* brcmfmac and unaligned sdio access on Khadas VIM3L [not found] <CGME20210209124819eucas1p29c9b481ef524a753ce79aa6ab580d0a7@eucas1p2.samsung.com> @ 2021-02-09 12:48 ` Marek Szyprowski 2021-02-10 8:17 ` Neil Armstrong 0 siblings, 1 reply; 6+ messages in thread From: Marek Szyprowski @ 2021-02-09 12:48 UTC (permalink / raw) To: linux-wireless, brcm80211-dev-list.pdl, linux-amlogic, linux-mmc Cc: Arend van Spriel, Chung-hsien Hsu, Bartlomiej Zolnierkiewicz, martin.blumenstingl, Dmitry Lebed, Hante Meuleman, Wright Feng, Chi-hsien Lin, Heiner Kallweit, Franky Lin Hi I've noticed that the Broadcom Wifi chip performs unaligned SDIO access during the station scan on Khadas VIM3l board. This issue went unnoticed so far, because there was a workaround in the meson MMC driver, which has been recently disabled by commit e085b51c74cc ("mmc: meson-gx: check for scatterlist size alignment in block mode") from current linux-next. I can easily reproduce this issue with the following commands: # dmesg | grep brcm [ 11.659351] Bluetooth: hci0: BCM4359C0 'brcm/BCM4359C0.hcd' Patch [ 13.079767] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4359-sdio for chip BCM4359/9 [ 13.527363] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4359-sdio for chip BCM4359/9 [ 13.601269] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-11), device may have limited channels available [ 13.619414] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4359/9 wl0: Mar 6 2017 10:16:06 version 9.87.51.7 (r686312) FWID 01-4dcc75d9 # ifconfig wlan0 up [ 208.052058] ieee80211 phy0: brcmf_dongle_roam: WLC_SET_ROAM_TRIGGER error (-52) # iw wlan0 scan >/dev/null [ 218.148345] ------------[ cut here ]------------ [ 218.148501] unaligned sg len 504 blksize 256 [ 218.153712] WARNING: CPU: 1 PID: 75 at drivers/mmc/host/meson-gx-mmc.c:251 meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 [ 218.162616] Modules linked in: ipv6 brcmfmac brcmutil cfg80211 dw_hdmi_cec dw_hdmi_i2s_audio hci_uart btqca btbcm bluetooth ecdh_generic ecc crct10dif_ce rfkill panfrost snd_soc_meson_axg_sound_card snd_soc_meson_card_utils gpu_sched meson_gxbb_wdt rtc_hym8563 pwm_meson meson_gxl rtc_meson_vrtc rc_khadas meson_ir reset_meson_audio_arb realtek snd_soc_meson_g12a_tohdmitx snd_soc_meson_codec_glue snd_soc_meson_axg_tdmout snd_soc_meson_axg_frddr snd_soc_meson_axg_fifo axg_audio sclk_div clk_phase mdio_mux_meson_g12a meson_dw_hdmi meson_drm meson_rng dwmac_generic snd_soc_meson_axg_tdm_interface meson_canvas rng_core dw_hdmi snd_soc_meson_axg_tdm_formatter dwmac_meson8b stmmac_platform stmmac display_connector adc_keys pcs_xpcs nvmem_meson_efuse [ 218.228329] CPU: 1 PID: 75 Comm: kworker/u8:2 Not tainted 5.11.0-rc6-next-20210208 #2492 [ 218.236343] Hardware name: Khadas VIM3L (DT) [ 218.240579] Workqueue: brcmf_wq/mmc2:0001:1 brcmf_sdio_dataworker [brcmfmac] [ 218.247559] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) [ 218.253506] pc : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 [ 218.259372] lr : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 [ 218.265237] sp : ffff80001327b870 [ 218.268514] x29: ffff80001327b870 x28: 0000000000000003 [ 218.273776] x27: 0000000000000218 x26: 0000000000000600 [ 218.279036] x25: ffff000003a17678 x24: 0000000000000000 [ 218.284296] x23: ffff8000121cfae8 x22: ffff800011b54000 [ 218.289559] x21: ffff80001327bb18 x20: ffff00000277d000 [ 218.294819] x19: ffff80001327ba40 x18: 00000002faf07f80 [ 218.300081] x17: 0000000000004000 x16: 0000000000000000 [ 218.305341] x15: 0000000000000380 x14: 0000000000000000 [ 218.310603] x13: 0000000000000080 x12: 0000000000000000 [ 218.315865] x11: 0000000000000000 x10: 0000000000001370 [ 218.321125] x9 : ffff00006f995258 x8 : 000000009e0e7ca7 [ 218.326387] x7 : ffff80001327b4a0 x6 : 0000000000000001 [ 218.331648] x5 : 0000000000000001 x4 : 0000000000000000 [ 218.336912] x3 : 0000000000000002 x2 : ffff8000121f4768 [ 218.342171] x1 : 42fe1bd05e5eaa00 x0 : 0000000000000000 [ 218.347435] Call trace: [ 218.349854] meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 [ 218.355368] meson_mmc_request+0x74/0xb0 [ 218.359250] __mmc_start_request+0xa4/0x2b0 [ 218.363390] mmc_start_request+0x80/0xa8 [ 218.367272] mmc_wait_for_req+0x68/0xd8 [ 218.371066] mmc_submit_one.isra.17+0x78/0x148 [brcmfmac] [ 218.376416] brcmf_sdiod_sglist_rw+0x324/0x4a8 [brcmfmac] [ 218.381762] brcmf_sdiod_recv_chain+0x70/0x140 [brcmfmac] [ 218.387110] brcmf_sdio_dataworker+0x614/0x17d0 [brcmfmac] [ 218.392545] process_one_work+0x2a8/0x728 [ 218.396510] worker_thread+0x48/0x460 [ 218.400132] kthread+0x134/0x160 [ 218.403323] ret_from_fork+0x10/0x18 [ 218.406862] irq event stamp: 15834 [ 218.410222] hardirqs last enabled at (15833): [<ffff800010f95804>] _raw_spin_unlock_irq+0x3c/0x80 [ 218.419107] hardirqs last disabled at (15834): [<ffff800010f895ac>] el1_dbg+0x24/0x50 [ 218.426869] softirqs last enabled at (15828): [<ffff800010010508>] _stext+0x508/0x638 [ 218.434717] softirqs last disabled at (15823): [<ffff8000100952ec>] irq_exit+0x19c/0x1a8 [ 218.442739] ---[ end trace dfc38bb4458b4c37 ]--- # Surprisingly the same commands executed on the Khadas VIM3 board with the same kernel don't trigger the warning. Let me know if I can help debugging this issue. Best regards -- Marek Szyprowski, PhD Samsung R&D Institute Poland _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac and unaligned sdio access on Khadas VIM3L 2021-02-09 12:48 ` brcmfmac and unaligned sdio access on Khadas VIM3L Marek Szyprowski @ 2021-02-10 8:17 ` Neil Armstrong 2021-02-10 8:45 ` Marek Szyprowski 0 siblings, 1 reply; 6+ messages in thread From: Neil Armstrong @ 2021-02-10 8:17 UTC (permalink / raw) To: Marek Szyprowski, linux-wireless, brcm80211-dev-list.pdl, linux-amlogic, linux-mmc Cc: Arend van Spriel, Chung-hsien Hsu, Bartlomiej Zolnierkiewicz, martin.blumenstingl, Chi-hsien Lin, Dmitry Lebed, Hante Meuleman, Wright Feng, Franky Lin, Heiner Kallweit Hi, On 09/02/2021 13:48, Marek Szyprowski wrote: > Hi > > I've noticed that the Broadcom Wifi chip performs unaligned SDIO access > during the station scan on Khadas VIM3l board. This issue went unnoticed > so far, because there was a workaround in the meson MMC driver, which > has been recently disabled by commit e085b51c74cc ("mmc: meson-gx: check > for scatterlist size alignment in block mode") from current linux-next. > > I can easily reproduce this issue with the following commands: > > # dmesg | grep brcm > [ 11.659351] Bluetooth: hci0: BCM4359C0 'brcm/BCM4359C0.hcd' Patch > [ 13.079767] brcmfmac: brcmf_fw_alloc_request: using > brcm/brcmfmac4359-sdio for chip BCM4359/9 > [ 13.527363] brcmfmac: brcmf_fw_alloc_request: using > brcm/brcmfmac4359-sdio for chip BCM4359/9 > [ 13.601269] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available > (err=-11), device may have limited channels available > [ 13.619414] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4359/9 wl0: > Mar 6 2017 10:16:06 version 9.87.51.7 (r686312) FWID 01-4dcc75d9 > # ifconfig wlan0 up > [ 208.052058] ieee80211 phy0: brcmf_dongle_roam: WLC_SET_ROAM_TRIGGER > error (-52) > # iw wlan0 scan >/dev/null > [ 218.148345] ------------[ cut here ]------------ > [ 218.148501] unaligned sg len 504 blksize 256 > [ 218.153712] WARNING: CPU: 1 PID: 75 at > drivers/mmc/host/meson-gx-mmc.c:251 > meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 > [ 218.162616] Modules linked in: ipv6 brcmfmac brcmutil cfg80211 > dw_hdmi_cec dw_hdmi_i2s_audio hci_uart btqca btbcm bluetooth > ecdh_generic ecc crct10dif_ce rfkill panfrost > snd_soc_meson_axg_sound_card snd_soc_meson_card_utils gpu_sched > meson_gxbb_wdt rtc_hym8563 pwm_meson meson_gxl rtc_meson_vrtc rc_khadas > meson_ir reset_meson_audio_arb realtek snd_soc_meson_g12a_tohdmitx > snd_soc_meson_codec_glue snd_soc_meson_axg_tdmout > snd_soc_meson_axg_frddr snd_soc_meson_axg_fifo axg_audio sclk_div > clk_phase mdio_mux_meson_g12a meson_dw_hdmi meson_drm meson_rng > dwmac_generic snd_soc_meson_axg_tdm_interface meson_canvas rng_core > dw_hdmi snd_soc_meson_axg_tdm_formatter dwmac_meson8b stmmac_platform > stmmac display_connector adc_keys pcs_xpcs nvmem_meson_efuse > [ 218.228329] CPU: 1 PID: 75 Comm: kworker/u8:2 Not tainted > 5.11.0-rc6-next-20210208 #2492 > [ 218.236343] Hardware name: Khadas VIM3L (DT) > [ 218.240579] Workqueue: brcmf_wq/mmc2:0001:1 brcmf_sdio_dataworker > [brcmfmac] > [ 218.247559] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) > [ 218.253506] pc : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 > [ 218.259372] lr : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 > [ 218.265237] sp : ffff80001327b870 > [ 218.268514] x29: ffff80001327b870 x28: 0000000000000003 > [ 218.273776] x27: 0000000000000218 x26: 0000000000000600 > [ 218.279036] x25: ffff000003a17678 x24: 0000000000000000 > [ 218.284296] x23: ffff8000121cfae8 x22: ffff800011b54000 > [ 218.289559] x21: ffff80001327bb18 x20: ffff00000277d000 > [ 218.294819] x19: ffff80001327ba40 x18: 00000002faf07f80 > [ 218.300081] x17: 0000000000004000 x16: 0000000000000000 > [ 218.305341] x15: 0000000000000380 x14: 0000000000000000 > [ 218.310603] x13: 0000000000000080 x12: 0000000000000000 > [ 218.315865] x11: 0000000000000000 x10: 0000000000001370 > [ 218.321125] x9 : ffff00006f995258 x8 : 000000009e0e7ca7 > [ 218.326387] x7 : ffff80001327b4a0 x6 : 0000000000000001 > [ 218.331648] x5 : 0000000000000001 x4 : 0000000000000000 > [ 218.336912] x3 : 0000000000000002 x2 : ffff8000121f4768 > [ 218.342171] x1 : 42fe1bd05e5eaa00 x0 : 0000000000000000 > [ 218.347435] Call trace: > [ 218.349854] meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 > [ 218.355368] meson_mmc_request+0x74/0xb0 > [ 218.359250] __mmc_start_request+0xa4/0x2b0 > [ 218.363390] mmc_start_request+0x80/0xa8 > [ 218.367272] mmc_wait_for_req+0x68/0xd8 > [ 218.371066] mmc_submit_one.isra.17+0x78/0x148 [brcmfmac] > [ 218.376416] brcmf_sdiod_sglist_rw+0x324/0x4a8 [brcmfmac] > [ 218.381762] brcmf_sdiod_recv_chain+0x70/0x140 [brcmfmac] > [ 218.387110] brcmf_sdio_dataworker+0x614/0x17d0 [brcmfmac] > [ 218.392545] process_one_work+0x2a8/0x728 > [ 218.396510] worker_thread+0x48/0x460 > [ 218.400132] kthread+0x134/0x160 > [ 218.403323] ret_from_fork+0x10/0x18 > [ 218.406862] irq event stamp: 15834 > [ 218.410222] hardirqs last enabled at (15833): [<ffff800010f95804>] > _raw_spin_unlock_irq+0x3c/0x80 > [ 218.419107] hardirqs last disabled at (15834): [<ffff800010f895ac>] > el1_dbg+0x24/0x50 > [ 218.426869] softirqs last enabled at (15828): [<ffff800010010508>] > _stext+0x508/0x638 > [ 218.434717] softirqs last disabled at (15823): [<ffff8000100952ec>] > irq_exit+0x19c/0x1a8 > [ 218.442739] ---[ end trace dfc38bb4458b4c37 ]--- > # > > Surprisingly the same commands executed on the Khadas VIM3 board with > the same kernel don't trigger the warning. This may be because the VIM3 (G12A & G12B) has a broken SDIO controller using an internal SRAM as bounce buffer instead of the scatter/gather DMA, cf amlogic,dram-access-quirk. > > Let me know if I can help debugging this issue. Simply remove the WARN_ONCE()... > > Best regards > Thanks for the report, Neil _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac and unaligned sdio access on Khadas VIM3L 2021-02-10 8:17 ` Neil Armstrong @ 2021-02-10 8:45 ` Marek Szyprowski 2021-02-10 8:52 ` Neil Armstrong 0 siblings, 1 reply; 6+ messages in thread From: Marek Szyprowski @ 2021-02-10 8:45 UTC (permalink / raw) To: Neil Armstrong, linux-wireless, brcm80211-dev-list.pdl, linux-amlogic, linux-mmc Cc: Arend van Spriel, Chung-hsien Hsu, Bartlomiej Zolnierkiewicz, martin.blumenstingl, Chi-hsien Lin, Dmitry Lebed, Hante Meuleman, Wright Feng, Franky Lin, Heiner Kallweit Hi Neil, On 10.02.2021 09:17, Neil Armstrong wrote: > On 09/02/2021 13:48, Marek Szyprowski wrote: >> I've noticed that the Broadcom Wifi chip performs unaligned SDIO access >> during the station scan on Khadas VIM3l board. This issue went unnoticed >> so far, because there was a workaround in the meson MMC driver, which >> has been recently disabled by commit e085b51c74cc ("mmc: meson-gx: check >> for scatterlist size alignment in block mode") from current linux-next. >> >> I can easily reproduce this issue with the following commands: >> >> # dmesg | grep brcm >> [ 11.659351] Bluetooth: hci0: BCM4359C0 'brcm/BCM4359C0.hcd' Patch >> [ 13.079767] brcmfmac: brcmf_fw_alloc_request: using >> brcm/brcmfmac4359-sdio for chip BCM4359/9 >> [ 13.527363] brcmfmac: brcmf_fw_alloc_request: using >> brcm/brcmfmac4359-sdio for chip BCM4359/9 >> [ 13.601269] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available >> (err=-11), device may have limited channels available >> [ 13.619414] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4359/9 wl0: >> Mar 6 2017 10:16:06 version 9.87.51.7 (r686312) FWID 01-4dcc75d9 >> # ifconfig wlan0 up >> [ 208.052058] ieee80211 phy0: brcmf_dongle_roam: WLC_SET_ROAM_TRIGGER >> error (-52) >> # iw wlan0 scan >/dev/null >> [ 218.148345] ------------[ cut here ]------------ >> [ 218.148501] unaligned sg len 504 blksize 256 >> [ 218.153712] WARNING: CPU: 1 PID: 75 at >> drivers/mmc/host/meson-gx-mmc.c:251 >> meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >> [ 218.162616] Modules linked in: ipv6 brcmfmac brcmutil cfg80211 >> dw_hdmi_cec dw_hdmi_i2s_audio hci_uart btqca btbcm bluetooth >> ecdh_generic ecc crct10dif_ce rfkill panfrost >> snd_soc_meson_axg_sound_card snd_soc_meson_card_utils gpu_sched >> meson_gxbb_wdt rtc_hym8563 pwm_meson meson_gxl rtc_meson_vrtc rc_khadas >> meson_ir reset_meson_audio_arb realtek snd_soc_meson_g12a_tohdmitx >> snd_soc_meson_codec_glue snd_soc_meson_axg_tdmout >> snd_soc_meson_axg_frddr snd_soc_meson_axg_fifo axg_audio sclk_div >> clk_phase mdio_mux_meson_g12a meson_dw_hdmi meson_drm meson_rng >> dwmac_generic snd_soc_meson_axg_tdm_interface meson_canvas rng_core >> dw_hdmi snd_soc_meson_axg_tdm_formatter dwmac_meson8b stmmac_platform >> stmmac display_connector adc_keys pcs_xpcs nvmem_meson_efuse >> [ 218.228329] CPU: 1 PID: 75 Comm: kworker/u8:2 Not tainted >> 5.11.0-rc6-next-20210208 #2492 >> [ 218.236343] Hardware name: Khadas VIM3L (DT) >> [ 218.240579] Workqueue: brcmf_wq/mmc2:0001:1 brcmf_sdio_dataworker >> [brcmfmac] >> [ 218.247559] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) >> [ 218.253506] pc : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >> [ 218.259372] lr : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >> [ 218.265237] sp : ffff80001327b870 >> [ 218.268514] x29: ffff80001327b870 x28: 0000000000000003 >> [ 218.273776] x27: 0000000000000218 x26: 0000000000000600 >> [ 218.279036] x25: ffff000003a17678 x24: 0000000000000000 >> [ 218.284296] x23: ffff8000121cfae8 x22: ffff800011b54000 >> [ 218.289559] x21: ffff80001327bb18 x20: ffff00000277d000 >> [ 218.294819] x19: ffff80001327ba40 x18: 00000002faf07f80 >> [ 218.300081] x17: 0000000000004000 x16: 0000000000000000 >> [ 218.305341] x15: 0000000000000380 x14: 0000000000000000 >> [ 218.310603] x13: 0000000000000080 x12: 0000000000000000 >> [ 218.315865] x11: 0000000000000000 x10: 0000000000001370 >> [ 218.321125] x9 : ffff00006f995258 x8 : 000000009e0e7ca7 >> [ 218.326387] x7 : ffff80001327b4a0 x6 : 0000000000000001 >> [ 218.331648] x5 : 0000000000000001 x4 : 0000000000000000 >> [ 218.336912] x3 : 0000000000000002 x2 : ffff8000121f4768 >> [ 218.342171] x1 : 42fe1bd05e5eaa00 x0 : 0000000000000000 >> [ 218.347435] Call trace: >> [ 218.349854] meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >> [ 218.355368] meson_mmc_request+0x74/0xb0 >> [ 218.359250] __mmc_start_request+0xa4/0x2b0 >> [ 218.363390] mmc_start_request+0x80/0xa8 >> [ 218.367272] mmc_wait_for_req+0x68/0xd8 >> [ 218.371066] mmc_submit_one.isra.17+0x78/0x148 [brcmfmac] >> [ 218.376416] brcmf_sdiod_sglist_rw+0x324/0x4a8 [brcmfmac] >> [ 218.381762] brcmf_sdiod_recv_chain+0x70/0x140 [brcmfmac] >> [ 218.387110] brcmf_sdio_dataworker+0x614/0x17d0 [brcmfmac] >> [ 218.392545] process_one_work+0x2a8/0x728 >> [ 218.396510] worker_thread+0x48/0x460 >> [ 218.400132] kthread+0x134/0x160 >> [ 218.403323] ret_from_fork+0x10/0x18 >> [ 218.406862] irq event stamp: 15834 >> [ 218.410222] hardirqs last enabled at (15833): [<ffff800010f95804>] >> _raw_spin_unlock_irq+0x3c/0x80 >> [ 218.419107] hardirqs last disabled at (15834): [<ffff800010f895ac>] >> el1_dbg+0x24/0x50 >> [ 218.426869] softirqs last enabled at (15828): [<ffff800010010508>] >> _stext+0x508/0x638 >> [ 218.434717] softirqs last disabled at (15823): [<ffff8000100952ec>] >> irq_exit+0x19c/0x1a8 >> [ 218.442739] ---[ end trace dfc38bb4458b4c37 ]--- >> # >> >> Surprisingly the same commands executed on the Khadas VIM3 board with >> the same kernel don't trigger the warning. > This may be because the VIM3 (G12A & G12B) has a broken SDIO controller using > an internal SRAM as bounce buffer instead of the scatter/gather DMA, cf amlogic,dram-access-quirk. Good to know, this explains why it works without an issue on VIM3. >> Let me know if I can help debugging this issue. > Simply remove the WARN_ONCE()... Well, that WARN is not a big issue for me. I just wanted to help fixing the real issue. If I understand right, the brcmfmac driver queues incorrectly prepared sd list for the given transfer mode, what should be fixed there. On the other hand, if this is just a limitation of the meson mmc controller on SM1/VIM3l, then imho there should not be a WARN there and maybe the mentioned 'amlogic,dram-access-quirk' could be used to fix the issue on VIM3l too. I've checked and it indeed 'fixes' the issue on that board. Best regards -- Marek Szyprowski, PhD Samsung R&D Institute Poland _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac and unaligned sdio access on Khadas VIM3L 2021-02-10 8:45 ` Marek Szyprowski @ 2021-02-10 8:52 ` Neil Armstrong 2021-04-07 8:45 ` Neil Armstrong 0 siblings, 1 reply; 6+ messages in thread From: Neil Armstrong @ 2021-02-10 8:52 UTC (permalink / raw) To: Marek Szyprowski, linux-wireless, brcm80211-dev-list.pdl, linux-amlogic, linux-mmc Cc: Arend van Spriel, Chung-hsien Hsu, Bartlomiej Zolnierkiewicz, martin.blumenstingl, Chi-hsien Lin, Dmitry Lebed, Hante Meuleman, Wright Feng, Franky Lin, Heiner Kallweit On 10/02/2021 09:45, Marek Szyprowski wrote: > Hi Neil, > > On 10.02.2021 09:17, Neil Armstrong wrote: >> On 09/02/2021 13:48, Marek Szyprowski wrote: >>> I've noticed that the Broadcom Wifi chip performs unaligned SDIO access >>> during the station scan on Khadas VIM3l board. This issue went unnoticed >>> so far, because there was a workaround in the meson MMC driver, which >>> has been recently disabled by commit e085b51c74cc ("mmc: meson-gx: check >>> for scatterlist size alignment in block mode") from current linux-next. >>> >>> I can easily reproduce this issue with the following commands: >>> >>> # dmesg | grep brcm >>> [ 11.659351] Bluetooth: hci0: BCM4359C0 'brcm/BCM4359C0.hcd' Patch >>> [ 13.079767] brcmfmac: brcmf_fw_alloc_request: using >>> brcm/brcmfmac4359-sdio for chip BCM4359/9 >>> [ 13.527363] brcmfmac: brcmf_fw_alloc_request: using >>> brcm/brcmfmac4359-sdio for chip BCM4359/9 >>> [ 13.601269] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available >>> (err=-11), device may have limited channels available >>> [ 13.619414] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4359/9 wl0: >>> Mar 6 2017 10:16:06 version 9.87.51.7 (r686312) FWID 01-4dcc75d9 >>> # ifconfig wlan0 up >>> [ 208.052058] ieee80211 phy0: brcmf_dongle_roam: WLC_SET_ROAM_TRIGGER >>> error (-52) >>> # iw wlan0 scan >/dev/null >>> [ 218.148345] ------------[ cut here ]------------ >>> [ 218.148501] unaligned sg len 504 blksize 256 >>> [ 218.153712] WARNING: CPU: 1 PID: 75 at >>> drivers/mmc/host/meson-gx-mmc.c:251 >>> meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>> [ 218.162616] Modules linked in: ipv6 brcmfmac brcmutil cfg80211 >>> dw_hdmi_cec dw_hdmi_i2s_audio hci_uart btqca btbcm bluetooth >>> ecdh_generic ecc crct10dif_ce rfkill panfrost >>> snd_soc_meson_axg_sound_card snd_soc_meson_card_utils gpu_sched >>> meson_gxbb_wdt rtc_hym8563 pwm_meson meson_gxl rtc_meson_vrtc rc_khadas >>> meson_ir reset_meson_audio_arb realtek snd_soc_meson_g12a_tohdmitx >>> snd_soc_meson_codec_glue