Hanjie Lin <hanjie.lin@amlogic.com> writes:

> This patchset adds support for USB on Amlogic A1 SoCs.
>
> This patchset is composed with :
> - bindings of the PHY
> - bindings of the USB Control Glue
> - PHY Driver
> - USB Control Glue driver
> - dts of the PHY
> - dts of the USB Controller
>
> The Amlogic A1 USB Complex is composed of :
> - 1 DWC3 USB controller for USB2 Host functionality
> - 1 USB2 PHY for USB2 Host functionality
>
> The USB Control Glue setups the clocks and the reset about DWC3 USB
> controller, and binds to the USB2 PHY. It also configures the 8bit
> UTMI interfaces for the USB2 PHY, including setting USB2 phy mode.
>
> The USB2 PHY driver initializes the phy analog settings, phy PLL 
> setup and phy tuning.
>
> This patchset is based on A1 clock/power domain/reset series at [0].
>
> Changes since v1:[1]
>  - integrate glue and phy drivers into g12a's
>  
> Changes since v2:[2]
>  - modify amlogic,meson-g12a-usb-ctrl.yaml with dt_binding_check tool
>  - phy/glue driver use of_device_get_match_data to distinguish A1 from G12A
>
> Changes since v3:[3]
>  - fix bindings mistakes of the PHY according Rob's comments
>  - fix bindings mistakes of the USB Control Glue according Rob's comments
>  - phy driver add xtal_usb_phy clock which moved from glue driver
>  - glue driver use otg_mode instead of soc_id to support otg function
>
> Changes since v4:[4]
>  - phy driver revert reset-names changes
>  - phy driver change clock name to "xtal" to consistent with g12a
>  - glue driver add drvdata otg_switch_supported
>
> Changes since v5:[5]
>  - integrate phy bindings into g12a
>  - modify glue bindings format according to martin's advices
>  - glue driver add dwc3_meson_g12a_otg_init() do otg related work
>  - glue driver add clk_bulk_disable_unprepare() in remove
>
> Changes since v6:[6]
>  - fix glue bindings dt_check_bindings error.
>  - squash phy and glue dts patches and set usb status to disabled default
>  
> [0]
> https://patchwork.kernel.org/project/linux-amlogic/list/?series=185477
> https://patchwork.kernel.org/project/linux-amlogic/list/?series=180055
> https://patchwork.kernel.org/project/linux-amlogic/list/?series=189643
>
> [1] : https://lore.kernel.org/linux-amlogic/1574405757-76184-1-git-send-email-hanjie.lin@amlogic.com
>
> [2] : https://lore.kernel.org/linux-amlogic/1576636944-196192-1-git-send-email-hanjie.lin@amlogic.com
>
> [3] : https://lore.kernel.org/linux-amlogic/1577428606-69855-1-git-send-email-hanjie.lin@amlogic.com
>
> [4] : https://lore.kernel.org/linux-amlogic/1578537045-23260-1-git-send-email-hanjie.lin@amlogic.com
>
> [5] : https://lore.kernel.org/linux-amlogic/1578634957-54826-1-git-send-email-hanjie.lin@amlogic.com
>
> [6] : https://lore.kernel.org/linux-amlogic/1579220504-110067-1-git-send-email-hanjie.lin@amlogic.com
>
> Hanjie Lin (5):
>   dt-bindings: phy: Add Amlogic A1 USB2 PHY Bindings
>   dt-bindings: usb: dwc3: Add the Amlogic A1 Family DWC3 Glue Bindings
>   phy: amlogic: Add Amlogic A1 USB2 PHY Driver
>   usb: dwc3: Add Amlogic A1 DWC3 glue
>   arm64: dts: meson: a1: Enable USB2 PHY and DWC3 controller

I have taken dwc3 bindings and dwc3 patch. PHY parts should go via Kishon

-- 
balbi