Linux-Amlogic Archive on lore.kernel.org
 help / color / Atom feed
From: guillaume La Roque <glaroque@baylibre.com>
To: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
	khilman@baylibre.com, linus.walleij@linaro.org,
	linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
	robh+dt@kernel.org, linux-amlogic@lists.infradead.org
Subject: Re: [PATCH v3 5/6] pinctrl: meson: add support of drive-strength-microamp
Date: Thu, 9 May 2019 13:23:34 +0200
Message-ID: <4e44984f-eb76-87d1-e458-506bcccf1500@baylibre.com> (raw)
In-Reply-To: <CAFBinCC-wYD1ZJ8Dd6mwd=qAqi8YX0=VacjbEc-bxKrQnZvwDA@mail.gmail.com>

hi martin,


thanks for review, i will do a new series to remove err log on get_drive_strength

and integrate your comment


On 5/7/19 8:18 PM, Martin Blumenstingl wrote:
> On Tue, May 7, 2019 at 1:57 PM Guillaume La Roque <glaroque@baylibre.com> wrote:
>> drive-strength-microamp is a new feature needed for G12A SoC.
>> the default DS setting after boot is usually 500uA and it is not enough for
>> many functions. We need to be able to set the drive strength to reliably
>> enable things like MMC, I2C, etc ...
>>
>> Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
> with the comments below addressed:
> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>
>> ---
>>  drivers/pinctrl/meson/pinctrl-meson.c | 102 ++++++++++++++++++++++++++
>>  drivers/pinctrl/meson/pinctrl-meson.h |  18 ++++-
>>  2 files changed, 119 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/pinctrl/meson/pinctrl-meson.c b/drivers/pinctrl/meson/pinctrl-meson.c
>> index a216a7537564..3da867c13f47 100644
>> --- a/drivers/pinctrl/meson/pinctrl-meson.c
>> +++ b/drivers/pinctrl/meson/pinctrl-meson.c
>> @@ -219,12 +219,56 @@ static int meson_pinconf_enable_bias(struct meson_pinctrl *pc, unsigned int pin,
>>         return 0;
>>  }
>>
>> +static int meson_pinconf_set_drive_strength(struct meson_pinctrl *pc,
>> +                                           unsigned int pin,
>> +                                           u16 drive_strength_ua)
>> +{
>> +       struct meson_bank *bank;
>> +       unsigned int reg, bit;
>> +       unsigned int ds_val;
> you can move ds_val to the line above
>
> [...]
>> +       if (!pc->reg_ds) {
>> +               dev_err(pc->dev, "drive-strength not supported\n");
> I'm getting this on one of my Meson8m2 boards:
> $ # cat /sys/kernel/debug/pinctrl/c1109880.pinctrl-pinctrl-meson/pinconf-pins
> ...
> [  874.748531] meson8-pinctrl c1109880.pinctrl: drive-strength not supported
> [  874.755278] meson8-pinctrl c1109880.pinctrl: drive-strength not supported
> [  874.762086] meson8-pinctrl c1109880.pinctrl: drive-strength not supported
> Pin config settings per pin
> Format: pin (name): configs
> pin 0 (GPIOX_0): input bias disabled
> pin 1 (GPIOX_1): input bias disabled
> pin 2 (GPIOX_2): input bias disabled
> ...
>
> I believe we are not supposed to complain when getting the
> drive-strength when reg_ds is absent.
> all pre-G12A SoCs don't have reg_ds, so we don't need to error-out in
> that case (because that's perfectly valid)
>
> [...]
>> +static int meson_pinconf_get_drive_strength(struct meson_pinctrl *pc,
>> +                                           unsigned int pin,
>> +                                           u16 *drive_strength_ua)
>> +{
>> +       struct meson_bank *bank;
>> +       unsigned int reg, bit;
>> +       unsigned int val;
>> +       int ret;
>> +
>> +       if (!pc->reg_ds) {
>> +               dev_err(pc->dev, "drive-strength not supported\n");
> based on your previous explanation (that you want to inform the .dts
> author that he's doing something wrong) I'm happy with this error if
> Linus W. doesn't veto this.
>
>
> Regards
> Martin


Guillaume


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

  reply index

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-07 11:57 [PATCH v3 0/6] Add drive-strength in Meson pinctrl driver Guillaume La Roque
2019-05-07 11:57 ` [PATCH v3 1/6] dt-bindings: pinctrl: add a 'drive-strength-microamp' property Guillaume La Roque
2019-05-07 17:37   ` Martin Blumenstingl
2019-05-07 11:57 ` [PATCH v3 2/6] pinctrl: generic: add new 'drive-strength-microamp' property support Guillaume La Roque
2019-05-07 11:57 ` [PATCH v3 3/6] dt-bindings: pinctrl: meson: Add drive-strength-microamp property Guillaume La Roque
2019-05-07 17:37   ` Martin Blumenstingl
2019-05-07 11:57 ` [PATCH v3 4/6] pinctrl: meson: Rework enable/disable bias part Guillaume La Roque
2019-05-07 17:53   ` Martin Blumenstingl
2019-05-09 11:25     ` guillaume La Roque
2019-05-07 11:57 ` [PATCH v3 5/6] pinctrl: meson: add support of drive-strength-microamp Guillaume La Roque
2019-05-07 18:18   ` Martin Blumenstingl
2019-05-09 11:23     ` guillaume La Roque [this message]
2019-05-07 11:57 ` [PATCH v3 6/6] pinctrl: meson: g12a: add DS bank value Guillaume La Roque
2019-05-07 18:09   ` Martin Blumenstingl
2019-05-07 15:45 ` [PATCH v3 0/6] Add drive-strength in Meson pinctrl driver Jerome Brunet
2019-05-07 18:03 ` Martin Blumenstingl

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4e44984f-eb76-87d1-e458-506bcccf1500@baylibre.com \
    --to=glaroque@baylibre.com \
    --cc=devicetree@vger.kernel.org \
    --cc=khilman@baylibre.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=martin.blumenstingl@googlemail.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Amlogic Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-amlogic/0 linux-amlogic/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-amlogic linux-amlogic/ https://lore.kernel.org/linux-amlogic \
		linux-amlogic@lists.infradead.org linux-amlogic@archiver.kernel.org
	public-inbox-index linux-amlogic


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-amlogic


AGPL code for this site: git clone https://public-inbox.org/ public-inbox