snd_soc_meson_axg_tdmout >>> snd_soc_meson_axg_frddr snd_soc_meson_axg_fifo axg_audio sclk_div >>> clk_phase mdio_mux_meson_g12a meson_dw_hdmi meson_drm meson_rng >>> dwmac_generic snd_soc_meson_axg_tdm_interface meson_canvas rng_core >>> dw_hdmi snd_soc_meson_axg_tdm_formatter dwmac_meson8b stmmac_platform >>> stmmac display_connector adc_keys pcs_xpcs nvmem_meson_efuse >>> [ 218.228329] CPU: 1 PID: 75 Comm: kworker/u8:2 Not tainted >>> 5.11.0-rc6-next-20210208 #2492 >>> [ 218.236343] Hardware name: Khadas VIM3L (DT) >>> [ 218.240579] Workqueue: brcmf_wq/mmc2:0001:1 brcmf_sdio_dataworker >>> [brcmfmac] >>> [ 218.247559] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) >>> [ 218.253506] pc : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>> [ 218.259372] lr : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>> [ 218.265237] sp : ffff80001327b870 >>> [ 218.268514] x29: ffff80001327b870 x28: 0000000000000003 >>> [ 218.273776] x27: 0000000000000218 x26: 0000000000000600 >>> [ 218.279036] x25: ffff000003a17678 x24: 0000000000000000 >>> [ 218.284296] x23: ffff8000121cfae8 x22: ffff800011b54000 >>> [ 218.289559] x21: ffff80001327bb18 x20: ffff00000277d000 >>> [ 218.294819] x19: ffff80001327ba40 x18: 00000002faf07f80 >>> [ 218.300081] x17: 0000000000004000 x16: 0000000000000000 >>> [ 218.305341] x15: 0000000000000380 x14: 0000000000000000 >>> [ 218.310603] x13: 0000000000000080 x12: 0000000000000000 >>> [ 218.315865] x11: 0000000000000000 x10: 0000000000001370 >>> [ 218.321125] x9 : ffff00006f995258 x8 : 000000009e0e7ca7 >>> [ 218.326387] x7 : ffff80001327b4a0 x6 : 0000000000000001 >>> [ 218.331648] x5 : 0000000000000001 x4 : 0000000000000000 >>> [ 218.336912] x3 : 0000000000000002 x2 : ffff8000121f4768 >>> [ 218.342171] x1 : 42fe1bd05e5eaa00 x0 : 0000000000000000 >>> [ 218.347435] Call trace: >>> [ 218.349854] meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>> [ 218.355368] meson_mmc_request+0x74/0xb0 >>> [ 218.359250] __mmc_start_request+0xa4/0x2b0 >>> [ 218.363390] mmc_start_request+0x80/0xa8 >>> [ 218.367272] mmc_wait_for_req+0x68/0xd8 >>> [ 218.371066] mmc_submit_one.isra.17+0x78/0x148 [brcmfmac] >>> [ 218.376416] brcmf_sdiod_sglist_rw+0x324/0x4a8 [brcmfmac] >>> [ 218.381762] brcmf_sdiod_recv_chain+0x70/0x140 [brcmfmac] >>> [ 218.387110] brcmf_sdio_dataworker+0x614/0x17d0 [brcmfmac] >>> [ 218.392545] process_one_work+0x2a8/0x728 >>> [ 218.396510] worker_thread+0x48/0x460 >>> [ 218.400132] kthread+0x134/0x160 >>> [ 218.403323] ret_from_fork+0x10/0x18 >>> [ 218.406862] irq event stamp: 15834 >>> [ 218.410222] hardirqs last enabled at (15833): [<ffff800010f95804>] >>> _raw_spin_unlock_irq+0x3c/0x80 >>> [ 218.419107] hardirqs last disabled at (15834): [<ffff800010f895ac>] >>> el1_dbg+0x24/0x50 >>> [ 218.426869] softirqs last enabled at (15828): [<ffff800010010508>] >>> _stext+0x508/0x638 >>> [ 218.434717] softirqs last disabled at (15823): [<ffff8000100952ec>] >>> irq_exit+0x19c/0x1a8 >>> [ 218.442739] ---[ end trace dfc38bb4458b4c37 ]--- >>> # >>> >>> Surprisingly the same commands executed on the Khadas VIM3 board with >>> the same kernel don't trigger the warning. >> This may be because the VIM3 (G12A & G12B) has a broken SDIO controller using >> an internal SRAM as bounce buffer instead of the scatter/gather DMA, cf amlogic,dram-access-quirk. > Good to know, this explains why it works without an issue on VIM3. >>> Let me know if I can help debugging this issue. >> Simply remove the WARN_ONCE()... > > Well, that WARN is not a big issue for me. I just wanted to help fixing > the real issue. If I understand right, the brcmfmac driver queues > incorrectly prepared sd list for the given transfer mode, what should be > fixed there. I think the issue comes from brcmfmac that should not provide unaligned data, but I think it's a global issue where these kind of details aren't specified/enforced. > > On the other hand, if this is just a limitation of the meson mmc > controller on SM1/VIM3l, then imho there should not be a WARN there and > maybe the mentioned 'amlogic,dram-access-quirk' could be used to fix the > issue on VIM3l too. I've checked and it indeed 'fixes' the issue on that > board. This fix severely limits the performance so it's not a good fix here, the only fix I see here is to remove the WARN because the fact is that the DMA cannot handle unaligned data, and the SDIO device drivers should be fixed in order to achieve max performance on SDIO host drivers with DMA (it's usual to not support unaligned data when dealing with a DMA). Neil > > Best regards > _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac and unaligned sdio access on Khadas VIM3L 2021-02-10 8:52 ` Neil Armstrong @ 2021-04-07 8:45 ` Neil Armstrong 2021-04-07 10:00 ` Marek Szyprowski 0 siblings, 1 reply; 6+ messages in thread From: Neil Armstrong @ 2021-04-07 8:45 UTC (permalink / raw) To: Marek Szyprowski, linux-wireless, brcm80211-dev-list.pdl, linux-amlogic, linux-mmc Cc: Arend van Spriel, Chung-hsien Hsu, Bartlomiej Zolnierkiewicz, martin.blumenstingl, Dmitry