpio_intc: interrupt-controller@9880 {
 				compatible = "amlogic,meson-gpio-intc";
 				reg = <0x9880 0x10>;
diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index 3d0ab2ac5332..04688e8abce2 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -384,6 +384,15 @@ mux {
 			};
 		};
 
+		sdxc_b_pins: sdxc-b {
+			mux {
+				groups = "sdxc_d0_b", "sdxc_d13_b",
+					 "sdxc_clk_b", "sdxc_cmd_b";
+				function = "sdxc_b";
+				bias-pull-up;
+			};
+		};
+
 		spi_nor_pins: nor {
 			mux {
 				groups = "nor_d", "nor_q", "nor_c", "nor_cs";
@@ -558,6 +567,16 @@ &saradc {
 	nvmem-cell-names = "temperature_calib";
 };
 
+&sdhc {
+	compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc";
+	clocks = <&xtal>,
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>,
+		 <&clkc CLKID_FCLK_DIV5>,
+		 <&clkc CLKID_SDHC>;
+	clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk";
+};
+
 &sdio {
 	compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio";
 	clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>;
diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
index 2069c57343e5..2401cdf5f751 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -363,6 +363,16 @@ mux {
 			};
 		};
 
+		sdxc_c_pins: sdxc-c {
+			mux {
+				groups = "sdxc_d0_c", "sdxc_d13_c",
+					 "sdxc_d47_c", "sdxc_clk_c",
+					 "sdxc_cmd_c";
+				function = "sdxc_c";
+				bias-pull-up;
+			};
+		};
+
 		pwm_c1_pins: pwm-c1 {
 			mux {
 				groups = "pwm_c1";
@@ -554,6 +564,16 @@ &saradc {
 	nvmem-cell-names = "temperature_calib";
 };
 
+&sdhc {
+	compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc";
+	clocks = <&xtal>,
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>,
+		 <&clkc CLKID_FCLK_DIV5>,
+		 <&clkc CLKID_SDHC>;
+	clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk";
+};
+
 &sdio {
 	compatible = "amlogic,meson8b-sdio", "amlogic,meson-mx-sdio";
 	clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>;
diff --git a/arch/arm/boot/dts/meson8m2.dtsi b/arch/arm/boot/dts/meson8m2.dtsi
index c7ddbb210366..6725dd9fd825 100644
--- a/arch/arm/boot/dts/meson8m2.dtsi
+++ b/arch/arm/boot/dts/meson8m2.dtsi
@@ -84,6 +84,10 @@ &saradc {
 	compatible = "amlogic,meson8m2-saradc", "amlogic,meson-saradc";
 };
 
+&sdhc {
+	compatible = "amlogic,meson8m2-sdhc", "amlogic,meson-mx-sdhc";
+};
+
 &usb0_phy {
 	compatible = "amlogic,meson8m2-usb2-phy", "amlogic,meson-mx-usb2-phy";
 };
-- 
2.27.0


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply	[flat|nested] 4+ messages in thread

* [PATCH 2/3] ARM: dts: meson8b: ec100: enable the SDHC controller
  2020-06-20 16:36 [PATCH 0/3] ARM: dts: use the SDHC MMC controller for eMMC Martin Blumenstingl
  2020-06-20 16:36 ` [PATCH 1/3] ARM: dts: meson: add the SDHC MMC controller Martin Blumenstingl
@ 2020-06-20 16:36 ` Martin Blumenstingl
  2020-06-20 16:36 ` [PATCH 3/3] ARM: dts: meson8b: odroidc1: " Martin Blumenstingl
  2 siblings, 0 replies; 4+ messages in thread
From: Martin Blumenstingl @ 2020-06-20 16:36 UTC (permalink / raw)
  To: linux-amlogic, khilman
  Cc: Martin Blumenstingl, linux-kernel, linux-arm-kernel

EC-100 has built-in eMMC flash which is hard-wired to 3.3V VCC (which
means it's limited to high-speed MMC modes). Enable the SDHC controller
to access the contents of the eMMC flash.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 arch/arm/boot/dts/meson8b-ec100.dts | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/meson8b-ec100.dts
index 163a200d5a7b..ed06102a4014 100644
--- a/arch/arm/boot/dts/meson8b-ec100.dts
+++ b/arch/arm/boot/dts/meson8b-ec100.dts
@@ -27,6 +27,11 @@ memory {
 		reg = <0x40000000 0x40000000>;
 	};
 
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys-polled";
 		#address-cells = <1>;
@@ -299,6 +304,26 @@ &saradc {
 	vref-supply = <&vcc_1v8>;
 };
 
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_c_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	max-frequency = <50000000>;
+
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	no-sdio;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
 &sdio {
 	status = "okay";
 
-- 
2.27.0


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply	[flat|nested] 4+ messages in thread

* [PATCH 3/3] ARM: dts: meson8b: odroidc1: enable the SDHC controller
  2020-06-20 16:36 [PATCH 0/3] ARM: dts: use the SDHC MMC controller for eMMC Martin Blumenstingl
  2020-06-20 16:36 ` [PATCH 1/3] ARM: dts: meson: add the SDHC MMC controller Martin Blumenstingl
  2020-06-20 16:36 ` [PATCH 2/3] ARM: dts: meson8b: ec100: enable the SDHC controller Martin Blumenstingl
@ 2020-06-20 16:36 ` Martin Blumenstingl
  2 siblings, 0 replies; 4+ messages in thread
From: Martin Blumenstingl @ 2020-06-20 16:36 UTC (permalink / raw)
  To: linux-amlogic, khilman
  Cc: Martin Blumenstingl, linux-kernel, linux-arm-kernel

Odroid-C1 has an eMMC connector where users can optionally install an
eMMC module. The eMMC modules run off a 1.8V VQMMC supply which means
that HS-200 mode can be used (this is the highest mode that the SDHC
controller supports). Enable the SDHC controller so eMMC modules can be
accessed.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 arch/arm/boot/dts/meson8b-odroidc1.dts | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index cb21ac9f517c..0c26467de4d0 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -15,6 +15,7 @@ / {
 	aliases {
 		serial0 = &uart_AO;
 		mmc0 = &sd_card_slot;
+		mmc1 = &sdhc;
 	};
 
 	chosen {
@@ -26,6 +27,11 @@ memory {
 		reg = <0x40000000 0x40000000>;
 	};
 
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		blue {
@@ -310,6 +316,26 @@ &saradc {
 	vref-supply = <&vcc_1v8>;
 };
 
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_c_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <8>;
+	max-frequency = <100000000>;
+
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	no-sdio;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+};
+
 &sdio {
 	status = "okay";
 
-- 
2.27.0


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, back to index

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-20 16:36 [PATCH 0/3] ARM: dts: use the SDHC MMC controller for eMMC Martin Blumenstingl
2020-06-20 16:36 ` [PATCH 1/3] ARM: dts: meson: add the SDHC MMC controller Martin Blumenstingl
2020-06-20 16:36 ` [PATCH 2/3] ARM: dts: meson8b: ec100: enable the SDHC controller Martin Blumenstingl
2020-06-20 16:36 ` [PATCH 3/3] ARM: dts: meson8b: odroidc1: " Martin Blumenstingl

Linux-Amlogic Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-amlogic/0 linux-amlogic/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-amlogic linux-amlogic/ https://lore.kernel.org/linux-amlogic \
		linux-amlogic@lists.infradead.org
	public-inbox-index linux-amlogic

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-amlogic


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git