Lebed, Hante Meuleman, Wright Feng, Chi-hsien Lin, Heiner Kallweit, Franky Lin Hi Marek, On 10/02/2021 09:52, Neil Armstrong wrote: > On 10/02/2021 09:45, Marek Szyprowski wrote: >> Hi Neil, >> >> On 10.02.2021 09:17, Neil Armstrong wrote: >>> On 09/02/2021 13:48, Marek Szyprowski wrote: >>>> I've noticed that the Broadcom Wifi chip performs unaligned SDIO access >>>> during the station scan on Khadas VIM3l board. This issue went unnoticed >>>> so far, because there was a workaround in the meson MMC driver, which >>>> has been recently disabled by commit e085b51c74cc ("mmc: meson-gx: check >>>> for scatterlist size alignment in block mode") from current linux-next. >>>> >>>> I can easily reproduce this issue with the following commands: >>>> >>>> # dmesg | grep brcm >>>> [ 11.659351] Bluetooth: hci0: BCM4359C0 'brcm/BCM4359C0.hcd' Patch >>>> [ 13.079767] brcmfmac: brcmf_fw_alloc_request: using >>>> brcm/brcmfmac4359-sdio for chip BCM4359/9 >>>> [ 13.527363] brcmfmac: brcmf_fw_alloc_request: using >>>> brcm/brcmfmac4359-sdio for chip BCM4359/9 >>>> [ 13.601269] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available >>>> (err=-11), device may have limited channels available >>>> [ 13.619414] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4359/9 wl0: >>>> Mar 6 2017 10:16:06 version 9.87.51.7 (r686312) FWID 01-4dcc75d9 >>>> # ifconfig wlan0 up >>>> [ 208.052058] ieee80211 phy0: brcmf_dongle_roam: WLC_SET_ROAM_TRIGGER >>>> error (-52) >>>> # iw wlan0 scan >/dev/null >>>> [ 218.148345] ------------[ cut here ]------------ >>>> [ 218.148501] unaligned sg len 504 blksize 256 >>>> [ 218.153712] WARNING: CPU: 1 PID: 75 at >>>> drivers/mmc/host/meson-gx-mmc.c:251 >>>> meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>> [ 218.162616] Modules linked in: ipv6 brcmfmac brcmutil cfg80211 >>>> dw_hdmi_cec dw_hdmi_i2s_audio hci_uart btqca btbcm bluetooth >>>> ecdh_generic ecc crct10dif_ce rfkill panfrost >>>> snd_soc_meson_axg_sound_card snd_soc_meson_card_utils gpu_sched >>>> meson_gxbb_wdt rtc_hym8563 pwm_meson meson_gxl rtc_meson_vrtc rc_khadas >>>> meson_ir reset_meson_audio_arb realtek snd_soc_meson_g12a_tohdmitx >>>> snd_soc_meson_codec_glue snd_soc_meson_axg_tdmout >>>> snd_soc_meson_axg_frddr snd_soc_meson_axg_fifo axg_audio sclk_div >>>> clk_phase mdio_mux_meson_g12a meson_dw_hdmi meson_drm meson_rng >>>> dwmac_generic snd_soc_meson_axg_tdm_interface meson_canvas rng_core >>>> dw_hdmi snd_soc_meson_axg_tdm_formatter dwmac_meson8b stmmac_platform >>>> stmmac display_connector adc_keys pcs_xpcs nvmem_meson_efuse >>>> [ 218.228329] CPU: 1 PID: 75 Comm: kworker/u8:2 Not tainted >>>> 5.11.0-rc6-next-20210208 #2492 >>>> [ 218.236343] Hardware name: Khadas VIM3L (DT) >>>> [ 218.240579] Workqueue: brcmf_wq/mmc2:0001:1 brcmf_sdio_dataworker >>>> [brcmfmac] >>>> [ 218.247559] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) >>>> [ 218.253506] pc : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>> [ 218.259372] lr : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>> [ 218.265237] sp : ffff80001327b870 >>>> [ 218.268514] x29: ffff80001327b870 x28: 0000000000000003 >>>> [ 218.273776] x27: 0000000000000218 x26: 0000000000000600 >>>> [ 218.279036] x25: ffff000003a17678 x24: 0000000000000000 >>>> [ 218.284296] x23: ffff8000121cfae8 x22: ffff800011b54000 >>>> [ 218.289559] x21: ffff80001327bb18 x20: ffff00000277d000 >>>> [ 218.294819] x19: ffff80001327ba40 x18: 00000002faf07f80 >>>> [ 218.300081] x17: 0000000000004000 x16: 0000000000000000 >>>> [ 218.305341] x15: 0000000000000380 x14: 0000000000000000 >>>> [ 218.310603] x13: 0000000000000080 x12: 0000000000000000 >>>> [ 218.315865] x11: 0000000000000000 x10: 0000000000001370 >>>> [ 218.321125] x9 : ffff00006f995258 x8 : 000000009e0e7ca7 >>>> [ 218.326387] x7 : ffff80001327b4a0 x6 : 0000000000000001 >>>> [ 218.331648] x5 : 0000000000000001 x4 : 0000000000000000 >>>> [ 218.336912] x3 : 0000000000000002 x2 : ffff8000121f4768 >>>> [ 218.342171] x1 : 42fe1bd05e5eaa00 x0 : 0000000000000000 >>>> [ 218.347435] Call trace: >>>> [ 218.349854] meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>> [ 218.355368] meson_mmc_request+0x74/0xb0 >>>> [ 218.359250] __mmc_start_request+0xa4/0x2b0 >>>> [ 218.363390] mmc_start_request+0x80/0xa8 >>>> [ 218.367272] mmc_wait_for_req+0x68/0xd8 >>>> [ 218.371066] mmc_submit_one.isra.17+0x78/0x148 [brcmfmac] >>>> [ 218.376416] brcmf_sdiod_sglist_rw+0x324/0x4a8 [brcmfmac] >>>> [ 218.381762] brcmf_sdiod_recv_chain+0x70/0x140 [brcmfmac] >>>> [ 218.387110] brcmf_sdio_dataworker+0x614/0x17d0 [brcmfmac] >>>> [ 218.392545] process_one_work+0x2a8/0x728 >>>> [ 218.396510] worker_thread+0x48/0x460 >>>> [ 218.400132] kthread+0x134/0x160 >>>> [ 218.403323] ret_from_fork+0x10/0x18 >>>> [ 218.406862] irq event stamp: 15834 >>>> [ 218.410222] hardirqs last enabled at (15833): [<ffff800010f95804>] >>>> _raw_spin_unlock_irq+0x3c/0x80 >>>> [ 218.419107] hardirqs last disabled at (15834): [<ffff800010f895ac>] >>>> el1_dbg+0x24/0x50 >>>> [ 218.426869] softirqs last enabled at (15828): [<ffff800010010508>] >>>> _stext+0x508/0x638 >>>> [ 218.434717] softirqs last disabled at (15823): [<ffff8000100952ec>] >>>> irq_exit+0x19c/0x1a8 >>>> [ 218.442739] ---[ end trace dfc38bb4458b4c37 ]--- >>>> # >>>> >>>> Surprisingly the same commands executed on the Khadas VIM3 board with >>>> the same kernel don't trigger the warning. >>> This may be because the VIM3 (G12A & G12B) has a broken SDIO controller using >>> an internal SRAM as bounce buffer instead of the scatter/gather DMA, cf amlogic,dram-access-quirk. >> Good to know, this explains why it works without an issue on VIM3. >>>> Let me know if I can help debugging this issue. >>> Simply remove the WARN_ONCE()... >> >> Well, that WARN is not a big issue for me. I just wanted to help fixing >> the real issue. If I understand right, the brcmfmac driver queues >> incorrectly prepared sd list for the given transfer mode, what should be >> fixed there. > > I think the issue comes from brcmfmac that should not provide unaligned data, > but I think it's a global issue where these kind of details aren't specified/enforced. > >> >> On the other hand, if this is just a limitation of the meson mmc >> controller on SM1/VIM3l, then imho there should not be a WARN there and >> maybe the mentioned 'amlogic,dram-access-quirk' could be used to fix the >> issue on VIM3l too. I've checked and it indeed 'fixes' the issue on that >> board. > > This fix severely limits the performance so it's not a good fix here, > the only fix I see here is to remove the WARN because the fact is that the DMA cannot handle > unaligned data, and the SDIO device drivers should be fixed in order to achieve max > performance on SDIO host drivers with DMA (it's usual to not support unaligned data > when dealing with a DMA). Do you plan to remove the warning ? I can push a quick patch if not. > > Neil > >> >> Best regards >> > _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: brcmfmac and unaligned sdio access on Khadas VIM3L 2021-04-07 8:45 ` Neil Armstrong @ 2021-04-07 10:00 ` Marek Szyprowski 0 siblings, 0 replies; 6+ messages in thread From: Marek Szyprowski @ 2021-04-07 10:00 UTC (permalink / raw) To: Neil Armstrong, linux-wireless, brcm80211-dev-list.pdl, linux-amlogic, linux-mmc Cc: Arend van Spriel, Chung-hsien Hsu, Bartlomiej Zolnierkiewicz, martin.blumenstingl, Dmitry Lebed, Hante Meuleman, Wright Feng, Chi-hsien Lin, Heiner Kallweit, Franky Lin Hi Neil, On 07.04.2021 10:45, Neil Armstrong wrote: > On 10/02/2021 09:52, Neil Armstrong wrote: >> On 10/02/2021 09:45, Marek Szyprowski wrote: >>> On 10.02.2021 09:17, Neil Armstrong wrote: >>>> On 09/02/2021 13:48, Marek Szyprowski wrote: >>>>> I've noticed that the Broadcom Wifi chip performs unaligned SDIO access >>>>> during the station scan on Khadas VIM3l board. This issue went unnoticed >>>>> so far, because there was a workaround in the meson MMC driver, which >>>>> has been recently disabled by commit e085b51c74cc ("mmc: meson-gx: check >>>>> for scatterlist size alignment in block mode") from current linux-next. >>>>> >>>>> I can easily reproduce this issue with the following commands: >>>>> >>>>> # dmesg | grep brcm >>>>> [ 11.659351] Bluetooth: hci0: BCM4359C0 'brcm/BCM4359C0.hcd' Patch >>>>> [ 13.079767] brcmfmac: brcmf_fw_alloc_request: using >>>>> brcm/brcmfmac4359-sdio for chip BCM4359/9 >>>>> [ 13.527363] brcmfmac: brcmf_fw_alloc_request: using >>>>> brcm/brcmfmac4359-sdio for chip BCM4359/9 >>>>> [ 13.601269] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available >>>>> (err=-11), device may have limited channels available >>>>> [ 13.619414] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4359/9 wl0: >>>>> Mar 6 2017 10:16:06 version 9.87.51.7 (r686312) FWID 01-4dcc75d9 >>>>> # ifconfig wlan0 up >>>>> [ 208.052058] ieee80211 phy0: brcmf_dongle_roam: WLC_SET_ROAM_TRIGGER >>>>> error (-52) >>>>> # iw wlan0 scan >/dev/null >>>>> [ 218.148345] ------------[ cut here ]------------ >>>>> [ 218.148501] unaligned sg len 504 blksize 256 >>>>> [ 218.153712] WARNING: CPU: 1 PID: 75 at >>>>> drivers/mmc/host/meson-gx-mmc.c:251 >>>>> meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>>> [ 218.162616] Modules linked in: ipv6 brcmfmac brcmutil cfg80211 >>>>> dw_hdmi_cec dw_hdmi_i2s_audio hci_uart btqca btbcm bluetooth >>>>> ecdh_generic ecc crct10dif_ce rfkill panfrost >>>>> snd_soc_meson_axg_sound_card snd_soc_meson_card_utils gpu_sched >>>>> meson_gxbb_wdt rtc_hym8563 pwm_meson meson_gxl rtc_meson_vrtc rc_khadas >>>>> meson_ir reset_meson_audio_arb realtek snd_soc_meson_g12a_tohdmitx >>>>> snd_soc_meson_codec_glue snd_soc_meson_axg_tdmout >>>>> snd_soc_meson_axg_frddr snd_soc_meson_axg_fifo axg_audio sclk_div >>>>> clk_phase mdio_mux_meson_g12a meson_dw_hdmi meson_drm meson_rng >>>>> dwmac_generic snd_soc_meson_axg_tdm_interface meson_canvas rng_core >>>>> dw_hdmi snd_soc_meson_axg_tdm_formatter dwmac_meson8b stmmac_platform >>>>> stmmac display_connector adc_keys pcs_xpcs nvmem_meson_efuse >>>>> [ 218.228329] CPU: 1 PID: 75 Comm: kworker/u8:2 Not tainted >>>>> 5.11.0-rc6-next-20210208 #2492 >>>>> [ 218.236343] Hardware name: Khadas VIM3L (DT) >>>>> [ 218.240579] Workqueue: brcmf_wq/mmc2:0001:1 brcmf_sdio_dataworker >>>>> [brcmfmac] >>>>> [ 218.247559] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) >>>>> [ 218.253506] pc : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>>> [ 218.259372] lr : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>>> [ 218.265237] sp : ffff80001327b870 >>>>> [ 218.268514] x29: ffff80001327b870 x28: 0000000000000003 >>>>> [ 218.273776] x27: 0000000000000218 x26: 0000000000000600 >>>>> [ 218.279036] x25: ffff000003a17678 x24: 0000000000000000 >>>>> [ 218.284296] x23: ffff8000121cfae8 x22: ffff800011b54000 >>>>> [ 218.289559] x21: ffff80001327bb18 x20: ffff00000277d000 >>>>> [ 218.294819] x19: ffff80001327ba40 x18: 00000002faf07f80 >>>>> [ 218.300081] x17: 0000000000004000 x16: 0000000000000000 >>>>> [ 218.305341] x15: 0000000000000380 x14: 0000000000000000 >>>>> [ 218.310603] x13: 0000000000000080 x12: 0000000000000000 >>>>> [ 218.315865] x11: 0000000000000000 x10: 0000000000001370 >>>>> [ 218.321125] x9 : ffff00006f995258 x8 : 000000009e0e7ca7 >>>>> [ 218.326387] x7 : ffff80001327b4a0 x6 : 0000000000000001 >>>>> [ 218.331648] x5 : 0000000000000001 x4 : 0000000000000000 >>>>> [ 218.336912] x3 : 0000000000000002 x2 : ffff8000121f4768 >>>>> [ 218.342171] x1 : 42fe1bd05e5eaa00 x0 : 0000000000000000 >>>>> [ 218.347435] Call trace: >>>>> [ 218.349854] meson_mmc_get_transfer_mode.isra.10+0xf8/0x130 >>>>> [ 218.355368] meson_mmc_request+0x74/0xb0 >>>>> [ 218.359250] __mmc_start_request+0xa4/0x2b0 >>>>> [ 218.363390] mmc_start_request+0x80/0xa8 >>>>> [ 218.367272] mmc_wait_for_req+0x68/0xd8 >>>>> [ 218.371066] mmc_submit_one.isra.17+0x78/0x148 [brcmfmac] >>>>> [ 218.376416] brcmf_sdiod_sglist_rw+0x324/0x4a8 [brcmfmac] >>>>> [ 218.381762] brcmf_sdiod_recv_chain+0x70/0x140 [brcmfmac] >>>>> [ 218.387110] brcmf_sdio_dataworker+0x614/0x17d0 [brcmfmac] >>>>> [ 218.392545] process_one_work+0x2a8/0x728 >>>>> [ 218.396510] worker_thread+0x48/0x460 >>>>> [ 218.400132] kthread+0x134/0x160 >>>>> [ 218.403323] ret_from_fork+0x10/0x18 >>>>> [ 218.406862] irq event stamp: 15834 >>>>> [ 218.410222] hardirqs last enabled at (15833): [<ffff800010f95804>] >>>>> _raw_spin_unlock_irq+0x3c/0x80 >>>>> [ 218.419107] hardirqs last disabled at (15834): [<ffff800010f895ac>] >>>>> el1_dbg+0x24/0x50 >>>>> [ 218.426869] softirqs last enabled at (15828): [<ffff800010010508>] >>>>> _stext+0x508/0x638 >>>>> [ 218.434717] softirqs last disabled at (15823): [<ffff8000100952ec>] >>>>> irq_exit+0x19c/0x1a8 >>>>> [ 218.442739] ---[ end trace dfc38bb4458b4c37 ]--- >>>>> # >>>>> >>>>> Surprisingly the same commands executed on the Khadas VIM3 board with >>>>> the same kernel don't trigger the warning. >>>> This may be because the VIM3 (G12A & G12B) has a broken SDIO controller using >>>> an internal SRAM as bounce buffer instead of the scatter/gather DMA, cf amlogic,dram-access-quirk. >>> Good to know, this explains why it works without an issue on VIM3. >>>>> Let me know if I can help debugging this issue. >>>> Simply remove the WARN_ONCE()... >>> Well, that WARN is not a big issue for me. I just wanted to help fixing >>> the real issue. If I understand right, the brcmfmac driver queues >>> incorrectly prepared sd list for the given transfer mode, what should be >>> fixed there. >> I think the issue comes from brcmfmac that should not provide unaligned data, >> but I think it's a global issue where these kind of details aren't specified/enforced. >> >>> On the other hand, if this is just a limitation of the meson mmc >>> controller on SM1/VIM3l, then imho there should not be a WARN there and >>> maybe the mentioned 'amlogic,dram-access-quirk' could be used to fix the >>> issue on VIM3l too. I've checked and it indeed 'fixes' the issue on that >>> board. >> This fix severely limits the performance so it's not a good fix here, >> the only fix I see here is to remove the WARN because the fact is that the DMA cannot handle >> unaligned data, and the SDIO device drivers should be fixed in order to achieve max >> performance on SDIO host drivers with DMA (it's usual to not support unaligned data >> when dealing with a DMA). > Do you plan to remove the warning ? I can push a quick patch if not. Feel free to send such 'fix'. I thought I would have some spare time to dig in the brcmfmac driver to fix the real source of the problem, but it turned out opposite... Best regards -- Marek Szyprowski, PhD Samsung R&D Institute Poland _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2021-04-07 10:01 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CGME20210209124819eucas1p29c9b481ef524a753ce79aa6ab580d0a7@eucas1p2.samsung.com>
2021-02-09 12:48 ` brcmfmac and unaligned sdio access on Khadas VIM3L Marek Szyprowski
2021-02-10 8:17 ` Neil Armstrong
2021-02-10 8:45 ` Marek Szyprowski
2021-02-10 8:52 ` Neil Armstrong
2021-04-07 8:45 ` Neil Armstrong
2021-04-07 10:00 ` Marek Szyprowski
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).